HP XP P9000 Remote Web Console Messages Abstract This document lists the error codes and error messages for HP XP P9000 Remote Web Console for HP XP P9000 disk arrays, and provides recommended action for the error conditions.
© Copyright 2010, 2014 Hewlett-Packard Development Company, L.P. Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor's standard commercial license. The information contained herein is subject to change without notice.
Contents 1 Remote Web Console messages and error codes............................................6 Remote Web Console messages.................................................................................................6 Message window format...........................................................................................................6 Advanced message window......................................................................................................
Part code 03305..................................................................................................................121 6 Messages (part code group 04nnn)..........................................................127 Part code 04005..................................................................................................................127 Part code 04010..................................................................................................................
Part Part Part Part Part code 09110...................................................................................................................319 code 09205..................................................................................................................321 code 09210...................................................................................................................324 code 09605..........................................................................................
1 Remote Web Console messages and error codes This chapter describes the messages and error codes issued by the Remote Web Console software for the P9500 storage system. Remote Web Console messages Figure 1-1 and Figure 1-2 show typical Remote Web Console message windows.
Recommended action The part code is the ID (four- or five-digit number) of the application that issued the message. In some cases, the number of digits in the message may not match the number of digits described in this manual.
Figure 3 Example of advanced message window 2 When multiple errors occur at the same time, the errors are listed by error code number on the message window as shown above. To open and read one of the error messages, click the error code number for the error. The advanced message window can also be accessed from the task window. (For details about the task window, see the HP XP P9000 Remote Web Console User Guide.
Remote Console-Remote Web Console error codes To find solutions to the Remote Web Console for P9500 errors, refer to Table 1 (page 10) and subsequent tables in this manual, or refer to the Troubleshooting chapter in the user guide for the program product (for example, Business Copy) causing the error. Table 1 (page 10) and subsequent tables list the error codes and error messages for Remote Web Console and provide the recommended action and severity levels for the error conditions.
2 Messages (part code group 00nnn) This chapter lists the Remote Web Console error messages with part code 00000 to 00999 and provides recommended action for each error. Part code 00001 Table 1 Error codes (part code 00001) Part Code Error Number Error Message Recommended Action Severity Level 00001 001000 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. If this problem persists please contact HP Technical Support.
Table 1 Error codes (part code 00001) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00001 004006 An error occurred. If this problem persists, please contact HP Technical Support. Please contact HP Technical Support. E 00001 004007 An error occurred. If this problem persists, please contact HP Technical Support. Please contact HP Technical Support. E 00001 004008 An error occurred. If this problem persists, please contact HP Technical Support.
Table 1 Error codes (part code 00001) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00001 005400 Failed to access the monitoring data A different user might open one of the following W because accessing the monitoring data windows or run the export tool. In this case, wait on the SVP is busy. until one of the users moves to a different window or exits the export tool. • [Usage Monitor] window of the Continuous Access Synchronous.
Table 1 Error codes (part code 00001) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00001 005636 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. If this problem persists, please contact HP Technical Support. E 00001 005637 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. If this problem persists, please contact HP Technical Support.
Table 1 Error codes (part code 00001) (continued) Part Code Error Number Error Message Recommended Action persists, the proxy server may be the cause of the problem. Please contact your network administrator. If your network does not have any problem, and this problem persists, please contact HP Technical Support. use a proxy server, the old version of the program could remain in the cache of the proxy. Contact your network administrator to clear the proxy cache.
Table 1 Error codes (part code 00001) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00001 065734 CVAE version information ID is invalid. Check the setting, and then retry the operation. CVAE version information ID is invalid. Check the E setting, and then retry the operation. 00001 066100 The Login could not be performed Please contact HP Technical Support. because a function failed to start during SVP initialization. E Please contact HP Technical Support.
Table 2 Error codes (part code 00002) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00002 002015 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 00002 002016 The array is refreshing, or some other user is registering the setting. Wait, then retry the operation. W 00002 002145 An error occurred while connecting to the storage system. Wait, then retry the operation.
Table 2 Error codes (part code 00002) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00002 007060 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 00002 007111 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 00002 007211 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 3 Error codes (part code 00003) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00003 002004 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 00003 002005 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 00003 002006 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 3 Error codes (part code 00003) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00003 002100 An error occurred while connecting to the storage system. The configuration may be inconsistent. Click [Refresh All] on the [File] menu, then refresh W the configuration. 00003 003000 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 00003 003001 An error occurred during SVP processing.
Table 4 Error codes (part code 00004) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00004 006037 Unexpected error occurred. Please refresh the array configuration. The storage system status is invalid. If the same problem persists despite retrying, please contact HP Technical Support. E 00004 008010 Unexpected error occurred. Please refresh the array configuration. The storage system status is invalid.
Part code 00007 Table 7 Error codes (part code 00007) Part Code Error Number Error Message Recommended Action Severity Level 00007 006012 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. If this problem persists, please contact HP Technical Support. E 00007 006022 File access error occurred.
Part code 00010 Table 8 Error codes (part code 00010) Part Code Error Number Error Message 00010 006023 An error occurred during processing. If If this problem persists, please contact HP this problem persists, please contact HP Technical Support. Technical Support. 00010 006027 A network error occurred. The causes might be one of the following. • The SVP was not ready. • An error occurred in the SVP. • A timeout error occurred while communicating with the SVP.
Table 8 Error codes (part code 00010) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00010 059013 The specified file already exists. Do you To overwrite the file, click [OK]. Otherwise, click want to overwrite this file? [Cancel]. W 00010 059109 The free space to store the audit log file Download the audit log file. has run out. The old audit log information is deleted because it is overwritten with the new audit log information.
Table 11 Error codes (part code 00110) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00110 009100 Do you want to exit? - i 00110 009101 Do you want to cancel? To cancel, click [OK]. i 00110 009102 Do you want to apply? To execute the operation in Preview, click [OK], if not click [Cancel]. i 00110 009104 Do you want to change the mode? - i 00110 009105 The value that is under setup is not reflected yet.
Table 11 Error codes (part code 00110) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00110 067005 Configuration information on the storage Click [Refresh All] on the File menu and refresh system and the configuration information the configuration information. on the SVP became inconsistent. Click [Refresh All] on the File menu and refresh the configuration information.
Table 13 Error codes (part code 00190) (continued) Part Code Error Number Error Message Recommended Action Severity Level Wait until the collection is complete, and then retry the operation. 00190 006017 The user account list was modified by Reboot the process. the administrator while you were making settings. - 00190 006018 An authentication error occurred (Dump Click the close button and close the window. file download authentication). Log in again to the Download Dump Files function.
Table 13 Error codes (part code 00190) (continued) Part Code Error Number Error Message Recommended Action Severity Level Click [OK] to continue the operation. i • If a setting operation is being performed from HCS, the HCS setting operation will fail with an error. • The renewal of the SSL certificate will have a significant impact on the system. To avoid any SVP failures caused by this operation, be sure to confirm the contents of the certificate and the secret key to be set up.
Part code 00221 Table 14 Error codes (part code 0221) Part Code Error Number Error Message Recommended Action Severity Level 00221 105007 The re-entered password does not match Verify the settings, and then retry the operation. the one entered previously. W 00221 105008 The re-entered secret does not match the Verify the settings, and then retry the operation. one entered previously.
Table 15 Error codes (part code 00222) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00222 105318 The domain name of authentication server is not input. This is a compulsory input item. W 00222 105319 The domain name of authentication server is too long. Enter with 1 to 255 characters. W 00222 105320 Invalid characters are used in the domain name of authentication server. Enter with alphanumeric characters and symbols ( - . ).
Table 15 Error codes (part code 00222) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00222 105338 The password of authentication server is not input. This is a compulsory input item. W 00222 105339 The password of authentication server is too long. Enter with 1 to 256 characters. W 00222 105340 Invalid characters are used in the specified password of authentication server. Enter with alphanumeric characters and symbols ( ! # $ % & ' ( ) * + - .
Table 15 Error codes (part code 00222) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00222 105357 Other than the numeric characters are input to the secondary port number of authentication server. Enter with numeric characters. W 00222 105358 The value that can be input to the secondary port number of the authentication server is 1 to 65535. Set a value within the range.
Table 15 Error codes (part code 00222) (continued) Part Code Error Number Error Message 00222 105379 Invalid characters are used in the Enter with alphanumeric characters and symbols specified domain name of external user ( - . ). group mapping. W 00222 105380 The base DN of external user group mapping is not input. This is a compulsory input item. W 00222 105381 The base DN of external user group mapping is too long. Enter with 1 to 255 characters.
Table 15 Error codes (part code 00222) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00222 105398 The number of retries for the external user group mapping is not input. This is a compulsory input item. W 00222 105399 Other than the numeric characters are input to the specified number of retries of authentication server. Enter with numeric characters. W 00222 105400 The value that can be input to the Set a value within the range.
Table 15 Error codes (part code 00222) (continued) Part Code Error Number Error Message Recommended Action 00222 105417 Invalid characters are used in the Enter with alphanumeric characters and symbols specified user name for connecting test. ( ! # $ % & ' * + - . / = ? @ ^ _ `{ | } ~ ). W 00222 105418 The password for connecting test is not input. This is a compulsory input item. W 00222 105419 The password for connecting test is too long. Enter with 1 to 128 characters.
Table 15 Error codes (part code 00222) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00222 106055 Failed to delete the user account. Check the following contents. W • If the specified user exists. • If there is no built-in user in the specified users. • If there is a valid local authentication user who belongs to the Administrator User Group except the specified user, then retry the operation.
Table 15 Error codes (part code 00222) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00222 106069 You cannot remove the selected users, because they will not belong to any groups. Check the number of the groups which the selected users belong to. W 00222 106070 The Built-in user cannot be removed. Select the users whose types are not the Built-in. W 00222 106071 The selected users could not be removed.
Table 15 Error codes (part code 00222) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00222 107014 Failed to get the user group information. If the problem persists despite retrying, please contact HP Technical Support. W 00222 107017 An error occurred while accessing the alert information. Try again. If this problem persists, contact HP Technical Support. E 00222 107024 An error occurred during SVP processing.
Table 16 Error codes (part code 00290) (continued) Part Code Error Number Error Message Recommended Action Severity Level • Storage Administrator role (System Resource Management) • Audit log Administrator role (View & Modify) Contact the security administrator, and then register the user to an user group which has a necessary role. 00290 005130 No role (Support personnel). The following role is required for this operation.
Table 16 Error codes (part code 00290) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00290 006140 Failed to open the user account list file. If the same error occurs again despite retrying, please contact HP Technical Support. - 00290 006150 Failed to open the user account list file. If the same error occurs again despite retrying, please contact HP Technical Support. - 00290 006160 Failed to open the user account list file.
Table 16 Error codes (part code 00290) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00290 056111 File name is not specified. Specify the file name, then retry the operation. - 00290 056121 File name is not specified. Specify the file name, then retry the operation. - 00290 056131 File name is not specified. Specify the file name, then retry the operation. - 00290 056141 File name is not specified. Specify the file name, then retry the operation.
Table 16 Error codes (part code 00290) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00290 056791 Failed to delete work files. If this problem persists, please contact HP Technical Support. - 00290 056792 Failed to delete work files. If this problem persists, please contact HP Technical Support. - 00290 059000 The configuration has completed. You need to login again to update these parameters. Reply to this message.
Table 17 Error codes (part code 00305) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00305 007103 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 00305 007110 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 00305 007201 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 18 Error codes (part code 00310) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00310 009060 This item will be deleted. Do you want to continue? - W 00310 065684 Specify a value between 0 to FFFF in each field. Correct the settings, then retry the operation. W 00310 065685 0 cannot be specified in all the fields. Correct the settings, then retry the operation. W 00310 065686 The OS being used does not support IPv6.
Table 19 Error codes (part code 00405) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00405 005073 To install/remove this program product, Install or remove the related program product first. W you must install/remove another program product first.
Table 19 Error codes (part code 00405) (continued) Part Code Error Number Error Message Recommended Action Severity Level • External Storage Access Manager >>>>> Continuous Access Synchronous • Auto LUN >>>>> Performance Monitor • Cont Access Journal 3DC & 4x4 Open MF >>>>> Continuous Access Journal Z • Cont Access Journal 3DC & 4x4 Open MF >>>>> Continuous Access Journal • Hyper Parallel Access Volumes >>>>> Parallel Access Volumes • Smart Tiers >>>>> Thin Provisioning • Thin Provisioning Z >>>>> Thin
Table 19 Error codes (part code 00405) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00405 005079 This program product needs another DKC type. Please contact HP Technical Support. W 00405 005080 You cannot change this program product. Please contact HP Technical Support. W 00405 005501 The trial days have exceeded the specified extended days. Please confirm the installation status of the program product.
Table 19 Error codes (part code 00405) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00405 007205 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 00405 007206 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 00405 007207 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 19 Error codes (part code 00405) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00405 055520 It is not possible to install it because of PP of pre-install. If this problem persists, please contact HP Technical Support. E 00405 056524 This function cannot be used by the storage partition administrator. If the same problem persists despite retrying, please contact HP Technical Support. E 00405 057003 The contents of the license file are incorrect.
Part code 00410 Table 21 Error codes (part code 00410) Part Code Error Number Error Message Recommended Action Severity Level 00410 005030 The displayed information has not been Specify what you register, and retry. changed. Try again. W 00410 055000 Since the error occurred in the Install or Acquire the information again, and retry the Remove judging, the apply operation operation. cannot be performed. W 00410 055001 The length of the key code is incorrect. Check the length of the key code.
Part code 00605 Table 22 Error codes (part code 00605) Part Code Error Number Error Message Recommended Action Severity Level 00605 002011 The status of the storage system requires the maintenance (for example, the storage system is blocked, the shared memory is inconsistent, or some other factor). Check the status of the storage system (if the E storage system is blocked, shared memory is inconsistent, or some other factor). If this problem persists, please contact HP Technical Support.
Table 22 Error codes (part code 00605) (continued) Part Code Error Number Error Message Recommended Action Severity Level Journal, or Continuous Access Journal Z is defined. 00605 002517 A pair of Business Copy, Business Copy Release the pair definition, and then retry the Z, Compatible FlashCopy, Compatible operation. When quick split is in progress, FlashCopy SE, Fast Snap, or Snapshot suspend the pair, and then release it. is defined.
