HP P9000 Remote Web Console Messages Abstract This document lists the error codes and error messages for HP P9000 Remote Web Console for P9000 disk arrays, and provides recommended action for the error conditions.
© Copyright 2010, 2011 Hewlett-Packard Development Company, L.P. Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor's standard commercial license. The information contained herein is subject to change without notice.
Contents 1 P9500 messages and error codes.................................................................6 P9500 messages......................................................................................................................6 Message window format...........................................................................................................6 Advanced message window......................................................................................................
6 Message (part code group 4nnn).............................................................119 Part code 4005....................................................................................................................119 Part code 4010....................................................................................................................121 7 Message (part code group 5nnn).............................................................
Part Part Part Part code 9205....................................................................................................................310 code 9210.....................................................................................................................312 code 9605....................................................................................................................313 code 9610..............................................................................................
1 P9500 messages and error codes Unless otherwise specified, the term P9000 in this guide refers to the following disk array: • P9500 Disk Array The GUI illustrations in this guide were created using a Windows computer with the Internet Explorer browser. Actual windows may differ depending on the operating system and browser used. GUI contents also vary with licensed program products, storage system models, and firmware versions.
Access Synchronous Z messages only. If you are a Continuous Access Synchronous user, note the following: • The word M-VOL in Continuous Access Synchronous Z messages is equivalent to P-VOL in Continuous Access Synchronous messages. • The word R-VOL in Continuous Access Synchronous Z messages is equivalent to S-VOL in Continuous Access Synchronous messages. Recommended action This column provides recommended actions corresponding to the message.
Figure 3 Example of advanced message window 1 At the operation to change multiple settings at once, each result can be seen in the table shown under the message. Click an error code number written in the table that is linked to the changed result of each item to refer to the error. The advanced message window is also referable from the task window. (For details about the task window, see the HP P9000 Remote Web Console User Guide.
Remote Console-Remote Web Console error codes To find solutions to the Remote Web Console for P9500 errors, see “Error codes (part code 0001)” (page 10) and subsequent tables of this manual or the Troubleshooting chapter in the user guides for the program products causing the errors. “Error codes (part code 0001)” (page 10) and subsequent tables lists the error codes and error messages for Remote Web Console and provides recommended action for the error conditions.
2 Message (part code group 0nnn) This chapter includes the error messages with the part code 0001 to 0810. Part code 0001 Table 1 Error codes (part code 0001) 10 Part Code Error Number Error Message Recommended Action Severity Level 0001 1000 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. If this problem persists, please contact HP Technical Support. E 0001 1001 A time-out error occurred. Please wait The SVP reboots automatically.
Table 1 Error codes (part code 0001) (continued) Part Code Error Number Error Message Recommended Action Severity Level 0001 4007 An error occurred. If this problem persists, please contact HP Technical Support. Please contact HP Technical Support. E 0001 4008 An error occurred. If this problem persists, please contact HP Technical Support. Please contact HP Technical Support. E 0001 4009 An error occurred. If this problem persists, please contact HP Technical Support.
Table 1 Error codes (part code 0001) (continued) Part Code Error Number Error Message Recommended Action Severity Level Do either of the following if two users are displaying the Performance Monitor window or running the Export Tool: • Ask one of the users to display another window. • Ask one of the users to log off. • Wait for one of the users to quit the Export Tool. 12 0001 5509 Modify mode released due to inactivity.
Table 1 Error codes (part code 0001) (continued) Part Code Error Number Error Message Recommended Action Severity Level 0001 5638 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. If this problem persists, please contact HP Technical Support. E 0001 5639 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. If this problem persists, please contact HP Technical Support.
Table 1 Error codes (part code 0001) (continued) Part Code 14 Error Number Error Message Recommended Action persists, please contact HP Technical Support. clear the proxy cache. If that does not solve the problem and this problem persists, please contact HP Technical Support for resolution. Severity Level 0001 55034 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 1 Error codes (part code 0001) (continued) Part Code Error Number Error Message Recommended Action Severity Level 0001 65734 CVAE version information ID is invalid. Check the setting, and then retry the operation. CVAE version information ID is invalid. Check the setting, and then retry the operation. E 0001 66100 The Login could not be performed Please contact HP Technical Support. because a function failed to start during SVP initialization. E Please contact HP Technical Support.
Table 2 Error codes (part code 0002) (continued) Part Code Error Number Error Message Recommended Action Severity Level 0002 2015 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 0002 2016 The array is refreshing, or some other user is registering the setting. Wait, then retry the operation. W 0002 2145 An error occurred while connecting to the subsystem. Wait, then retry the operation.
Table 2 Error codes (part code 0002) (continued) Part Code Error Number Error Message Recommended Action Severity Level 0002 7060 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 0002 7111 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 0002 7211 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 3 Error codes (part code 0003) (continued) 18 Part Code Error Number Error Message Recommended Action Severity Level 0003 2004 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 0003 2005 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 0003 2006 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 3 Error codes (part code 0003) (continued) Part Code Error Number Error Message Recommended Action Severity Level 0003 2100 An error occurred while connecting to the storage system. The configuration may be inconsistent. Click [Refresh All] on the [File] menu, then refresh the configuration. W 0003 3000 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 0003 3001 An error occurred during SVP processing.
Table 4 Error codes (part code 0004) (continued) Part Code Error Number Error Message Recommended Action Severity Level 0004 6037 The subsystem status is invalid. If the same problem persists despite retrying, please contact HP Technical Support. E 0004 8010 The subsystem status is invalid. If the same problem persists despite retrying, please contact HP Technical Support.
Part code 0007 Table 7 Error codes (part code 0007) Part Code Error Number Error Message Recommended Action Severity Level 0007 6012 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. If this problem persists, please contact HP Technical Support. E 0007 6022 File access error occurred.
Part code 0010 Table 8 Error codes (part code 0010) Part Code Error Number Error Message Recommended Action Severity Level 0010 6023 An error occurred during processing. If If this problem persists, please contact this problem persists, please contact HP HP Technical Support. Technical Support. E 0010 6027 A network error occurred. The probable You cannot connect to the SVP because causes might be one of the following.: of factors, such as a network error or SVP error. Check the IP address.
Table 8 Error codes (part code 0010) (continued) Part Code Error Number Error Message Recommended Action Severity Level file will be saved, and also check the free space on the drive. 0010 57103 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. If this problem persists, please contact HP Technical Support. E 0010 57104 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Part code 0110 Table 11 Error codes (part code 0110) 24 Part Code Error Number Error Message 0110 5030 The displayed information has not been Specify the data to be registered in the changed. Try again. SVP, then retry the operation. W 0110 7060 An error occurred in the client logic. E 0110 7440 An error occurred during processing. If If this problem persists, please contact this problem persists, please contact HP HP Technical Support. Technical Support. E 0110 8100 A SIM occurred.
Table 11 Error codes (part code 0110) (continued) Part Code Error Number Error Message Recommended Action Severity Level If configuration changes have been made incorrectly, retry the operation. 0110 59002 The storage system is in internal process, Wait for a while, then click [OK] and or some other user is changing the change the mode to Modify. configuration. Wait, then click [OK] and change the mode to Modify.
Part code 00122 Table 14 Error codes (part code 00122) Part Code Error Number Error Message Recommended Action Severity Level 00122 105260 The free space for storing audit log files Download the Audit Log. is running out. Usage Rate {0}% W 00122 105261 The free space for storing audit log files Download the Audit Log. has run out. The old audit log information will be overwritten.
Table 15 Error codes (part code 00222) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00222 105220 The re-entered new password does not match the new password entered previously. Check the setting(s). W 00222 105221 No check box is selected. Check the setting(s). W 00222 105222 The user to be registered is not selected. Select a user to be registered, then retry W the operation. 00222 105223 No table row, or two or more table rows Select one table row.
Table 15 Error codes (part code 00222) (continued) 28 Part Code Error Number Error Message 00222 105331 The value that can be input to the Set a value within the range. number of retries of authentication server is 1 to 50. W 00222 105332 The base DN of authentication server is This is a compulsory input item. not input. W 00222 105333 The base DN of authentication server is Enter with 1 to 255 characters. too long.
Table 15 Error codes (part code 00222) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00222 105351 Other than the numeric characters are input to the specified primary port number of authentication server. Enter with numeric characters. W 00222 105352 The value that can be input to the primary port number of authentication server is 1 to 65535. Set a value within the range. W 00222 105353 The secondary host name of authentication server is not input.
Table 15 Error codes (part code 00222) (continued) 30 Part Code Error Number Error Message Recommended Action 00222 105373 Invalid characters are used in the specified realm name of authentication server. Enter with alphanumeric characters and W symbols( - . ). 00222 105374 The clock skew of authentication server is not input. This is a compulsory input item. W 00222 105375 Other than the numeric characters are input to the specified clock skew of authentication server.
Table 15 Error codes (part code 00222) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00222 105393 Other than the numeric characters are input to the specified timeout value of external user group mapping. Enter with numeric characters. W 00222 105394 The value that can be set for the timeout Set a value within the range. of external user group mapping is 1 to 120. W 00222 105395 The retry interval for the external user group mapping is not input.
Table 15 Error codes (part code 00222) (continued) Part Code Error Number Error Message Recommended Action 00222 105411 Invalid characters are used in the specified secondary host name of external user group mapping. Enter with alphanumeric characters and W symbols( - . ). 00222 105412 The secondary port number of external user group mapping is not input. This is a compulsory input item. 00222 105413 Other than the numeric characters are Enter with numeric characters.
Table 15 Error codes (part code 00222) (continued) Part Code Error Number Error Message Recommended Action Severity Level specified user group, then retry the operation. 00222 106051 The number of user groups that can be associated with a user has reached the maximum. Decrease the number of user groups that W are associated with the user, then retry the operation. 00222 106052 Failed to change the user account information. Check the following contents: W • If the specified user exists.
Table 15 Error codes (part code 00222) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00222 106064 Failed to change the user group information. Verify the following: W • If the specified user group is registered • If there is no built-in group in the specified user groups • If the specified resource group is registered. 00222 106065 Failed to delete the user group. Verify the following. W • If the specified user group is registered.
Table 15 Error codes (part code 00222) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00222 106076 The password cannot be changed due to one of the following reasons. W • If the specified user is a local user, verify the registered status of the user. • The selected user does not exist in local accounts.
Table 16 Error codes (part code 0290) (continued) Part Code Error Number Error Message Recommended Action Severity Level 0290 5090 The RMI time-out period is too short compared to the time to keep the RMI object. Reply to this message. - 0290 5100 The Polling period is too long compared Reply to this message. to the time to keep the RMI object. - 0290 5101 Specify at least 1 polling method. Reply to this message.
Table 16 Error codes (part code 0290) (continued) Part Code Error Number Error Message Recommended Action Severity Level 0290 6150 Failed to open the user account list file. If the same error occurs again despite retrying, please contact HP Technical Support. - 0290 6160 Failed to open the user account list file. If the same error occurs again despite retrying, please contact HP Technical Support. - 0290 6170 Failed to open the user account list file.
Table 16 Error codes (part code 0290) (continued) 38 Part Code Error Number Error Message Recommended Action Severity Level 0290 9005 Are you sure you want to restore these files? Reply to this message. - 0290 56111 File name is not specified. Specify the file name, then retry the operation. - 0290 56121 File name is not specified. Specify the file name, then retry the operation. - 0290 56131 File name is not specified. Specify the file name, then retry the operation.
