HP P9000 RAID Manager Reference Guide (T1610-96037, October 2011)
DescriptionOption
# pairdisplay -g horc0 -fdxe Group ... LDEV#.P/S,Status,Fence,Seq#,P-LDEV# M CTG JID AP EM
E-Seq# E-LDEV# horc0 ... 41.P-VOL PAIR ASYNC ,63528 40 - 0 - 2 - - - horc0 ... 40.S-VOL PAIR
ASYNC ,----- 41 - 0 - - - - -
Display example for Business Copy/Snapshot:
# pairdisplay -g horc0 -fe Group ... Seq#,LDEV#.P/S,Status, Seq#,P-LDEV# M CTG CM EM E-Seq#
E-LDEV# horc0 ... 63528 65.P-VOL COPY,63528 64 - - N - - - horc0 ... 63528 64.S-VOL COPY,-----
65 - - N - - -
CTG: For Continuous Access Synchronous/Cnt Ac-J, the CT group ID when the Fence is shown as
ASYNC. For Continuous Access Synchronous Sync CTG, displays the CT group ID when the Fence
is shown as DATA/STATUS/NEVER. For Business Copy, the CT group ID on at-time split volumes
using Business Copy.
JID: The journal ID for P-VOL or S-VOL. ‘NOT Cnt Ac-J volume’ is shown as ‘-’.
AP: The number of active paths for HORC links on P-VOL, and it displays the number of active paths
for Cnt Ac-J links on P-VOL and S-VOL.’Unknown’is shown as ‘-’. Refer to “MINAP” information that
is displayed by running the pairvolchk command.
CM: The Copy mode:
• N: Non SnapShot
• S: SnapShot. In the SMPL state, this shows that pair-volume is created as SnapShot.
• C: Cruising Copy.
EM: The external connection mode:
• H: Mapped E-lun as hidden from the host.
• V: Mapped E-lun as visible to the host.
• ‘ - ‘: Unmapped to the E-lun.
• BH: Mapped E-lun as hidden from the host, but LDEV blockading.
• BV: Mapped E-lun as visible to the host, but LDEV blockading.
• B: Unmapped to the E-lun, but LDEV blockading.
E-Seq#: The production (serial) number of the external LUN, ‘Unknown’ is shown as ‘-’.
E-LDEV#: The LDEV# of the external LUN, ‘Unknown’ is shown as ‘-’.
Used when displaying the WWN setting (defined by “50060E80+RAID Type,Serial#,Port#)) to the
port instead of a port name. If this option is specified with the “-fe” option at the same line, then
-fw
“LUN WWN” appears as shown below. If WWN is not computed, then “Unknown” appears (For
example, SCSI).
Display example:
# pairdisplay -g PG01 -fw
Group PairVol(L/R) (WWN, LU-M),Seq#,LDEV#.P/S,Status, Seq#,P-LDEV# M
PG01 ora01(L) (500060e804f42001, 3-0) 62496 67. P-VOL COPY,62496 69 -
PG01 ora01(R) (500060e804f42001, 5-0 )62496 69. S-VOL COPY,----- 67 -
PG01 ora02(L) (500060e804f42001, 4-0 )62496 68. P-VOL COPY,62496 64 –
PG01 ora02(R) (500060e804f42001, 6-0 )62496 64.S-VOL COPY,----- 68 –
Display example:
# pairdisplay -IH -g PG01 -CLI -l -fwe
Group PairVol L/R WWN LU Seq# LDEV# P/S Status Fence Seq#
P-LDEV# M CTG JID AP EM E-Seq# E-LDEV# LUN-WWN
PG01 oradb01 L 500060e804fa0f01 1 64015 11 P-VOL PAIR ASYNC 62496
11 - 5 - 1 - - - 60060e8005fa0f000000fa0f0000000b
PG01 oradb02 L 500060e804fa0f01 2 64015 12 P-VOL PAIR ASYNC 62496
12 - 5 - 1 - - - 60060e8005fa0f000000fa0f0000000c
Used when specifying display for command line interface (CLI). This option displays to the same
position that defined number of columns, and displays one header. The delimiters between columns
are displayed as spaces or hyphens (-).
-CLI
52 Replication commands