HP-UX HB v13.00 Ch-02 - System Boot

HP-UX Handbook – Rev 13.00 Page 9 (of 14)
Chapter 02 System Boot
October 29, 2013
Boot
: disk(0/0/2/0.0.0.0.0.0.0;0)/stand/vmunix
9310208 + 1843200 + 1733192 start 0x1f0ae8
alloc_pdc_pages: Relocating PDC from 0xf0f0000000 to 0x1fb01000.
gate64: sysvec_vaddr = 0xc0002000 for 2 pages
NOTICE: autofs_link(): File system was registered at index 3.
NOTICE: cachefs_link(): File system was registered at index 5.
NOTICE: nfs3_link(): File system was registered at index 6.
System Console is on the Built-In Serial Interface
Logical volume 64, 0x3 configured as ROOT
Logical volume 64, 0x2 configured as SWAP
Logical volume 64, 0x2 configured as DUMP
Swap device table: (start & size given in 512-byte blocks)
entry 0 - major is 64, minor is 0x2; start = 0, size = 1048576
Starting the STREAMS daemons-phase 1
Checking root file system.
file system is clean - log replay is not required
Root check done.
Memory Information:
physical page size = 4096 bytes, logical page size = 4096 bytes
Physical: 524288 Kbytes, lockable: 363332 Kbytes, available: 417652 Kbytes
Step 4: Starting the Subsystems
The /etc/init process (pid 1) gets forked off which, depending on the passed init state, starts
working through /etc/inittab or launches a shell in the case of a single user or LVM
maintenance boot.
The following is the default inittab for HP-UX 11.11:
# cat /etc/inittab
#ups::respawn:rtprio 0 /usr/lbin/ups_mond -f /etc/ups_conf
init:3:initdefault:
ioin::sysinit:/sbin/ioinitrc >/dev/console 2>&1
tape::sysinit:/sbin/mtinit > /dev/console 2>&1
muxi::sysinit:/sbin/dasetup </dev/console >/dev/console 2>&1 # mux init
stty::sysinit:/sbin/stty 9600 clocal icanon echo opost onlcr ixon icrnl ignpar
</dev/systty
brc1::bootwait:/sbin/bcheckrc </dev/console >/dev/console 2>&1 # fsck, etc.
link::wait:/sbin/sh -c "/sbin/rm -f /dev/syscon; \
/sbin/ln /dev/systty /dev/syscon" >/dev/console 2>&1
cprt::bootwait:/sbin/cat /etc/copyright >/dev/syscon # legal req
sqnc::wait:/sbin/rc </dev/console >/dev/console 2>&1 # system init
#powf::powerwait:/sbin/powerfail >/dev/console 2>&1 # powerfail
cons:123456:respawn:/usr/sbin/getty console console # system console
#ttp1:234:respawn:/usr/sbin/getty -h tty0p1 9600
#ttp2:234:respawn:/usr/sbin/getty -h tty0p2 9600
#ttp3:234:respawn:/usr/sbin/getty -h tty0p3 9600
#ttp4:234:respawn:/usr/sbin/getty -h tty0p4 9600
#ttp5:234:respawn:/usr/sbin/getty -h tty0p5 9600
krsd:123456:respawn:/sbin/krsd -i