Table 16 Error codes (part code 0290) (continued) Part Code Error Number Error Message Recommended Action Severity Level 0290 56611 Failed to create the file. If this problem persists, please contact HP Technical Support. - 0290 56621 Failed to create the file. If this problem persists, please contact HP Technical Support. - 0290 56631 Failed to create the file. If this problem persists, please contact HP Technical Support. - 0290 56791 Failed to delete work files.
Table 17 Error codes (part code 0305) (continued) Part Code Error Number Error Message Recommended Action Severity Level 0305 6023 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 0305 7060 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 0305 7102 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 18 Error codes (part code 0310) (continued) Part Code Error Number Error Message Recommended Action Severity Level 0310 5040 The maximum number of IP Address is 32. Reduce the number, and retry. W 0310 5041 The maximum number of Community name is 32. Reduce the number, and retry. W 0310 5050 This Community name is already in use. Check the content of the operation. W 0310 5051 This IP address is already in use. Check the content of the operation.
Table 19 Error codes (part code 0405) (continued) Part Code Error Number Error Message Recommended Action 0405 5073 To install/remove this program product, Install or remove the related program you must install/remove another program product first. product first.
Table 19 Error codes (part code 0405) (continued) Part Code Error Number Error Message Recommended Action Severity Level To remove this program product, you must remove another program product first.
Table 19 Error codes (part code 0405) (continued) Part Code Error Number Error Message Recommended Action Severity Level 0405 5525 You cannot remove Data Retention, because "S-VOL disable" or "Reserve" setting remains. Remove the "S-VOL disable" setting. W 0405 6012 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 0405 6022 The SVP is busy. Please wait for a while, If the same problem persists despite and then retry the operation.
Table 19 Error codes (part code 0405) (continued) Part Code Error Number Error Message Recommended Action Severity Level Replacing the PC Turning on, then off the DKC (care should be taken.) 0405 8003 The subsystem status is invalid. Isolate the abnormal section following the procedure below: E Rebooting the PC. If this does not fix the problem: Checking the LAN card/LAN cable. If this does not fix the problem: Checking the IP address of the PC. If this does not fix the problem: Replacing the PC.
Table 19 Error codes (part code 0405) (continued) Part Code Error Number Error Message Recommended Action Severity Level 0405 57094 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 0405 57097 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 0405 57098 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 21 Error codes (part code 0410) (continued) Part Code Error Number Error Message Recommended Action Severity Level 0410 55002 A file name is invalid due to one of the following reasons: Check the file name and retry the operation. W • The file name is not specified. • The file name consists of more than 200 characters. • The file name includes an inappropriate character. 0410 57000 Failed to refer to the license key information. Retry the same operation several times.
Table 22 Error codes (part code 0605) (continued) Part Code Error Number Error Message Recommended Action Severity Level 0605 2095 Another maintenance processing or failure handling is in progress. Wait for a while, then retry the operation. W 0605 2200 The Concurrent Copy or the Compatible Cancel the Concurrent Copy job or W XRC operation is in progress in the target delete a Compatible XRC pair via the volumes. host.
Table 22 Error codes (part code 0605) (continued) Part Code Error Number Error Message Recommended Action Severity Level 0605 2522 The volume is reserved by Auto LUN. Release the definition of a reserved volume, then retry the operation. W 0605 3003 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 0605 5013 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 22 Error codes (part code 0605) (continued) 50 Part Code Error Number Error Message Recommended Action Severity Level 0605 8958 An error occurred on the DKC side. If this problem persists, please contact HP Technical Support. E 0605 8966 An error occurred on the DKC side. If this problem persists, please contact HP Technical Support.
Table 22 Error codes (part code 0605) (continued) Part Code Error Number Error Message Recommended Action Severity Level Systems or the Disconnect External Volume is in progress. Volumes, put the external volume in normal status, then retry the operation. 0605 58410 The cache mode cannot be changed because the bind mode is set to the specified volume. Release the bind mode setting, then retry W the operation. 0605 58411 Set the same cache mode to all the volumes that compose a LUSE volume.
Table 22 Error codes (part code 0605) (continued) 52 Part Code Error Number Error Message Recommended Action Severity Level 0605 65799 There are no setting lines of NewPathGroup. Check the contents of the spreadsheet. W 0605 65800 The number of NewPathGroup setting lines exceeds the limit. Check the contents of the spreadsheet. W 0605 65801 There are no setting lines of the ExG. Check the setting of ExG. W 0605 65802 There are no setting lines of TargetPathGroup.
Table 22 Error codes (part code 0605) (continued) Part Code Error Number Error Message Recommended Action Severity Level corresponding to that of another external volume in the same External Path Group. 0605 66520 Mainframe volume and intermediate volume cannot be set because the package for mainframe system is not mounted. Check the mounted packages. W 0605 66568 Multiple operation tags are defined. Check the contents of the spreadsheet. W 0605 66675 The syntax of the parameter is invalid.
Table 22 Error codes (part code 0605) (continued) 54 Part Code Error Number Error Message 0605 66744 It is not set within the range where LDEV Check the setting of LDEV capacity. capacity can be used. W 0605 66748 A value different from SSID that has already been set is specified. Check the setting of SSID. W 0605 66749 The number of paths has reached the maximum number. Check the setting of path. W 0605 66750 The specified WWN is not registered. Check the specified WWN.
Table 22 Error codes (part code 0605) (continued) Part Code Error Number Error Message Recommended Action Severity Level 0605 68901 An external volume was not able to be recovered. Check the status of the mapping path and resolve the root cause of blockade, then retry the operation. W 0605 68902 The external volume was able to be restored, but some of mapping paths were not able to be restored normally.
Table 22 Error codes (part code 0605) (continued) Part Code Error Number Error Message Recommended Action Severity Level contains the external volume that belongs to a resource group to which the user has no access right. 0605 78056 The operation cannot be done because Verify the resources allocation for the the external volume which belongs to a user with security administrator role. resource group to which the user has no access right uses the specified external WWN.
Table 23 Error codes (part code 00622) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00622 105239 The number of alternate paths that can Check the number of selected alternate be set to an external volume exceeds the paths. maximum. 00622 105240 Failed to allocate an External Path Group Check the number of registered external W ID. path groups. 00622 105241 An external volume that can be added was not found by the result of VolumeDiscovery.
Table 23 Error codes (part code 00622) (continued) Part Code Error Number Error Message Recommended Action Severity Level right is connected to the specified external path group. 58 00622 105269 The specified external volume cannot be Verify the resources allocation for the used because the user has no access user with security administrator role. right to a resource group to which the external volume belongs.
Table 23 Error codes (part code 00622) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00622 106055 The selected emulation type cannot be Release the command device, or select set because a command device is set to another volume. an external volume. W 00622 106056 An emulation type that can not be set is Specify a supported emulation type. selected.
Table 23 Error codes (part code 00622) (continued) Part Code Error Number Error Message Recommended Action Severity Level despite retrying, please contact HP Technical Support. 00622 107003 The processing cannot continue due to an internal logic contradiction. Refresh the window, then retry the operation. If the same problem persists despite retrying, please contact HP Technical Support. E 00622 107004 The processing cannot continue due to an internal logic contradiction. Retry the operation.
Part code 00722 Table 25 Error codes (part code 00722) Part Code Error Number Error Message Recommended Action Severity Level 00722 105423 A radio button for Primary Server is not Check the setting. selected. W 00722 105424 A radio button for Secondary Server is Check the setting. not selected. W 00722 105425 A radio button for Primary Server IP Address is not selected. Check the setting. W 00722 105426 A radio button for Secondary Server IP Check the setting. Address is not selected.
3 Message (part code group 1nnn) This chapter includes the error messages with the part code 1005 to 1310. Part code 1005 Table 27 Error codes (part code 1005) Part Code Error Number Error Message Recommended Action Severity Level 1005 1002 The specified volume cannot be set as a Select another volume. command device or a component of a LUSE volume, because it is being used as the volume of Remote Copy, Business Copy, Auto LUN, or Snapshot.
Table 27 Error codes (part code 1005) (continued) Part Code Error Number Error Message Recommended Action Severity Level and request the configuration information setting again. 1005 1022 Invalid host mode. The configuration information has been W changed already. Check the settings, and request the configuration information setting again. 1005 1023 Invalid Fibre address. The configuration information has been W changed already.
Table 27 Error codes (part code 1005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 1005 1108 The following volumes cannot be specified when you change the command device configurations: Check the setting, then retry the operation. W • Volumes reserved by Auto LUN • Volumes other than the open-system volumes (including unmounted volumes) • System Disk volume 64 1005 1110 Invalid characters are specified in the nickname to be used in HOST GROUP and WWN.
Table 27 Error codes (part code 1005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 1005 1135 When setting the port information (Fibre Check the setting(s), then retry the Address/Fibre Topology/Channel operation. Speed), multiple change instructions are set to the same port. 1005 1138 The same setting is specified at LUNM operation. The configuration information has been W changed already.
Table 27 Error codes (part code 1005) (continued) 66 Part Code Error Number Error Message 1005 1356 You could not add the host group to the To add the host group, change the initiator or external port. attribute of the specified port to Target or RCU Target. 1005 1357 S-VOLs remain on the Fibre-RCU port. This operation may cause a fatal damage to the S-VOLs. Please stop this operation. If you want to continue this operation, please remove the S-VOLs from the RCU port first.
Table 27 Error codes (part code 1005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 1005 1928 Addition or deletion of paths for LUN0 Set Host Mode Option 60 to OFF, and cannot be done because Host Mode then execute addition or deletion of Option 60 is set to ON. Also, setting paths for LUN 0. change of Host Mode Option 60 and path change (addition or deletion) for LUN 0 cannot be done at the same time. Execute the changing operations separately.
Table 27 Error codes (part code 1005) (continued) 68 Part Code Error Number Error Message Recommended Action Severity Level 1005 2504 No settings can be made because of a volume reserved for RAID Manager. Release the reserved attribute of the target volume by using Data Retention. W 1005 3002 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 1005 3003 An error occurred during SVP processing.
Table 27 Error codes (part code 1005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 1005 55561 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 1005 55566 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 1005 55569 The specified Group-ID is already registered. Check the setting.
Table 27 Error codes (part code 1005) (continued) Part Code Error Number Error Message Recommended Action Severity Level a resource group to which the port belongs. 1005 76511 The specified host group cannot be used Verify the resources allocation for the because the user has no access right to user with security administrator role. a resource group to which the host group belongs.
Table 28 Error codes (part code 01022) (continued) Part Code Error Number Error Message Recommended Action Severity Level 01022 105021 No more HBA WWN can be registered, Check the setting(s). because the number of registered HBA WWNs has reached the maximum. W 01022 105022 The selected information cannot be added, because a duplicated HBA WWN is in the information being selected. Only the first duplicate item is added. Check the contents that have been added.
Table 28 Error codes (part code 01022) (continued) 72 Part Code Error Number Error Message 01022 105041 [Detail] is clicked in the state of selecting Select one table row. multiple table rows. W 01022 105042 [Delete] is clicked without selecting any row. W 01022 105043 The processing cannot be done because Check if any of target host group to be W there is no data in the [Selected Host set exists in the [Selected Host Groups] Groups] table. table.
