nettl.1m (2010 09)

n
nettl(1M) nettl(1M)
Used as a standalone option.
Used to display the filters and their respective states. If the filter is set or turned on for a
subsystem, the filter expression is displayed along with the status of the filter. If no filter
is set for a subsystem then the corresponding filter status is mentioned. If the attribute
all is specified then filter status is displayed for all the subsystems that currently sup-
port filters as listed above.
-removefilter all
-removefilter subsystem ...
(Abbr.: -rfl)
Used as a standalone option.
This option is used to remove filter expressions for subsystems that have been set with
the
setfilter command. If the attribute all
is specified then filters are removed for
all the subsystems that currently support filters as listed above.
Trace Memory Management
Memory used for tracing is made up of a circular linked list of trace buffers, each of which holds the trace
messages until they are written to the file. Trace messages are written to a buffer until it is filled, after
which the buffer is written to the file as a whole. While the buffer is being written to the file, the next
buffer in the list is used to hold the incoming trace messages. If no buffer is free to hold the incoming
trace messages, the messages will be dropped. Under this condition, additional trace buffers can be allo-
cated if the max_mem value is specified for
-mem option.
To achieve best tracing performance, the tracing algorithm imposes the following constraints:
a) Since a buffer is written to the file as a whole, the individual file size should be at least the buffer
size.
b) The additional amount of memory that can be allocated under heavy traffic given by (max_mem -
init_mem ) should be at least the buffer size.
where: buffer size =
MIN( init_mem /4, 32 MB )
Refer to examples 10 and 11 for further details.
Data File Management
Data files created by the tracing and logging facility require special handling by the facility that you must
be aware of. When files are created, they have the suffix
.LOG000 or
.TRC000 appended to them,
depending on whether they are log or trace files, respectively. This scheme is used to keep the files dis-
tinct for cases where you specify the same name in both places. Also, the files implement a type of circu-
lar buffer, with new data always going into the file appended with
.LOG000
or .TRC000. When a
logname
.LOG000 or tracename .TRC000 file is full, each log or trace is renamed to the next higher
number in its sequence; that is, a file with sequence number N is renamed as a file with sequence number
N+1 and a new file named logname.LOG000 or tracename .TRC000 is created. The number of files that
can exist simultaneously on the system can be specified by the -n option.
Note : The file name prefix (logname or tracename ) specified by the user must not exceed eight char-
acters so that the file name plus suffix does not exceed fourteen characters. Longer names are trun-
cated. To see the actual name of the trace or log file, use the
nettl -status all command.
Console Logging
Console logging is used to display significant log events on the system console. The values in the
/etc/nettlgen.conf file determine if console logging is to be started and the entries in the
/var/adm/conslog.opts file determine what log messages will be reported to the console. The
nettlconf command can be used to configure and maintain the information in the
/etc/nettlgen.conf file (see nettlconf (1M)). If changes are made to these files, nettl must be
stopped and restarted for the new information to take effect.
All log messages written to the console as a result of this configuration information are in a special short
form. If more information is desired on the console, the
netfmt formatter can be used to direct output to
the console device. This may be most useful in an X windows environment.
Console logging may be disabled if conservation of system resources is valued more than notification of
log events.
HP-UX 11i Version 3: September 2010 − 7 − Hewlett-Packard Company 7