Table 22 Error codes (part code 00605) (continued) Part Code Error Number Error Message Recommended Action Severity Level this setting, but an error in the others settings. 00605 008000 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 00605 008001 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 00605 008102 This function is not supported.
Table 22 Error codes (part code 00605) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00605 058330 After executing the Disconnect External Execute the Reconnect External Storage Systems W Storage Systems or the Disconnect or the Reconnect External Volumes, then retry the External Volumes, neither the Reconnect operation. External Paths nor the Disconnect External Paths can be executed. 00605 058331 The specified External Path is not registered.
Table 22 Error codes (part code 00605) (continued) Part Code Error Message Recommended Action Severity Level 00605 065793 The specified External Path Group has already been used. Clear the duplicated setting, then retry the operation. W 00605 065794 The specified external volume is not mounted. Check the specified external volume. W 00605 065795 The specified external volume has already been specified. Exclude the duplicated setting, then retry the operation.
Table 22 Error codes (part code 00605) (continued) Part Code Error Number Error Message Recommended Action Severity Level Check the setting of SSID. W group within the range grouped by 32 LDEV numbers. 00605 066506 Specified SSID has already been used. 00605 066507 The target external volume is blocked or Check the status and the capacity of target not set within the range of capacity that external volume. can be used. W 00605 066508 The specified LDEV capacity is invalid.
Table 22 Error codes (part code 00605) (continued) Part Code Error Message Recommended Action Severity Level 00605 066713 The value of ExG is not set within the available range. Check the setting of ExG. W 00605 066715 Attribute is invalid. Check the setting of Attribute. W 00605 066718 It is not set within the range where CLPR Check the setting of CLPR. can be used. W 00605 066720 It is not emulation type that can be specified. Check the setting of emulation type.
Table 22 Error codes (part code 00605) (continued) Part Code Error Number Error Message Recommended Action Severity Level volume that includes Pool VOLs registered in the pool that has the association with a normal Thin Provisioning volume. 00605 068742 Set the same cache mode to all the volumes that compose a Pool VOL. If there is a volume whose cache mode cannot W be changed due to its bind mode setting, release the bind mode setting first.
Table 22 Error codes (part code 00605) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00605 078052 The port that is connected to the specified external WWN belongs to a resource group that you do not have permission to access. Log out, and then log back in with access to the resource group containing the port that is connected to the specified external WWN.
Part code 00621 Table 23 Error codes (part code 00621) Part Code Error Number Error Message Recommended Action Severity Level 00621 109214 If you enable the use of internal volume, Disable the setting in general. the local storage system and internal If you want to enable this setting, contact HP volumes are displayed as external Technical Support. storage.
Table 24 Error codes (part code 00622) (continued) Part Code Error Number Error Message Recommended Action 00622 105244 The specified external volume cannot be Check the contents of the path configuration. set because the path configuration is different. W 00622 105245 Failed to allocate a LDEV ID. Check the setting(s). W 00622 105246 Failed to allocate a SSID. Check the setting(s). W 00622 105251 The external volume is not supported.
Table 24 Error codes (part code 00622) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00622 105272 The specified external WWN is used for Log out, and then log back in with access to the an external volume in a resource group resource group containing the external volume that you do not have permission to that uses the specified external WWN. access.
Table 24 Error codes (part code 00622) (continued) Part Code Error Number Error Message Recommended Action 00622 106527 The specified external path group does not exist in the configuration. Refresh the window, and then retry the operation. E If this problem persists, contact HP Technical Support. 00622 106528 The specified WWN does not exist in the configuration. Refresh the window, and then retry the operation. E If this problem persists, contact HP Technical Support.
Part code 00710 Table 25 Error codes (part code 00710) Part Code Error Number Error Message Recommended Action Severity Level 00710 009101 Do you want to cancel? To cancel the operation, click [OK]. Otherwise, click [No]. i 00710 055011 0 cannot be specified in all the fields or Reply to the message. the Class A field. 00710 055030 The displayed information has not been Specify the data to be registered in the SVP, and W changed. Try again. then retry the operation.
Table 26 Error codes (part code 00722) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00722 105430 Invalid characters are used in the specified Location Identification Name. "," and space cannot be used. Check the setting(s). W 00722 105431 The Location Identification Name is not set. Check the setting(s). W 00722 107025 The processing cannot continue due to an internal logic contradiction. Refresh the window, and retry the operation.
3 Messages (part code group 01nnn) This chapter lists the Remote Web Console error messages with part code 01000 to 01999 and provides recommended action for each error. Part code 01005 Table 28 Error codes (part code 01005) Part Code Error Number Error Message Recommended Action Severity Level 01005 001002 The specified volume cannot be set as Select another volume.
Table 28 Error codes (part code 01005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 01005 001021 Invalid host mode. The configuration information has been changed W already. Check the settings, and request the configuration information setting again. 01005 001022 Invalid host mode. The configuration information has been changed W already. Check the settings, and request the configuration information setting again. 01005 001023 Invalid Fibre address.
Table 28 Error codes (part code 01005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 01005 001111 When requesting a configuration change Check the setting(s), then retry the operation. of LUN-Security, a nickname is not specified. Specify the nickname of HOST GROUP. W 01005 001116 When registering WWN, the value is Check the setting(s), then retry the operation. not specified. Or, zero is set as the value of WWN.
Table 28 Error codes (part code 01005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 01005 001180 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 01005 001181 The specified path cannot be added, Correct the specification, then retry the operation. W because the volume is used by a Remote Copy pair.
Table 28 Error codes (part code 01005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 01005 001369 The specified host mode option cannot be set to the initiator port. Verify the host mode option or the attribute of the W port. 01005 001600 This functionality is not available. Open Install the necessary PP license key. System Array Management is required. W 01005 001601 This functionality is not available. Open Install the necessary PP license key.
Table 28 Error codes (part code 01005) (continued) Part Code Error Number Error Message 01005 002010 The LDEV is being used by the host, or Recovery processing may take about 1 minute. an error occurred in the SVP procedure. Wait for a while. W 01005 002013 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. W 01005 002015 An error occurred while connecting to the storage system.
Table 28 Error codes (part code 01005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 01005 005013 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 01005 005099 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 01005 006000 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 28 Error codes (part code 01005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 01005 056302 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 01005 056303 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 01005 057101 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Part code 01022 Table 29 Error codes (part code 01022) Part Code Error Number Error Message Recommended Action Severity Level 01022 105009 All the check boxes are cleared. Check the check boxes for the items that you want W to change, then retry the operation. 01022 105010 The host group name is not set. Enter the host group name from 1 to 64 characters. W 01022 105011 The number of characters specified in the host group name has exceed the maximum.
Table 29 Error codes (part code 01022) (continued) Part Code Error Number Error Message Recommended Action Severity Level same port, or it exists in the [Selected Hosts] table. 01022 105026 The processing cannot be done because Check if there is a target host to be set in the of no data in the [Selected Hosts] table. [Selected Hosts] table. When there is not, add host(s) and retry the operation. When there is, close the window(s) and refresh it, then retry again.
Table 29 Error codes (part code 01022) (continued) Part Code Error Number Error Message Recommended Action Severity Level 01022 105046 HBA WWN cannot be converted into hexadecimal. Specify the HBA WWN with 16 digits in hexadecimal. W 01022 105047 The length of the host name is incorrect. Enter the host name within 1 to 64 characters. W 01022 105048 An invalid character is used in the host name. W 01022 105049 You are trying to register the same host Check the setting(s).
Table 29 Error codes (part code 01022) (continued) Part Code Error Number Error Message 01022 105085 The setting cannot be changed, because Check the setting(s). the value of UUID is outside the range. W 01022 105086 The input value of the starting LUN ID is Check the setting(s). outside the range. W 01022 105087 The LUN ID cannot be set, because the value is outside the range. Check the setting(s). W 01022 105088 The table column is not selected.
Table 29 Error codes (part code 01022) (continued) Part Code Error Number Error Message Recommended Action Severity Level 01022 105277 Some LDEVs or Host Groups that are not Click [OK], then continue the operation. available for LUN path setting are excluded from the choices. W 01022 105296 The specified port belongs to a resource Log out, and then log back in with access to the group that you do not have permission resource group containing the specified port. to access.
Table 29 Error codes (part code 01022) (continued) Part Code Error Number Error Message Recommended Action 01022 106506 The specified LU does not exist in the configuration. Refresh the window, and then retry the operation. E If this problem persists, contact HP Technical Support. 01022 106510 The specified host does not exist in the configuration. Refresh the window, and then retry the operation. E If this problem persists, contact HP Technical Support.
Table 29 Error codes (part code 01022) (continued) Part Code Error Number Error Message Recommended Action Severity Level 01022 108005 There is a volume, which is set as Check the setting(s). reserved by Data Retention, in the target path information. W 01022 108006 The specified LDEV is a reserved volume Check the setting(s). of Data Retention. W 01022 108007 The specified LDEV is set other than the Read/Write (S-VOL enabled) of Data Retention. Check the setting(s).
Table 29 Error codes (part code 01022) (continued) Part Code Error Number Error Message Recommended Action Severity Level 01022 109202 When you switched the host mode Check that UUID is allocated to all LUs set in the W option 33 from Disabled to Enabled, host group, then reboot OpenVMS. access to LU where UUID is not allocated is disabled. 01022 109203 Consecutive LUN IDs could not be assigned from the specified number. However, unused LUN IDs after the specified number were assigned.
Part code 01310 Table 31 Error codes (part code 01310) Part Code Error Number Error Message Recommended Action Severity Level 01310 005832 The user name is incorrect. Correct the settings, then retry the operation. W 01310 005833 The secret is incorrect. Correct the settings, then retry the operation. W 01310 005834 The reentered secret does not match the Correct the settings, then retry the operation. previously entered secret.
Table 31 Error codes (part code 01310) (continued) Part Code Error Number Error Message Recommended Action 01310 069054 No permission to perform this operation. The following role is required for this operation. Severity Level W • Storage Administrator (View Only) Contact the security manager, and register the user to User Group who has a necessary role. 01310 069055 You cannot use multi-byte characters. Remove the multi-byte characters and retry.
4 Messages (part code group 02nnn) This chapter lists the Remote Web Console error messages with part code 02000 to 02999 and provides recommended action for each error. Part code 02005 Table 32 Error codes (part code 02005) Part Code Error Number Error Message Recommended Action Severity Level 02005 001002 The specified volume cannot be set as Select another volume.
Table 32 Error codes (part code 02005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 02005 001137 Error happened before the change was The configuration information has been changed W processed. Failed to form a LUSE volume already. Check the settings, and request the because the number of LUSE volumes configuration information setting again. exceeds the maximum that can be set in a storage system.
Table 32 Error codes (part code 02005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 02005 001925 The combination order of LUSE volume is incorrect. Check the settings. W 02005 001931 The specified volume cannot be operated, because the volume is used as an external volume that is mapped for online data migration. Specify a volume other than the external volume mapped for the online data migration, and then retry the operation.
Table 32 Error codes (part code 02005) (continued) Part Code Error Message Recommended Action Severity Level 02005 005013 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 02005 005877 The setting cannot be done because you All the resource group IDs that are set to the have no access right to the subject storage system must be assigned to the user resource group. account that logs in to Remote Web Console.
Part code 02010 Table 33 Error codes (part code 02010) Part Code Error Number Error Message Recommended Action Severity Level 02010 005030 The LUSE volume cannot be released because the access attribute of the specified volume is not Read/Write. Correct the settings, then retry. W 02010 005032 There are no LDEVs to set the LUSE top volume. Check the specified LDEVs. Correct the specified content, and retry. W 02010 005033 There are no available LDEVs to make the LUSE.
5 Messages (part code group 03nnn) This chapter lists the Remote Web Console error messages with part code 03000 to 03999 and provides recommended action for each error. Part code 03005 Table 34 Error codes (part code 03005) Part Code Error Message Recommended Action Severity Level 03005 001910 The specified volume contains a Snapshot pair or a Fast Snapshot pair. Check the setting of the specified volumes. W 03005 001911 The specified volume contains Pool-VOLs.
Table 34 Error codes (part code 03005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03005 002094 Some pairs of Business Copy, Business Copy Z, Snapshot, or Fast Snap pairs exist. Change the status of the volumes to Simplex. W 03005 002095 The specified operation cannot be performed due to one of the following maintenance operations: Wait for a while, and retry. W • LDEV formatting is in progress. • Correction copy is in progress.
Table 34 Error codes (part code 03005) (continued) Part Code Error Number Error Message Recommended Action Severity Level Journal pair, or a Continuous Access Journal Z pair. 03005 002517 The target volume is defined as a pair volume of Business Copy, Business Copy Z, Snapshot, or Fast Snap. Or, the volume is used in Compatible FlashCopy, Compatible FlashCopy SE, or Compatible XRC. 03005 002518 A pair of Business Copy, Business Copy Split the pair, then retry the operation.
Table 34 Error codes (part code 03005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03005 006050 An error occurred during SVP processing. If nothing changes despite retrying, contact HP Technical Support. E 03005 006533 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 03005 006537 There is an error in another setting and the setting processing has not been executed.
Table 34 Error codes (part code 03005) (continued) Part Code Error Message Recommended Action Severity Level 03005 055512 The specified volume is an external volume. Specify another volume. W 03005 055513 The specified volume is used as a V-VOL. Specify another volume. W 03005 055514 The specified volume is not configured. Specify another volume. W 03005 055516 This function is not available, because the program product is not installed. Install the program product.
Table 34 Error codes (part code 03005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03005 058469 The specified logical volume is being used by another program product. Specify another logical volume. W 03005 058470 The operation cannot be done because Add some Pool-VOL, or decrease the data for the usage of the specified pool is 100% Snapshot or Fast Snap by restoring or deleting (full). the Snapshot or Fast Snap pairs.
Table 34 Error codes (part code 03005) (continued) Part Code Error Number Error Message Recommended Action Severity Level to be maintained is in PSUS status or being restored. 03005 058626 A Snapshot pair or Fast Snap pairs is defined. Cancel the pair definition, and then retry the operation. W 03005 058706 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 34 Error codes (part code 03005) (continued) Part Code Error Number Error Message Recommended Action Severity Level Restore is not in operation, and then retry the operation. 03005 065767 The specified volume contains a quorum Check the specified volume. disk. W 03005 065790 The specified volume includes a remote Check the specified volume. command device being used by a mirror of the journal group. W 03005 068722 The specified volume is not a Thin Provisioning volume.
