Veritas 5.0 Installation Guide HP-UX 11i Version 2 First Edition Manufacturing Part Number: 5991-5508 September 2006 © Copyright 2006 Hewlett-Packard Development Company, L.P.
Legal Notices Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software Documentation and Technical Data for Commercial Items are licensed to the U.S. Government under vendor’s standard commercial license. The information contained herein is subject to change without notice.
Contents About This Document 1. System Requirements for Installing Veritas 5.0 Products Ignite-UX support for Veritas 5.0 Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Software Dependency. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Disk Space Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Patch Requirements. . . . . . . . . . . . . . . . . . . .
Contents Setting Up a VEA Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 6. Removing VxFS 5.0 and VxVM 5.0 Removing HP OnlineJFS 5.0. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing VxVM 5.0. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing Plexes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About This Document This document describes how to upgrade, install, and remove the Veritas 5.0 File System and, Veritas 5.0 Volume Manager products. Intended Audience This document is intended for system administrators responsible for installing and configuring UNIX systems with the Veritas suite of products. Readers are expected to have knowledge of the following: • System administration concepts • UNIX operating system concepts • UNIX File system concepts Document Organization The Veritas 5.
Typographic Conventions Table 2 describes the typographic conventions used in this document. Table 2 Typographic Conventions Typeface Usage Examples Computer output, files, directories, software elements such as command options, function names, and parameters Read tunables from the /etc/vx/tunefstab file. italic New terms, book titles, emphasis, variables replaced with a name or value See the Veritas 5.0 Installation Guide for details.
• Veritas 5.0 Volume Manager Release Notes • Veritas 5.0 Volume Manager Administrator’s Guide • Veritas 5.0 Volume Manager Troubleshooting Guide • Veritas 5.0 Volume Manager Migration Guide • Veritas 5.0 Enterprise Administrator User’s Guide Publication History • First Edition: September 2006, 5991-5508, HP-UX 11i Version 2 (B.11.23). HP Encourages Your Comments HP encourages your comments concerning this document. We are committed to providing documentation that meets your needs.
Phone: 0120.42.1231 or 0426-48-9310 (Inside Japan) +81.426.48.9312 (Outside Japan) Email: sw_codeword@hp.com • For information on latest available patches, see: http://itrc.hp.com • For technical support see: http://welcome.hp.com/country/us/en/support.
1 System Requirements for Installing Veritas 5.0 Products This chapter describes the system and patch requirements for installing VxFS 5.0 and VxVM 5.0 on HP-UX 11i version 2. The VxVM 5.0 and VxFS 5.0 products are supported on the September 2006 release of HP-UX 11i v2 or later. Ignite-UX support for Veritas 5.0 Products Ignite-UX C.6.9 is available on HP-UX 11i Version 2 September 2006 application media. However, it does not currently support cold installation of VxVM5.0 and VxFS 5.0.
System Requirements for Installing Veritas 5.0 Products Disk Space Requirements Table 1-1 describes the disk space requirements for installing the VxFS 5.0 product. Table 1-1 Minimum Space Requirement per Directory for VxFS 5.0 Product/Contents /standa /sbin VRTSvxfs 60MB 30MB 60MB 4MB 80MB - 154MB - - - 1MB - - 1MB - 8MB 3MB .5MB .5MB - 12MB /usr /opt /etc /var Total File System VRTSfsman File System manpages VRTSvlic Licensing Bundle a.
System Requirements for Installing Veritas 5.0 Products Patch Requirements • EnableVxFS version B.11.23.07 This bundle contains the following enhancement products: — FSLibEnh Enhancements to the LIBC libraries to understand VxFS disk layout Versions 6 and 7. — DiskQuota-Enh Enhancements to the various quota related commands to support large uids. — FSCmdsEnh Enhancements to the mount command to support VxFS 5.0.
System Requirements for Installing Veritas 5.0 Products This patch contains fixes that are required for correct operation of the vxupgrade and vxfsconvert commands in VxFS 5.0. However, this patch can be installed only after installation of VxFS5.0. • PHCO_35129 This patch is required for correct operation of DMP failover functionality. • PHKL_35130 This patch is required for correct operation of DMP failover functionality, and also to prevent possible data corruption when using vxdisksetup –iB.
