HSG80 ACS Solution Software V8.6 for IBM AIM Installation and Configuration Guide
Table Of Contents
- HSG80 ACS Solution Software Version 8.6 for IBM AIX
- Contents
- Figures
- Tables
- About this Guide
- Chapter 1
- Planning a Subsystem
- Chapter 2
- Planning Storage
- Where to Start
- Configuration Rules
- Device PTL Addressing Convention
- Determining Storage Requirements
- Choosing a Container Type
- Creating a Storageset Profile
- Storageset Planning Considerations
- Storageset Expansion Considerations
- Partition Planning Considerations
- Changing Characteristics through Switches
- Storageset and Partition Switches
- Initialization Switches
- Unit Switches
- Storage Maps
- Chapter 3
- Preparing the Host System
- Chapter 4
- Installing and Configuring the HS-Series Agent
- Why Use StorageWorks Command Console (SWCC)?
- Installation and Configuration Overview
- About the Network Connection for the Agent
- Before Installing the Agent
- Installing and Configuring the Agent
- Running the Agent
- Reconfiguring the Agent
- Uninstall Agent, Storageworks Software, and Cambex Driver.
- High Availability Cluster Multi-Processor (HACMP)
- Enabler Software
- General Note on Software Installation
- SWCC Clients
- Running the Agent
- HACMP Implementation for the Agent
- Prerequisites
- Implementation
- Installing the Agent on an HACMP Cluster
- Installing and Configuring the Client on an HACMP cluster
- Operation of the Agent on an HACMP Cluster
- Normal Operation of the Agent on an HACMP Cluster
- Starting, Stopping and Checking for the Agent
- Password and Notification
- Client Functions and Storage Subsystem Options
- Failover with Agent as Part of a Resource Group
- Client IP Address
- Event Scripts
- Notification within HACMP
- Node Isolation Recovery
- Failure of the Agent
- Polling all nodes in cluster for presence of a running Agent
- Restarting the Agent on surviving node
- Notification
- Supporting Tools
- HACMP for AIX Primary Event Scripts
- HACMP for AIX Secondary Event Scripts
- Chapter 5
- Configuration Procedures
- Establishing a Local Connection
- Setting Up a Single Controller
- Setting Up a Controller Pair
- Configuring Devices
- Configuring a Stripeset
- Configuring a Mirrorset
- Configuring a RAIDset
- Configuring a Striped Mirrorset
- Configuring a Single-Disk Unit (JBOD)
- Configuring a Partition
- Assigning Unit Numbers and Unit Qualifiers
- Configuration Options
- Chapter 6
- Verifying Storage Configuration from the Host
- Chapter 7
- Configuration Example Using CLI
- Chapter 8
- Backing Up the Subsystem, Cloning Data for Backup, and Moving Storagesets
- Appendix A
- Subsystem Profile Templates
- Storageset Profile
- Storage Map Template 1 for the BA370 Enclosure
- Storage Map Template 2 for the second BA370 Enclosure
- Storage Map Template 3 for the third BA370 Enclosure
- Storage Map Template 4 for the Model 4214R Disk Enclosure
- Storage Map Template 5 for the Model 4254 Disk Enclosure
- Storage Map Template 6 for the Model 4310R Disk Enclosure
- Storage Map Template 7 for the Model 4350R Disk Enclosure
- Storage Map Template 8 for the Model 4314R Disk Enclosure
- Storage Map Template 9 for the Model 4354R Disk Enclosure
- Appendix B
- Installing, Configuring, and Removing the Client
- Appendix C
- Exploitation of the CLONE and SNAPSHOT Functions of the HSG80 in an AIX Environment
- Glossary
- Index
Index-5
enabled for all disk units 1−8
removing
Client B−7
request rate 2−26
requirements
host adapter installation 3−5
restricting host access
disabling access paths
transparent failover 1−19
separate links
transparent failover 1−18
transparent failover 1−18
running
Agent 4−16
S
SAVE_CONFIGURATION 2−28
saving configuration 2−28
SCSI version
offset 1−16
SCSI-2
assigning unit numbers 1−16
command console lun 1−17
SCSI-3
assigning unit numbers 1−16
command console lun 1−16
Second enclosure of multiple-enclosure
subsystem
storage map template 2 A−4
selective storage presentation 1−17
SET CONNECTIONS
transparent failover 1−14
setting
controller configuration handling 2−28
single disk (JBOD)
assigning a unit number
fabric topology 5−21
Single-enclosure subsystem
storage map template 1
A−3
software
verification 3−13
storage
creating map 2−29
profile
example A−2
storage map 2−29
Storage map template 1 A−3
first enclosure of multiple-enclosure
subsystem A−3
, A−6, A−7, A−9, A−11,
A−12, A−14
single enclosure subsystem A−3
Storage map template 2 A−4
second enclosure of multiple-enclosure
subsystem A−4
Storage map template 3 A−5
third enclosure of multiple-enclosure
subsystem A−5
storageset
deleting
fabric topology 5−24
fabric topology
changing switches 5−25
planning considerations 2−14
mirrorsets 2−16
partitions 2−22
RAIDsets 2−18
striped mirrorsets 2−20
stripesets 2−14
profile 2−12
example 2−13
profiles A−1
storageset profile 2−12
storageset switches
SET command 2−24
storagesets
creating a profile 2−12
moving 8−6
striped mirrorsets
planning 2−21
planning considerations 2−20
stripesets
distributing members across buses 2−16
planning 2−15