Table 34 Error codes (part code 03005) (continued) Part Code Error Number 03005 068798 Error Message Recommended Action Severity Level Failed to delete the pool. If the pool cannot be deleted, do the following: W A Pool cannot be deleted when: • Check the installation status of the V-VOL management area when the V-VOL management area is not initialized. • The V-VOL management area is not initialized. • The V-VOL management area is not installed. • A Snapshot pair still remains in the pool.
Table 34 Error codes (part code 03005) (continued) Part Code Error Number 03005 068824 Error Message Recommended Action Severity Level The specified volume is currently used by Continuous Access Synchronous, Continuous Access Synchronous Z, or External Storage Access Manager. Wait until the processing of Continuous Access E Synchronous, Continuous Access Synchronous Z, or External Storage Access Manager is completed, and then retry the operation.
Table 34 Error codes (part code 03005) (continued) Part Code Error Number Error Message Recommended Action Severity Level You cannot expand the V-VOLs for the volumes that are being used in the following program products: Change the setting to not use the volumes of the following program products as a target of expanding V-VOL, and then retry the operation.
Table 34 Error codes (part code 03005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03005 078020 The operation cannot be You cannot stop shrinking pools. Wait until pools W executedperformed, because the are shrunk.Verify the pool status. available period to stop shrinking pools has elapsedpassed. 03005 078024 The encryption key cannot be created, Check the specified encryption key number.
Table 34 Error codes (part code 03005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03005 078040 The storage system is set to the state of suppression of tier relocation starting. Please contact HP Technical Support. E 03005 078041 The operation cannot be executed because the specified pool is now in zero page reclaiming process. Wait until the zero pages are reclaimed and then W retry or cancel the operation.
Table 34 Error codes (part code 03005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03005 078059 A pool volume cannot be set to the specified pool because the number of drive types exceeds the supported number. Check the number of the supported drive types, then retry the operation. W 03005 078060 The multi tier pool cannot be disabled because the RAID level of each tier is different.
Table 34 Error codes (part code 03005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03005 078078 The operation cannot be done because Release the Compatible FlashCopy or Compatible W the specified V-VOL is used in FlashCopy SE setting, and then retry the Compatible FlashCopy or Compatible operation. FlashCopy SE. 03005 078107 An internal volume and an external volume cannot be set as pool VOLs in the specified pool.
Table 34 Error codes (part code 03005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03005 078198 The specified page range is invalid. Specify the start page number and the length of the page range within an available page range of the specified volume. W 03005 078199 The specified page tiering level of the tiering policy is invalid. Verify the specified page tiering level.
Table 34 Error codes (part code 03005) (continued) Part Code Error Number Error Message Recommended Action Severity Level then retry the operation. If this problem persists, contact HP Technical Support. 03005 078298 The specified volume cannot be set as a pool volume. Verify the requirements for the pool volume. W 03005 078305 The operation cannot be performed because the pool volume with a system area is blocked.
Table 36 Error codes (part code 03022) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03022 105141 The selected LDEV has been set as a journal volume. Check the setting(s). W 03022 105142 The selected LDEV has been set as a quorum disk volume. Check the setting(s). W 03022 105143 The selected LDEV has an access attribute setting. Check the setting(s). W 03022 105144 An LDEV whose emulation type is OPEN-L is selected. Check the setting(s).
Table 36 Error codes (part code 03022) (continued) Part Code Error Number Error Message Recommended Action Severity Level of LDEVs that can be set has already reached the maximum. 03022 105167 The specified parity group cannot be set Check the setting(s). because the emulation type is OPEN-L. W 03022 105168 The selected parity group has no LDEV ID to specify. Check the setting(s). W 03022 105169 Data in the table is not selected. Check the setting(s).
Table 36 Error codes (part code 03022) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03022 105191 LDEV that has already been set has been Check the setting(s). selected. E 03022 105192 LDEV not set has been selected. E 03022 105193 The number of data patterns exceeds the Check the setting(s). setting range. W 03022 105194 An error occurred while formatting. Execute refresh, then retry the operation.
Table 36 Error codes (part code 03022) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03022 105279 This functionality is not available. Virtual Check the setting(s). LVI is required. W 03022 105280 This functionality is not available. Open Check the setting(s). Volume Management is required. W 03022 105281 There is no LDEV that can be formatted. Check the setting(s).
Table 36 Error codes (part code 03022) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03022 105440 The parity group to be operated contains Check the setting(s). LDEVs where journal volumes are set. W 03022 105441 The parity group to be operated contains Check the setting(s). LDEVs where quorum disks are set. W 03022 105445 The selected LDEV is an external volume select a different LDEV. that is mapped for online data migration.
Table 36 Error codes (part code 03022) (continued) Part Code Error Number Error Message Recommended Action Severity Level Check the settings. W When TB, GB, or MB is specified as the unit on the window to create LDEVs, and LDEV with a larger capacity than specified may be created due to capacity correction. 03022 105473 Missing %d SSIDs.
Part code 03122 Table 38 Error codes (part code 03122) Part Code Error Number Error Message Recommended Action Severity Level 03122 105264 The password is invalid. Check the password, then retry the operation. W 03121 105483 The specified Tiering Policy cannot be Check the Tiering Policy setting. set due to one of the following reasons: W • The Tier1 Min value exceeds the Tier1 Max value. • The Tier3 Min value exceeds the Tier3 Max value.
Table 38 Error codes (part code 03122) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03122 106018 The specified pool ID is incorrect. Check the specified pool ID, then retry the operation. W 03122 106019 The allocation cannot be done from the Specify a pool ID that is smaller than the one specified pool ID. specified before, then retry the operation.
Table 38 Error codes (part code 03122) (continued) Part Code Error Number Error Message Recommended Action Severity Level delete the pool volume with a system area. 03122 106035 The operation cannot be executed, because the top pool volume has been selected. Select a volume other than the top pool volume. W 03122 106036 The operation cannot be executed, because the specified pool volumes contain an abnormal pool volume. Check the state of the specified pool volumes, then retry the operation.
Table 38 Error codes (part code 03122) (continued) Part Code Error Number Error Message Recommended Action Severity Level types are used together in the same pool, the performance will be impacted by the lowest performing volume types. Confirm that the selected LDEVs with a mix of volume types are OK? 03122 106095 The operation cannot be performed because the tier management of the specified pools is not in manual operation. Change the tier management of the pool to the manual operation.
Table 38 Error codes (part code 03122) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03122 106111 There is an empty field in the following items. Check the settings, and then retry the operation. W Check the settings, and then retry the operation. W • Tier Management • Cycle Time • Monitoring Period • Monitoring Mode • Buffer Space for New page assignment • Buffer Space for Tier relocation 03122 106112 There is no check in the check box of Smart Pool.
Part code 03205 Table 39 Error codes (part code 03205) Part Code Error Number Error Message Recommended Action Severity Level 03205 002011 The status of the storage system requires the maintenance (for example, the storage system is blocked, the shared memory is inconsistent, or some other factor). Check the status of the storage system (if the E storage system is blocked, shared memory is inconsistent, or some other factor). If this problem persists, please contact HP Technical Support.
Table 39 Error codes (part code 03205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03205 005013 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 03205 005099 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 03205 005511 A necessary program product is not installed. Install the necessary program product(s).
Table 39 Error codes (part code 03205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03205 056517 A pair of Business Copy, Business Copy Release the pair definition and then retry the Z, Snapshot, or Fast Snap is defined. operation. W 03205 056519 The reserved volume setting for Business Release the reserved volume setting for Business Copy or Business Copy Z is defined. Copy or Business Copy Z, then retry the operation.
Table 39 Error codes (part code 03205) (continued) Part Code Error Number Error Message Recommended Action Severity Level package for mainframe system is not mounted. 03205 066747 The value of SSID is not set within the available range. Check the value of the specified SSID. W 03205 066748 A value different from SSID that has already been set is specified. Check the setting of SSID.
Table 39 Error codes (part code 03205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03205 078062 The specified values of CU and pool ID Set the values of CU and pool ID to the odd or do not follow the rule to create a volume the even number. of TSE attribute. W 03205 078063 A TSE-VOL cannot be associated with a Specify a pool where the smart pool setting is pool where the smart pool setting is disabled. enabled.
Table 40 Error codes (part code 03222) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03222 105432 The performance of host I/O might Expand the capacity of a virtual volume at the temporarily decrease for the expanded time when the expansion does not affect volume when the capacity of a virtual operations. volume is expanded in a host connection environment. Verify if the system is affected or not.
Table 41 Error codes (part code 03305) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03305 001074 The specified CU number cannot be set. Correct the settings. 03305 001075 In the VLL operation (Create LDEVs, Specify one or more than one operations of E Delete LDEVs), there are some operations Create LDEVs, Delete LDEVs in the VLL operation. which cannot be set together are specified. 03305 001101 An operation is specified for the uninstalled volume.
Table 41 Error codes (part code 03305) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03305 002015 An error occurred while connecting to the storage system. A communication error occurs. If the same error occurs despite retrying, please contact HP Technical Support. E 03305 002022 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 41 Error codes (part code 03305) (continued) Part Code Error Number Error Message Recommended Action Severity Level • The processor status is changing. • The cache status is changing. • LDEV Shredding is in progress. • The configuration is changing. 03305 002200 The Concurrent Copy or the Compatible Cancel the Concurrent Copy job or delete a XRC operation is in progress in the Compatible XRC pair via the host. target volumes.
Table 41 Error codes (part code 03305) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03305 003003 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 03305 003006 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 03305 003008 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 41 Error codes (part code 03305) (continued) Part Code Error Message Recommended Action Severity Level 03305 065740 The configuration changing processes are conflicting at DKC. Check if the configuration changing process by RAID Manager, Auto LUN, or Quick Restore is not in operation, and then retry the operation. W 03305 065741 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 03305 065742 An error occurred during SVP processing.
6 Messages (part code group 04nnn) This chapter lists the Remote Web Console error messages with part code 04000 to 04999 and provides recommended action for each error. Part code 04005 Table 42 Error codes (part code 04005) Part Code Error Number Error Message Recommended Action Severity Level 04005 005010 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 04005 005040 The number of requests exceeds the maximum number that can be processed.
Table 42 Error codes (part code 04005) (continued) Part Code Error Number Error Message Recommended Action Severity Level available number of cache residency areas. CLPR No:%s 04005 055246 The total number of Cache Residency Check the settings, then retry the operation. areas set for the CLPRs and the maximum number of the Cache Residency areas in the storage system are not equal. W 04005 055247 The cache residency size set for the CLPR Check the settings, then retry the operation.
Table 42 Error codes (part code 04005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 04005 056542 The prestaging is not executed because To use the prestaging function, set the prestaging W the prestaging area does not exist. area by using Cache Residency. Check the Cache Residency setting. 04005 058511 The current Cache Residency setting Wait, then retry the operation. cannot be changed because the sidefile size exceeds the threshold.
Table 43 Error codes (part code 04010) (continued) Part Code Error Number Error Message Recommended Action Severity Level cache is smaller than the value specified as the starting address. 04010 005011 The value specified as the Number of Cache Residency areas is equal to or less than one cylinder. Correct the specified content, and retry. W 04010 005030 No deletion area is specified. Retry the operation to specify the deletion area. Correct the specified content, and retry.
7 Messages (part code group 05nnn) This chapter lists the Remote Web Console error messages with part code 05000 to 05999 and provides recommended action for each error. Part code 05105 Table 44 Error codes (part code 05105) Part Code Error Number Error Message Recommended Action Severity Level 05105 002002 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 05105 002003 An error occurred during SVP processing.
Table 44 Error codes (part code 05105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05105 006092 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 05105 006501 There is no monitoring data. Change the monitor switch to ON, and accumulate the data. W 05105 007007 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Part code 05107 Table 45 Error codes (part code 05107) Part Code Error Number Error Message Recommended Action Severity Level 05107 005099 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 05107 006012 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 47 Error codes (part code 05121) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05121 109206 The monitored CUs will be deleted. Do you want to continue? To continue, click [OK]. Otherwise, click [Cancel]. W 05121 109207 The monitored WWNs will be deleted. Do you want to continue? To continue, click [OK]. Otherwise, click [Cancel].
Table 48 Error codes (part code 05122) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05122 105116 A WWN to be monitored cannot be Reduce the number of WWNs to be monitored added, because the number of graph to 32 or fewer per port. display objects per one port exceeds the maximum. W 05122 105226 The Graph Display Term cannot be changed, because there is no graph data. Click [OK]. W 05122 105227 The HBA WWN is unedited. Edit the HBA WWN.
Part code 05205 Table 49 Error codes (part code 05205) Part Code Error Number Error Message Recommended Action Severity Level 05205 001076 The specified volume(s) are already used Specify another volume. by Business Copy Z or Business Copy. 05205 001077 The specified volume(s) are already used The volume used by Business Copy Z, or Business W by Business Copy Z or Business Copy. Copy cannot be used. Specify another volume. 05205 001078 The volume is a LUSE volume. Cannot change to reserve volume.
Table 49 Error codes (part code 05205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05205 001096 The command has been rejected, Execute the vary offline command to disable the because the volume specified as a target volume from the mainframe host, then retry the volume or a reserved volume is used by operation. the host. W 05205 001109 Auto LUN does not support the volume(s). Retry the same operation. If nothing changes, please contact HP Technical Support.
Table 49 Error codes (part code 05205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05205 001215 The volume specified as a migration source is a command device. The command device cannot be used for Auto LUN. Specify another volume. W 05205 001216 The target volume(s) is not equipped. Retry the same operation. If nothing changes, please contact HP Technical Support. W 05205 001217 The command was rejected due to one of the following reasons.
Table 49 Error codes (part code 05205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05205 001232 The specified volume(s) are already used Specify another volume. by Business Copy Z or Business Copy. W 05205 001233 The specified volume(s) are already used Specify another volume. by Business Copy Z or Business Copy. W 05205 001234 The volume specified as a migration Specify another volume.
