HP P9000 RAID Manager Reference Guide (T1610-96037, October 2011)

D: Checking for CHK-F3 on Write is disabled.
B =E: Checking for CHK-F3 in the data block #0 is enabled.
D: Checking for CHK-F3 in the data block #0 is disabled.
BR-W-B-Z: This column displays the flags for checking regarding CHK-F2 in the data block.
R =E: Checking for CHK-F2 on Read is enabled.
D: Checking for CHK-F2 on Read is disabled.
W =E: Checking for CHK-F2 on Write is enabled.
D: Checking for CHK-F2 on Write is disabled.
B =E: Comparing for CHK-F2 in the data block is enabled. D: Comparing for CHK-F2 in the data
block is disabled.
Z =E: The NON zero checking for CHK-F2 in the data block shows to being enabled.
D: The NON zero checking for CHK-F2 in the data block shows to being disabled.
SR-W-B-S: Displays the flags for checking regarding CHK-F1 in the data block.
R =E: Checking for CHK-F1 on Read is enabled.
D: Checking for CHK-F1 on Read is disabled.
W =E: Checking for CHK-F1 on Write is enabled.
D: Checking for CHK-F1 on Write is disabled.
B =E: Checking for CHK-F1 in the data block #0 is enabled.
D: Checking for CHK-F1 in the data block #0 is disabled.
S =E: Referring for CHK-F1 flag contained in the data block is enabled.
D: Referring for CHK-F1 flag contained in the data block is disabled.
Example 3: raidvchkdsp Command Example with the -v offset option
# raidvchkdsp -g vg01 -fd -v offset <=Example of -v offset option.
Group PairVol Device_File Seq# LDEV# Bsize STLBA ENLBA BNM
vg01 oradb1 c4t0d2 2332 2 1024 1 102400 9
vg01 oradb2 c4t0d3 2332 3 1024 1 102400 9
Output of the raidvchkdsp command with -v offset option:
Bsize: This column displays the data block size of Oracle I/O, in units of bytes.
STLBA: Displays the start of LBA on a target volume for checking, in units of 512 bytes.
ENLBA: Displays the end of LBA on a target volume for checking, in units of 512 bytes.
NOTE: If STLBA and ENLBA are both zero, this means to check all blocks.
BNM: Displays the number of bits for checking regarding CHK-F2, in units of bits. If BNM is zero,
this means the checking for CHK-F2 is disabled.
Example 4: raidvchkdsp Command Example with the -v errcnt option
# raidvchkdsp -g vg01 -fd -v errcnt <=Example of -v errcnt option.
Group PairVol Device_File Seq# LDEV# CfEC MNEC SCEC BNEC
vg01 oradb1 c4t0d2 2332 2 0 0 0 0
vg01 oradb2 c4t0d3 2332 3 0 0 0 0
Output of the raidvchkdsp command with -v errcnt option:
CfEC: Displays the error counter for checking of block size validation.
MNEC: Displays the error counter for checking of CHK-F3 validation.
SCEC: Displays the error counter for checking of CHK-F1 validation.
BNEC: Displays the error counter for checking of CHK-F2 validation.
76 Replication commands