HSG80 ACS Solution Software V8.6 for IBM AIM Installation and Configuration Guide
Table Of Contents
- HSG80 ACS Solution Software Version 8.6 for IBM AIX
- Contents
- Figures
- Tables
- About this Guide
- Chapter 1
- Planning a Subsystem
- Chapter 2
- Planning Storage
- Where to Start
- Configuration Rules
- Device PTL Addressing Convention
- Determining Storage Requirements
- Choosing a Container Type
- Creating a Storageset Profile
- Storageset Planning Considerations
- Storageset Expansion Considerations
- Partition Planning Considerations
- Changing Characteristics through Switches
- Storageset and Partition Switches
- Initialization Switches
- Unit Switches
- Storage Maps
- Chapter 3
- Preparing the Host System
- Chapter 4
- Installing and Configuring the HS-Series Agent
- Why Use StorageWorks Command Console (SWCC)?
- Installation and Configuration Overview
- About the Network Connection for the Agent
- Before Installing the Agent
- Installing and Configuring the Agent
- Running the Agent
- Reconfiguring the Agent
- Uninstall Agent, Storageworks Software, and Cambex Driver.
- High Availability Cluster Multi-Processor (HACMP)
- Enabler Software
- General Note on Software Installation
- SWCC Clients
- Running the Agent
- HACMP Implementation for the Agent
- Prerequisites
- Implementation
- Installing the Agent on an HACMP Cluster
- Installing and Configuring the Client on an HACMP cluster
- Operation of the Agent on an HACMP Cluster
- Normal Operation of the Agent on an HACMP Cluster
- Starting, Stopping and Checking for the Agent
- Password and Notification
- Client Functions and Storage Subsystem Options
- Failover with Agent as Part of a Resource Group
- Client IP Address
- Event Scripts
- Notification within HACMP
- Node Isolation Recovery
- Failure of the Agent
- Polling all nodes in cluster for presence of a running Agent
- Restarting the Agent on surviving node
- Notification
- Supporting Tools
- HACMP for AIX Primary Event Scripts
- HACMP for AIX Secondary Event Scripts
- Chapter 5
- Configuration Procedures
- Establishing a Local Connection
- Setting Up a Single Controller
- Setting Up a Controller Pair
- Configuring Devices
- Configuring a Stripeset
- Configuring a Mirrorset
- Configuring a RAIDset
- Configuring a Striped Mirrorset
- Configuring a Single-Disk Unit (JBOD)
- Configuring a Partition
- Assigning Unit Numbers and Unit Qualifiers
- Configuration Options
- Chapter 6
- Verifying Storage Configuration from the Host
- Chapter 7
- Configuration Example Using CLI
- Chapter 8
- Backing Up the Subsystem, Cloning Data for Backup, and Moving Storagesets
- Appendix A
- Subsystem Profile Templates
- Storageset Profile
- Storage Map Template 1 for the BA370 Enclosure
- Storage Map Template 2 for the second BA370 Enclosure
- Storage Map Template 3 for the third BA370 Enclosure
- Storage Map Template 4 for the Model 4214R Disk Enclosure
- Storage Map Template 5 for the Model 4254 Disk Enclosure
- Storage Map Template 6 for the Model 4310R Disk Enclosure
- Storage Map Template 7 for the Model 4350R Disk Enclosure
- Storage Map Template 8 for the Model 4314R Disk Enclosure
- Storage Map Template 9 for the Model 4354R Disk Enclosure
- Appendix B
- Installing, Configuring, and Removing the Client
- Appendix C
- Exploitation of the CLONE and SNAPSHOT Functions of the HSG80 in an AIX Environment
- Glossary
- Index
Preparing the Host System 3–11
e. Type y to stop the Agent.
f. At the main menu, type q to quit.
g. At the stgwks.sh menu, type q to exit and return to the command prompt.
3. Export any volume groups associated with disks on the HSG80 Raid Array by entering
the
exportvg command.
4. Delete all references to the adapters and hdisks associated with the Cambex driver by
performing the following actions:
a. Find all Cambex adapters on your system by entering the command
lsdev -Cc adapter
| grep Cambex
b. Enter the following command for each adapter: rmdev -Rdl scsiX
5. Uninstall your Q2100 driver by entering the following command:
installp -u Q2100.driver.obj
6. Enter the command: bosboot -ad /dev/ipldevice.
7. Install the new driver by entering the following command
installp -acd /<cdrom directory>/fcdriver/PC1000.image all
8. Enter the command: bosboot -ad /dev/ipldevice.
Now that the new driver is installed, go to the next part of the upgrade:
Upgrading the Storageworks Software and Agent.
Upgrading the Storageworks Software and Agent
IMPORTANT: Upgrade both the ODM entries and your agent. If you only upgrade one or the
other, it may be difficult to uninstall the agent or ODM entries.
To upgrade the the ODM entries and the SWCC agent perform the following procedure:
1. Go to the directory where you have your CD-ROM mounted
2. Enter the command
./INSTALL.
The first section of the script indicates that you already have a Cambex driver installed and
then asks if you want to continue. If you are not running V1.5.11.1 of the Cambex driver,
you need to upgrade your driver. Refer to the Examining and Upgrading Your Driver
section for instructions and then rerun this script