Table 49 Error codes (part code 05205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05205 001611 The specified volume has Read Only/Protect/S-VOL Disable setting of Data Retention. Release the Read Only/Protect/S-VOL Disable setting of Data Retention. W 05205 001612 The specified volume has Read Only/Protect/S-VOL Disable setting of Data Retention. Release the Read Only/Protect/S-VOL Disable setting of Data Retention.
Table 49 Error codes (part code 05205) (continued) Part Code Error Number 05205 005506 Error Message Recommended Action Severity Level The specified volume cannot be migrated For the relation between Continuous Access W because it is used as P-VOL in the Synchronous, Continuous Access Synchronous Z, following status.
Table 49 Error codes (part code 05205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05205 007401 Failed to get information from Retry the same operation several times. If the same E hihsmpln.ini. The file may not exist in the error occurs, please contact HP Technical Support. specified directory. 05205 007402 Failed to get information from hihsmfpg.ini. The file may not exist in the specified directory.
Table 49 Error codes (part code 05205) (continued) Part Code Error Number 05205 007420 Error Message Recommended Action Severity Level There is insufficient Auto LUN data to create migration plans. Check the following: Retry the same operation several times. If the same W error occurs, please contact HP Technical Support. • The time setting for the sampling term • The monitoring term 05205 007421 A proper migration plan cannot be made by this function. Check the following items.
Table 49 Error codes (part code 05205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05205 055060 The specified volume migration plan cannot be executed because a volume on which VMA of Data Retention is set is paired with a volume on which VMA is not set. Confirm the settings of the specified volumes.
Table 49 Error codes (part code 05205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05205 055522 The specified volume(s) are already being used as V-VOL(s). Select another volume. W 05205 055523 The specified volume(s) are already being used as Pool-VOL(s). Select another volume. W 05205 055524 The specified volumes are already used Specify a different volume. as the volumes of Snapshot or Fast Snap.
Table 49 Error codes (part code 05205) (continued) Part Code Error Number 05205 055600 Error Message Recommended Action Severity Level The specified volume is used as a volume of Delta resync for Continuous Access Journal or Continuous Access Journal Z. The volume of Delta resync cannot be specified as a reserved volume. W See "Supported and prohibited source and target volumes" in the HP P9000 Performance for Open and Mainframe Systems User Guide.
Table 49 Error codes (part code 05205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05205 065700 The volume specified as a migration source cannot be used, because it is being used by FICON(R) Data Migration. Specify another volume. W 05205 065701 The volume specified as a migration target cannot be used, because it is being used by FICON(R) Data Migration. Specify another volume.
Table 49 Error codes (part code 05205) (continued) Part Code Error Message Recommended Action Severity Level 05205 065738 The volume specified as a migration target cannot be used, because it is a volume of Thin Provisioning in capacity expanding. Confirm the capacity of the volume specified as a migration target after the capacity expanding operation is completed. W 05205 065739 The specified volume cannot be used, because it is a volume of Thin Provisioning whose capacity is being added.
Table 49 Error codes (part code 05205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05205 075018 The volume specified as a migration source cannot be used because its emulation type is 3390-V. Specify another volume. W 05205 075019 The volume specified as a migration target cannot be used because its emulation type is 3390-V. Specify another volume.
Table 49 Error codes (part code 05205) (continued) Part Code Error Message Recommended Action Severity Level 05205 076503 The specified LDEV belongs to a resource group that you do not have permission to access. Log out, and then log back in with access to the resource group containing the specified LDEV. W 05205 076504 The specified LDEV belongs to a resource group that you do not have permission to access.
Part code 05210 Table 50 Error codes (part code 05210) Part Code Error Number Error Message Recommended Action Severity Level 05210 005010 There is no monitoring data. Change the monitor switch to ON, and accumulate the data. i 05210 009060 The plan will be deleted. Do you want to continue? To continue processing, click [OK]. To stop processing, click [Cancel]. W 05210 009061 The specified instructions will be reset. Do you want to continue? To continue processing, click [OK].
Table 51 Error codes (part code 05305) (continued) Part Code Error Message Recommended Action Severity Level 05305 002002 An error occurred during SVP processing. Failed to connect the communication between DKCs (SVPs). If the same error occurs despite retrying, please contact HP Technical Support. E 05305 002015 A connection error has occurred. Retry the same operation. If the same error occurs W despite retrying, please contact HP Technical Support.
Table 51 Error codes (part code 05305) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05305 006000 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 05305 006012 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 05305 006022 File open error occurred. If the same error occurs despite retrying, please contact HP Technical Support.
Table 51 Error codes (part code 05305) (continued) Part Code Error Number Error Message Recommended Action Severity Level If this problem persists, please contact HP Technical Support. 05305 056524 This function cannot be used by the storage partition administrator. Select another window. If you want to set this E function, please contact the storage administrator.
Table 51 Error codes (part code 05305) (continued) Part Code Error Number 05305 058576 Error Message Recommended Action Severity Level A communication time-out error occurred The error may be caused by a temporary E in the storage system. communication failure. Reboot the SVP or click [Refresh All] on the File menu of Remote Web Console and refresh the configuration information to recover from the error. If this problem persists, please contact HP Technical Support.
Table 53 Error codes (part code 05310) (continued) Part Code Error Number Error Message Recommended Action Severity Level Please specify the WWN with 16 characters, using any of the following in combination: • Numerals (0 - 9), • Letters (A - F), • Hyphen (-), or • Space. (You cannot specify 0 for all the 16 characters.) 05310 005067 The maximum value is not set for the non-priority port. Set the maximum value for the non-priority port.
Table 53 Error codes (part code 05310) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05310 007427 Configuration information is not correct. If the problem persists despite retrying, please contact HP Technical Support. E 05310 009077 Are you sure you want to delete the WWN? To continue processing, click [OK]. To stop processing, click [Cancel].
8 Messages (part code group 06nnn) This chapter lists the Remote Web Console error messages with part code 06000 to 06999 and provides recommended action for each error. Part code 06005 Table 54 Error codes (part code 06005) Part Code Error Number Error Message Recommended Action Severity Level 06005 005013 An error occurred during SVP processing. If the problem persists despite retrying, please contact HP Technical Support. E 06005 005099 An error occurred during SVP processing.
Table 54 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06005 008704 The specified number of paths is less Check the paths status and reestablish the paths. W than the minimum number of paths on the RCU option screen due to a communication error between the MCU and the RCU.
Table 54 Error codes (part code 06005) (continued) Part Code Error Number 06005 008720 Error Message Recommended Action The operation failed because the number Reduce the number of RCUs, and then retry the of RCUs is in one of the following status: operation. Severity Level W • Maximum 4 RCUs are already registered in one CU. • Maximum 64 RCUs are already registered while CU FREE is selected. 06005 008721 Path not completely established.
Table 54 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level use Continuous Access Synchronous, please contact HP Technical Support. 06005 008739 NVS status of MCU is not active. The MCU NVS status specified by the host is not W active. Set the NVS to "on" for the MCU, using any attached host, then retry the operation. 06005 008740 NVS status of RCU is not active. The RCU NVS status specified by the host is not active.
Table 54 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06005 008749 Specified R-VOL is still online from HOST. Check if the input number of R-VOL is correct. If W not, enter the correct R-VOL number. If the number is correct, vary the specified path offline. 06005 008751 Remote Copy is not supported under the Confirm the RCU controller emulation type. RCU controller emulation type. W 06005 008753 An internal error occurred.
Table 54 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06005 008768 The RCU is still in another Remote Copy The RCU containing the R-VOL is being used as condition. the RCU for Continuous Access Synchronous. Verify the status of the RCU, if necessary delete the RCU, then retry the operation. W 06005 008769 The RCU is still in another Remote Copy The RCU containing the R-VOL is being used as condition.
Table 54 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06005 008789 Combination of the M-VOL and R-VOL configuration is not valid. Verify the configuration of both M-VOL and R-VOL. W 06005 008790 The specified expansion volume (Port/GID/LUN) of the RCU is not usable. Confirm the status of the specified expansion volume and microcode version of the RCU. W 06005 008791 The specified M-VOL is still online from another HOST.
Table 54 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06005 008798 The MCU is already used for Business Copy Z/Business Copy/Compatible FlashCopy. Confirm the status of Business Copy Z/Business Copy/Compatible FlashCopy in MCU from the host or the SVP. W 06005 008799 The M-VOL is already in use for Auto LUN. Verify the status of the specified M-VOL. W 06005 008800 The R-VOL is already in use for Auto LUN.
Table 54 Error codes (part code 06005) (continued) Part Code Error Number 06005 008822 Error Message Recommended Action Severity Level The operation cannot be performed due Verify that the volume is in usable condition. If it W to one of the following reasons: is usable, verify that the microcode version of the • An I/O error occurred in the R-VOL. MCU supports this function or configuration. If the microcode version supports this function or • The R-VOL is in unusable condition.
Table 54 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06005 008842 R-VOL status change failed after M-VOL Confirm the R-VOL status. status change. Confirm R-VOL status. W 06005 008843 Suspend (Pairsplit-r) operation failed because specified volume or other volume in the same group is not in permissible status. W The operation failed, because of one of the following reasons: • The specified volume is simplex.
Table 54 Error codes (part code 06005) (continued) Part Code Error Number 06005 008855 Error Message Recommended Action Severity Level Delete(Pairsplit-S) operation failed because specified volume or other volume in the same group is in status transition. The operation failed, because of one of the following reasons: W • The status of the specified volume or another volume in the same group is Deleting. • The status of the specified volume or another volume in the same group is Suspending.
Table 54 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06005 008890 The specified port is being initialized. Wait for a while, then retry the operation. W 06005 008891 Logical paths exist on the MCU port. Delete the LUs defined on the specified port, then W retry the operation. 06005 008892 R-VOLs exist on the RCU port. Are you If you want to continue this operation, click [Yes].
Table 54 Error codes (part code 06005) (continued) Part Code Error Message Recommended Action Severity Level 06005 008907 The extended SM is not equipped in RCU. Install the extended shared memory to RCU according to the installation instruction of the extended shared memory for remote copy ("Shared Memory Size Configuration" dialog box). E 06005 008908 Invalid parameter. Specify a correct value. W 06005 008909 A Port exchange error occurred.
Table 54 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06005 008936 The Paircreate operation failed. The version of the specified RCU does not support Remote Copy with the NAS volume. Check the microcode version of the RCU. W 06005 008939 The specified M-VOL cannot be used. Check the LUN of the specified M-VOL by using RAID Manager, and specify the LUN with the value less than 1,024 for the M-VOL.
Table 54 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06005 008980 The operation failed because the licensed capacity of Mainframe Array Management on the RCU side was exceeded. Confirm the licensed capacity Mainframe Array W Management on the RCU side. To execute this operation, purchase a license key that allows you to use a larger capacity. 06005 008982 You cannot create a pair, because the specified M-VOL is a command device.
Table 54 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level status of the Continuous Access Journal becomes "PAIR," then retry the operation. • When the RCU runs on the configuration other than the 2DC configuration in which the Continuous Access Journal cooperates, specify another volume for R-VOL, then retry the operation. If the Pairresync operation failed, resume the Continuous Access Journal pair volume first.
Table 54 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level Access Journal Z pair using a mirror ID other than 0, and retry the operation. 06005 058494 A pair cannot be created because the specified M-VOL is being used by Fast Snap or Snapshot. Select a different volume. W W 06005 058495 A pair cannot be created because the specified R-VOL is being used by Fast Snap or Snapshot. Select a different volume.
Table 54 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06005 065740 The configuration changing processes are conflicting at DKC. Check if the configuration changing process by the RAID Manager, the Auto LUN, or the Quick Restore is not in operation, and then retry the operation. W 06005 068011 The operation failed because the specified M-VOL was used as a Thin Provisioning volume.
Table 54 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06005 68790 The Paircreate operation failed because Install the External Storage Access Manager the External Storage Access Manager function to the RCU. function was not installed in the RCU. W 06005 068791 The operation failed because the specified volume was not an R-VOL. Refresh the window, and confirm whether the specified volume is an R-VOL.
Table 54 Error codes (part code 06005) (continued) Part Code Error Number 06005 068827 Error Message Recommended Action Severity Level The operation failed, because there was • The serial number of the local DKC cannot be W an error in the specified parameter. set as the serial number of the other DKC. Check the input serial number of the other DKC. • A quorum disk cannot be registered in a same external storage device with a different quorum disk ID.
Table 54 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06005 068876 The operation failed, because the parity Select a parity group of an external volume that group of the specified external volume is composed of a single LDEV. was composed of two or more LDEVs. E 06005 068877 The operation failed, because the Select another volume, or release the Business specified volume was a reserved volume Copy setting. of Business Copy.
Table 54 Error codes (part code 06005) (continued) Part Code Error Number 06005 068895 Error Message Recommended Action Severity Level The operation failed, because of one of Confirm the program product of the specified following reasons. pair. W • Specified the other program product for the pair of Continuous Access Synchronous. • Specified the other program product for the pair of External Storage Access Manager.
Table 54 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06005 078129 The operation failed because the Specify a volume other than the external volume specified P-VOL was an external volume that was mapped for online data migration. that was mapped for online data migration.
Part code 06010 Table 56 Error codes (part code 06010) Part Code Error Number Error Message Recommended Action Severity Level 06010 005010 The Priority value is invalid. Specify the correct value. Correct the specified contents, and retry. W 06010 005011 The Range value is invalid. Specify the correct value. Correct the specified contents, and retry. W 06010 005012 The Error Level value is invalid. Specify the correct value. Correct the specified contents, and retry.
Table 56 Error codes (part code 06010) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06010 007302 An error occurred in the client logic. Please contact HP Technical Support. E 06010 007303 An error occurred in the client logic. Please contact HP Technical Support. E 06010 007440 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. If this problem persists, please contact HP Technical Support.
Table 56 Error codes (part code 06010) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06010 009075 Are you sure you want to delete the SSIDs of a specified RCU? To delete the specified SSID, click [OK]. Otherwise, click [Cancel]. W 06010 009100 Do you want to exit? To close the window, click [OK]. Otherwise, click i [Cancel]. 06010 009101 Do you want to cancel? To cancel, click [OK].
Table 56 Error codes (part code 06010) (continued) Part Code Error Number Error Message 06010 009124 This process may take up to %d minutes. To continue the operation, click [OK]. To cancel Do you want to continue? the operation, click [Cancel]. 06010 009125 Are you sure you want to cancel the export? To stop the operation, click [OK]. To continue the W operation, click [Cancel]. 06010 009126 The script is running now.