Table 28 Error codes (part code 01022) (continued) Part Code Error Number Error Message Recommended Action Severity Level 01022 105079 Changing to the external or the initiator Check the setting(s). port cannot be done, because a host group other than Host Group 0 is set. W 01022 105080 The specified port cannot be changed into External or Initiator. W 01022 105081 The setting cannot be changed because Check the channel PCB. of the unsupported port speed.
Table 28 Error codes (part code 01022) (continued) Part Code Error Number Error Message Recommended Action Severity Level name is used in the same port, or, it is used in the item that has been moved in the [Selected Host Groups] table. 01022 105209 The host mode is left blank. Set the item that is left blank, then retry the operation. W 01022 105210 There are blank items in the Host Mode Set the item that is left blank, then retry Options Table. the operation.
Table 28 Error codes (part code 01022) (continued) Part Code Error Number Error Message Recommended Action Severity Level If the same problem persists despite retrying, please contact HP Technical Support. 01022 106503 The process cannot be continued, because there is no necessary data for the configuration. Refresh the window, then retry the operation. E If the same problem persists despite retrying, please contact HP Technical Support.
Table 28 Error codes (part code 01022) (continued) Part Code Error Number Error Message Recommended Action Severity Level 01022 107001 The processing cannot continue due to an internal logic contradiction. Refresh the window, then retry the operation. E If the same problem persists despite retrying, please contact HP Technical Support. 01022 107002 The process cannot continue due to internal logic contradiction. Refresh the window, then retry the operation.
Table 28 Error codes (part code 01022) (continued) Part Code Error Number Error Message Recommended Action Severity Level 01022 108012 The specified LDEV is a pool volume. Check the setting(s). W 01022 108013 The specified LDEV is a V-VOL. Check the setting(s). W 01022 108014 The specified LDEV is a remote command Check the setting(s). device. W 01022 108015 The selected LDEV has been set as a quorum disk volume. Check the setting(s).
Table 29 Error codes (part code 1305) (continued) Part Code Error Number Error Message Recommended Action Severity Level 1305 66572 Declaration is invalid. Check the contents of the spreadsheet. W 1305 66573 The number of lines or the number of characters in one line exceeds the maximum number. Check the contents of the spreadsheet. W 1305 66574 There is a line that cannot be interpreted Check the contents of the spreadsheet. as an element of the spreadsheet.
Table 30 Error codes (part code 1310) (continued) Part Code Error Number Error Message Recommended Action Severity Level 1310 69048 Insufficient permission to operate this. The following role is required for this operation. W • Storage Administrator (Initial Configuration) Contact the security manager, and register the user to User Group who has a necessary role. 1310 69049 Insufficient permission to operate this. The following role is required for this operation.
4 Message (part code group 2nnn) This chapter includes the error messages with the part code 2005 and 2010. Part code 2005 Table 31 Error codes (part code 2005) Part Code Error Number Error Message Recommended Action 2005 1002 The specified volume cannot be set as a Select another volume. command device or a component of a LUSE volume, because it is being used as the volume of Remote Copy, Business Copy, Auto LUN, or Snapshot. W 2005 1006 The specified LUSE volume cannot be Select another volume.
Table 31 Error codes (part code 2005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 2005 1137 Failed to form a LUSE volume because the number of LUSE volumes exceeds the maximum that can be set in a disk array subsystem. The configuration information has been W changed already. Check the settings, and request the configuration information setting again. 2005 1138 The specified LDEV is already used for another LUSE volume. Check the specified contents.
Table 31 Error codes (part code 2005) (continued) 82 Part Code Error Number Error Message Recommended Action Severity Level 2005 1925 The combination order of LUSE volume is incorrect. Check the settings. W 2005 2005 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 2005 2009 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 31 Error codes (part code 2005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 2005 5877 The setting cannot be done because you All the resource group IDs that are set to W have no access right to the subject the storage system must be assigned to resource group. the user account that logs in to Remote Web Console. 2005 6012 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Part code 2010 Table 32 Error codes (part code 2010) 84 Part Code Error Number Error Message Recommended Action Severity Level 2010 5030 The LUSE volume cannot be released because the access attribute of the specified volume is not Read/Write. Correct the settings, then retry. W 2010 5032 There are no LDEVs to set the LUSE top volume. Check the specified LDEVs. Correct the specified content, and retry. W 2010 5033 There are no available LDEVs to make the LUSE. Check the specified LDEVs.
5 Message (part code group 3nnn) This chapter includes the error messages with the part code 3005 to 3305. Part code 3005 Table 33 Error codes (part code 3005) Part Code Error Number Error Message Recommended Action Severity Level 3005 1910 The specified volume contains Snapshot Check the setting of the specified pair. volumes. W 3005 1911 The specified volumes contain Pool-VOLs. W 3005 2011 The status of the disk subsystem requires Please contact HP Technical Support.
Table 33 Error codes (part code 3005) (continued) Part Code Error Number Error Message Recommended Action Severity Level • Replacement of an OEM drive microprogram is in progress • LDEV Shredding is in progress Therefore the specified operation cannot be executed. 86 3005 2200 The Concurrent Copy or the Compatible If the Concurrent Copy or the Compatible W XRC operation is in progress in the XRC operation is in progress in the target target volumes.
Table 33 Error codes (part code 3005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 3005 2518 A pair of Business Copy, Business Copy Split the pair, then retry the operation. W Z, or Snapshot is defined. If a reserve volume is defined, cancel the reservation. If the Quick Split mode is on, suspend the pair, then split. 3005 2519 The volume is reserved by Business Copy or Business Copy Z. Cancel the reservation, and then retry the operation.
Table 33 Error codes (part code 3005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 3005 7060 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 3005 7111 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 3005 7310 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 33 Error codes (part code 3005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 3005 55516 This function is not available, because the program product is not installed. Install the program product. W 3005 55517 The specified volume is used as a Pool-VOL. Specify another volume. W 3005 55519 The specified pool does not exist. Check the setting(s). W 3005 55594 An error occurred during SVP processing.
Table 33 Error codes (part code 3005) (continued) Part Code Error Number Error Message 3005 58470 The operation cannot be done, because Add some Pool-VOL, or decrease the the usage of the specified Pool is 100% snapshot data by restoring or deleting (full). the Snapshot pairs. 3005 58471 The shared memory for the V-VOL management area is insufficient. 3005 58472 Acquisition of the pool information has When the pool information cannot be failed.
Table 33 Error codes (part code 3005) (continued) Part Code Error Number Error Message Recommended Action Severity Level maintained is in PSUS status or being restored. 3005 58626 A Snapshot pair is defined. Cancel the pair definition, then retry the W operation. 3005 58706 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. 3005 65650 The specified volume is used as a System Disk volume. Check the setting of the specified volume.
Table 33 Error codes (part code 3005) (continued) Part Code Error Number Error Message Recommended Action Severity Level or Quick Restore is not in the operation, then retry the operation. 92 3005 65767 The specified volume contains a quorum Check the specified volume. disk. W 3005 65790 The specified volume includes a remote Check the specified volume. command device being used by a mirror of the journal group. W 3005 68722 The specified volume is not a Thin Provisioning volume.
Table 33 Error codes (part code 3005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 3005 68798 Failed to delete the pool. When the pool cannot be deleted, do the following: W Pool cannot be deleted when: • Check the installation status of the V-VOL management area, when the V-VOL management area is not • The V-VOL management area is not initialized. installed.
Table 33 Error codes (part code 3005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 3005 68823 The specified volume is currently used by Auto LUN. Wait until the process of Auto LUN is completed, then retry the operation. E If this problem persists, please contact HP Technical Support. 3005 68824 The specified volume is currently used by Continuous Access Synchronous, Continuous Access Synchronous Z, or External Storage Access Manager.
Table 33 Error codes (part code 3005) (continued) Part Code Error Number Error Message Recommended Action 3005 78009 You cannot expand the V-VOLs for the volumes that are being used in the following program products: Change the setting to not use the volumes W of the following program products as a target of expanding V-VOL, and then retry the operation.
Table 33 Error codes (part code 3005) (continued) 96 Part Code Error Number Error Message Recommended Action Severity Level 3005 78020 The operation cannot be executed, because the available period to stop shrinking pools has elapsed. You cannot stop shrinking pools. Wait until pools are shrunk. W 3005 78024 The encryption key cannot be created, Check the specified encryption key because an already created encryption number. key number is included in the specified encryption key number.
Table 33 Error codes (part code 3005) (continued) Part Code Error Number Error Message 3005 78042 The operation cannot be executed Wait until the pool is shrunk or the tier because the pool where the Thin is relocated, or abort it. Provisioning Volume belongs to is now in pool shrinking or tier relocation process. 3005 78043 The operation cannot be executed because the specified pool has following problems. • The pool usage exceeds the threshold.
Table 33 Error codes (part code 3005) (continued) Part Code Error Number Error Message Recommended Action 3005 78060 The multi tier pool cannot be disabled because the RAID level of each tier is different. Check the configuration of the supported W RAID levels, then retry the operation. 3005 78061 Failed to delete the pool. Wait until the processing is completed, Pools cannot be deleted when they are then retry the operation.
Table 33 Error codes (part code 3005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 3005 78111 External volumes with mixed cache mode setting, enabled and disabled, cannot be used as pool volumes in a THP pool. Verify the cache mode of the subject external volumes. W 3005 78112 External volumes with cache mode disabled cannot be specified as pool volumes for the pool. Verify the cache mode of the subject external volumes.
Table 35 Error codes (part code 03022) (continued) Part Code Error Number Error Message 03022 105138 The specified LDEV is a reserved volume Check the setting(s). of Auto LUN. W 03022 105139 The selected LDEV has been set to a LUSE volume. Check the setting(s). W 03022 105140 The specified LDEV is a remote command Check the setting(s). device. W 03022 105141 The selected LDEV has been set as a journal volume. Check the setting(s).
Table 35 Error codes (part code 03022) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03022 105164 LDEVs with different emulation types are Check the setting(s). selected. W 03022 105165 LDEVs with different RAID levels are selected. Check the setting(s). W 03022 105166 No more volumes can be created Check the setting(s).
Table 35 Error codes (part code 03022) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03022 105186 No more V-VOL can be added to the selected pool. Check the setting(s). W 03022 105187 A pool in the abnormal state is selected. Check the setting(s). W 03022 105188 There is no LDEV ID that can be set in the selected pool.
Table 35 Error codes (part code 03022) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03022 105271 The number of free spaces that exist in the selected parity group exceeds the number of volumes that can be set. Select the free spaces again from the Select Free Space window. W 03022 105272 Data Output cannot be set more than 3. Check the setting(s).
Part code 03121 Table 36 Error codes (part code 03121) Part Code Error Number Error Message Recommended Action Severity Level 03121 109205 Are you sure you want to initialize all the THP pools? To continue the processing, click [OK]. Otherwise, click [Cancel]. W Part code 03122 Table 37 Error codes (part code 03122) Part Code Error Number Error Message Recommended Action Severity Level 03122 105264 The password is invalid. Check the password, then retry the operation.
Table 37 Error codes (part code 03122) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03122 106019 The allocation cannot be done from the specified pool ID. Specify a pool ID that is smaller than the W one specified before, then retry the operation. 03122 106021 The selected volumes cannot be specified Select the same volume type, then retry as a pool volume, because the volume the operation. types are different.