2 Software Depot Content This chapter discusses the content of the Veritas 5.0 software bundles. Base-VxFS-50 Table 2-1 lists the products in the Base-VxFS-50 bundle: Table 2-1 Base-VxFS-50 Bundle Product Description VRTSvxfs Veritas File System Bundle 5.0 for HP-UX VRTSvlic Symantec License Utilities VRTSfsman Veritas File System Manuals NOTE The licensing bundle VRTSvlic is installed as part of Base-VxVM-50.
Software Depot Content Table 2-2 Base-VxVM-50 Bundle (Continued) Product Description VRTSicsco Symantec Infrastructure Core Services Common VRTSmh Veritas Storage Foundation Management Server by Symantec VRTSob Veritas Enterprise Administrator Service VRTSobc33 Veritas Enterprise Administrator Service Core VRTSobgui Veritas Enterprise Administrator VRTSpbx Symantec Private Branch Exchange VRTSvdid Veritas Device Identification API VRTSvmdoc Documentation for Veritas Volume Manager by Sym
3 Upgrading to VxFS 5.0 This chapter discusses the following VxFS upgrade paths: • VxFS 3.3 or 3.5 on 11i version 1 to VxFS 5.0 on 11i version 2 • VxFS 3.5 on 11i version 2 to VxFS 5.0 on 11i version 2 • VxFS 4.1 on 11i version 2 to VxFS 5.0 on 11i version 2 CAUTION NOTE You must ensure that: • You do not upgrade the operating system and the Veritas products simultaneously. HP recommends that you first upgrade the operating system and later upgrade the Veritas products.
Upgrading to VxFS 5.0 # bdf 2. To check for DLV 2 or 3 partitions present in the system (since these file systems cannot be mounted after upgrading to VxFS 5.0), enter the following: # fstyp -v 3. To upgrade file systems with DLV 2 or 3, before installing 5.0, complete the following steps ( You cannot upgrade from DLV 2 to DLV 4 directly. DLV4 is the lowest disk layout that is supported by VxFS 5.0.): a.
Upgrading to VxFS 5.0 VxFS 3.5 on 11i version 2 to VxFS 5.0 on 11i version 2 # vxupgrade -n 6 c. To upgrade a mounted VxFS file system from disk layout 4 to disk layout 7 # vxupgrade -n 5 # vxupgrade -n 6 # vxupgrade -n 7 9. To verify the conversion, enter the following: # fstyp -v VxFS 3.5 on 11i version 2 to VxFS 5.0 on 11i version 2 To upgrade from VxFS 3.5 on 11i version 2 to VxFS 5.
Upgrading to VxFS 5.0 a. To upgrade a mounted VxFS file system from disk layout 4 to disk layout 7 # vxupgrade -n 5 # vxupgrade -n 6 # vxupgrade -n 7 b. To upgrade a mounted VxFS file system from disk layout 5 to disk layout 7 # vxupgrade -n 6 # vxupgrade -n 7 c. To upgrade a mounted VxFS file system from disk layout 6 to disk layout 7 # vxupgrade -n 7 7.
Upgrading to VxFS 5.0 VxFS 4.1 on 11i version 2 to VxFS 5.0 on 11i version 2 # fsck -F vxfs -y -o full During pass 4, fsck displays several error messages that require a yes response to complete the conversion process. 6. VxFS file systems with disk layout 4, 5, and 6 can still be mounted with VxFS 5.0. However, to upgrade to disk layout version of mounted file systems to 7, use vxupgrade as follows: a.
Upgrading to VxFS 5.
4 Installing VxFS 5.0 and VxVM 5.0 This chapter describes how to install VxFS 5.0 and VxVM 5.0 with the swinstall(1M) command. Prior to installing Veritas 5.0 products, verify that all required patches described in “Patch Requirements” on page 10 are available at the time of installation. Mounting the HP-UX Serviceguard and Storage Management Products Media To mount the media, complete the following steps: Step 1. Insert the media into the drive and log in as root: $ su root Step 2.
