HP-UX vPars and Integrity VM V6.1.5 Administrator Guide (5900-2295, April 2013)

4 Upgrading the VSP from previous versions of Integrity VM.............................43
4.1 Upgrading the VSP from previous versions of Integrity VM V3.x to Integrity VM V6.1.5...............43
4.1.1 Study the current HP-UX 11i v2 to HP-UX 11i v3 update documentation...............................45
4.1.2 Analyze HP-UX 11i v2 based Integrity VM server............................................................45
4.1.2.1 Run the HP-UX msv2v3check tool...........................................................................46
4.1.2.2 Determine HP-UX 11i v3 memory and system disk requirements.................................47
4.1.2.3 Determine version requirements for HP-UX OE and vPars and Integrity VM.................47
4.1.3 Decide whether to perform a cold-install or an update....................................................48
4.1.4 Perform required hardware and firmware upgrades........................................................49
4.1.5 Perform either a cold-install or an update.......................................................................49
4.1.6 Verifying vPars/VM after installing layered products.......................................................51
4.1.7 Upgrade troubleshooting issues...................................................................................51
4.2 Updating previous versions of the VSP and VM guests to Integrity VM V6.1.5............................51
5 Using NPIV with vPars and Integrity VM......................................................55
5.1 NPIV can satisfy these requirements.....................................................................................55
5.2 Dependencies and prerequisites.........................................................................................55
5.3 NPIV – supported limits.....................................................................................................56
5.3.1 Verifying that the VSP can support NPIV.......................................................................56
5.3.2 WWNs – Finding and using WWNs..........................................................................57
5.3.3 Configuring an NPIV HBA (vHBA)................................................................................57
5.3.3.1 Specifying an NPIV HBA resource........................................................................57
5.3.3.2 vPar commands in NPIV context..........................................................................58
5.4 Migrating VM guests with NPIV HBAs.................................................................................60
6 Creating virtual partitions..........................................................................61
6.1 Creating a virtual partition.................................................................................................61
6.1.1 Specifying CPU/Core min and max limits......................................................................66
6.1.2 Adding and deleting CPUs/Cores by total.....................................................................66
6.2 Booting a virtual partition..................................................................................................66
6.3 Modifying a virtual partition...............................................................................................67
6.4 Viewing information specific to a virtual partition..................................................................67
6.5 Resetting a virtual partition.................................................................................................68
6.6 Removing a virtual partition...............................................................................................69
6.6.1 Removing and recreating a virtual partition...................................................................69
6.7 Reserved resources and resource over-commitment................................................................70
6.7.1 Resource over-commitment...........................................................................................70
6.8 Installing the HP-UX Operating Environment on a vPar...........................................................71
6.8.1 Installing HP-UX 11i on a vPar using an Ignite-UX server..................................................71
6.9 Setting up a vPar to use NPIV HBAs....................................................................................72
6.9.1 Configuring storage for a vPar with NPIV HBAs..............................................................72
6.9.2 Identifying NPIV HBAs and devices in a vPar................................................................73
6.9.3 Installing the vPar image on NPIV disks........................................................................73
6.10 Deactivating a vPar configuration......................................................................................73
6.11 vPar V6.1.5 local MCA support..........................................................................................74
6.12 Recovering a nonresponsive vPar.......................................................................................75
7 Creating virtual machines..........................................................................77
7.1 Specifying virtual machine characteristics..............................................................................77
7.1.1 Virtual machine name..................................................................................................78
7.1.2 Virtual machine type...................................................................................................78
7.1.3 Guest operating system type........................................................................................79
4 Contents