Table 56 Error codes (part code 06010) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06010 009311 All SSIDs which you set have already been registered. This operation will terminate because there is no SSID which can be added. Since all the added SSIDs are overlapped, the operation of adding SSIDs cannot be executed. Click [OK], and continue.
Table 56 Error codes (part code 06010) (continued) Part Code Error Number Error Message Recommended Action 06010 059013 The specified file already exists. Do you To overwrite the file, click [Yes]. Otherwise, click want to overwrite this file? [No]. W 06010 059026 The specified RCU has been already set. Check the RCU parameter settings. Check the RCU parameter settings. W 06010 059030 The monitoring data saved at present will be deleted. W To continue the operation, click [OK].
Table 56 Error codes (part code 06010) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06010 065804 The quorum disk ID was not specified. Specify the quorum disk ID, then retry the When the [Change attribute to ESAM] operation. parameter has been changed from [No] to [Yes], specify the quorum disk ID. W 06010 069018 There are two or more LDKC numbers Check the LDKC number for the specified data for the specified data volume.
Table 56 Error codes (part code 06010) (continued) Part Code Error Number Error Message Recommended Action Severity Level Error Message Recommended Action Severity Level 06505 003003 An error occurred during SVP processing. If the problem persists despite retrying, please contact HP Technical Support. E 06505 005013 An error occurred during SVP processing. Retry the operation. If this problem persists, please E contact HP Technical Support. 06505 005040 Too many objects are specified.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 008002 A communication time-out error occurred Wait a while, then retry the operation. in the storage system. Please wait for a while, and then retry the operation. 06505 008100 An error occurred during SVP processing. Retry the operation. If this problem persists, please E contact HP Technical Support. 06505 008102 This function is not supported.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 008714 An internal error occurred. Please contact HP Technical Support. E 06505 008715 The number of paths is incorrect. Ensure that the number of paths is correct, then W retry the operation. If the problem persists, please contact HP Technical Support.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 008731 The existing logical addresses are not the same. Delete the DKC once, then add the DKC using the same logical address. W 06505 008733 Continuous Access Journal or Continuous Continuous Access Journal or Continuous Access W Access Journal Z is not installed in the Journal Z must be installed in the storage system storage system.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level hosts or the SVP, is in any of the following conditions: • The secondary data volume is being used by Dual Copy. • The secondary data volume is being used by XRC Replication. • The secondary data volume is being used by PPRC or Remote Copy. • The secondary data volume is being used by Concurrent Copy. • The access attribute of the secondary data volume is Read Only.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number 06505 008795 Error Message Recommended Action Severity Level The operation failed because the volume Check the status of the primary data volume from W specified as the primary data volume is the host or the SVP. used by Business Copy or Business Copy Z and in one of the following statuses: • The volume is a Business Copy S-VOL and not in the PSUS status. • The volume is a Business Copy Z T-VOL and not in the Split status.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 008832 Please wait a few minutes and then retry Wait a few minutes and retry the operation. the operation. W 06505 008833 Wait a few minutes, then retry the operation. Wait for a few minutes and retry the operation. W 06505 008834 The Add Pair (Paircreate) operation failed because you tried to create volume pairs which exceeded the licensed capacity.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level attempt was rejected because the same operation was in progress from a host. 06505 008922 The primary storage system does not support remote copy function via the serial interface. Check whether the primary storage system W supports remote copy via serial interface. Install the microcode that supports remote copy via serial interface, or execute remote copy via fibre interface.
Table 57 Error codes (part code 06505) (continued) Part Code Error Message Recommended Action Severity Level 06505 056535 Processing in progress. Please wait for a while, and then retry the operation. Processing in progress. Wait a while, then retry the operation. W 06505 058005 Too many requests. Please reduce the number of requests to be processed at one time. After that, please retry the operation. Reduce the number of requests to be processed at one time. Then retry the operation.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 058027 The specified threshold for ending creation of synchronous journal is invalid. Check the threshold for ending creation of synchronous journal. W 06505 058028 The specified threshold for starting creation of asynchronous journal is invalid. Check the threshold for starting creation of asynchronous journal.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 058070 Invalid parameter (Suspend Condition-Master Journal Failure). Check the specified Suspend Condition parameter. W 06505 058071 Invalid parameter (Suspend Condition-Restore Journal Failure). Check the specified Suspend Condition parameter. W 06505 058072 The pair status has not changed yet.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number 06505 058088 Error Message Recommended Action Severity Level The specified mirror ID differs from the registered mirror ID. Check the specified mirror ID. W Check the combination of the master journal and the mirror ID. 06505 058089 No more remote storage systems can be Reduce the number of registered remote storage registered. systems, then retry the operation.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 058103 The volume specified as the secondary data volume is a reserved volume of a mainframe host. Check the status of the volume specified as the W secondary data volume from the mainframe host. 06505 058104 The volume specified as the secondary data volume is already used by Compatible XRC.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number 06505 058271 Error Message Recommended Action Severity Level The volume specified as the secondary Verify the following items on the Data Retention W data volume cannot be used due to one window if the volume specified as the secondary of the following reasons: data volume is an open-system volume. • "S-VOL Disable" is set by Data Retention. • Whether "S-VOL Disable" is set to the specified secondary data volume.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 058282 The specified secondary data volume is Identify the journal where the specified secondary W already registered in another journal. data volume is registered. 06505 058283 The specified secondary data volume Identify the journal where the specified secondary W cannot be deleted, because the volume data volume is registered. is already registered in another journal.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level • Thin Provisioning • Business Copy Z 06505 058297 The volume specified as the primary Verify if the volume specified as the primary data W data volume is being used by a different volume is being used by any of the following program product.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level Continuous Access Synchronous Z and Business Copy or Business Copy Z. 06505 058327 The Paircreate operation failed because Select a different volume, and then retry the the volume specified as the primary data operation. volume is a LUSE volume.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 058343 The specified volume cannot be used as Check the setting of the specified volume in the a journal volume because of a Volume Volume Security window. Security setting.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level • A P-VOL of Business Copy used in conjunction with External Storage Access Manager. • An S-VOL of Business Copy Z or Compatible FlashCopy used in conjunction with Continuous Access Synchronous Z. • A volume used by Flex Copy XP. • A Thin Provisioning volume used as a P-VOL of Business Copy. • A Thin Provisioning volume and a source volume of Auto LUN.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 058457 Continuous Access Synchronous, Specify a mirror ID other than 0, then retry the External Storage Access Manager, or operation. Continuous Access Synchronous Z is using the specified primary data volume. Specify a mirror ID other than 0 if you use this volume to create a pair.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action of the secondary storage system does not support VMA of Data Retention. Technical Support to confirm whether the Continuous Access Journal function supports Data Retention VMA. 06505 058502 The operation failed because the volume capacity of the secondary storage system has exceeded the licensed capacity of Open Systems Array Management.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 058553 The specified volume cannot be used as Check whether the specified volume is used by a journal volume because it is used by Parallel Access Volumes. Parallel Access Volumes. W 06505 058560 A journal volume cannot be added Please contact HP Technical Support to install because the capacity of shared memory additional shared memory. is insufficient.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 058594 The Paircreate operation failed because Check the LUSE volume configuration of the the configuration of the LUSE volume primary data volume and the secondary data was different between the primary data volume. volume and the secondary data volume.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level Check if the specified journal belongs to an extended consistency group (EXCTG). W primary storage system does not support the EXCTG function. 06505 058609 The timer type cannot be changed, because the specified journal belongs to an extended consistency group (EXCTG). 06505 058610 The parameter specified in the extended Refresh the window, then retry the operation.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 058625 Journals cannot be added to the Check if the specified journal is being used by extended consistency group (EXCTG), other program product you are using. because the specified journals are being used by another program product. W 06505 058627 The specified operation failed because Check the status of the command device.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 058686 The specified operation failed, because Check the attribute of the journal of the remote the attribute of the journal of the remote storage system. storage system was not "restore." W 06505 058687 The status of the other mirror of the Delta If the problem persists despite retrying, contact resync did not change. HP Technical Support.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number 06505 058695 Error Message Recommended Action Severity Level No more journals can be allocated to the specified command device. Delete the journal registered in the extended consistency group (EXCTG), then retry the operation with another command device. W Delete the journals registered in the extended consistency group (EXCTG), then retry the operation with another command device.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level data volume for Continuous Access Journal are different. • The M-VOL for Continuous Access Synchronous Z and the primary data volume for Continuous Access Journal Z are different. 06505 058705 The Delta resync operation failed. The Check the status of the specified secondary data W specified secondary data volume should volume. meet the following requirements.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number 06505 058719 Error Message Recommended Action The related program products are: The related program products are: • Continuous Access Synchronous or Continuous Access Synchronous Z • Continuous Access Synchronous or Continuous Access Synchronous Z • Continuous Access Journal or Continuous Access Journal Z • Continuous Access Journal or Continuous Access Journal Z The licensed capacity of Continuous Access Synchronous or Con
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 066594 The number of digits of LDEV (P-VOL) is invalid. Check the contents of the spreadsheet. W 06505 066595 The format of LDEV (P-VOL) is invalid. Check the contents of the spreadsheet. W 06505 066596 The value entered as LDEV (P-VOL) is outside the setting range. Check the contents of the spreadsheet.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 066619 The value entered as LDKC (paired VOL) Check the contents of the spreadsheet. is outside the setting range. W 06505 066620 The value of LDKC (paired VOL) is not supported. Check the contents of the spreadsheet. W 06505 066621 The number of digits of CU (paired VOL) Check the contents of the spreadsheet. is invalid.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 066645 The number of digits of PathGroup is invalid. Check the contents of the spreadsheet. W 06505 066646 The format of PathGroup is invalid. Check the contents of the spreadsheet. W 06505 066647 The value entered as PathGroup is outside the setting range. Check the contents of the spreadsheet. W 06505 066648 The number of digits of ResyncMode is invalid.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 066671 The value entered as SuspendMode is outside the setting range. Check the contents of the spreadsheet. W 06505 066672 The number of digits of CFW is invalid. Check the contents of the spreadsheet. W 06505 066673 The format of CFW is invalid. Check the contents of the spreadsheet.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 068008 The Add Pair (Paircreate) operation failed because the capacity of shared memory of the primary storage system was insufficient. Check the capacity of shared memory of the primary storage system. E 06505 068009 The Add Pair (Paircreate) operation failed because the capacity of shared memory of the remote storage system was insufficient.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level function is not installed in the secondary storage system. 06505 068028 Journals cannot be added to the extended consistency group(EXCTG), because the current microcode version does not support LDKC numbers other than 0. Confirm the LDKC number of the specified extended consistency group. W 06505 068759 The status of the specified volume is Simplex or SMPL.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 068804 The operation failed because the specified M-VOL is used as FICON(R) Data Migration. Check the status of the specified M-VOL from the W host or the SVP. 06505 068805 The operation failed because the specified R-VOL is used as FICON(R) Data Migration or Data Migration. Check the status of the specified R-VOL from the host or the SVP.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action 06505 068852 The operation failed, because the specified consistency (CT) group or the secondary data volume was being shared with multiple primary and secondary storage systems. This CT group or the secondary data volume cannot be used for Delta resync. Check whether the specified CT group or the W secondary data volume was shared with multiple primary and secondary storage systems or not.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level • It was a pair of synchronous consistency group. • It was a pair that the "Cylinder" was set to "Difference Management." 06505 068888 The operation failed, because the Confirm the relationship status of the Compatible W specified "primary data volume" was FlashCopy. used as T-VOL of Compatible FlashCopy that might be in the abnormal state due to a failure.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level was not installed in the master storage system. 06505 068913 The operation failed because the Cont Access Journal 3DC & 4x4 Open MF was not installed in the restore storage system. Verify if the Cont Access Journal 3DC & 4x4 W Open MF is installed in the restore storage system or not.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level Access Journal or Continuous Access Journal Z 3DC cascading configuration is Active. 06505 068925 The operation to create a pair for Delta Verify the primary data volume. resync failed because the pair status of the specified primary data volume was not PAIR.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 078140 The Add Pair (Paircreate) operation failed because the specified P-VOL was used as an external volume that was mapped for online data migration. Specify a volume other than the external volume mapped for the online data migration, and then retry the operation.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number 06505 078274 Error Message Recommended Action Severity Level The Paircreate operation failed because Verify the microcode version of the primary W the primary storage system is one of the storage system and the models of the primary and following: the secondary storage systems. • The microcode version does not support the connection with the secondary storage system.
Table 57 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 078296 The Add Pair (Paircreate) operation failed because there is not enough space left in the difference management area of the secondary storage system. If the extended shared memory is not installed in W the secondary storage system, install it, and then retry the operation.
Part code 06510 Table 59 Error codes (part code 06510) Part Code Error Number Error Message Recommended Action Severity Level 06510 005030 The displayed information has not been Specify the data that you want to register in the changed. Try again. SVP, and retry the operation. W 06510 005137 The Operation value is invalid. Specify the correct value. Check the contents, and retry. W 06510 005138 The value specified for Gathering Interval is invalid.
Table 59 Error codes (part code 06510) (continued) Part Code Error Number Error Message Recommended Action Severity Level change the channel cable connections is displayed, and then perform the necessary changes. 06510 009100 Do you want to exit? To close the window, click [OK]. Otherwise, click i [Cancel]. 06510 009101 Do you want to cancel? To cancel the operation, click [OK]. 06510 009102 Do you want to apply? To apply settings in Preview to the storage system, i click [OK].
Table 59 Error codes (part code 06510) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06510 009155 The history file has been updated. Select Click [OK]. the OK button to display the history logs from the beginning. i 06510 009303 There are no valid volumes. Check the device emulation or the definition of the SCSI path. W 06510 009305 There are no initiator ports. Set the port to Initiator before registering the storage system.
Table 59 Error codes (part code 06510) (continued) Part Code Error Number Error Message Recommended Action Severity Level Specify "Mirror" as the range when you want to delete pairs forcibly. 06510 055644 [Warning] To delete pairs, click [Yes]. Otherwise, click [No]. W There are some pairs where "Mirror" is not specified as the range in the pairs specified to be deleted forcibly. These pairs and other pairs in the same mirror may be suspended due to failure by this operation.
