HP-UX iSCSI Software Initiator Release Notes Revision B.11.11.03e for HP-UX 11i v1 Revision B.11.23.03e for HP-UX 11i v2 September 2004 (or later) Manufacturing Part Number : T1452-90010 E0705 Printed in US © Copyright 2005 Hewlett-Packard Development Company L.P.
Legal Notices The information in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this manual, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be held liable for errors contained herein or direct, indirect, special, incidental or consequential damages in connection with the furnishing, performance, or use of this material.
HP-UX iSCSI Software Initiator Release Notes Announcement The HP-UX iSCSI Software Initiator is a software implementation of the iSCSI protocol (RFC 3720) based on the HP-UX host TCP/IP stack. The iSCSI protocol defines a mass storage transport wedge between TCP and the SCSI Services layer. The HP-UX iSCSI Software Initiator is compliant with RFC 3720. To access the IETF iSCSI Specification RFC 3720, go to: http://www.ietf.org/rfc/rfc3720.
HP-UX iSCSI Software Initiator Release Notes What’s New Table 1 HP-UX iSCSI Software Initiator Documentation Availability Document Title Part Number url HP-UX iSCSI Software Initiator Support Guide T1452-90011 http://www.docs.hp.com See: “iSCSI (SCSI Over TCP/IP)” in the “Networking & Communications” section. HP-UX iSCSI Software Initiator Release Notes Revision B.11.11.03e and 11.23.03e, E0705 T1452-90010 http://www.docs.hp.
HP-UX iSCSI Software Initiator Release Notes Limitations What’s New In Revision B.11.23.03e of the HP-UX iSCSI Software Initiator • Correct ExpStatSN is sent during login phase In previous releases, out-of-order ExpStatSN was sent by the HP-UX iSCSI Software Initiator during login phase. This problem has been resolved. • islpd daemon configuration islpd daemon is by default not auto-started.
HP-UX iSCSI Software Initiator Release Notes Known Problems and Workarounds Known Problems and Workarounds Known Problems and Workarounds for the HP-UX iSCSI Software Initiator Revision B.11.11.03e • Problem: Kernel Registry Service states that information will be available prior to I/O initialization. However, kernel modules that use the Kernel Registry Service to store driver information are not available until after I/O initialization.
HP-UX iSCSI Software Initiator Release Notes Known Problems and Workarounds Initiator will return the errno “ENETUNREACH” (Network is unreachable), when iSCSI devices are accessed prior to the completion of network initialization. Once the network subsystem is initialized, the iSCSI Software Initiator will no longer return the errno “ENETUNREACH”. Any errno that is returned after network initialization will be the same as if the iSCSI Software Initiator were not installed on the system.
HP-UX iSCSI Software Initiator Release Notes Installation Requirements Installation Requirements Installation Requirements for the HP-UX iSCSI Software Initiator Revision B.11.11.03e The following patches, or any superseding patches, should be installed along with revision B.11.11.03e of the HP-UX iSCSI Software Initiator.
HP-UX iSCSI Software Initiator Release Notes HP-UX iSCSI Software Initiator Support Matrix HP-UX iSCSI Software Initiator Support Matrix NOTE Table 2 The following support matrix reflects the support status of Revisions B.11.11.03e and B.11.23.03e of the HP-UX iSCSI Software Initiator, at the time these Release Notes were published. The HP-UX iSCSI Software Initiator Support Matrix located at http://www.docs.hp.
HP-UX iSCSI Software Initiator Release Notes Software Availability in Native Languages Table 2 HP-UX iSCSI Software Initiator Support Matrix (Continued) HP-UX iSCSI Software Initiator Revision Revision B.11.23.