Table 37 Error codes (part code 03122) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03122 106036 The operation cannot be executed, because the specified pool volumes contain an abnormal pool volume. Check the state of the specified pool volumes, then retry the operation. W 03122 106037 The setting cannot be executed, because Execute any of the following actions, the specified pool has no free space. then retry the operation.
Table 37 Error codes (part code 03122) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03122 106095 The operation cannot be done because the configuration of the specified pools does not meet the conditions below. Check the configuration of the pools. W • The smart pool is enabled. • The tier management is in manual operation. 03122 106096 Failed to get the pool information. Check the status of the pool, and then retry the operation.
Table 37 Error codes (part code 03122) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03122 107023 The processing cannot continue due to an internal logic contradiction. Refresh the window, then retry the operation. If the same problem persists despite retrying, please contact HP Technical Support. E 03122 109205 Are you sure you want to initialize all pools? Click [OK] to continue, or click [Cancel] E to cancel the processing.
Table 38 Error codes (part code 3205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 3205 5013 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 3205 5099 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 3205 5511 A necessary program product is not installed. Install the necessary program product(s).
Table 38 Error codes (part code 3205) (continued) 110 Part Code Error Number Error Message Recommended Action 3205 56516 The configuration of Continuous Access Synchronous or Continuous Access Synchronous Z is defined. Release the configuration definition for W Continuous Access Synchronous or Continuous Access Synchronous Z, then retry the operation. 3205 56517 The configuration of Business Copy, Release the configuration definition for Business Copy Z, or Snapshot is defined.
Table 38 Error codes (part code 3205) (continued) Part Code Error Number Error Message Recommended Action Severity Level package for mainframe system is not mounted. 3205 66747 The value of SSID is not set within the available range. Check the setting of SSID. W 3205 66748 A value different from SSID that has already been set is specified. Check the setting of SSID. W 3205 68725 The shared memory for the V-VOL management area is insufficient.
Table 38 Error codes (part code 3205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 3205 78061 The specified emulation type is different Change the emulation type to be set to from that of the pool specified to the volume. associate with. W 3205 78062 The specified values of CU and pool ID Set the values of CU and pool ID to the do not follow the rule to create a volume odd or the even number. of TSE attribute.
Table 39 Error codes (part code 03222) (continued) Part Code Error Number Error Message Recommended Action Severity Level environment. Verify if the system is affected or not. 03222 105433 Reclaim Zero Pages cannot be done to the TSE volume. Check the setting(s). W 03222 105434 The TSE volume and the Thin Provisioning Z volume cannot be expanded at the same time. Select volumes of the same attribute when expanding.
Table 40 Error codes (part code 3305) (continued) 114 Part Code Error Number Error Message Recommended Action Severity Level 3305 1101 An operation is specified for the uninstalled volume. Correct the settings, then retry the operation. W 3305 1103 An operation is specified for the uninstalled Parity Group. Correct the settings, then retry the operation. W 3305 1104 Subsystem ID cannot be set alone. Request the change of the Subsystem ID W along with the VLL operation.
Table 40 Error codes (part code 3305) (continued) Part Code Error Number Error Message Recommended Action Severity Level Please wait for a while, and then retry the operation. To perform a VLL operation on an external volume, check the status of the path to the external volume. 3305 2085 Copying is in progress for Remote Copy, Wait a while, then retry the operation. Business Copy, Business Copy Z, Snapshot, or Auto LUN pairs.
Table 40 Error codes (part code 3305) (continued) Part Code Error Number Error Message Recommended Action Severity Level 3305 2205 Devices to be maintained include journal Delete all pairs to which the journal volumes. volumes belong. W 3305 2515 One of the following is defined: a Remote Copy pair, a Continuous Access Journal pair, or a Continuous Access Journal Z pair. Release the pair definition or delete command devices defined by Business Continuity Manager, then retry the operation.
Table 40 Error codes (part code 3305) (continued) Part Code Error Number Error Message Recommended Action Severity Level 3305 6022 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 3305 6023 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 3305 6092 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 40 Error codes (part code 3305) (continued) Part Code Error Number Error Message Recommended Action 3305 65790 The specified volume includes a remote Check the specified volume. command device being used by a mirror of the journal group. W 3305 68802 The specified volume includes a system disk being used by the audit log. W 3305 75017 The volume of 3390-V cannot be created You cannot have a 3390-V volume in a with the RAID level of the specified parity RAID 1 (2D+2D) parity group. group.
6 Message (part code group 4nnn) This chapter includes the error messages with the part code 4005 and 4010. Part code 4005 Table 41 Error codes (part code 4005) Part Code Error Number Error Message Recommended Action Severity Level 4005 5010 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 4005 5040 The number of requests exceeds the Reduce the number of requests, and then W maximum number that can be processed. retry the operation.
Table 41 Error codes (part code 4005) (continued) Part Code Error Number Error Message Recommended Action 4005 55245 The number of cache residency areas set Check the settings, then retry the for the CLPR exceeds the maximum operation. available number of cache residency areas. Severity Level W CLPR No:%s 4005 55246 The total number of Cache Residency Check the settings, then retry the areas set for the CLPRs and the maximum operation.
Table 41 Error codes (part code 4005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 4005 55576 An LDEV number that does not apply to Check the setting. the selected CU group has been specified. W 4005 56542 The prestaging is not executed because the prestaging area does not exist. Check the Cache Residency setting. W 4005 58511 The current Cache Residency setting Wait, then retry the operation.
Table 42 Error codes (part code 4010) (continued) 122 Part Code Error Number Error Message Recommended Action Severity Level 4010 2080 Prestaging not completed. Wait a while, click [Refresh], and change the same configuration again. Check the DKC status. If the same error occurs, please contact HP Technical Support.
7 Message (part code group 5nnn) This chapter includes the error messages with the part code 5105 to 5307. Part code 5105 Table 43 Error codes (part code 5105) Part Code Error Number Error Message Recommended Action Severity Level 5105 2002 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 5105 2003 An error occurred during SVP processing. Use the SVP to check if the DKC is in the E normal status, then retry.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 6023 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 5105 6036 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 5105 6092 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 5105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Change the gathering interval, and retry E the operation. 5105 66017 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 8708 The pair status of the secondary data volume is incorrect. Refresh the window, and check the pair W status. If possible, retry the operation on the secondary data volume. 6505 8709 Remote Copy operation was rejected. Replace the channel adapter, then retry E the operation. 6505 8710 The pair status of the specified data volume is incorrect.
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 8727 The number of minimum paths exceeds the number of normal paths. Do either of the following to recover from W the error: • If the error code is 100c, add normal paths, then set the minimum number of paths. • If the error code is 100d, add normal paths, then delete paths. Alternatively, reduce the minimum number of paths, then delete paths.
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 8736 The specified remote storage system contains journals or data volume pairs for remote copy operations. Delete data volume pairs of the specified W remote storage system. Then delete journals, if any. Ensure that there are no data volume pairs and journals, then retry the operation. 6505 8737 An internal error occurred.
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 8753 An internal error occurred. Check the SSB log, then contact HP Technical Support. E 6505 8757 One side of the cache or the shared memory is blocked in the primary storage system. Check the status of the cache and the shared memory in the primary storage system. E Ensure that the cache and shared memory is not blocked.
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message Recommended Action Severity Level Check the status of the secondary data volume.
Table 56 Error codes (part code 6505) (continued) 194 Part Code Error Number Error Message Recommended Action Severity Level 6505 8890 The specified port is being initialized. Wait until the initialization of the port ends, and retry the operation. W 6505 8891 Logical paths exist on the port. Delete the logical paths on the port and W retry the operation. 6505 8893 An internal error occurred. Check the SSB log, then contact HP Technical Support. 6505 8894 Jobs exist on the port.
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 8934 The Add Pair (Paircreate) operation Check the configuration of the specified W failed because the specified secondary secondary data volume. data volume was a NAS system volume. 6505 8936 The Paircreate (Add Pair) operation Check the microcode version of the failed. The microcode version of the secondary storage system.
Table 56 Error codes (part code 6505) (continued) 196 Part Code Error Number Error Message 6505 58012 Invalid parameter (number of initial copy Check the specified number of initial activities). copy activities. 6505 58013 The specified volume does not exist or is unusable. Check the status of the specified volume. W 6505 58014 Pinned slot(s) exists. Please contact HP Technical Support. E 6505 58015 The specified volume is blocked. Please contact HP Technical Support.
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 58032 The threshold for starting creation of synchronous journal must be larger than the threshold for ending creation of synchronous journal. Ensure that the threshold for starting W creation of synchronous journal is larger than the threshold for ending creation of synchronous journal. 6505 58033 The total cache capacity is incorrect.
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 58075 The specified serial number is incorrect. Check the specified serial number. 6505 58078 The specified volume does not exist or is unusable. Check the status of the specified volume. W 6505 58079 The specified primary data volume cannot be used as a secondary volume due to the settings of Volume Retention or Data Retention.
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 58093 The specified primary data volume is already registered in another journal. Identify the journal where the specified primary data volume is registered. W 6505 58094 The specified primary data volume Identify the journal where the specified cannot be deleted because the volume primary data volume is registered. is already registered in another journal.
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message Recommended Action Severity Level Access Journal Z to the remote storage system. 6505 58106 The operation failed because the specified data volumes were in one of the following status: Confirm the following items about the specified primary data volume and secondary data volume.
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 58272 A Concurrent Copy operation is in Check the status of the specified progress on the specified secondary data secondary data volume. volume. W 6505 58273 Either of the following settings is set to Use Volume Security for Mainframe to the specified secondary data volume by check the status of the specified the Volume Security for Mainframe secondary data volume.
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 58286 The command was rejected because the Check the command parameters. command was issued to the primary data volume. The command is supposed to be issued to the secondary data volume. W 6505 58287 The command was rejected because the Check the command parameters. command was issued to the secondary data volume.
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 58298 The specified secondary data volume is Check whether the specified secondary used by Concurrent Copy, Compatible data volume is used by Concurrent XRC or another program product.
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 58329 The operation of Add Pair (Paircreate) or Resume Pair (Pairresync) cannot be performed, because the data are remained in the journal cache for the master journal. Please contact HP Technical Support. E 6505 58333 The parameter related to the inflow cannot be changed, because the specified journal is a restore journal. Check the attribute of the specified journal.
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message Recommended Action 6505 58345 The Add Pair (Paircreate) operation failed due to one of the following reasons: Be sure that IO suppression mode of the W specified secondary data volume is enabled on the Universal Volume Mgr window. If the IO suppression mode is disabled, check the microcode version of DKCMAIN of the secondary storage system, and contact HP Technical Support.
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message Recommended Action Severity Level Check if the specified primary data volume is used by any of the following program products: W • A Thin Provisioning volume used as a P-VOL of Business Copy. • A Thin Provisioning volume and a source volume of Auto LUN. • A Thin Provisioning volume used as a P-VOL of Snapshot. 6505 58354 The specified primary data volume is used by another program product.
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 58485 The Add Pair (Paircreate) operation failed because the specified primary data volume was one of the following: Confirm the state of the specified primary W data in the Snapshot window. • the specified volume was a P-VOL of Snapshot and was in Reverse Copy status. • the specified volume was an S-VOL of Snapshot.
