nwmgr_intl100.1m (2010 09)

ManualsBrandsHP ManualsSoftwareHP-UX Manpages

nwmgr_intl100(1M) nwmgr_intl100(1M)

The arguments all, extmib, and

mib are the only valid arguments for --stats for intl100

drivers. all is the default if no argument is provided with

--stats. It displays the same infor-

mation as

extmib which displays extended MIB statistics.

mib displays a subset of MIB statistics

of the interface.

View Interface Attributes

The following command can be used to display the current value of either all the attributes of the inter-

face (when the

all keyword is speciﬁed) or the speciﬁed attributes (when they are listed by name).

nwmgr [-g] -A {all | attr1

, attr2 , ...} -c lan_instance

nwmgr [--get] --attribute {all

| attr1 , attr2 , ...} --class_instance

lan_instance

Each attribute is listed on a separate line as a name-value pair.

View Interface Details

The following command can be used to get detail information about the interface.

nwmgr [-g] -q info -c

lan_instance

nwmgr [--get] --qualifier info --class_instance

lan_instance

This form displays interface-speciﬁc properties that are informational, often not conﬁgurable and

subject to variation across drivers. In the case of

intl100, the output is same as what is shown by:

nwmgr -g -v -c lan_instance

The

-q option provides more information about the subsystem.

Set Attribute Values

The following command can be used to set values to the speciﬁed attributes.

nwmgr -s -A attr1= value1, attr2= value2, ... -c lan_instance

nwmgr --set --attribute attr1=value1 , attr2=value2 ,...

--class_instance

lan_instance

The attributes that can be set are:

mac, mtu, and speed.

Save Current Attribute Values

The following command can be used to save the current attribute values in the conﬁguration ﬁle.

nwmgr -s -A all --sa --fr cu[rrent] -c lan_instance

nwmgr --set --attribute all --saved --from cu[rrent] --class_instance

lan_instance

This form ’freezes’ the current state of an interface; that is, it stores the current value of each attri-

bute of an interface in the conﬁguration ﬁle (

/etc/rc.config.d/hpintl100conf

) so that the

interface conﬁguration is saved across boots. The user can also run the start-up script later manu-

ally to apply the conﬁguration ﬁle values to the running kernel, by typing:

/sbin/rc2.d/S326hpintl100 start

. This feature allows a user to experiment with the

current values, and save the desired conﬁguration.

Set Attribute Values from Default Values

The following command can be used to set default values to all attributes (if

all is speciﬁed), or to

selected attributes (if the attribute names are listed).

nwmgr -s -A {all | attr1 , attr2 , ...} [--cu] --fr de[fault] -c lan_instance

nwmgr --set --attribute {all | attr1 , attr2 , ...} [--current] --from de[fault]

--class_instance lan_instance

This can be useful in rolling all the changes made to an interface since the time the system booted.

Reset an Interface

The following command can be used to reset an interface.

nwmgr -r -c lan_instance

nwmgr --reset --class_instance lan_instance

The interface is subjected to a PCI reset, which clears all previous state, including the interface

statistics. The interface is then re-programmed with the attribute values that were current before

the reset. Promiscuous mode and multicast addresses are preserved across the reset.

4 Hewlett-Packard Company − 4 − HP-UX 11i Version 3: September 2010