HSG80 ACS Solution Software V8.6 for IBM AIM Installation and Configuration Guide
Table Of Contents
- HSG80 ACS Solution Software Version 8.6 for IBM AIX
- Contents
- Figures
- Tables
- About this Guide
- Chapter 1
- Planning a Subsystem
- Chapter 2
- Planning Storage
- Where to Start
- Configuration Rules
- Device PTL Addressing Convention
- Determining Storage Requirements
- Choosing a Container Type
- Creating a Storageset Profile
- Storageset Planning Considerations
- Storageset Expansion Considerations
- Partition Planning Considerations
- Changing Characteristics through Switches
- Storageset and Partition Switches
- Initialization Switches
- Unit Switches
- Storage Maps
- Chapter 3
- Preparing the Host System
- Chapter 4
- Installing and Configuring the HS-Series Agent
- Why Use StorageWorks Command Console (SWCC)?
- Installation and Configuration Overview
- About the Network Connection for the Agent
- Before Installing the Agent
- Installing and Configuring the Agent
- Running the Agent
- Reconfiguring the Agent
- Uninstall Agent, Storageworks Software, and Cambex Driver.
- High Availability Cluster Multi-Processor (HACMP)
- Enabler Software
- General Note on Software Installation
- SWCC Clients
- Running the Agent
- HACMP Implementation for the Agent
- Prerequisites
- Implementation
- Installing the Agent on an HACMP Cluster
- Installing and Configuring the Client on an HACMP cluster
- Operation of the Agent on an HACMP Cluster
- Normal Operation of the Agent on an HACMP Cluster
- Starting, Stopping and Checking for the Agent
- Password and Notification
- Client Functions and Storage Subsystem Options
- Failover with Agent as Part of a Resource Group
- Client IP Address
- Event Scripts
- Notification within HACMP
- Node Isolation Recovery
- Failure of the Agent
- Polling all nodes in cluster for presence of a running Agent
- Restarting the Agent on surviving node
- Notification
- Supporting Tools
- HACMP for AIX Primary Event Scripts
- HACMP for AIX Secondary Event Scripts
- Chapter 5
- Configuration Procedures
- Establishing a Local Connection
- Setting Up a Single Controller
- Setting Up a Controller Pair
- Configuring Devices
- Configuring a Stripeset
- Configuring a Mirrorset
- Configuring a RAIDset
- Configuring a Striped Mirrorset
- Configuring a Single-Disk Unit (JBOD)
- Configuring a Partition
- Assigning Unit Numbers and Unit Qualifiers
- Configuration Options
- Chapter 6
- Verifying Storage Configuration from the Host
- Chapter 7
- Configuration Example Using CLI
- Chapter 8
- Backing Up the Subsystem, Cloning Data for Backup, and Moving Storagesets
- Appendix A
- Subsystem Profile Templates
- Storageset Profile
- Storage Map Template 1 for the BA370 Enclosure
- Storage Map Template 2 for the second BA370 Enclosure
- Storage Map Template 3 for the third BA370 Enclosure
- Storage Map Template 4 for the Model 4214R Disk Enclosure
- Storage Map Template 5 for the Model 4254 Disk Enclosure
- Storage Map Template 6 for the Model 4310R Disk Enclosure
- Storage Map Template 7 for the Model 4350R Disk Enclosure
- Storage Map Template 8 for the Model 4314R Disk Enclosure
- Storage Map Template 9 for the Model 4354R Disk Enclosure
- Appendix B
- Installing, Configuring, and Removing the Client
- Appendix C
- Exploitation of the CLONE and SNAPSHOT Functions of the HSG80 in an AIX Environment
- Glossary
- Index
Index-2 HSG80 ACS Solution Software Version 8.6 for IBM AIX Installation and Configuration Guide
CHUNKSIZE 2−26
CLI prompt
changing
fabric topology 5−22
Client
removing B−7
uninstalling B−7
CLONE utility
backup 8−2
cloning
backup 8−2
command console LUN 1−9
SCSI-2 mode 1−17
SCSI-3 mode 1−16
Compaq Insight Manager B−8
comparison of container types 2−12
Configuration
fabric topology
procedure flowchart
illustrated 4−ξξ
configuration
backup 8−1
fabric topology
devices 5−16
multiple-bus failover
cabling 5−10
multiple-bus failover using CLI 7−4
single controller cabling 5−3
restoring 2−28
rules 2−3
configuration options
fabric topology
adding a disk drive to the spareset 5−23
adding disk drives 5−23
changing switches
device 5−25
displaying the current switches 5−25
initialize 5−26
RAIDset and mirrorset 5−25
unit 5−26
changing switches for a storageset or
device 5−25
changing the CLI prompt 5−22
deleting a storageset 5−24
enabling autospare 5−24
removing a disk drive from the spareset
5−23
configuring
pager notification B−8
configuring devices
fabric topology 5−16
connections 1−11
naming 1−11
containers
attributes 2−11
comparison 2−12
illustrated 2−11
mirrorsets 2−16
planning storage 2−11
stripesets 2−15
controllers
cabling 5−4
, 5−11
location 1−2
, 1−3
node IDs 1−21
worldwide names 1−21
creating
storageset and device profiles 2−12
D
device switches
changing
fabric topology 5−25
devices
changing switches
fabric topology 5−25
configuration
fabric topology 5−16
creating a profile 2−12
disk drives
adding
fabric topology 5−23
adding to the spareset
fabric topology 5−23
array 2−12
corresponding storagesets 2−29