HP-UX 11i v3 Installation and Update Guide, March 2011 (Edition 9.2)

Table 15 Known install and update problems (continued)
Description/actionProblem
This problem does not affect new installations where the cimsrvr user and group
are present before NIS, LDAP, or other network services are configured; or minor
upgrades of HP WBEM Services where the cimsrvr user and group are present
from an installation of HP WBEM versions earlier than version A.02.07.
If you have installed HP-UX Security Containment Extensions (ContainmentExt
bundle) version B.11.31.01 (which includes the CompartmentLogin and
HP-UX Security Containment
Extensions version B.11.31.01
might produce unexpected
behaviors and swverify errors
ContainmentWiz products) from the HP-UX 11i v3 March 2009, September
2009, or March 2010 OE media, you might experience unexpected behaviors
while using HP-UX Compartment Login and HP-UX Containment Wizard.
In addition, when you update the OE with ContainmentExt B.11.31.01 to a
newer OE version, you might find swverify errors that indicate
ContainmentExt, CompartmentLogin, and/or ContainmentWiz are not
found on the system.
What to do
Update the product bundle to version B.11.31.01.01 or later, which can be
obtained from http://software.hp.com, or from the HP-UX 11i v3 September 2010
OE media. Then you can install or update to your target HP-UX 11i v3 OE media.
New installation of a P700m controller is not recommended on HP-UX 11i v3
releases prior to March 2010. HP-UX 11i v3 Releases prior to March 2010 might
Issues with HP Smart Array P700m
RAID controllers
not guarantee that P700m Device Special Files (DSFs) are persistent between
releases. This can cause data on arrays to become unavailable after you upgrade
to the March 2010 (or later) release of HP-UX 11i v3.
What to do
If you have an HP Smart Array P700m already configured on any of the following
releases, you must contact HP Support before you upgrade to the March 2010
release:
• HP-UX 11i v3 March 2009 Release
• HP-UX 11i v3 June 2009 WEB release
• HP-UX 11i v3 September 2009 Release
• HP-UX 11i v3 September 2009 WEB Release
If you are considering a new installation of an HP Smart Array P700m Controller,
HP recommends that you configure it on HP-UX 11i v3 March 2010 release or
later. If you have a Smart Array P700m controller configured on any HP-UX 11i
v3 release prior to March 2010, you must contact HP Support before upgrading
to a newer release. For further information on contacting HP support, see Chapter 9:
“Support and other resources” (page 67).
When executing drd runcmd update-ux using a directory depot (or mounted
media) that resides on the active system image, the command fails with this error:
drd runcmd update-ux fails
with local source depots
ERROR: The expected depot does not exist at
"<depot_name>"
What to do
In order to use a directory depot on the active system image, you will need to
install March 2010 (or later) Dynamic Root Disk (DRD), Software Manager (SWM),
and Software Distributor (SW-DIST) products from an OE depot. This must be done
before the clone is created, so the new DRD, SWM, and SW-DIST are on the active
system and on the clone.
The following assumes the OE depot is at /var/depots/1003-DCOE. This must
be executed as root:
swinstall -x autoselect_dependencies=false \
-s /var/depots/1003-DCOE \
DRD SWM SW-DIST PHCO_36525
76 Harmless messages and known problems