Table 59 Error codes (part code 06510) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06510 059030 The monitoring data saved at present will be deleted. To continue the operation, click [OK]. To cancel the operation, click [Cancel]. W The current monitoring data will be deleted if you change the setting of the monitoring switch. If necessary, use the Performance Monitor Export Tool to export the monitoring data file.
Table 59 Error codes (part code 06510) (continued) Part Code Error Number Error Message Recommended Action 06510 059153 The journal volume cannot be deleted, because the mirror status of the journal is Active. Change the mirror status of the journal to Stop or W Initial, then retry the operation. 06510 059321 No more journals can be added to the specified extended consistency group (EXCTG). Check the number of journals in the specified extended consistency group (EXCTG).
Table 59 Error codes (part code 06510) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06510 065777 The current microcode version of DKCMAIN cannot assign remote command devices to mirrors. The microcode versions between the DKCMAIN and the SVP might not match. Confirm the microcode versions of the DKCMAIN and the SVP. W 06510 065778 No more remote command devices can Check if a remote command device was assigned W be assigned to the specified mirror.
Table 59 Error codes (part code 06510) (continued) Part Code Error Number Error Message Recommended Action Severity Level Check whether the specified volume is a LUSE volume. Also, check storage system's microcode version. W operation, please specify only one LDKC number. 06510 069019 The number of data volumes exceeds the maximum. 06510 069021 Journals cannot be added to the Check the number of registered EXCTG.
Table 60 Error codes (part code 06610) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06610 009008 SIMs of Continuous Access Journal and Click [OK]. Continuous Access Journal Z are cleared. i 06610 009009 The export is complete. i 06610 009021 The Port Setting process has not To continue processing, click [Yes]. If the completed. Do you want to continue for processing finishes, reconfigure the port that is other ports? not in operation.
Table 60 Error codes (part code 06610) (continued) Part Code Error Number Error Message Recommended Action 06610 009116 Another operator has changed the Click [OK]. Gathering Interval value. The graph will be closed. i 06610 009117 Are you sure you want to close the graph? To close the graph, click [OK]. Otherwise, click [Cancel]. W 06610 009118 Please check the specified value. To apply this setting, click [OK]. To change the setting, click [Cancel].
Table 60 Error codes (part code 06610) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06610 055038 Too many mirrors in the storage system. Check the number of mirrors in the journal group, W then delete unused mirrors. 06610 055039 You are specifying "Mirror" for the Check the range setting. If you specify "Mirror," range and trying to manipulate the same select only one data volume pair in the mirror. mirror.
Table 60 Error codes (part code 06610) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06610 059007 Are you sure you want to delete the specified storage systems? To delete the specified storage system, click [OK]. W Otherwise, click [Cancel]. 06610 059008 Are you sure you want to delete the paths of the specified storage system? To delete the specified path, click [OK]. Otherwise, click [Cancel]. 06610 059009 Since the number of preview data Click [OK].
Table 60 Error codes (part code 06610) (continued) Part Code Error Number Error Message Recommended Action 06610 059042 There are no valid journals. All journals are used by Universal Replicator for W z/OS or Continuous Access Journal. If possible, delete the journals for Universal Replicator for z/OS or Continuous Access Journal, then start the Universal Replicator for z/OS window or the Continuous Access Journal window.
Table 60 Error codes (part code 06610) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06610 059153 The journal volume cannot be deleted, because the mirror status of the journal is Active. Change the mirror status of the journal to Stop or W Initial, then retry the operation. 06610 059321 No more journals can be added to the specified extended consistency group (EXCTG). Check the number of journals in the specified extended consistency group (EXCTG).
Table 60 Error codes (part code 06610) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06610 065663 The specified LDKC number is incorrect. Specify the correct LDKC number. Specify the correct LDKC number. W 06610 065664 The specified volume is not valid for this Specify another volume. program product. Specify another volume. W 06610 065665 The specified volume is not the volume to be monitored. Check the monitoring setting. Check the monitoring setting.
Table 60 Error codes (part code 06610) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06610 069016 Are you sure you want to cancel the export? To stop the operation, click [OK]. i Check the number of registered journals. To continue the operation, click [Cancel]. 06610 069017 No more journals can be registered, because the number of registered journals has reached the maximum.
Table 61 Error codes (part code 06805) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06805 008001 A communication time-out error occurred Retry the operation. If the same problem persists in the storage system. Please wait for a despite retrying, please contact HP Technical while, and then retry the operation. Support. W 06805 008002 Communication is busy. W 06805 008110 The configuration could not be changed. Please contact HP Technical Support.
Table 61 Error codes (part code 06805) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06805 055221 The CLPR number is duplicated. Correct the setting, then retry. If the same problem W persists despite retrying, please contact HP Technical Support. 06805 056524 This function cannot be used by the storage partition administrator. Please contact HP Technical Support.
9 Messages (part code group 07nnn) This chapter lists the Remote Web Console error messages with part code 07000 to 07999 and provides recommended action for each error. Part code 07005 Table 63 Error codes (part code 07005) Part Code Error Number Error Message Recommended Action Severity Level 07005 005013 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 07005 005099 An error occurred during SVP processing.
Table 63 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07005 008501 The command has been rejected, Wait a while, and retry the operation. because the command specified last time is being processed. W 07005 008502 You cannot reserve the volume, because Delete the Remote Copy pair. a remote copy pair exists in the same storage system frame. W 07005 008503 You cannot create the new pair, because Delete the Remote Copy pair.
Table 63 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07005 008519 Volumes specified as P-VOL and S-VOL, Select volumes with the same capacity. or those constituting LUSE are not When specifying LUSE volumes as P-VOL and consistent in capacity. S-VOL, the capacity of each volume constituting the LUSE volumes must be the same. W 07005 008520 You cannot set a pair, because the volume type is different for each.
Table 63 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07005 008542 Failed to complete the initial shared memory setup. Please contact HP Technical Support. E 07005 008543 The shared memory size is different. Please contact HP Technical Support. E 07005 008544 16 Mbytes of shared memory is available. - i 07005 008545 A power supply failure is detected. Please contact HP Technical Support.
Table 63 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07005 008563 The volume type is invalid. Check the contents, and retry. W 07005 008564 The volume type is invalid. Check the contents, and retry. W 07005 008565 The command code sender is invalid. Please contact HP Technical Support. E 07005 008566 The attribute of the reserved volume is invalid. Please contact HP Technical Support.
Table 63 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07005 008587 The number of pairs that can be set in the same group is invalid. Check the contents, and retry. W 07005 008588 The specified group number is not set. Check the contents, and retry. W 07005 008589 The specified group name is invalid. Check the contents, and retry. W 07005 008590 The group name and the number do not Check the contents, and retry. match.
Table 63 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action Severity Level See the section about the sharing Business Copy volumes in the Business Copy User Guide for the relation between the state of Continuous Access Synchronous pair or External Storage Access Manager pair and the Business Copy operations. 07005 008608 The specified S-VOL is not defined. Refresh the window, and retry the operation.
Table 63 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07005 008626 The SMPL command was rejected, because the high-speed Split was in progress. After the high-speed Split is completed, retry the operation. W 07005 008627 The Pairresync operation has been rejected, because pair status is COPY(SP)/COPY. Wait until the status of the pair changes to PSUS.
Table 63 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action Severity Level between the state of pairs and the Business Copy operations. 07005 008644 The operation failed because the pairs Verify the status of the pairs that share the P-VOL. W sharing a P-VOL contain a pair in other than PSUS or PSUE status. 07005 008645 The Reverse Copy command was Release the remote copy pair, then retry the rejected because the P-VOL was shared operation.
Table 63 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07005 008920 Because a L1 pair is not PSUS, you cannot execute operations for L2 pair. Wait until L1 pair becomes PSUS status, then execute the operation for L2 pair. W 07005 055264 The command was rejected because you You cannot create a pair with these volumes.
Table 63 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action Severity Level The command has been rejected, because the specified P-VOL is used as P-VOL of Continuous Access Synchronous pair or External Storage Access Manager pair. The requested command cannot be executed in the current status of Continuous Access Synchronous pair or External Storage Access Manager pair.
Table 63 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action 07005 058478 The operation cannot be performed, because the specified P-VOL is a pool volume. Release the pool volume or select another volume. W 07005 058479 The operation cannot be performed because the specified S-VOL is a P-VOL for Fast Snap or Snapshot. Release either the Fast Snap pair or the Snapshot W pair, or select another volume.
Table 63 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07005 058576 A communication time-out error occurred If the problem persists despite retrying, please in the storage system. contact HP Technical Support. E 07005 058579 The operation failed, because the Confirm that the shredding has completed in the W specified volume is being shredded by Data Retention window, then retry the operation. Data Retention.
Table 63 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07005 068738 The command has been rejected, Associate the Thin Provisioning volume with a because the specified S-VOL is a Thin pool, then retry the operation. Provisioning volume not associated with a pool. W 07005 068739 The command has been rejected, because the specified reserved volume is a Thin Provisioning volume not associated with a pool.
Table 63 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07005 068837 The command has been rejected, Wait until the zero page reclamation is because the specified P-VOL is a volume completed, and then retry the operation. of Thin Provisioning whose zero page is being reclaimed.
Table 63 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action Severity Level operation for this volume failed due to one of the following reasons. • The specified volume was used by Delta resync of Continuous Access Journal. • The specified volume was used by a data volume of Continuous Access Journal. 07005 075002 The command was rejected, because the Thin Provisioning volume specified as P-VOL was not associated with a pool.
Table 63 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action Severity Level Wait until the initialization of the pool is completed, and then retry the operation. W Provisioning volume that is specified as the S-VOL was being initialized. 07005 078110 The command was rejected, because the pool associated with the Thin Provisioning volume that is specified as the reserved volume was being initialized.
Table 63 Error codes (part code 07005) (continued) Part Code Error Number 07005 078149 Error Message Recommended Action Severity Level An error occurred during Fast Snap or Snapshot operations due to one of the following reasons: Perform one of the following, and then retry the operation: W • Specify the correct LDEV number. • The LDEV number specified for the • Change the status of the specified pair, or primary volume or secondary volume specify a different pair. is wrong.
Table 63 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07005 078158 The operation cannot be performed because the Fast Snap or Snapshot primary volume is also a Continuous Access Journal secondary volume. Select a different volume. W 07005 078159 The operation cannot be done because Verify the setting of the specified volume. VMA is set for the specified primary volume.
Table 63 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action 07005 078173 The specified secondary volume is Specify another volume. defined as a reserved volume of Business Copy. 07005 078174 The Fast Snap or Snapshot pair cannot be created due to one of the following reasons: Severity Level W Install additional shared memory, or wait until the W initializing process is complete and then retry the operation.
Table 63 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07005 078184 The operation cannot be performed because the Fast Snap or Snapshot primary volume and the Business Copy secondary volume share the same volume, and the Business Copy pair status is not PSUS. Change the status of the Business Copy pair to PSUS, and then retry the operation.
Table 63 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07005 078196 The command was rejected because the Specify a volume other than the external volume secondary volume is used as an external mapped for the online data migration, and then volume that is mapped for online data retry the operation. migration. W 07005 078201 The operation failed because the specified pool is not a Fast Snap pool or a Snapshot pool.
Table 63 Error codes (part code 07005) (continued) Part Code Error Number 07005 078259 Error Message Recommended Action The operation failed because the specified P-VOL that uses two mirrors in 3DC cascade, 3DC multi target, or Delta resync configuration is in one of the following statuses. The operation cannot be performed in the current W pair status of Continuous Access Journal.
Part code 07007 Table 64 Error codes (part code 07007) Part Code Error Number Error Message Recommended Action Severity Level 07007 006012 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 07007 007111 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 65 Error codes (part code 07010) (continued) Part Code Error Number Error Message Recommended Action 07010 007311 The settings could not be applied. Wait a while, and retry the operation. If the same W error occurs despite retrying, please contact HP Technical Support. 07010 007312 The password could not be acquired. Please contact HP Technical Support. E 07010 007313 Error details not available. Please contact HP Technical Support.
Table 65 Error codes (part code 07010) (continued) Part Code Error Number Error Message Recommended Action Severity Level Do you want to continue this operation? 07010 066102 Information was updated by other users. Click [OK], then continue the operation. The list will scroll to the top. W 07010 066560 The maximum number of Pairs or Volumes that can be displayed in the Preview List is 16,384. Change the number of pairs or volumes that is displayed in the Preview List to 16,384 or less.
Table 66 Error codes (part code 07105) (continued) Part Code Error Number Error Message Recommended Action 07105 008502 You cannot reserve the volume, because Delete the Remote Copy pair. a remote copy pair exists in the same storage system frame. W 07105 008503 You cannot create the new pair, because Delete the Remote Copy pair. a remote copy pair exists in the same storage system frame. W 07105 008504 The command was rejected.
Table 66 Error codes (part code 07105) (continued) Part Code Error Number Error Message Recommended Action Severity Level sure that the specified emulation type is the same for both. 07105 008519 You cannot set a pair because the Check the volume capacity. number of cylinders is different for each. W 07105 008520 You cannot set a pair, because the volume type is different for each. Specify the volume with the same emulation type, W and retry the operation.
Table 66 Error codes (part code 07105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07105 008541 There is sufficient shared memory to create 4096 pairs, and the initial storage system setup is complete. Close the message box. i 07105 008542 Failed to complete the initial shared memory setup. Please contact HP Technical Support. E 07105 008543 The shared memory size is different. Please contact HP Technical Support.
Table 66 Error codes (part code 07105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07105 008561 The command code is invalid. Please contact HP Technical Support. E 07105 008562 The command code sender is invalid. If this problem persists please contact HP Technical Support. E 07105 008563 The volume type is invalid. Please contact HP Technical Support. W 07105 008564 The volume type is invalid. Please contact HP Technical Support.
Table 66 Error codes (part code 07105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07105 008585 The number of reserved volumes exceeds Stop the operation of the Reserve volume setting, W the maximum. or delete the Reserve volume. 07105 008586 The number of groups that can be set in Check the contents, and retry. the same storage system is invalid. W 07105 008587 The number of pairs that can be set in the same group is invalid.
Table 66 Error codes (part code 07105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07105 008607 The command has been rejected, because the specified T-VOL is used as M-VOL of Continuous Access Synchronous Z pair. The requested command cannot be executed in the current status of Continuous Access Synchronous Z pair.
