HP P9000 RAID Manager Reference Guide (T1610-96037, October 2011)

DescriptionOption
Searches a group on the configuration definition file (local instance) for the specified raw_device,
and if the specified raw_device is contained in the group, the target volume is executed as the paired
-d[g]
<raw_device>
[MU#] logical volume (-d) or group (-dg). This option is effective without specification of “-g <group>“ option.
If the specified the raw_device is contained in two or more groups, the command is executed on the
first group.
Searches a group on the configuration definition file (local instance) for the specified LDEV, and if
the specified LDEV is in the group, the target volume is executed as the paired logical volume (-d) or
-d[g] <seq#>
<LDEV#> [MU#]
group (-dg). This option is effective without specification of “-g <group>“ option. If the specified LDEV
is contained in two or more groups, the command is executed on the first group. The <seq #> <LDEV
#> values can be specified in hexadecimal (by addition of “0x “) or decimal notation.
Suppresses messages to be displayed when this command is executed. It is used to execute this
command from a user program. This option must be specified at the beginning of a command
argument. The command execution log is not affected by this option.
-nomsg
Specifies the following data type that assumes the target volumes as Oracle database. If [type] is
not specified, then this option will disable all of the checking.
-vt [type]
• redo8: The target volumes sets the parameter for validation checking as Oracle redo log files
(including archive logs) prior Oracle9I. This option sets <bsize> to 1(512bytes) or 2(1024bytes).
• data8: The target volumes sets the parameter for validation checking as Oracle data files (including
control files) prior Oracle9I.
• redo9: The target volumes sets the parameter for validation checking as Oracle redo log files
(including archive logs) for Oracle9IR2 or later. This option sets <bsize> to 1 (512 bytes) or 2
(1024 bytes).
• data9: The target volumes sets the parameter for validation checking as Oracle data files (including
control files) for Oracle9IR2 later. For Oracle for Tru64 or Windows, set the parameter in the
init.ora file to “_HARD_PROTECTION = TRUE “. If not so, a parameter for validation must be
changed by using the following “-vmf we” option: raidvchkset -vt data9 -vmf we.
• rd10g: The target volumes sets the parameter for validation checking as Oracle ALL files ( including
redo and data and RMAN backup piece) for Oracle10gR2 or later. This option sets <bsize> to
1(512bytes) or 2(1024bytes). This option sets to the low 5 bits DBA for checking regarding
CHK-F2.
Specifies the data block size of Oracle I/O and a region on a target volume for validation checking.-vs <bsize>
[slba] [elba]
• <bsize> is used when specifying the data block size of Oracle I/O, in units of 512 bytes. <bsize>
is able to specify between 1 (512 bytes) and 64 (32 KB) (effective size for Oracle is also 1-64).
• [slba] [elba] is used when specifying a region defined between Start_LBA (0 based) and End_LBA
on a target volume for checking, in units of 512 bytes.
• [slba] [elba] can be specified in hexadecimal (by addition of “0x “) or decimal notation. If this
option is not specified, then a region for a target volume is set as all blocks (slba=0,elba=0).
Specifies the following guard type to the target volumes for Data Retention (Open LDEV Guard on
XP1024/XP128 Disk Array). If [type] is not specified, this option will disable all of the guarding.
-vg
[type]…[rtime]
The following values are available to specify on [type]:
• inv: The target volumes are concealed from SCSI Inquiry command by responding “unpopulated
volume”.
• sz0: The target volumes replies with “SIZE 0” through SCSI Read capacity command.
• rwd: The target volumes are disabled from reading and writing.
• wtd: The target volumes are disabled from writing.
• svd: If the target volume is SMPL, it is protected from paircreate (from becoming an S-VOL). If the
target volume is P-VOL, it is protected from pairresync restore or pairresync swaps(p). If the target
volume is S-VOL_PSUS(SSUS), it is protected from pairresync synchronous copy.
svd option can be used with the other option (inv, sz0, rwd, wtd) in parallel. For example, if you
want to protect the absolute volume from the writting executed by the copy series program product
and the host access, set the both wtd and svd options. The only setting of wtd option cannot
raidvchkset 71