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message 6505 58510 The Add Pair (Paircreate) operation failed. Recommended Action Severity Level Check the mirror ID assigned to the W specified primary data volume number The combination of the specified primary (LDKC:CU:LDEV) from the secondary storage system, and assign a mirror ID data volume number (LDKC:CU:LDEV) that is not used, and retry the operation.
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message Recommended Action Severity Level The specified volumes or the volumes in Device window. If this operation is the specified journal were deleted. unavailable to do, please contact HP However, the blockade of the volumes Technical Support. failed. 6505 58563 The specified volume cannot be registered because the volume has failed to recover from blockade. Please retry the operation. Retry the operation.
Table 56 Error codes (part code 6505) (continued) 210 Part Code Error Number Error Message Recommended Action 6505 58595 The Paircreate operation failed because Confirm that the Continuous Access W the Continuous Access Journal function Journal function of the secondary storage of the secondary subsystem does not system supports LUSE volumes. support LUSE volumes.
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 58609 The timer type cannot be changed, Check if the specified journal belongs to W because the specified journal belongs to an extended consistency group (EXCTG). an extended consistency group (EXCTG). 6505 58610 The parameter specified in the extended Refresh the window, then retry the W consistency group (EXCTG) operation is operation.
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 58625 Journals cannot be added to the Check if the specified journal is being extended consistency group (EXCTG), used by other program product you are because the specified journals are being using. used by another program product. 6505 58627 The specified operation failed because Check the status of the command device.
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message Recommended Action Severity Level Swapping when it is referenced from the RAID Manager or Business Continuity Manager. 6505 58686 The specified operation failed, because Check the attribute of the journal of the the attribute of the journal of the remote remote storage system. storage system was not "restore.
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message Recommended Action Severity Level then retry the operation with another command device. 6505 58696 The specified volume cannot be used as Check the I/O suppression mode of the W a journal volume because the volume is specified volume. an external volume to which the I/O suppression mode is enabled. 6505 58697 The journal volume cannot be deleted from the specified journal due to the mirror status.
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message Recommended Action 6505 58705 The Delta resync operation failed. The Check the status of the specified specified secondary data volume should secondary data volume. meet the following requirements. Severity Level W • The specified volume is a secondary data volume of another mirror. • The pair status of the specified volume is PSUS, PSUE, Suspend, PAIR or Duplex.
Table 56 Error codes (part code 6505) (continued) Part Code 6505 6505 Error Number 58719 58721 Error Message Recommended Action The related program products are: The related program products are: • Continuous Access Synchronous or Continuous Access Synchronous Z • Continuous Access Synchronous or Continuous Access Synchronous Z • Continuous Access Journal or Continuous Access Journal Z • Continuous Access Journal or Continuous Access Journal Z The licensed capacity of Continuous Access Synchro
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 66594 The number of digits of LDEV (P-VOL) is invalid. Check the contents of the spreadsheet. W 6505 66595 The format of LDEV (P-VOL) is invalid. Check the contents of the spreadsheet. W 6505 66596 The value entered as LDEV (P-VOL) is outside the setting range. Check the contents of the spreadsheet.
Table 56 Error codes (part code 6505) (continued) 218 Part Code Error Number Error Message 6505 66619 The value entered as LDKC (paired VOL) Check the contents of the spreadsheet. is outside the setting range. W 6505 66620 The value of LDKC (paired VOL) is not supported. Check the contents of the spreadsheet. W 6505 66621 The number of digits of CU (paired VOL) Check the contents of the spreadsheet. is invalid. W 6505 66622 The format of CU (paired VOL) is invalid.
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 66645 The number of digits of PathGroup is invalid. Check the contents of the spreadsheet. W 6505 66646 The format of PathGroup is invalid. Check the contents of the spreadsheet. W 6505 66647 The value entered as PathGroup is outside the setting range. Check the contents of the spreadsheet. W 6505 66648 The number of digits of ResyncMode is invalid.
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 66671 The value entered as SuspendMode is outside the setting range. Check the contents of the spreadsheet. W 6505 66672 The number of digits of CFW is invalid. Check the contents of the spreadsheet. W 6505 66673 The format of CFW is invalid. Check the contents of the spreadsheet.
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message Recommended Action Severity Level The LDKC number of the specified number of the restore journal are the secondary data volume is different from same. the LDKC number of the specified restore journal. 6505 68008 The Add Pair (Paircreate) operation failed because the capacity of shared memory of the primary subsystem was insufficient. Check the capacity of shared memory of the primary subsystem.
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message Recommended Action 6505 68026 The specified secondary data volume is Install the Continuous Access Journal used as a pair volume of Continuous 3DC & 4x4 Open Mainframe function Access Synchronous, External Storage in the secondary storage system. Access Manager, or Continuous Access Synchronous Z.
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message 6505 68784 The Pairresync operation failed because The master journal group of the specified W the specified primary data volume was primary data volume runs on the 2DC one of the following. configuration in which the Continuous Access Synchronous or External Storage • The volume was not used by Access Manager cooperates. Continuous Access Synchronous or External Storage Access Manager.
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message Recommended Action Severity Level volume or Thin Provisioning Z volume that was specified as the secondary data volume was being initialized. 6505 68850 The operation failed, because the Specify “Mirror” for the [Range], then consistency (CT) group of specified data retry the operation. volume was being shared with multiple primary and secondary storage systems, and “LU” was specified for the [Range].
Table 56 Error codes (part code 6505) (continued) Part Code Error Number Error Message 6505 68886 The operation failed, because the remote Confirm whether the remote storage W storage system did not support the system supports the specified operation. specified operation. 6505 68887 The operation failed, because the specified primary data volume was as follows: • This volume was used as T-VOL of Compatible FlashCopy.
Part code 6507 Table 57 Error codes (part code 6507) Part Code Error Number Error Message Recommended Action Severity Level 6507 5036 Two or more commands which were not Check the settings, and retry the able to be processed were demanded. operation. W 6507 6012 An error occurred during SVP processing. If the problem persists despite retrying, please contact HP Technical Support. E 6507 6036 An error occurred during SVP processing.
Table 58 Error codes (part code 6510) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6510 9009 The export is complete. Click [OK]. i 6510 9021 The Port Setting process has not To continue processing, click [Yes]. If the i completed. Do you want to continue for processing finishes, reconfigure the port other ports? that is not in operation.
Table 58 Error codes (part code 6510) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6510 9118 Please check the specified value. To apply this setting, click [OK]. If you want to change the setting, click [Cancel]. i 6510 9119 No graph item has been selected. Please Select a graph item. select a graph item. 6510 9120 The graph will be closed if you execute the processing.
Table 58 Error codes (part code 6510) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6510 55039 You are specifying "Mirror" for the range Check the range setting. If you specify and trying to manipulate the same "Mirror," select only one data volume mirror. Select only one data volume pair pair in the mirror. in the mirror when you specify "Mirror" for the range. W 6510 55202 The specified controller ID cannot be used.
Table 58 Error codes (part code 6510) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6510 59008 Are you sure you want to delete the paths of the specified subsystem? To delete the specified path, click [OK]. W Otherwise, click [Cancel]. 6510 59009 Since the number of preview data Click [OK]. Apply the preview data to exceeded the maximum, the excess data the storage system, then retry the were discarded. No more preview data operation. can be stored.
Table 58 Error codes (part code 6510) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6510 59103 There is no volume that can be registered Create a volume that can be used as a W or deleted. journal volume. To do this, add a volume or use some other way. 6510 59104 The specified parity group does not contain volumes that can be registered or deleted as journal volumes.
Table 58 Error codes (part code 6510) (continued) Part Code Error Number Error Message Recommended Action Severity Level Check the status of the specified master journal. 6510 59328 The journal volume cannot be deleted, Change the status of mirror of the journal W because the attribute of mirror for the to "Initial," then retry the operation. journal is "master" and the status of the mirror is "Hold" or "Holding.
Table 58 Error codes (part code 6510) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6510 69018 There are two or more LDKC numbers Check the LDKC number for the specified W for the specified data volume. In this data volume, and specify only one LDKC operation, please specify only one LDKC number. number. 6510 69019 The number of data volumes exceeds the Check whether the specified volume is maximum. a LUSE volume. Also, check storage system’s microcode version.
Table 59 Error codes (part code 6610) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6610 9021 The Port Setting process has not To continue processing, click [Yes]. If the i completed. Do you want to continue for processing finishes, reconfigure the port other ports? that is not in operation. 6610 9024 Are you sure you want to exchange the specified ports? Please confirm the associated channel paths are off-line.
Table 59 Error codes (part code 6610) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6610 9118 Please check the specified value. To apply this setting, click [OK]. To change the setting, click [Cancel]. i 6610 9119 No graph item has been selected. Please Select a graph item. select a graph item. 6610 9120 The graph will be closed if you execute the processing.
Table 59 Error codes (part code 6610) (continued) Part Code Error Number Error Message Recommended Action 6610 55039 You are specifying "Mirror" for the range Check the range setting. If you specify and trying to manipulate the same "Mirror," select only one data volume mirror. Select only one data volume pair pair in the mirror. in the mirror when you specify "Mirror" for the range. W 6610 55202 The specified controller ID cannot be used.
Table 59 Error codes (part code 6610) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6610 59009 Since the number of preview data Click [OK]. Apply the preview data to exceeded the maximum, the excess data the storage system, then retry the were discarded. No more preview data operation. can be stored. 6610 59010 WARNING: 6610 59011 Are you sure you want to output the %s file? 6610 59013 The specified file already exists.
Table 59 Error codes (part code 6610) (continued) Part Code Error Number Error Message Recommended Action Severity Level Continuous Access Journal, then start the Continuous Access Journal Z window or the Continuous Access Journal window. 6610 59043 The number of journal volumes in some journals exceeds the maximum. Adjust the number of journal volumes. 6610 59100 The same volume is stored more than once in the Preview list.
Table 59 Error codes (part code 6610) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6610 59151 The current microcode version of To use a mainframe volume as a journal W DKCMAIN only supports OPEN-V as the volume, please contact HP Technical emulation type of a journal volume. Support to update the microcode version of DKCMAIN.
Table 59 Error codes (part code 6610) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6610 59332 A multiplatform volume is included in the Confirm whether the specified volume is W specified volumes. a multiplatform volume. Also, confirm the version of the microcode of the storage The Add Pair operation cannot be performed using multiplatform volumes. system. 6610 59335 The value of the path watch time is not entered or is outside the range.
Part code 6805 Table 60 Error codes (part code 6805) Part Code Error Number Error Message Recommended Action Severity Level 6805 5099 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 6805 6012 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 6805 6023 The SVP is busy. Please wait for a while, and then retry the operation.
Table 60 Error codes (part code 6805) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6805 55214 The Level 2 Threshold setting is incorrect. Correct the setting, then retry. If the same W problem persists despite retrying, please contact HP Technical Support. 6805 55215 The Level 1 SIM setting is incorrect. 6805 55216 The Level 2 Suspend setting is incorrect. Correct the setting, then retry.
Table 61 Error codes (part code 6810) (continued) Part Code Error Number Error Message Recommended Action Severity Level 6810 55212 The options "Block Option" and "Do not Correct the setting, then retry. If the same W Block (Volume Level)" cannot be problem persists despite retrying, please specified at the same time. contact HP Technical Support. 6810 55214 The Level 2 Threshold setting is incorrect. Correct the setting, then retry.
