HP-UX vPars and Integrity VM V6.3 Release Notes (762790-001, July 2014) (Edition: 1.6)
Table Of Contents
- HP-UX vPars and Integrity VM V6.3 Release Notes
- Contents
- HP secure development lifecycle
- 1 Introduction
- 2 Installing or upgrading to HP-UX vPars and Integrity VM V6.3
- 3 New functionality and changes from earlier versions
- 3.1 New features and enhancements
- 3.1.1 Enhanced capability for emulated platform NVRAM (Non Volatile RAM)
- 3.1.2 Increased resources for Integrity VM guests
- 3.1.3 Dynamic addition of I/O devices
- 3.1.4 PCI OLR support on Superdome 2 VSPs
- 3.1.5 AVIO Networking improvements
- 3.1.6 AVIO Storage improvements
- 3.1.7 Greater flexibility for online VM migration
- 3.1.8 Improvements to Virtual Server Management
- 3.1.9 Improvements to VSP resource management
- 3.2 Changes from previous versions
- 3.1 New features and enhancements
- 4 Known problems, limitations, and workarounds
- 4.1 CPU/vCPU
- 4.2 Memory
- 4.3 Networking
- 4.3.1 Cannot remove a VLAN-based vNIC if the VLAN has been removed
- 4.3.2 hpvmhwmgmt might add ports in link aggregates into the DIO pool
- 4.3.3 DIO limitations
- 4.3.4 Known issues or limitations with DIO support for 10GigEthr-02 (iexgbe)
- 4.3.5 DIO-capable functions might become inconsistent with information in vPar or VM device database
- 4.3.6 When DIO device is assigned or removed from the DIO pool, error messages appear multiple times
- 4.4 Storage
- 4.4.1 Presenting a Logical Volume created on iSCSI devices as AVIO backing store to a guest not supported
- 4.4.2 Size change operations on a SLVM volume based backing store do not get reflected in the vPar or VM
- 4.4.3 The hpvmdevinfo command may not list the correct host to guest device mapping for legacy AVIO backing stores
- 4.4.4 Probe of NPIV HBAs for Fibre Channel targets may timeout
- 4.4.5 NPIV LUNs not shown by default invocation of ioscan
- 4.4.6 The interrupt balancing daemon must not be enabled in vPars and Integrity VM guests
- 4.4.7 Online addition of DMP device as backing store is not supported
- 4.5 VM <—> vPar conversion
- 4.6 Migration, Suspend, and Resume operations on Integrity VM guests
- 4.6.1 Use of -F with hpvmmigrate on a suspended VM can cause VM to be not runnable on both source and target
- 4.6.2 Copy of a vPar or VM might be left in runnable state if migration fails
- 4.6.3 Interrupt migration of vNICs during Online guest migration can result in network disconnectivity
- 4.6.4 Physical NIC link state change during hpvmsuspend to hpvmresume may result vNIC in down state
- 4.6.5 Offline migration of a guest- with multiple DIO resources might succeed with errors if the DIO devices are added under the same label
- 4.7 User interface—CLI
- 4.8 Known system crashes, panics, hangs and MCAs
- 5 HP-UX vPars and Integrity VM support policy
- 5.1 Support duration
- 5.2 VSP firmware requirements
- 5.3 VSP server and OS support
- 5.4 HP-UX version support for vPar and Integrity VM guests
- 5.5 Storage device support for vPar and Integrity VM guests
- 5.6 Network device support for vPar and Integrity VM guests
- 5.7 Support for migration of vPars and Integrity VMs
- 6 Support and other resources
- 7 Documentation feedback
6 Support and other resources
6.1 Contacting HP
6.1.1 Before you contact HP
Be sure to have the following information available before you call contact HP:
• Technical support registration number (if applicable)
• Product serial number
• Product model name and number
• Product identification number
• Applicable error message
• Add-on boards or hardware
• Third-party hardware or software
• Operating system type and revision level
6.1.2 HP contact information
For the name of the nearest HP authorized reseller:
• See the Contact HP worldwide (in English) webpage (http://welcome.hp.com/country/us/
en/wwcontact.html).
For HP technical support:
• In the United States, for contact options see the Contact HP United States webpage (http://
welcome.hp.com/country/us/en/contact_us.html). To contact HP by phone:
◦ Call 1-800-HP-INVENT (1-800-474-6836). This service is available 24 hours a day, 7
days a week. For continuous quality improvement, calls may be recorded or monitored.
◦ If you have purchased a Care Pack (service upgrade), call 1-800-633-3600. For more
information about Care Packs, see the HP website at HP Care Packs.
◦ In other locations, see the Contact HP worldwide (in English) webpage (http://
welcome.hp.com/country/us/en/wwcontact.html)
6.1.3 HP Insight remote support
HP strongly recommends that you install HP Insight Remote Support software to complete the
installation or upgrade of your product and to enable enhanced delivery of your HP Warranty,
HP Care Pack Service or HP contractual support agreement. HP Insight Remote Support supplements
your monitoring, 24x7 to ensure maximum system availability by providing intelligent event
diagnosis, and automatic, secure submission of hardware event notifications to HP, which will
initiate a fast and accurate resolution, based on your product’s service level. Notifications may be
sent to your authorized HP Channel Partner for on-site service, if configured and available in your
country. The software is available in two variants:
• HP Insight Remote Support Standard: This software supports server and storage devices and
is optimized for environments with 1-50 servers. Ideal for customers who can benefit from
proactive notification, but do not need proactive service delivery and integration with a
management platform.
• HP Insight Remote Support Advanced: This software provides comprehensive remote monitoring
and proactive service support for nearly all HP servers, storage, network, and SAN
environments, plus selected non-HP servers that have a support obligation with HP. It is
6.1 Contacting HP 47