Installing VxFS 5.0 and VxVM 5.0 been installed. The AVXFS and AVXVM products (contained within VxFS 5.0 and VxVM 5.0, respectively) will check the installed products and cause an installation failure for the 5.0 products on such systems. Installing Base-VxFS-50 You can install Base-VxFS-50 either in the non-interactive mode or in the interactive mode.
Installing VxFS 5.0 and VxVM 5.0 Installing Base-VxFS-50 1. To install Base-VxFS-50, enter the following: # swinstall -x autoreboot=true -s Figure 4-1 is displayed. You must mark the Base-VxFS-50 software in the SD Install window to start the installation. Figure 4-1 SD Install Window 2. Mark the Base-VxFS-50 software. 3. Select Actions, and click Install. Follow the on-screen instructions to complete the installation. The system reboots automatically after the installation is complete.
Installing VxFS 5.0 and VxVM 5.0 Verifying Base-VxFS-50 Installation To verify that the Base-VxFS-50 software is installed, enter the following: # swverify Base-VxFS-50 If the Base-VxFS-50 software is successfully installed on your system, you will see the following output: ======= 08/10/06 13:21:57 MDT BEGIN swverify SESSION (non-interactive) (jobid=) * Session started for user "root@". * Beginning Selection * Target connection succeeded for ":/".
Installing VxFS 5.0 and VxVM 5.0 Installing OnlineJFS (B3929FA) Installing OnlineJFS (B3929FA) in Non-Interactive Mode To install OnlineJFS (B3929FA) in the non-interactive mode, enter the following: # swinstall -x autoreboot=true -s B3929FA The following output is displayed: ======= 08/10/06 13:21:57 MDT BEGIN swinstall SESSION (non-interactive) (jobid=) * Session started for user "root@". * Beginning Selection * Target connection succeeded for ":/".
Installing VxFS 5.0 and VxVM 5.0 Figure 4-2 SD Install Window 2. Mark the B3929FA software. 3. Select Actions, and click Install. Follow the on-screen instructions to complete the installation. Verifying OnlineJFS (B3929FA) Installation # swverify B3929FA If the OnlineJFS (B3929FA) software is successfully installed on your system, you will see the following output: ======= 08/10/06 13:21:57 MDT BEGIN swverify SESSION (non-interactive) (jobid=) * Session started for user "root@".
Installing VxFS 5.0 and VxVM 5.0 Installing Base-VxVM-50 * Software selections: B3929FA,r=5.0.01.02,a=HP-UX_B.11.23_IA/PA,v=HP . . * Verification succeeded. NOTE: More information may be found in the agent logfile using the command "swjob -a log @ :/". ======= 08/10/2006 13:21:57 MDT END swverify SESSION (non-interactive) (jobid=) Installing Base-VxVM-50 You can install Base-VxVM-50 either in the non-interactive mode or in the interactive mode.
Installing VxFS 5.0 and VxVM 5.0 * Software selections: Base-VxVM-50,r=B.05.00,a=HP-UX_B.11.23_IA/PA,v=HP . . * Analysis and Execution succeeded. NOTE: More information may be found in the agent logfile using the command "swjob -a log @:/". ======= 08/10/06 13:21:57 MDT END swinstall SESSION (non-interactive) (jobid=) NOTE The installation of VxVM above, also installs the VEA service and client packages. Installation of VxVM 5.0 will pickup VxFS 5.0 as a corequisite.
Installing VxFS 5.0 and VxVM 5.0 Installing Base-VxVM-50 Figure 4-3 SD Install Window Step 2. Mark the Base-VxVM-50 software. Step 3. Select Actions, and click Install. Follow the on- screen instructions to complete the installation. The system reboots after the installation is complete.
Installing VxFS 5.0 and VxVM 5.0 * Beginning Selection * Target connection succeeded for ":/". * Software selections: Base-VxVM-50,r=B.05.00,a=HP-UX_B.11.23_IA/PA,v=HP . . * Verification succeeded. NOTE: More information may be found in the agent logfile using the command "swjob -a log @:/". ======= 08/10/06 13:21:57 MDT END swverify SESSION (non-interactive) (jobid=) You must install the patches PHCO_35129 and, PHKL_35130 after installing Base-VxVM-50.
