Cartridge Access Port Installation Instructions

ManualsBrandsHP ManualsStorageHP Surestore Tape Library Model 20/700

62104 1

HP Surestore Tape Library 20/700 A5601A

Cartridge Access Port Installation

Instruction

(for HP field service use only)

CAUTION: The HP tape library Cartridge Access Port is not customer installable or

replaceable. Any servicing, adjustment, maintenance or repair must be performed only

by authorized HP service-trained personnel.

Note to Customer Engineer: This installation may add new technology to the library

that older user’s guides do not address. Please remind the customer that the latest user

documentation is available from the HP Customer Care website: http://www.hp.com/go/

support.

■ Materials Included

■ Installation Notes

• Confirm with the customer System Administrator that the tape library can be powered

off.

• Observe proper power down and power on procedures, as described in the

Installation or Service Manual.

Table 1. Materials List

Part Quantity

I/I CAP 1

CAP TLA 1

6-32 x 3/8-in. Torx Screws 10

1/4-20 x 1/2 Long Screws 4

CAP B EMI Shield 1

Five Cell Magazine Assembly 4

Summary of content (6 pages)

PAGE 1
HP Surestore Tape Library 20/700 A5601A Cartridge Access Port Installation Instruction (for HP field service use only) CAUTION: The HP tape library Cartridge Access Port is not customer installable or replaceable. Any servicing, adjustment, maintenance or repair must be performed only by authorized HP service-trained personnel. Note to Customer Engineer: This installation may add new technology to the library that older user’s guides do not address.
PAGE 2
■ CAP Install 1. Have the operator take the library and all tape drives offline and power off the tape library. 2. Obtain key and open front cartridge area door of the tape library. 3. Remove CAP A EMI SHIELD (refer to item 3 of the graphic) and window assembly from CAP B mounting location and set aside. Use a T15 Torx driver. A total of 10 No. 6-32 x 3/ 8-in. Torx Pan Head screws must be removed (see Figure 1). Note: The CAP EMI SHIELD may only have six screws on some older 20/700 models. Figure 1.
PAGE 3
Figure 1. Removing CAP A EMI Shield and Window Assembly (Continued) Removing CAP A EMI SHIELD and Window Assembly (a5601a_01) 1. 2. 3. 4. 5. CAP B Mounting Location Tape Library CAP Door CAP A EMI Shield 6-32 x 3/8-in. Torx Pan Head Screws (10x) Window Assembly 4. Reinstall CAP A EMI SHIELD removed in step 2 using a T15 Torx driver and five No. 632 x 3/8 Torx Pan Head screws. Please note that some older models of 20/700 require only three screws.
PAGE 4
Figure 2. CAP Installation CAP Installation (a5601a_02) 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 6-32 x 3/8-in. Pan Head Screw for CAP B Shield (5x) CAP A EMI Shield Top CAP Mounting Bracket 1/4-20 x 1/2-in. Long Screw (4x) CAP B EMI Shield Bottom CAP Mounting Bracket Locating Pin 6-32 x 3/8-in. Pan Head Screw for CAP A Shield (5x) Upper Door Locating Pin Top CAP Mounting Bracket 7. Fasten CAP to the tape library door hinges with four 1/4-20 x 1/2 long screws. Tighten screws using T30 Torx driver. 8.
PAGE 5
Head screws. Check CAP B for rotation by manually rotating the cylindrical door. Please note that some older models of 20/700 require only three screws. If the CAP cannot rotate freely, realign the CAP EMI SHIELD (see Figure 2). 9. Connect CAP B motor cable to cable fastened to upper tape library door hinge. The connector is labeled MB (refer to item 3 of Figure 3). Figure 3. CAP Motor Cables Motor Cables (a5601a_03) 16. 17. 18. 19.
PAGE 6
Figure 4. CAP Installation CAP Installation (a5601a_02) 20. Magazine 12. Close LSM doors and lock. 13. Verify that the tape library initializes and audits properly. 14. Test the operation of CAP A and CAP B by pressing CAP B button on OP panel. Open and Close. 15. Return unit to customer.