Table 66 Error codes (part code 07105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07105 008625 The P-VOL(S-VOL) and S-VOL(T-VOL) have the same number. Check the specified volume number. W 07105 008626 The Simplex command was rejected, because the high-speed Split was in progress. After the high-speed Split is completed, retry the operation. W 07105 008627 The Resync Pairs operation has been rejected, because pair status is SP-Pend/TRANS.
Table 66 Error codes (part code 07105) (continued) Part Code Error Number Error Message Recommended Action Severity Level contain a pair in other than Split/SUSPOP or Suspend/SUSPER status. 07105 008645 The Reverse Copy command has been rejected, because the S-VOL (Primary Volume) is shared as the M-VOL of a Remote Copy pair. 07105 008646 The Reverse Copy request was rejected, Delete the Remote Copy pair.
Table 66 Error codes (part code 07105) (continued) Part Code Error Number Error Message Recommended Action Severity Level a Compatible FlashCopy pair or a Compatible FlashCopy SE pair. 07105 008698 The command has been rejected, because the specified volume is being used as the volume of a Compatible FlashCopy pair or a Compatible FlashCopy SE pair. Delete the Compatible FlashCopy pair or W Compatible FlashCopy SE pair, or specify another volume.
Table 66 Error codes (part code 07105) (continued) Part Code Error Number Error Message 07105 058000 The command has been rejected Select a different volume or release the because the cascade request for creating consistency group setting. cascade pairs composed of volumes belonging to the same consistency group was issued. 07105 058001 The Add Pair (Create Pairs) command Wait until the L1 pair status changes to Split, then W for adding the L2 pair has been rejected retry the operation.
Table 66 Error codes (part code 07105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07105 058301 The reserve volume setting failed because the specified volume was a data volume of Continuous Access Journal Z. Release the Continuous Access Journal Z setting, W or specify another volume. 07105 058351 The Quick Restore command has been rejected because the specified pair contains external volumes, and also is used as a Continuous Access Journal Z pair.
Table 66 Error codes (part code 07105) (continued) Part Code Error Number Error Message Recommended Action Severity Level Access Journal Z pair and the Business Copy Z operations. 07105 058631 The operation failed because the The P-VOL of Continuous Access Journal Z pair specified T-VOL (Secondary Volume) was for Delta resync cannot be specified as S-VOL. used by Delta resync of Continuous Specify another volume. Access Journal Z.
Table 66 Error codes (part code 07105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07105 068769 The SI Operation for FICON(R) Data Migration failed, because the pair status of the specified pair was not Suspend(Mig.). The SI Operation for FICON(R) Data Migration cannot be executed in the current pair status. Change the status of the pair to Suspend(Mig.), then retry the operation.
Table 66 Error codes (part code 07105) (continued) Part Code Error Number Error Message Recommended Action Severity Level Access Manager pair is created by using Thin Provisioning volumes. 07105 068832 The command was rejected because the Use a different consistency group, or release the W specified consistency group is used by pair of Fast Snap or Snapshot, which is using the Fast Snap or Snapshot. specified consistency group.
Table 66 Error codes (part code 07105) (continued) Part Code Error Number Error Message Recommended Action Severity Level as a reserved volume was not associated with a pool. 07105 075015 The specified LDEV belongs to a resource group that you do not have permission to access. Log out, and then log back in with access to the resource group containing the specified LDEV. W 07105 078069 The operation failed because the emulation type of the specified S-VOL (Primary Volume) was 3390-V.
Table 66 Error codes (part code 07105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07105 078121 The operation failed because the specified S-VOL (Primary Volume) was used by Compatible FlashCopy SE, or was a TSE volume. Specify another volume. W 07105 078122 The operation failed because the Specify another volume. specified T-VOL (Secondary Volume) was a TSE volume.
Table 67 Error codes (part code 07110) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07110 008534 An internal logic contradiction occurred. Please contact HP Technical Support. E 07110 008568 The emulation type is invalid. Specify the volume of supported emulation type. i 07110 008658 Some settings could not be applied normally. Refer to the error code. Check the error code in Preview list. W 07110 008659 There is no volume.
Table 67 Error codes (part code 07110) (continued) Part Code Error Number Error Message Recommended Action Severity Level processing. Do you want to switch the LDKC? 07110 065729 Pairs cannot be created any more because SI Operation for FICON(R) Data Migration is already registered to the specified volume. 07110 066102 Information was updated by other users. Click [OK], then continue the operation. The list will scroll to the top.
10 Messages (part code group 08nnn) This chapter lists the Remote Web Console error messages with part code 08000 to 08999 and provides recommended action for each error. Part code 08005 Table 68 Error codes (part code 08005) Part Code Error Number Error Message Recommended Action Severity Level 08005 002002 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 08005 002015 A communication error has occurred. Retry the same operation.
Table 68 Error codes (part code 08005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 08005 007111 The storage system is in the internal Wait, then click [Refresh]. process, or some other user is changing the configuration. E 08005 008001 An error occurred while connecting to the storage system. Wait, then retry the operation. E An error occurred while connecting to the storage system. Wait, then retry the operation.
Table 68 Error codes (part code 08005) (continued) Part Code Error Number 08005 068762 Error Message Recommended Action Severity Level This functionality is not available. Install the required program product. W Encryption License Key is required. 08005 068766 The serial number of the encryption key Use the correct encryption key. does not match.
Table 69 Error codes (part code 08105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 08105 001022 Invalid host mode. The configuration information has been changed W already. Check the settings, and request the configuration information setting again. 08105 001023 The specified fiber address is wrong. Correct the specified content, and issue the W request again. (Currently, Bad Value Send report in Set Response.
Table 69 Error codes (part code 08105) (continued) Part Code Error Number Error Message Recommended Action Severity Level You cannot use spaces for the first and the last characters in the name. 08105 001111 When requesting a configuration change Check the setting(s), then retry the operation. of LUN-Security, a nickname is not specified. Specify the nickname of HOST GROUP. W 08105 001116 When registering WWN, the value is Check the setting(s), then retry the operation. not specified.
Table 69 Error codes (part code 08105) (continued) Part Code Error Number Error Message 08105 001135 When setting the port information (Fibre Check the setting(s), then retry the operation. Address/Fibre Topology/Channel Speed), multiple change instructions are set to the same port. 08105 001138 The same setting is specified at LUNM operation 08105 001140 Because the Port Group setting is done, Release the Port Group setting. it is impossible to change.
Table 69 Error codes (part code 08105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 08105 001600 The error happened before the change was processed. This functionality is not available. Open System Array Management is required. Install the necessary program product licence key. W 08105 001601 The error happened before the change was processed. This functionality is not available. Open System Array Management is required.
Table 69 Error codes (part code 08105) (continued) Part Code Error Number Error Message Recommended Action groups cannot be done because the virtual mode of at least one of the resource groups is on. by specifying resources in the same resource group. Severity Level 08105 002003 An error occurred during SVP processing. Use the SVP to check if the DKC is in the normal status, then retry. If the same problem persists despite retrying, please contact HP Technical Support.
Table 69 Error codes (part code 08105) (continued) Part Code Error Number Error Message Recommended Action Severity Level Please release the pair definition or delete command devices defined by BC Manager, and then retry the operation. 08105 002516 A Remote Copy, Continuous Access Cancel or suspend the pair definition, then retry Journal, or Continuous Access Journal Z the operation. pair is defined. Cancel or suspend the pair definition, and then retry the operation.
Table 69 Error codes (part code 08105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 08105 005650 The length of the letter string is invalid. One line can have up to 127 letters. W 08105 005651 The number of lines is invalid. The spreadsheet can have up to 70,000 lines. W 08105 005652 The size of the CSV file is invalid. Check the CSV file. W 08105 005660 The Thin Provisioning volume is not associated with a pool.
Table 69 Error codes (part code 08105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 08105 005752 The group name does not exist. Correct the group name. W 08105 005753 There is a difference between the current Correct the port ID and the group ID. port ID/group ID and the specified one. W 08105 005754 The intermediate volume cannot be specified as a command device. Correct the CU and LDEV. W 08105 005755 The security switch on the port remains off.
Table 69 Error codes (part code 08105) (continued) Part Code Error Number Error Message Recommended Action 08105 006524 The port information is inconsistent with Correct the port information or the PCB mode PCB mode information. information. W 08105 007060 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 08105 007111 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Part code 08110 Table 71 Error codes (part code 08110) Part Code Error Number Error Message Recommended Action Severity Level 08110 005001 Starting file transfer client. Wait about three minutes, then retry. W 08110 005002 Inaccurate data was acquired. The acquired data is inaccurate. If this problem persists, please contact HP Technical Support. W 08110 005003 Failed to get the data. Retry the operation. W 08110 005004 The first tag is invalid. Correct the first tag.
Part code 08210 Table 72 Error codes (part code 08210) Part Code Error Number Error Message Recommended Action 08210 007440 An error occurred during processing. If If this problem persists, contact HP Technical this problem persists, please contact HP Support. Technical Support. Severity Level E Part code 08222 Table 73 Error codes (part code 08222) Part Code Error Number Error Message Recommended Action Severity Level 08222 105001 The form of Storage System Name is wrong.
Table 75 Error codes (part code 08505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 08505 006024 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 08505 007110 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 08505 008001 A communication time-out error occurred. If this problem persists, please contact HP Technical Support to reboot the SVP PC.
Table 75 Error codes (part code 08505) (continued) Part Code Error Number Error Message Recommended Action 08505 055021 The specified CU number is invalid. Specify the correct CU number, then retry the W operation. If this problem persists, please contact HP Technical Support. 08505 055022 An attempt has been made to either register newly a CLPR that is already registered, or delete a CLPR that is not registered. Correct the CLPR settings, then retry the operation.
Table 75 Error codes (part code 08505) (continued) Part Code Error Number Error Message Recommended Action Severity Level the information of the SLPR that the user owns. SLPR No:%s 08505 056536 The licensed capacity was exceeded because the configuration is changed. Correct the licensed capacity on the License Key Partition Definition panel. W 08505 057002 An unknown error was detected. If this problem persists, please contact HP Technical Support.
Table 75 Error codes (part code 08505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 08505 075015 The specified LDEV belongs to a resource group that you do not have permission to access. Log out, and then log back in with access to the resource group containing the specified LDEV. W 08505 075026 The specified parity group cannot be used because the user has no access right to a resource group to which the parity group belongs.
Table 77 Error codes (part code 08510) (continued) Part Code Error Number Error Message Recommended Action Severity Level 08510 055238 Some of the selected ports cannot Please contact HP Technical Support. migrate to the other SLPR. Please change the settings. E 08510 055240 Some of the selected parity groups Please contact HP Technical Support. cannot migrate to the other SLPR. Please change the settings. E 08510 055261 The concatenated parity group cannot be set across multiple CLPRs.
Table 77 Error codes (part code 08510) (continued) Part Code Error Number Error Message Recommended Action Severity Level 08510 079002 Notice from Partition Definition: Click [OK]. i The capacity of CLPR might not reach the recommended value. Set the CLPR capacity with the recommended value. W Performance may be affected by this setup. If the capacity reaches the recommended value, continue the processing.
Part code 08610 Table 79 Error codes (part code 08610) Part Code Error Number Error Message Recommended Action Severity Level 08610 065758 The field of account or password is left blank. Enter your account or password. W Enter the sender's e-mail address. W Enter a destination e-mail address. W When the SMTP authentication is enabled, your account and password are required to input. 08610 065759 The field of sender's e-mail address is left blank.
Part code 08805 Table 80 Error codes (part code 08805) Part Code Error Number Error Message Recommended Action Severity Level 08805 005010 An error occurred during SVP processing. If the problem persists despite retrying, please contact HP Technical Support. E 08805 005013 An error occurred during SVP processing. If the problem persists despite retrying, please contact HP Technical Support. E 08805 005018 No more report can be made. Delete unnecessary reports, then retry the operation.
11 Messages (part code group 09nnn) This chapter lists the Remote Web Console error messages with part code 09000 to 09999 and provides recommended action for each error. Part code 09005 Table 82 Error codes (part code 09005) Part Code Error Number Error Message Recommended Action Severity Level 09005 005013 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 09005 005040 The number of requests exceeds the maximum number that can be processed.
Table 82 Error codes (part code 09005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 09005 008100 An error occurred while connecting to the storage system. If the problem persists despite retrying, please contact HP Technical Support. E 09005 008102 This function is not supported. Check the DKC-MAIN version. W 09005 008103 Unexpected error occurred. Please refresh the array configuration. The storage system status is invalid. Check the DKC-MAIN version.
Table 84 Error codes (part code 09010) (continued) Part Code Error Number Error Message Recommended Action Severity Level 09010 065703 The maximum permissible capacity of Install additional license key(s) to expand the program product became insufficient. license capacity of this software title. Please install additional license key(s) to expand the license capacity of this software title. W 09010 079003 The used capacity is being calculated now.
Table 85 Error codes (part code 09105) (continued) Part Code Error Number Error Message Recommended Action 09105 006012 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. An error occurred during the SVP processing. If E this problem persists, please contact HP Technical Support. 09105 006023 The file operation failed. Please contact HP Technical Support. E 09105 007060 An error occurred during SVP processing.
Table 85 Error codes (part code 09105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 09105 075055 The operation cannot be performed Specify ports defined in the same resource group. W because there is a port that has been If this problem persists, contact HP Technical set to a different resource group in the Support. specified host group. 09105 075056 The specified security group belongs to a resource group that you do not have permission to access.
Table 87 Error codes (part code 09110) (continued) Part Code Error Number Error Message 09110 005616 Some attributes of the security group are Click [OK], check attributes of the security group, W invalid. and retry the operation. 09110 005617 Attributes of the security group differ from the attributes of other related security groups. 09110 005618 The target logical device has already Click [OK], check the current settings, and retry been defined to another security group. the operation.
Table 87 Error codes (part code 09110) (continued) Part Code Error Number Error Message Recommended Action Severity Level 09110 009083 The specified group is registered in the security group. Are you sure you want to delete the group? To delete the group, click [Yes]. Otherwise, click [No]. i 09110 009084 The specified group includes some hosts. To delete the group, click [Yes]. Otherwise, click Are you sure you want to delete the [No].