Installing VxFS 5.0 and VxVM 5.0 Installing the Full VxVM (B9116CA) * Software selections: B9116CA,r=5.0,a=HP-UX_B.11.23_IA/PA,v=HP + Base-VxVM-50,r=B.05.00,a=HP-UX_B.11.23_IA/PA,v=HP . . * Analysis and Execution succeeded. NOTE: More information may be found in the agent logfile using the command "swjob -a log :/".
Installing VxFS 5.0 and VxVM 5.0 Figure 4-4 SD Install Window 2. Mark the B9116CA software. 3. Select Actions, and click Install. Follow the on-screen instructions to complete the installation. NOTE The B9116CA bundle contains a license for the full VxVM 5.0 functionality.
Installing VxFS 5.0 and VxVM 5.0 Installing VxVM 5.0 on a System with LVM Volume Groups * Target connection succeeded for ":/". * Software selections: B9116CA,r=5.0,a=HP-UX_B.11.23_IA/PA,v=HP . . * Verification succeeded. NOTE: More information may be found in the agent logfile using the command "swjob -a log :/". ======= 08/10/06 13:21:57 MDT END swverify SESSION (non-interactive) (jobid=) Installing VxVM 5.0 on a System with LVM Volume Groups Before installing VxVM 5.
Installing VxFS 5.0 and VxVM 5.
5 Setting Up VxFS 5.0 and VxVM 5.0 This chapter discusses how to set up VxFS 5.0 and VxVM 5.0. Setting Up VxFS 5.0 After installing VxFS 5.0, you can create a file system on a Veritas Volume Manager 5.0 volume or on an HP Logical Volume Manager (LVM) volume. For creating LVM volumes refer to appropriate LVM product documentation. If want to create a VxFS file system on a VxVM volume, you must configure VxVM first. See “Setting Up VxVM 5.0” on page 36.
Setting Up VxFS 5.0 and VxVM 5.0 NOTE When you use the swinstall command to install the VRTSfsman package, the VxFS 5.0 manpages are installed in the /opt/VRTS/vxfs5.0/man directory, and symbolic links to these manpages are created in the /opt/VRTS/man directory. When VxFS 5.0 is installed, the /opt/VRTS/vxfs5.0/man directory is automatically added to the /etc/MANPATH. Ensure that /opt/VRTS/vxfs5.
Setting Up VxFS 5.0 and VxVM 5.0 • Specify the name of the default disk group to be used by the commands if the -g option is not used to specify a disk group. • Choose whether to use enclosure-based naming for disks. This type of naming enables you to associate more meaningful disk-access names with disks in different arrays. NOTE For more information on setting up VxVM disk groups and volumes after installation, refer to section “Configuring Veritas Volume Manager” in the Veritas Volume Manager 5.
Setting Up VxFS 5.0 and VxVM 5.0 enclosures as separate physical entities. By configuring redundant copies of your data on separate enclosures, you can safeguard your data against failure of one or more enclosures. Step 3.
Setting Up VxFS 5.0 and VxVM 5.0 Setting Up a VEA Server The VEA server is automatically started at system reboot. However, you can also set up the VEA server later by completing the following procedure: Step 1. To check the status of the VEA service, enter the following: # /opt/VRTSob/bin/vxsvcctrl status Step 2.
Setting Up VxFS 5.0 and VxVM 5.
6 Removing VxFS 5.0 and VxVM 5.0 This chapter discusses how to remove the VxFS 5.0 and VxVM 5.0 products from your system. Removing HP OnlineJFS 5.0 NOTE You must remove HP OnlineJFS 5.0 before Base-VxFS-50 or you must remove them together. Also, removing OnlineJFS 5.0 does not automatically remove Base-VxFS-50.
Removing VxFS 5.0 and VxVM 5.0 Removing VxVM 5.0 VxVM 5.0 can be removed from systems only where the root disk is under HP Logical Volume Manager (LVM) control. If you try to remove VxVM 5.0 software from your system without completing the following preparatory steps, you will lose data and your system will be in an unstable state. Make sure that you take a full backup of the data on your system before removing VxVM 5.0 software. Before removing the VxVM 5.