9 Message (part code group 7nnn) This chapter includes the error messages with the part code 7005 to 7110. Part code 7005 Table 62 Error codes (part code 7005) Part Code Error Number Error Message Recommended Action Severity Level 7005 5013 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 7005 5099 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 62 Error codes (part code 7005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 7005 8502 You cannot reserve the volume, because Delete the Remote Copy pair. a remote copy pair exists in the same subsystem frame. W 7005 8503 You cannot create the new pair, because Delete the Remote Copy pair. a remote copy pair exists in the same subsystem frame. W 7005 8504 The command was rejected. Check the composition, the status, or the volume status of the pair.
Table 62 Error codes (part code 7005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 7005 8519 Volumes specified as P-VOL and S-VOL, or those constituting LUSE are not consistent in capacity. Select volumes with the same capacity. W When specifying LUSE volumes as P-VOL and S-VOL, the capacity of each volume constituting the LUSE volumes must be the same. 7005 8520 You cannot set a pair, because the volume type is different for each.
Table 62 Error codes (part code 7005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 7005 8541 There is sufficient shared memory to create 4096 pairs, and the initial subsystem setup is complete. Close the message box. i 7005 8542 Failed to complete the initial shared memory setup. Please contact HP Technical Support. E 7005 8543 The shared memory size is different. Please contact HP Technical Support.
Table 62 Error codes (part code 7005) (continued) Part Code Error Number Error Message 7005 8560 This volume cannot be specified because Specify a volume that is not used as a it is used as a command device. command device. W 7005 8561 The command code is invalid. Please contact HP Technical Support. E 7005 8562 The command code sender is invalid. Please contact HP Technical Support. E 7005 8563 The volume type is invalid. Check the contents, and retry.
Table 62 Error codes (part code 7005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 7005 8584 No volume is defined as a reserved volume. Check the contents, and retry. W 7005 8585 The number of reserved volumes exceeds Stop the operation of the Reserve volume W the maximum. setting, or delete the Reserve volume. 7005 8586 The number of groups that can be set in Check the contents, and retry. the same subsystem is invalid.
Table 62 Error codes (part code 7005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 7005 8606 The operation to create L2 pair has been rejected, because the P-VOL of L1 pair is used as the P-VOL of Continuous Access Synchronous pair or External Storage Access Manager pair. When the P-VOL of L1 pair is used as W the P-VOL of Continuous Access Synchronous pair or External Storage Access Manager pair, L2 pair cannot be created.
Table 62 Error codes (part code 7005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 7005 8623 The command has been rejected, because the specified volume is used as S-VOL of Continuous Access Synchronous or External Storage Access Manager pair. The S-VOL of Continuous Access W Synchronous or External Storage Access Manager pair cannot be used as a reserved volume. Specify another volume.
Table 62 Error codes (part code 7005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 7005 8642 The command has been rejected, because the specified S-VOL is shared as the P-VOL of the other pair and the pair is in the COPY(RS-R) status. Wait until the status of the pair sharing the P-VOL becomes PAIR, then retry the operation. W The Pairresync operation has been rejected, because the specified pair is not in the state of PSUS.
Table 62 Error codes (part code 7005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 7005 8657 The Swap&Freeze option cannot be specified, because the mode 80 is on. Please contact HP Technical Support. E 7005 8670 The number of volumes composing the LUSE volume specified as the P-VOL does not match the number of volumes composing the LUSE volume specified as the S-VOL.
Table 62 Error codes (part code 7005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 7005 57101 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 7005 57102 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 62 Error codes (part code 7005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 7005 58299 The operation failed because the specified P-VOL was a data volume of Continuous Access Journal. Check the requirements for using the volume with Continuous Access Journal. Check the requirements for using the W volume with Continuous Access Journal. 7005 58300 The operation failed, because the specified S-VOL was a data volume of Continuous Access Journal.
Table 62 Error codes (part code 7005) (continued) Part Code Error Number Error Message Recommended Action 7005 58492 The Pairsplit-S operation has failed. Check the configuration. Refresh the window, and check whether W the pair exists. 7005 58493 The PCB required for this operation is not mounted. Check the subsystem configuration. Mount the required PCB, then retry the operation. E 7005 58520 The operation failed, because different versions of microcodes coexisted in the disk subsystem.
Table 62 Error codes (part code 7005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 7005 58585 The operation failed because the CU group of the specified volume is not supported. Volumes that do not belong to CU group W 0 are currently not supported. Specify another volume. 7005 58630 The operation failed because the specified P-VOL was used by Delta resync of Continuous Access Journal.
Table 62 Error codes (part code 7005) (continued) Part Code Error Number Error Message Recommended Action Severity Level composed of the Thin Provisioning volume and the volumes other than Thin Provisioning volume. 7005 68755 The Quick Restore command has been rejected, because device information (Inquiry information) of P-VOL and S-VOL was different in the specified pair. 7005 68760 Quick Restore cannot be executed, Wait for a while, then retry the because the configuration is being operation.
Table 62 Error codes (part code 7005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 7005 68868 The command has been rejected, because the volume specified as S-VOL is a quorum disk. Specify another volume. W 7005 68869 The command has been rejected, because the volume specified as the reserved volume is a quorum disk. Specify another volume.
Table 62 Error codes (part code 7005) (continued) Part Code Error Number Error Message Recommended Action 7005 75005 The command was rejected, because no Set an LU path to the specified P-VOL, LU path was set to the volume specified then retry the operation. as P-VOL. W 7005 75006 The command was rejected, because no Set an LU path to the specified P-VOL, LU path was set to the volume specified then retry the operation. as S-VOL.
Part code 7010 Table 64 Error codes (part code 7010) Part Code Error Number Error Message Recommended Action Severity Level 7010 5115 The volume of S-VOL is different from specified P-VOL. Check the capacity of P-VOL and S-VOL. W Specify a volume with the same capacity, and retry the operation. 7010 5116 You cannot create another L1 pair, You cannot create L1 pair for the because the number of L1 pairs exceeds specified P-VOL. Delete the created L1 the maximum. pair, and retry the operation.
Table 64 Error codes (part code 7010) (continued) Part Code Error Number Error Message Recommended Action 7010 8658 Some settings could not be applied normally. Refer to the error code. Check the error code in the Preview list. W 7010 8659 The PCB required for this operation is not mounted. Check the subsystem configuration. Mount the required PCB, then retry the operation. 7010 9002 The requested operation has completed. The operation ended normally. Execute the next operation.
Table 64 Error codes (part code 7010) (continued) Part Code Error Number Error Message Recommended Action Severity Level for Pairsplit operation or Snapshot pair is included in the specified pairs. from Remote Web Console, if the specified pair is a Snapshot pair. Part code 7105 Table 65 Error codes (part code 7105) Part Code Error Number Error Message Recommended Action Severity Level 7105 5099 An error occurred during SVP processing.
Table 65 Error codes (part code 7105) (continued) Part Code Error Number Error Message Recommended Action Severity Level pairs and the commands that can be accepted. 7105 8506 The command has been rejected, Vary the T-VOL or the reserved volume because the specified T-VOL or reserved offline from the mainframe host, then volume is used by the host. issue the command again. 7105 8507 The Split Pair command was issued to the pairs in the split status.
Table 65 Error codes (part code 7105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 7105 8526 An internal logic error occurred. Please contact HP Technical Support. E 7105 8527 An internal logic error occurred. Please contact HP Technical Support. E 7105 8528 An internal logic error occurred. Please contact HP Technical Support. E 7105 8529 An internal logic error occurred. Please contact HP Technical Support.
Table 65 Error codes (part code 7105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 7105 8549 The S-VOL is not implemented. You cannot execute the operation for the W volume which is not implemented. 7105 8550 The command has been rejected, because the specified S-VOL is blocked or used as a system disk. • Restore the blocked volume, then retry E the operation. Wait until the volume is formatted, and retry the operation.
Table 65 Error codes (part code 7105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 7105 8569 The command has been rejected, See the section "Planning number of W because the area of the differential table pairs" in the HP P9000 Business Copy or pair table to set pairs is insufficient. for Mainframe Systems User Guide for the relation between the number of pairs that can be created and the shared memories. 7105 8570 The selected volume does not exist.
Table 65 Error codes (part code 7105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 7105 8591 The specified pair is already set in another group. Check the contents, and retry. W 7105 8592 The command was rejected because the Check the capacity of the installed licensed capacity was exceeded. license key. To create more pairs, purchase a license key for larger capacity. W 7105 8593 The S-VOL is a source volume for Auto LUN. Release the Auto LUN setting.
Table 65 Error codes (part code 7105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 7105 8609 The specified volume is not set as a reserved volume. Check the status of the volume. W 7105 8610 The T-VOL is a target volume for Auto LUN. Release the Auto LUN setting. W 7105 8611 The specified volume is a T-VOL. Check the status of the volume. W 7105 8612 The specified volume is not a T-VOL. Check the status of the volume.
Table 65 Error codes (part code 7105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 7105 8631 The specified CU number is invalid. Please contact HP Technical Support. W 7105 8632 The timing of issuing the command is invalid. Please contact HP Technical Support. E 7105 8633 The abnormal status is invalid. Please contact HP Technical Support.
Table 65 Error codes (part code 7105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 7105 8649 Because the boot device is the T-VOL in Check the specified volume number. the Delete Pair command, the flag does not match. W 7105 8650 The boot device and the S-VOL do not Check the specified volume number. match in the Add Pair, Resync, or Delete Pair command. W 7105 8651 The SSID is invalid. Check the contents, and then retry.
Table 65 Error codes (part code 7105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 7105 8991 The command has been rejected, because the Compatible FlashCopy relationship exists. Withdraw the Compatible FlashCopy relationship. W 7105 8992 The command has been rejected, because sufficient amount of shared memory is not installed. Install additional shared memory.
Table 65 Error codes (part code 7105) (continued) Part Code Error Number Error Message Recommended Action 7105 58259 The Quick Restore command has been rejected, because the specified pair contains external volumes, and also is used as a Remote Copy pair. Delete the Remote Copy pair or execute W the operation by other pairs. 7105 58260 The command has been rejected, because the specified S-VOL is used as M-VOL of Continuous Access Synchronous Z pair.
Table 65 Error codes (part code 7105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 7105 58533 The operation failed, because the specified S-VOL was a journal volume. Release the journal volume setting or specify another volume. W 7105 58534 The operation failed, because the specified T-VOL was a journal volume. Release the journal volume setting or specify another volume.
Table 65 Error codes (part code 7105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 7105 68747 The command has been rejected because the FICON(R) Data Migration source volume is used in the specified pair, and T-VOL is used by one of the following program products: Cancel the setting where the T-VOL is W used by the other program products, and then retry the operation.
Table 65 Error codes (part code 7105) (continued) Part Code Error Number Error Message Recommended Action is a FICON(R) Data Migration Source Volume. configuration. Specify volumes other than FICON(R) Data Migration Source Volume for S-VOL, and then retry the operation. Severity Level 7105 68776 The command has been rejected because the T-VOL of the specified pair is a FICON(R) Data Migration Source Volume. The specified operation cannot be W executed in the current pair configuration.
