HSG80 ACS Solution Software V8.6 for IBM AIM Installation and Configuration Guide
Table Of Contents
- HSG80 ACS Solution Software Version 8.6 for IBM AIX
- Contents
- Figures
- Tables
- About this Guide
- Chapter 1
- Planning a Subsystem
- Chapter 2
- Planning Storage
- Where to Start
- Configuration Rules
- Device PTL Addressing Convention
- Determining Storage Requirements
- Choosing a Container Type
- Creating a Storageset Profile
- Storageset Planning Considerations
- Storageset Expansion Considerations
- Partition Planning Considerations
- Changing Characteristics through Switches
- Storageset and Partition Switches
- Initialization Switches
- Unit Switches
- Storage Maps
- Chapter 3
- Preparing the Host System
- Chapter 4
- Installing and Configuring the HS-Series Agent
- Why Use StorageWorks Command Console (SWCC)?
- Installation and Configuration Overview
- About the Network Connection for the Agent
- Before Installing the Agent
- Installing and Configuring the Agent
- Running the Agent
- Reconfiguring the Agent
- Uninstall Agent, Storageworks Software, and Cambex Driver.
- High Availability Cluster Multi-Processor (HACMP)
- Enabler Software
- General Note on Software Installation
- SWCC Clients
- Running the Agent
- HACMP Implementation for the Agent
- Prerequisites
- Implementation
- Installing the Agent on an HACMP Cluster
- Installing and Configuring the Client on an HACMP cluster
- Operation of the Agent on an HACMP Cluster
- Normal Operation of the Agent on an HACMP Cluster
- Starting, Stopping and Checking for the Agent
- Password and Notification
- Client Functions and Storage Subsystem Options
- Failover with Agent as Part of a Resource Group
- Client IP Address
- Event Scripts
- Notification within HACMP
- Node Isolation Recovery
- Failure of the Agent
- Polling all nodes in cluster for presence of a running Agent
- Restarting the Agent on surviving node
- Notification
- Supporting Tools
- HACMP for AIX Primary Event Scripts
- HACMP for AIX Secondary Event Scripts
- Chapter 5
- Configuration Procedures
- Establishing a Local Connection
- Setting Up a Single Controller
- Setting Up a Controller Pair
- Configuring Devices
- Configuring a Stripeset
- Configuring a Mirrorset
- Configuring a RAIDset
- Configuring a Striped Mirrorset
- Configuring a Single-Disk Unit (JBOD)
- Configuring a Partition
- Assigning Unit Numbers and Unit Qualifiers
- Configuration Options
- Chapter 6
- Verifying Storage Configuration from the Host
- Chapter 7
- Configuration Example Using CLI
- Chapter 8
- Backing Up the Subsystem, Cloning Data for Backup, and Moving Storagesets
- Appendix A
- Subsystem Profile Templates
- Storageset Profile
- Storage Map Template 1 for the BA370 Enclosure
- Storage Map Template 2 for the second BA370 Enclosure
- Storage Map Template 3 for the third BA370 Enclosure
- Storage Map Template 4 for the Model 4214R Disk Enclosure
- Storage Map Template 5 for the Model 4254 Disk Enclosure
- Storage Map Template 6 for the Model 4310R Disk Enclosure
- Storage Map Template 7 for the Model 4350R Disk Enclosure
- Storage Map Template 8 for the Model 4314R Disk Enclosure
- Storage Map Template 9 for the Model 4354R Disk Enclosure
- Appendix B
- Installing, Configuring, and Removing the Client
- Appendix C
- Exploitation of the CLONE and SNAPSHOT Functions of the HSG80 in an AIX Environment
- Glossary
- Index
Glossary–17
serial transmission A method transmission in which each bit of information is sent sequentially
on a single channel rather than simultaneously as in parallel transmission.
signal converter See SCSI bus signal converter.
single ended I/O
module
A 16-bit I/O module. See also I/O module.
single-ended
SCSI bus
An electrical connection where one wire carries the signal and another wire or
shield is connected to electrical ground. Each signal logic level is determined
by the voltage of a single wire in relation to ground. This is in contrast to a
differential connection where the second wire carries an inverted signal.
spareset A collection of disk drives made ready by the controller to replace failed
members of a storageset.
storage array An integrated set of storage devices.
storage array
subsystem
See storage subsystem.
storageset (1) A group of devices configured with RAID techniques to operate as a single
container. (2) Any collection of containers, such as stripesets, mirrorsets,
striped mirrorsets, and RAIDsets.
storageset
expansion
Concat commands implement storageset expansion features.
storage subsystem The controllers, storage devices, shelves, cables, and power supplies used to
form a mass storage subsystem.
storage unit The general term that refers to storagesets, single-disk units, and all other
storage devices that are installed in your subsystem and accessed by the host.
A storage unit can be any entity that is capable of storing data, whether it is a
physical device or a group of physical devices.
StorageWorks A family of Compaq modular data storage products that allow customers to
design and configure their own storage subsystems. Components include
power, packaging, cabling, devices, controllers, and software. Customers can
integrate devices and array controllers in StorageWorks enclosures to form
storage subsystems.
StorageWorks systems include integrated SBBs and array controllers to form
storage subsystems. System-level enclosures to house the shelves and standard
mounting devices for SBBs are also included.