Removing VxFS 5.0 and VxVM 5.0 Removing VxVM 5.0 NOTE The consolidation operation fails if you do not have sufficient space on a single sub-disk. Moving VxVM Volumes to LVM Volumes Before moving VxVM volumes to LVM volumes, ensure that the following steps are completed: Step 1. Backup your data to tape or other media. Step 2. Backup each file system individually, create new file systems on LVM logical volumes, and recover all volumes. Step 3. Move volumes incrementally on to logical volumes.
Removing VxFS 5.0 and VxVM 5.0 where vgvol is a newly created LVM volume group and lhome is a new logical volume. f. Replace the entry (if any) for the volume in /etc/fstab file with an entry for the newly created LVM logical volume. g. Mount the logical volume only if the VxVM volume was mounted before. h. Run the following command to remove the volume from Veritas Volume Manager control: # vxedit -rf rm volume_name i.
Removing VxFS 5.0 and VxVM 5.0 Removing VxVM 5.0 Removing Full VxVM (B9116CA) NOTE You must remove B9116CA before Base-VxVM or you must remove them together. To remove Full VxVM (B9116CA), enter the following: # swremove B9116CA The following output is displayed: ======= 08/10/06 13:21:57 MDT BEGIN swremove SESSION (non-interactive) (jobid=server-id) * Session started for user "root@server". * Beginning Selection * Target connection succeeded for ":/". * Software selections: B9116CA,r=5.
Removing VxFS 5.0 and VxVM 5.0 * Target connection succeeded for ":/". * Software selections: Base-VxVM-50,r=B.05.00,a=HP-UX_B.11.23_IA/PA,v=HP . . * Execution succeeded. NOTE: More information may be found in the agent logfile using the command "swjob -a log @ :/". ======= 08/10/06 13:21:57 MDT END swremove SESSION (non-interactive) (jobid=) NOTE After removing the Veritas products, the system reboots.
Removing VxFS 5.0 and VxVM 5.0 Removing Base-VxFS-50 • To remove the Base-VxFS-50, enter the following: # swremove -x autoreboot=true Base-VxFS-50 The following output is displayed: ======= 08/10/06 13:21:57 MDT BEGIN swremove SESSION (non-interactive) (jobid=) * Session started for user "root@". * Beginning Selection * Target connection succeeded for ":/". * Software selections: Base-VxFS-50,r=B.05.00,a=HP-UX_B.11.23_IA/PA,v=HP . .
Removing VxFS 5.0 and VxVM 5.
A Files Added and Modified After VxFS Installation Files Added After VxFS Installation Table A-1 lists the files added after installing VxFS 5.0 and VxVM 5.0. Table A-1 Files Added File Description /usr/conf/lib/libvxfs50.a Kernel library for VxFS 5.0 /sbin/lib/mfsconfig.d/vxfs50 VxFS 5.0 command configuration file /usr/lib/libxdsm.a DMAPI library /usr/lib/libvxfsutil.a VxFS 5.0 APIs library /usr/conf/mod/fdd Quick I/O module /sbin/fs/vxfs5.0/ [bcheckrc, VxFS 5.
Files Added and Modified After VxFS Installation /usr/sbin/ [fsclustadm, qiomkfile, qioadmin, VxFS 5.0 commands and Quick I/O commands qiostat vxfsckd, vxgetmsg] /usr/lib/ [vxckptpriv.so, Dynamic libraries for VxFS 5.0 APIs vxfspriv.so, vxfsutil.so, .libvxfsutil.so] /usr/lib/pa20_32/ [vxckptpriv.so, 32-bit dynamic libraries for VxFS 5.0 APIs vxfspriv.so, vxfsutil.so, .libvxfsutil.so] /usr/lib/pa20_64/ [vxckptpriv.so, 64-bit dynamic libraries for VxFS 5.0 APIs vxfspriv.so, vxfsutil.so, .libvxfsutil.