Table 88 Error codes (part code 09205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 09205 006023 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. Try again. If this problem persists, contact HP Technical Support. E 09205 006038 The mistake is found in the set parameter. Try again. If this problem persists, contact HP Technical Support. E 09205 006502 Processing in progress.
Table 88 Error codes (part code 09205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 09205 008141 This logical volume cannot be selected because it is used as a reserve volume for Auto LUN. Check the volume, then retry the operation. W 09205 008142 You cannot select this logical volume because it is used as a Continuous Access Journal Z volume. Check the logical volume, then retry the operation.
Table 88 Error codes (part code 09205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 09205 066013 The access attribute set in the [Attribute] Enter a correct attribute in the [Attribute] of the of the spreadsheet is incorrect (an spreadsheet (enter Read/Write, Read Only, or attribute other than Read/Write, Read Protect). Only, or Protect is entered). W 09205 068002 This logical volume cannot be selected because it is used as a volume for System Disk.
Table 90 Error codes (part code 09605) (continued) Part Code Error Number Error Message Recommended Action Severity Level 09605 006012 An error occurred during SVP processing. Try again. If this problem persists, contact HP Technical Support. E 09605 006023 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. Try again. If this problem persists, contact HP Technical Support. E 09605 006038 The mistake is found in the set parameter. Try again.
Table 90 Error codes (part code 09605) (continued) Part Code Error Number Error Message Recommended Action 09605 008135 This logical volume is already used as an S-VOL for Remote Copy or Business Copy. Check the logical volume configuration, then retry W the operation. 09605 008136 The command was rejected, because the licensed capacity was exceeded. The currently licensed capacity is insufficient. To W increase the licensed capacity, buy a new license key.
Table 90 Error codes (part code 09605) (continued) Part Code Error Number Error Message Recommended Action Severity Level 09605 058422 An error occurred during SVP processing. Try again. If this problem persists, contact HP Technical Support. E 09605 058423 An error occurred during SVP processing. Try again. If this problem persists, contact HP Technical Support. E 09605 058424 The specified logical volume is blocked. Restore the logical volume.
Part code 09610 Table 91 Error codes (part code 09610) Part Code Error Number Error Message Recommended Action Severity Level 09610 007060 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. If this problem persists, please contact HP Technical Support. E 09610 007442 There is an invalid value in the Data Retention information. If this problem persists, please contact HP Technical Support. W 09610 008112 There is no valid volume.
12 Messages (part code group 10nnn) This chapter lists the Remote Web Console error messages with part code 10000 to 10999 and provides recommended action for each error. Part code 10010 Table 92 Error codes (part code 10010) Part Code Error Number Error Message Recommended Action Severity Level 10010 055011 0 cannot be specified in all the fields or the Class A field. Reply to the message. W 10010 055638 The same IP address, user ID and Reply to the message.
Part code 10122 Table 94 Error codes (part code 10122) Part Code Error Number Error Message Recommended Action Severity Level 10122 105194 An error occurred while formatting. If the problem persists despite retrying, please contact HP Technical Support. E 10122 105195 An error occurred while preparing the Retry the operation. If the same problem persists E quick format. despite retrying, please contact HP Technical Support.
Table 94 Error codes (part code 10122) (continued) Part Code Error Number Error Message Recommended Action Severity Level 10122 105471 There are no encryption keys already created. Verify the configuration of the encryption keys. W 10122 105480 The total of input values exceeds the maximum. Set the total of input values under the maximum.
Table 94 Error codes (part code 10122) (continued) Part Code Error Number Error Message Recommended Action Severity Level 10122 109028 Creating encryption keys should be limited to 30 in the case of necessity for updating those keys. Be sure to back up after completing the task. To continue, click [OK]. Otherwise, click [Cancel]. W 10122 109029 Be sure to back up after completing the Click [OK]. task.
Table 95 Error codes (part code 10126) (continued) Part Code Error Number Error Message Recommended Action Severity Level 10126 105008 The key wrapping key information of the specified encryption key is damaged. The specified encryption key cannot be used. Specify another backed up encryption key. E 10126 105009 The specified encryption key was not found in the key management server. Verify the specified encryption key.
Table 95 Error codes (part code 10126) (continued) Part Code Error Number Error Message 10126 105015 The deletion operation of the Verify the list of keys that are backed up in the encryption key stopped because the key management server. processing result could not be obtained when deleting the key wrapping key of the specified encryption key from the key management server. 10126 105016 The "Setup Key Management Server" is not configured. Configure the "Setup Key Management Server.
13 Messages (part code group 20nnn) This chapter lists the Remote Web Console error messages with part code 20000 to 20999 and provides recommended action for each error. Part code 20020 Table 96 Error codes (part code 20020) Part Code Error Number Error Message Recommended Action Severity Level 20020 107000 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 20020 107001 An error occurred during SVP processing.
Table 96 Error codes (part code 20020) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20020 107020 A file or a directory of the specified path Check the environment of file or directory of the does not exist, or the access is rejected. specified path. E 20020 107021 A file or a directory of the specified path Check the environment of file or directory of the does not exist, or the access is rejected. specified path.
Table 96 Error codes (part code 20020) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20020 107042 Failed to start the session due to no user Confirm whether you are authorized. authority. E 20020 107043 Failed to save the specific information of user. Check the environment. E 20020 107044 Failed to save the specific information of user. Check the environment. E 20020 107045 Failed to save the specific information of user. Check the environment.
Table 96 Error codes (part code 20020) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20020 107061 Failed to access the key store file. Check the environment. E 20020 107062 Failed to initialize the key store file. Check the environment. E 20020 107063 Failed to access the key store file. Check the environment. E 20020 107064 Failed to get a certificate. Check the environment. E 20020 107065 The key store file does not exist. Check the environment.
Table 96 Error codes (part code 20020) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20020 107096 The specified group ID does not exist. Check the environment. E 20020 107097 Failed to store the user information. Check the environment. E 20020 107098 The user information of the specified onetime key does not exist. Check the environment. E 20020 107099 Failed to get the user information from the specified onetime key. Check the environment.
Table 97 Error codes (part code 20121) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20121 107026 An internal logic error occurred. If the same problem persists despite retrying, please contact HP Technical Support. E 20121 107027 Login failed. The cause might be one of the following. E • The number of user connections reaches the upper limit. • SVP is in preparation. Wait for a while, and then retry.
Table 97 Error codes (part code 20121) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20121 109007 Storage system operations may be To continue, click [OK]. Otherwise, click [Cancel]. W affected significantly if you forcibly unlock the locks. Before unlocking the locks, contact the administrators for the storage system and confirm that the locks can be forcibly unlocked.
Table 98 Error codes (part code 20122) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20122 105477 The entered password is outside the setting range. Set a password within the range shown on the password window. W 20122 105478 The entered password does not meet the Set a password with the password policy shown password policy. on the password window. W 20122 105479 Failed to write in the password policy file. Retry the operation.
Table 98 Error codes (part code 20122) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20122 107019 An internal logic error occurred. If this problem persists, please contact HP Technical Support. E 20122 108029 Remote Web Console cannot be used because there is no license of Remote Web Console. Check the state of installed licenses on the license W window. To use Remote Web Console, set the license of Remote Web Console to the installed state.
Part code 20123 Table 99 Error codes (part code 20123) Part Code Error Number Error Message Recommended Action Severity Level 20123 107000 An internal logic error occurred. If the problem persists despite retrying, please contact HP Technical Support. E 20123 107001 An internal logic error occurred. If the problem persists despite retrying, please contact HP Technical Support. E 20123 107002 An internal logic error occurred.
Table 99 Error codes (part code 20123) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20123 107016 A network error occurred. It is not Check the internet protocol (IP) address. If the IP possible to connect with the SVP due to address is correct, terminate the browser (also one of the following reasons. terminate the storage list browser), then log it in again. • The SVP was not ready. E • An error occurred in the SVP.
Table 99 Error codes (part code 20123) (continued) Part Code Error Number Error Message Recommended Action Severity Level your network does not have any problem, and this problem persists, please contact HP Technical Support. 20123 108000 An internal logic error occurred. If the problem persists despite retrying, please contact HP Technical Support. E 20123 108001 An internal logic error occurred. If the problem persists despite retrying, please contact HP Technical Support.
Table 100 Error codes (part code 20222) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20222 109004 %s is not executed (%s displays the task name). i 20222 109005 %s is in progress (%s displays the task name). - i 20222 109006 %s is completed (%s displays the task name). - i 20222 109007 An error occurred during %s (%s displays the task name). Check the error details displayed in the message E window.
Table 101 Error codes (part code 20305) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20305 008100 An error occurred while connecting to the storage system. If the same problem persists despite retrying, please contact HP Technical Support. E 20305 076500 The specified MP Blade is not mounted. Check the specified MP Blade. W 20305 076501 The specified MP Blade has been blockaded. W 20305 078000 The specified MP Blade is not mounted.
Part code 20520 Table 104 Error codes (part code 20520) Part Code Error Number Error Message Recommended Action Severity Level 20520 107001 Failed to create a report. Check the environment. E 20520 107002 Failed to create a report. Check the environment. E 20520 107003 Failed to create a report. Check the environment. E 20520 107004 Failed to read the log preference. Check the environment. E 20520 107005 The parameter is specified incorrectly. Specify a correct value.
Table 105 Error codes (part code 20522) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20522 105282 A report cannot be created any more Delete unnecessary reports, then retry the because the number of reports that can operation. be created has reached the maximum. W 20522 105310 You do not have permission to access the specified report. Log out, and then log back in with access to the report or with Storage Administrator (Initial Configuration) access.
Table 106 Error codes (part code 20525) (continued) Part Code Error Number 20525 107016 Error Message Recommended Action Severity Level The specified report cannot be downloaded. Display a list of reports and verify if the specified W report is the one you created or not. When you download a report created by another user, you need to have permission to download it. 20525 107017 There is no deletable report. Display a list of reports and verify if there is any of reports that you created.
Table 108 Error codes (part code 20705) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20705 006012 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 20705 006022 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 20705 006533 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 108 Error codes (part code 20705) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20705 076112 The specified parity group is not mounted. Check the specified parity group ID. W 20705 076113 The specified resource is already used. Release the duplicated settings, and then retry the W operation. 20705 076114 Invalid port number. Check the setting of the port number. 20705 076115 The specified resource is already used.
Table 108 Error codes (part code 20705) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20705 077104 A resource group cannot be deleted because resources are included in the specified resource group. Release all the resources in the specified resource W group, then retry the operation.
Part code 20722 Table 110 Error codes (part code 20722) Part Code Error Number Error Message Recommended Action Severity Level 20722 105283 "meta_resource" cannot be specified to Specify another resource group name. the resource group name. W 20722 105284 The specified resource group name is already used or reserved. Specify another resource group name. W 20722 105285 No more resource groups can be created. Delete unnecessary resource groups, then retry the operation.
Table 110 Error codes (part code 20722) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20722 107002 The processing cannot continue due to an internal logic contradiction. Refresh the window, and then retry the operation. E If this problem persists, contact HP Technical Support. 20722 107003 The processing cannot continue due to an internal logic contradiction. Refresh the window, and then retry the operation.
Table 112 Error codes (part code 20921) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20921 109212 When you return to the top window, the If you want to view the latest status, click the latest status may not be displayed on the Refresh View button on the top window. table. 20921 109213 Some of the specified pairs do not exist If you want to view the latest status, close this i in the configuration.
Table 113 Error codes (part code 20922) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20922 106116 A pool is not selected for the selected LDEV. Select a pool at [Select Pool]. W 20922 106117 The configuration information may have Retry the operation. If the same problem occurs been changed. again, close the windows, refresh it, then retry again. If the same problem persists despite retrying, please contact HP Technical Support.
Table 113 Error codes (part code 20922) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20922 106136 The selected volume cannot be displayed Select a pair where the setting is completed. because the setting is not yet completed. W 20922 106137 The selected LDEV can not be set because the L2 configuration of pair is already fixed.
Table 113 Error codes (part code 20922) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20922 106156 The operation cannot be done because Verify the status of the selected pair, and then W the status of L1 pair in the selected pair retry. If this problem persists, refresh the window, is incorrect. and then retry. 20922 106157 The operation cannot be done because Verify the status of the selected pair, and then W the status of a pair that shares a primary retry.
Table 113 Error codes (part code 20922) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20922 107003 The processing cannot continue due to an internal logic contradiction. Refresh the window, and then retry the operation. E If this problem persists, contact HP Technical Support. 20922 107004 The processing cannot continue due to an internal logic contradiction. Retry the operation. If the same problem occurs again, close the windows, refresh it, then retry again.
14 Support and other resources Contacting HP For worldwide technical support information, see the HP support website: http://www.hp.
• http://www.hp.com/support/manuals • http://www.hp.com/support/downloads • http://www.hp.
Table 114 Document conventions (continued) Convention Element Monospace text • File and directory names • System output • Code • Commands, their arguments, and argument values Monospace, italic text • Code variables • Command variables Monospace, bold text WARNING! CAUTION: IMPORTANT: NOTE: TIP: Emphasized monospace text Indicates that failure to follow directions could result in bodily harm or death. Indicates that failure to follow directions could result in damage to equipment or data.
Glossary allocation The ratio of allocated storage capacity versus total capacity as a percentage. Allocated storage refers to those logical devices (LDEVs) that have paths assigned to them. Allocated storage capacity is the sum of the storage of these LDEVs. Total capacity is the sum of the capacity of all LDEVs on the disk array. BC P9000 or XP Business Copy. An HP application that provides volume-level, point-in-time copies in the disk array. CHA Channel adapter.
parity group A set of hard disk drives that have the same capacity and that are treated as one group. A parity group contains both user data and parity information, which enables user data to be accessed if one or more drives in the group is not available. path A path is created by associating a port, a target, and a LUN ID with one or more LDEVs. Also known as a LUN. PAV Parallel access volume. PCB Printed circuit board. PDEV Physical device.
Index C contacting HP, 362 conventions document, 363 storage capacity values, 363 text symbols, 364 D document conventions, 363 related information, 362 documentation HP website, 362 providing feedback, 362 H help obtaining, 362 HP subscription service, 362 technical support, 362 R related documentation, 362 S storage capacity values conventions, 363 subscription service, HP, 362 symbols in text, 364 T technical support HP, 362 service locator website, 362 text symbols, 364 typographic conventions, 363