Table 65 Error codes (part code 7105) (continued) Part Code Error Number Error Message 7105 75004 The command was rejected, because the Associate the specified Thin Provisioning W Thin Provisioning Z volume specified as Z volume with a pool, and then retry the a reserved volume was not associated operation. with a pool. 7105 75015 The specified LDEV cannot be used because the user has no access right to a resource group to which the LDEV belongs.
Table 65 Error codes (part code 7105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 7105 78121 The operation failed because the Specify another volume. specified S-VOL was used by Compatible FlashCopy SE, or was a TSE volume. W 7105 78122 The operation failed because the specified T-VOL was a TSE volume. Specify another volume. W 7105 78123 The operation failed because the specified reserved volume was a TSE volume. Specify another volume.
Table 66 Error codes (part code 7110) (continued) Part Code Error Number Error Message Recommended Action Severity Level normal condition, and then retry the operation. necessary, please contact HP Technical Support. 7110 8534 An internal logic contradiction occurred. Please contact HP Technical Support. E 7110 8568 The emulation type is invalid. Specify the volume of the supported emulation type. i 7110 8658 Some settings could not be applied normally. Refer to the error code.
Table 66 Error codes (part code 7110) (continued) Part Code Error Number Error Message Recommended Action Severity Level Do you want to continue this operation? 7110 65662 The data has been changed. The settings To continue processing, click [OK]. will be discarded if you continue the Otherwise, click [Cancel]. processing.
10 Message (part code group 8nnn) This chapter includes the error messages with the part code 8005 to 8809. Part code 8005 Table 67 Error codes (part code 8005) Part Code Error Number Error Message Recommended Action Severity Level 8005 2002 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 8005 2015 A communication error has occurred. Retry the same operation.
Table 67 Error codes (part code 8005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 8005 7060 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 8005 7111 The storage system is in the internal Wait, then click [Refresh]. process, or some other user is changing the configuration. E 8005 8001 An error occurred while connecting to the subsystem. Wait, then retry the operation.
Table 67 Error codes (part code 8005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 8005 65783 There are functions that cannot change Confirm the setting status of the current E the system disk option due to one of the system disk option. For the functions that following reasons: could not be set, add a system disk or restore the blocked system disk, then • The system disk capacity is retry the operation. insufficient. • The system disk is blocked.
Table 68 Error codes (part code 8105) (continued) Part Code Error Number Error Message Recommended Action Severity Level for Remote Copy, Business Copy, Auto LUN, or Snapshot. 8105 1009 The emulation type of the volumes is not The configuration information has been W for open systems, or the volumes are not changed already. Check the settings, mounted. and request the configuration information setting again. 8105 1010 An error occurred during SVP processing.
Table 68 Error codes (part code 8105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 8105 1067 You are trying to register the same host group as the existing one. The configuration information has been W changed already. Check the settings, and request the configuration information setting again. 8105 1068 The specified host group has not been registered. The configuration information has been W changed already.
Table 68 Error codes (part code 8105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 8105 1128 An error occurred. If this problem persists, please contact HP Technical Support. Check the setting(s), then retry the operation. W 8105 1130 The specified name is the same as the Correct the specified contents, and system default name. Please change the request again. name.
Table 68 Error codes (part code 8105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 8105 1353 S-VOLs remain on the Fibre-RCU port. This operation may cause a fatal damage to S-VOLs. Please stop this operation. If you want to continue this operation, please remove the S-VOLs from the RCU port first. Since the port you are trying to set is for W Remote Copy, you must delete the S-VOL logical path that is set to RCU Target, then retry the port setting.
Table 68 Error codes (part code 8105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 8105 1926 The path cannot be set to the specified volume, because the volume is being used as a quorum disk. Check the setting. W 8105 1927 The specified volume cannot be set as a Check the setting. command device, because it is being used as a quorum disk.
Table 68 Error codes (part code 8105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 8105 2205 Devices to be maintained include journal Delete all pairs to which the journal volumes. volumes belong. W 8105 2504 No settings can be made because of a volume reserved for RAID Manager. W 8105 2510 No path can be set to the specified Please contact HP Technical Support and W volume because the addition of volumes finish adding volumes. is not finished.
Table 68 Error codes (part code 8105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 8105 5030 The spreadsheet has not been changed at all. Change the configuration at least one line in the spreadsheet. W 8105 5060 The length of the character string is invalid. One line can have up to 127 characters. E 8105 5061 The number of lines is invalid. The CSV file can have up to 70,000 lines. E 8105 5062 The size of the CSV file is invalid.
Table 68 Error codes (part code 8105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 8105 5744 The command device security switch cannot be turned on because this is not command device. Turn on the command device switch. W 8105 5745 The security switch on the port is off. Turn Turn on the security switch on this port. on the switch. W 8105 5746 The group ID is invalid. Correct the group ID. W 8105 5747 The group cannot be added.
Table 68 Error codes (part code 8105) (continued) Part Code Error Number Error Message 8105 5786 The path can be defined only for the A, Correct the name of port. E, J or N port. W 8105 5789 The intermediate volume cannot be specified as a command device. W 8105 5790 A program error occurred under internal If nothing changes despite retrying, process. please contact HP Technical Support.
Part code 8107 Table 69 Error codes (part code 8107) Part Code Error Number Error Message Recommended Action Severity Level 8107 5641 The number of lines exceeds the maximum number of lines of a spreadsheet. Check the setting. W 8107 5642 The number of characters exceeds the maximum number of characters of a spreadsheet. Check the setting. W 8107 5643 A time-out error occurred.
Table 70 Error codes (part code 8110) (continued) Part Code Error Number Error Message Recommended Action Severity Level 8110 5775 A file access error occurred. Correct the specified contents, and retry W the operation. 8110 5776 The file type is invalid. Please select the file with the extension "*.spd". Correct the specified contents, and retry W the operation. 8110 7060 An error occurred during processing.
Part code 8305 Table 73 Error codes (part code 8305) Part Code Error Number Error Message Recommended Action Severity Level 8305 56524 This function cannot be used by the storage partition administrator. Please contact HP Technical Support. E Part code 8505 Table 74 Error codes (part code 8505) Part Code Error Number Error Message Recommended Action Severity Level 8505 2007 An error occurred during SVP processing.
Table 74 Error codes (part code 8505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 8505 55012 An invalid SLPR Name was detected. SLPR No:%s Please contact HP Technical Support. E 8505 55013 Invalid login information was detected. SLPR No:%s Please contact HP Technical Support. W 8505 55014 This name is already used as the CLPR name. Assign a different CLPR name, and then W retry the operation.
Table 74 Error codes (part code 8505) (continued) Part Code Error Number Error Message Recommended Action Severity Level problem persists, please contact HP Technical Support. 8505 55027 The cache size is incorrect. CLPR No:%s 8505 55028 The specified cache size excluding the cache residency size is less than the minimum required. CLPR No:%s Correct the cache size setting, and then W retry the operation. If the problem persists, please contact HP Technical Support.
Table 74 Error codes (part code 8505) (continued) Part Code Error Number Error Message Recommended Action Severity Level intended CLPR is too high. Please wait until the write pending rate falls, and then retry the operation. 8505 58313 The configuration cannot be changed Check the Cache Residency size and the W because the available Cache Residency number of Cache Residency areas. size or the number of Cache Residency areas in the intended CLPR is insufficient.
Part code 8507 Table 75 Error codes (part code 8507) Part Code Error Number Error Message Recommended Action Severity Level 8507 6012 An error occurred during SVP processing. If the same problem persists despite retrying, please contact HP Technical Support. E 8507 7070 An error occurred during SVP processing. If the same problem persists despite retrying, please contact HP Technical Support. E 8507 7071 An error occurred during SVP processing.
Table 76 Error codes (part code 8510) (continued) Part Code Error Number Error Message Recommended Action 8510 55262 The Parity Group cannot be migrated to Apply the tentative settings with no parity W the CLPR that you newly created. Please groups to the CLPR that you have apply the tentative settings with no parity created, then migrate the parity group. groups to the CLPR that you have created, and then migrate the parity group.
Part code 8605 Table 77 Error codes (part code 8605) Part Code Error Number Error Message Recommended Action Severity Level 8605 6012 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. If this problem persists, please contact HP Technical Support. E 8605 6022 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. If this problem persists, please contact HP Technical Support.
Table 78 Error codes (part code 8610) (continued) Part Code Error Number Error Message Recommended Action Severity Level When the mail notification service is enabled, destination e-mail address is required to input. 8610 65761 The IP address of the mail server is Enter the IP address or the host name. invalid. Check the value if it is set as one of the following. W IPv4: • The value of each class is other than 0 to 255. • The value of Class A or all classes is 0. • There is a blanked class.
Table 79 Error codes (part code 8805) (continued) Part Code Error Number Error Message Recommended Action Severity Level 8805 6024 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support E 8805 6036 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 8805 6091 An error occurred while compressing a file. If the same problem persists despite retrying, please contact HP Technical Support.
11 Message (part code group 9nnn) This chapter includes the error messages with the part code 9005 to 9610. Part code 9005 Table 81 Error codes (part code 9005) Part Code Error Number Error Message Recommended Action Severity Level 9005 5013 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 9005 5040 The number of requests exceeds the Reduce the number of requests, and then W maximum number that can be processed. retry the operation.
Table 81 Error codes (part code 9005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 9005 8102 This function is not supported. Check the DKC-MAIN version. W 9005 8103 The subsystem status is invalid. Please contact HP Technical Support. Check the DKC-MAIN version. E 9005 8659 No PCBs for mainframe computers are installed. Install PCBs for mainframe computers, then retry the operation.
Table 83 Error codes (part code 9010) (continued) Part Code Error Number Error Message Recommended Action Severity Level 9010 65703 The maximum permissible capacity of Install additional license key(s) to expand W program product became insufficient. the license capacity of this software title. Please install additional license key(s) to expand the license capacity of this software title. 9010 79003 The used capacity is being calculated now.
Table 84 Error codes (part code 9105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 9105 6012 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. An error occurred during the SVP processing. If this problem persists, please contact HP Technical Support. E 9105 6023 The file operation failed. Please contact HP Technical Support.
Part code 9107 Table 85 Error codes (part code 9107) Part Code Error Number Error Message Recommended Action Severity Level 9107 6012 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 9107 7060 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 86 Error codes (part code 9110) (continued) Part Code Error Number Error Message Recommended Action Severity Level 9110 5621 No item is selected. Please select an item. Click [OK], select an item, and retry the W operation. 9110 5622 If you want to continue this operation, please select only one line. Click [OK], select only one line, and retry W the operation. 9110 5623 The data has been changed. If you select To continue processing, click [OK].
Table 86 Error codes (part code 9110) (continued) Part Code Error Number Error Message Recommended Action Severity Level information are set to offline, and then select [Yes]. 9110 56538 No volume is registered on the LDEV Delete all LDEV groups and register LDEV W group because the volume configuration groups and Security groups again. has been changed. Please delete all LDEV groups and register LDEV groups and Security groups again.
Table 87 Error codes (part code 9205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 9205 7060 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 9205 7111 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. If this problem persists, please contact HP Technical Support. E 9205 7310 This error code is not registered.
Table 87 Error codes (part code 9205) (continued) Part Code Error Number Error Message Recommended Action 9205 66005 The spreadsheet declaration statement Check the contents of the Volume or the definition statement is not entered Retention spreadsheet. in the spreadsheet file. W 9205 66006 The number of data items entered in the Check the contents of the Volume spreadsheet has exceeded the limit. Retention spreadsheet.
