HSG80 ACS Solution Software V8.6 for IBM AIM Installation and Configuration Guide
Table Of Contents
- HSG80 ACS Solution Software Version 8.6 for IBM AIX
- Contents
- Figures
- Tables
- About this Guide
- Chapter 1
- Planning a Subsystem
- Chapter 2
- Planning Storage
- Where to Start
- Configuration Rules
- Device PTL Addressing Convention
- Determining Storage Requirements
- Choosing a Container Type
- Creating a Storageset Profile
- Storageset Planning Considerations
- Storageset Expansion Considerations
- Partition Planning Considerations
- Changing Characteristics through Switches
- Storageset and Partition Switches
- Initialization Switches
- Unit Switches
- Storage Maps
- Chapter 3
- Preparing the Host System
- Chapter 4
- Installing and Configuring the HS-Series Agent
- Why Use StorageWorks Command Console (SWCC)?
- Installation and Configuration Overview
- About the Network Connection for the Agent
- Before Installing the Agent
- Installing and Configuring the Agent
- Running the Agent
- Reconfiguring the Agent
- Uninstall Agent, Storageworks Software, and Cambex Driver.
- High Availability Cluster Multi-Processor (HACMP)
- Enabler Software
- General Note on Software Installation
- SWCC Clients
- Running the Agent
- HACMP Implementation for the Agent
- Prerequisites
- Implementation
- Installing the Agent on an HACMP Cluster
- Installing and Configuring the Client on an HACMP cluster
- Operation of the Agent on an HACMP Cluster
- Normal Operation of the Agent on an HACMP Cluster
- Starting, Stopping and Checking for the Agent
- Password and Notification
- Client Functions and Storage Subsystem Options
- Failover with Agent as Part of a Resource Group
- Client IP Address
- Event Scripts
- Notification within HACMP
- Node Isolation Recovery
- Failure of the Agent
- Polling all nodes in cluster for presence of a running Agent
- Restarting the Agent on surviving node
- Notification
- Supporting Tools
- HACMP for AIX Primary Event Scripts
- HACMP for AIX Secondary Event Scripts
- Chapter 5
- Configuration Procedures
- Establishing a Local Connection
- Setting Up a Single Controller
- Setting Up a Controller Pair
- Configuring Devices
- Configuring a Stripeset
- Configuring a Mirrorset
- Configuring a RAIDset
- Configuring a Striped Mirrorset
- Configuring a Single-Disk Unit (JBOD)
- Configuring a Partition
- Assigning Unit Numbers and Unit Qualifiers
- Configuration Options
- Chapter 6
- Verifying Storage Configuration from the Host
- Chapter 7
- Configuration Example Using CLI
- Chapter 8
- Backing Up the Subsystem, Cloning Data for Backup, and Moving Storagesets
- Appendix A
- Subsystem Profile Templates
- Storageset Profile
- Storage Map Template 1 for the BA370 Enclosure
- Storage Map Template 2 for the second BA370 Enclosure
- Storage Map Template 3 for the third BA370 Enclosure
- Storage Map Template 4 for the Model 4214R Disk Enclosure
- Storage Map Template 5 for the Model 4254 Disk Enclosure
- Storage Map Template 6 for the Model 4310R Disk Enclosure
- Storage Map Template 7 for the Model 4350R Disk Enclosure
- Storage Map Template 8 for the Model 4314R Disk Enclosure
- Storage Map Template 9 for the Model 4354R Disk Enclosure
- Appendix B
- Installing, Configuring, and Removing the Client
- Appendix C
- Exploitation of the CLONE and SNAPSHOT Functions of the HSG80 in an AIX Environment
- Glossary
- Index
Index-3
dividing 2−22
removing from the spareset
fabric topology 5−23
displaying the current switches
fabric topology 5−25
dividing storagesets 2−22
E
enabling
switches 2−23
erasing metadata 2−28
establishing a local connection 5−2
F
Fabric topology
procedure flowchart
illustrated 4−ξξ
fabric topology
configuration
single controller cabling 5−3
failover 1−5
transparent 1−5
First enclosure of multiple-enclosure subsystem
storage map template 1 A−3
, A−6, A−7, A−9,
A−11, A−12, A−14
functions
Agent 4−1
G
geometry
initialize switches 2−28
H
host access
restricting by offsets
transparent failover 1−20
restricting in transparent failover mode 1−18
disabling access paths 1−19
separate links 1−18
host adapter
installation 3−5
preparation 3−5
host connections 1−11
naming 1−11
I
initialize switches
changing
fabric topology 5−26
CHUNKSIZE 2−26
geometry 2−28
NOSAVE_CONFIGURATION 2−28
SAVE_CONFIGURATION 2−28
installation
host adapter 3−5
invalid network port assignments B−3
there is no disk in the drive message B−4
installing
Agent 4−5
integrating SWCC B−8
invalid network port assignments B−3
J
JBOD 2−12
L
LOCATE
find devices 2−38
location
cache module 1−2
, 1−3
controller 1−2
, 1−3
LUN IDs
general description 1−23
LUN presentation 1−15
M
maintenance port connection
establishing a local connection 5−2
illustrated 5−2
mapping storagesets 2−29
messages
there is no disk in the drive B−4
mirrored caching
enabling 1−9
illustrated 1−9
mirrorset switches