Table 88 Error codes (part code 9210) (continued) Part Code Error Number Error Message Recommended Action Severity Level 9210 8112 There is no valid volume. Mount volumes, then retry the operation. W 9210 9107 The value that is under setup is not reflected yet. Do you want to continue the operation? To continue processing, click [OK]. To stop processing, click [Cancel].
Table 89 Error codes (part code 9605) (continued) 314 Part Code Error Number Error Message Recommended Action Severity Level 9605 8120 The specified logical volume does not exist. Specify an open-system volume. W 9605 8122 This logical volume is busy. Retry a little later. W 9605 8123 This function is not supported. Check if the DKCMAIN and SVP microcode versions are mismatched. E 9605 8124 This logical volume is a mainframe volume. Specify an open-system volume.
Table 89 Error codes (part code 9605) (continued) Part Code Error Number Error Message Recommended Action Severity Level 9605 8156 You cannot change the access attribute because the expiration lock is set to Enable. Set the expiration lock to Disable, then change the access attribute. W 9605 58404 The specified operation cannot be executed because the LDEV shredding or the LDEV format is being executed. Retry the operation after the process is completed.
Table 89 Error codes (part code 9605) (continued) Part Code Error Number Error Message Recommended Action 9605 68002 This logical volume cannot be selected Check the logical volume configuration, W because it is used as a volume for System then retry the operation. Disk. 9605 75015 The specified LDEV cannot be used because the user has no access right to a resource group to which the LDEV belongs. 9605 76514 The setting operation cannot be done Verify the available LDEVs.
12 Message (part code group 10nnn) This chapter includes the error messages with the part code 10010 and 10122. Part code 10010 Table 91 Error codes (part code 10010) Part Code Error Number Error Message Recommended Action Severity Level 10010 55011 0 cannot be specified in all the fields or Reply to the message. the Class A field. W 10010 55638 The same IP address, user ID and output Reply to the message. folder are set to the primary FTP server and the secondary FTP server.
Part code 10122 Table 93 Error codes (part code 10122) 318 Part Code Error Number Error Message Recommended Action 10122 105194 An error occurred while formatting. Retry the operation. If the same problem E persists despite retrying, please contact HP Technical Support. 10122 105195 An error occurred while preparing the quick format. Retry the operation. If the same problem E persists despite retrying, please contact HP Technical Support.
Table 93 Error codes (part code 10122) (continued) Part Code Error Number Error Message Recommended Action Severity Level If the same problem persists despite retrying, please contact HP Technical Support.
13 Message (part code group 20nnn) This chapter includes the error messages with the part code 20020 to 20825. Part code 20020 Table 94 Error codes (part code 20020) Part Code Error Number Error Message Recommended Action Severity Level 20020 107000 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 20020 107001 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 94 Error codes (part code 20020) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20020 107020 A file or a directory of the specified path Check the environment of file or directory E does not exist, or the access is rejected. of the specified path. 20020 107021 A file or a directory of the specified path Check the environment of file or directory E does not exist, or the access is rejected. of the specified path.
Table 94 Error codes (part code 20020) (continued) Part Code Error Number Error Message 20020 107042 Failed to start the session due to no user Confirm whether you are authorized. authority. E 20020 107043 Failed to save the specific information of Check the environment. user. E 20020 107044 Failed to save the specific information of Check the environment. user. E 20020 107045 Failed to save the specific information of Check the environment. user.
Table 94 Error codes (part code 20020) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20020 107059 The key store file does not exist. Check the environment. E 20020 107060 Failed to get a certificate. Check the environment. E 20020 107061 Failed to access the key store file. Check the environment. E 20020 107062 Failed to initialize the key store file. Check the environment. E 20020 107063 Failed to access the key store file.
Table 94 Error codes (part code 20020) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20020 107094 The number of onetime keys has exceeded the maximum. Wait for a while, then retry the operation. E 20020 107095 Failed to authenticate the user account. Check the environment. E 20020 107096 The specified group ID does not exist. If the same problem persists despite retrying, please contact HP Technical Support.
Table 95 Error codes (part code 20121) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20121 107023 An internal logic error occurred. If the same problem persists despite retrying, please contact HP Technical Support. E 20121 107024 A connection error has occurred. Check the internet protocol (IP) address. E If the IP address is correct, terminate the browser (also terminate the storage list browser), then log it in again.
Table 95 Error codes (part code 20121) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20121 108001 Version mismatch between the Remote Web Console and the SVP. Clear the cache of JRE and browser E being used, then restart the browser and retry the operation. When this problem persists, contact your network administrator because it might be a problem of the proxy server.
Table 96 Error codes (part code 20122) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20122 105059 The task cannot be deleted. The status of the task might be changed. W Close the window, then check the task status. 20122 105061 The task cannot be suspended. The status of the task might be changed. W Close the window, then check the task status. 20122 105063 The task cannot be restarted. The status of the task might be changed.
Table 96 Error codes (part code 20122) (continued) Part Code Error Number Error Message Recommended Action Severity Level registered in any group is not allowed to access any LUN. Do you want to continue this operation? 20122 106074 All the hosts connected to the target ports To continue processing, click [OK]. To are only allowed to access a LUN that stop processing, click [Cancel]. is defined in the group #00.
Table 96 Error codes (part code 20122) (continued) Part Code Error Number Error Message Recommended Action Severity Level Therefore, the execution of the tasks are following status, which can be deleted inhibited at present. without any problem. • Complete status • Failed status 20122 109015 The task could not complete execution. because the Remote Web Console stopped. Check whether the setting has been enabled, then make the setting again.
Table 97 Error codes (part code 20123) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20123 107011 Failed to get the RMI Lock. Do the following. W • This operation cannot be done while another user is changing the configuration. Wait for a while, and then retry the operation. • This operation cannot be done while a task is in progress. Wait for a while, and then retry the operation.
Table 97 Error codes (part code 20123) (continued) Part Code Error Number Error Message Recommended Action Severity Level problem persists despite retrying, please contact HP Technical Support. 20123 107024 The content of a task to be registered conflicts with that of another that has already been registered. Retry the operation. If the same problem persists despite retrying, please contact HP Technical Support.
Part code 20222 Table 98 Error codes (part code 20222) Part Code Error Number Error Message 20222 105004 The task for the operation is not selected. Select one or more table rows. 20222 105005 A task which is not in the state of suspend is in the specified task. Or, you have not a permission to operate the task status. 20222 105006 A task which is not in the state of waiting Select another task which is in the state is in the specified task. Or, you have not of waiting.
Table 98 Error codes (part code 20222) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20222 109017 {0} is completed(Request). - i 20222 109021 Check the error details with the error code from the following list. - W Part code 20305 Table 99 Error codes (part code 20305) Part Code Error Number Error Message Recommended Action Severity Level 20305 5013 An error occurred during SVP processing.
Part code 20322 Table 100 Error codes (part code 20322) Part Code Error Number Error Message Recommended Action Severity Level 20322 107001 The processing cannot continue due to an internal logic contradiction. Refresh the window, then retry the operation. E If the same problem persists despite retrying, please contact HP Technical Support.
Table 102 Error codes (part code 20520) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20520 107004 Failed to read the log preference. Check the environment. E 20520 107005 The parameter is specified incorrectly. Specify a correct value. E 20520 107006 Failed to read the preference. Check the environment. E 20520 107007 There is no report to be created. Check the environment. E 20520 107008 There is no input directory. Check the environment.
Part code 20525 Table 104 Error codes (part code 20525) Part Code Error Number Error Message Recommended Action Severity Level 20525 107001 The specified report does not exist. Specify the correct name or ID of the report. W 20525 107002 You do not have permission to execute Log in again with the user who has W the specified command. the required permission, and then retry the operation. 20525 107003 The specified parameters are incorrect. Specify the correct parameters.
Table 104 Error codes (part code 20525) (continued) Part Code Error Number Error Message Recommended Action 20525 There is no deletable report. Display a list of reports and verify W if there is any of reports that you created. 107017 Severity Level When you delete a report created by another user, you need to have permission to delete it. 20525 107018 The specified report cannot be deleted. Display a list of reports and verify W if the specified report is the one you created or not.
Table 106 Error codes (part code 20705) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20705 6022 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 20705 6533 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 20705 6537 The setting process has not been executed because there is no error in this setting, but an error in the others settings.
Table 106 Error codes (part code 20705) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20705 76112 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 20705 76113 The specified resource has already been specified. Exclude the duplicated setting, and W then retry the operation. 20705 76114 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Part code 20721 Table 107 Error codes (part code 20721) Part Code Error Number Error Message Recommended Action Severity Level 20721 105001 No table rows are selected. Select one or more table rows. W 20721 105003 No table row, or two or more table rows are selected. Select one table row. W 20721 109001 Are you sure you want to remove the selected row(s)? To continue processing, click [OK]. W To stop processing, click [Cancel].
Table 108 Error codes (part code 20722) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20722 105311 You cannot delete the resource group Release the resource group that that has been assigned to a user has been assigned to the user group. group, and then retry the operation. 20722 105315 You cannot create a resource group because an unregistered resource group has been assigned to the user group.
Table 109 Error codes (part code 20825) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20825 107006 The SVP is busy. Wait for a while, and then retry the operation. W 20825 107007 An internal logic error occurred. If this problem persists, please contact HP Technical Support. E 20825 107008 The specified command is invalid. Enter the correct command. W 20825 107009 Failed to download the specified file.
14 Support and other resources Contacting HP For worldwide technical support information, see the HP support website: http://www.hp.
• http://www.hp.com/service_locator • http://www.hp.com/support/manuals • http://www.hp.com/support/downloads • http://www.hp.
Table 110 Document conventions (continued) Convention Element Monospace text • File and directory names • System output • Code • Commands, their arguments, and argument values Monospace, italic text • Code variables • Command variables Monospace, bold text WARNING! CAUTION: IMPORTANT: NOTE: TIP: Emphasized monospace text Indicates that failure to follow directions could result in bodily harm or death. Indicates that failure to follow directions could result in damage to equipment or data.
Glossary allocation The ratio of allocated storage capacity versus total capacity as a percentage. Allocated storage refers to those logical devices (LDEVs) that have paths assigned to them. Allocated storage capacity is the sum of the storage of these LDEVs. Total capacity is the sum of the capacity of all LDEVs on the disk array. BC P9000 or XP Business Copy. An HP application that provides volume-level, point-in-time copies in the disk array. CHA Channel adapter.
P-VOL Primary volume. parity group A set of hard disk drives that have the same capacity and that are treated as one group. A parity group contains both user data and parity information, which enables user data to be accessed if one or more drives in the group is not available. path A path is created by associating a port, a target, and a LUN ID with one or more LDEVs. Also known as a LUN. PAV Parallel access volume. PCB Printed circuit board. PDEV Physical device.
Index C contacting HP, 343 conventions document, 344 storage capacity values, 344 text symbols, 345 D disk arrays supported models, 6 document conventions, 344 related information, 343 documentation HP website, 343 providing feedback, 343 H help obtaining, 343 HP technical support, 343 R related documentation, 343 S storage capacity values conventions, 344 Subscriber's Choice, HP, 343 symbols in text, 345 T technical support HP, 343 service locator website, 343 text symbols, 345 typographic conventions
