HSG80 ACS Solution Software V8.6 for IBM AIM Installation and Configuration Guide

ManualsBrandsHP ManualsStorageHP StorageWorks MA6000 D14 High Performance Model

161

162

163

164

165

166

167

168

169

170

Table Of Contents

HSG80 ACS Solution Software Version 8.6 for IBM AIX
Contents
Figures
Tables
About this Guide
- Text Conventions
- Symbols in Text
- Symbols on Equipment
- Rack Stability
- Installation and Setup of the CD-ROM
- Configuration Flowchart
- Getting Help
- Compaq Technical Support
- Compaq Website
- Compaq Authorized Reseller
Chapter 1
Planning a Subsystem
- Defining the Subsystems
  - Controller Designations A and B
  - Controller Designations “This Controller” and “Other Controller”
- Failover Mode
  - Transparent Failover Mode
- Selecting a Cache Mode
- Enabling Mirrored Caching
- The Command Console LUN
- Connections
  - Naming Connections
  - Numbers of Connections
- Assigning Unit Numbers
  - Matching Units to Host Connections in Transparent Failover Mode
  - Assigning Unit Numbers Depending on SCSI_VERSION
    - Assigning Host Connection Offsets and Unit Numbers in SCSI-3 Mode
    - Assigning Host Connection Offsets and Unit Numbers in SCSI-2 Mode
- Selective Storage Presentation
  - Restricting Host Access in Transparent Failover Mode
- Worldwide Names (NodeIDs and Port IDs)
  - Restoring Worldwide Names (Node IDs)
  - Unit Worldwide Names (LUN IDs)
Chapter 2
Planning Storage
- Where to Start
- Configuration Rules
- Device PTL Addressing Convention
- Determining Storage Requirements
- Choosing a Container Type
- Creating a Storageset Profile
- Storageset Planning Considerations
- Storageset Expansion Considerations
- Partition Planning Considerations
  - Defining a Partition
  - Guidelines for Partitioning Storagesets and Disk Drives
- Changing Characteristics through Switches
  - Enabling Switches
  - Changing Switches
- Storageset and Partition Switches
- Initialization Switches
- Unit Switches
- Storage Maps
  - Creating a Storage Map
  - Using the LOCATE Command to Find Devices
Chapter 3
Preparing the Host System
- Enterprise Storage RAID Array Storage System Installation
- Making a Physical Connection
  - Preparing to Install the Host Bus Adapter
  - Installing the Host Bus Adapter
- Storage Works Platform Kit Installation
  - Fresh Install
  - Upgrade Install
    - Examining and Upgrading Your Driver
    - Upgrading the Storageworks Software and Agent
Chapter 4
Installing and Configuring the HS-Series Agent
- Why Use StorageWorks Command Console (SWCC)?
- Installation and Configuration Overview
- About the Network Connection for the Agent
- Before Installing the Agent
- Installing and Configuring the Agent
  - Installing the Agent for the First Time
  - Upgrading the Agent
- Running the Agent
- Reconfiguring the Agent
- Uninstall Agent, Storageworks Software, and Cambex Driver.
  - Agent Only Uninstall
  - Everything Uninstall
- High Availability Cluster Multi-Processor (HACMP)
Chapter 5
Configuration Procedures
- Establishing a Local Connection
- Setting Up a Single Controller
- Setting Up a Controller Pair
- Configuring Devices
- Configuring a Stripeset
- Configuring a Mirrorset
- Configuring a RAIDset
- Configuring a Striped Mirrorset
- Configuring a Single-Disk Unit (JBOD)
- Configuring a Partition
- Assigning Unit Numbers and Unit Qualifiers
- Configuration Options
Chapter 6
Verifying Storage Configuration from the Host
Chapter 7
Configuration Example Using CLI
- CLI Configuration Example
Chapter 8
Backing Up the Subsystem, Cloning Data for Backup, and Moving Storagesets
- Backing Up the Subsystem Configuration
- Cloning Data for Backup
- Moving Storagesets
Appendix A
Subsystem Profile Templates
- Storageset Profile
- Storage Map Template 1 for the BA370 Enclosure
- Storage Map Template 2 for the second BA370 Enclosure
- Storage Map Template 3 for the third BA370 Enclosure
- Storage Map Template 4 for the Model 4214R Disk Enclosure
- Storage Map Template 5 for the Model 4254 Disk Enclosure
- Storage Map Template 6 for the Model 4310R Disk Enclosure
- Storage Map Template 7 for the Model 4350R Disk Enclosure
- Storage Map Template 8 for the Model 4314R Disk Enclosure
- Storage Map Template 9 for the Model 4354R Disk Enclosure
Appendix B
Installing, Configuring, and Removing the Client
- Why Install the Client?
- Before You Install the Client
- Installing the Client
- Troubleshooting the Client Installation
  - Invalid Network Port Assignments During Installation
  - “There is no disk in the drive” Message
- Adding the Storage Subsystem and its Host to the Navigation Tree
- Removing the Command Console Client
- Where to Find Additional Information
  - About the User Guide
  - About the Online Help
Appendix C
Exploitation of the CLONE and SNAPSHOT Functions of the HSG80 in an AIX Environment
Glossary
Index

8–2 HSG80 ACS Solution Software Version 8.6 for IBM AIX Installation and Configuration Guide

Cloning Data for Backup

Use the CLONE utility to duplicate the data on any unpartitioned single-disk unit,

stripeset, mirrorset, or striped mirrorset in preparation for backup. When the cloning

operation is complete, you can back up the clones rather than the storageset or single-disk

unit, which can continue to service its I/O load. When you are cloning a mirrorset,

CLONE does not need to create a temporary mirrorset. Instead, it adds a temporary

member to the mirrorset and copies the data onto this new member.

The CLONE utility creates a temporary, two-member mirrorset for each member in a

single-disk unit or stripeset. Each temporary mirrorset contains one disk drive from the

unit you are cloning and one disk drive onto which CLONE copies the data. During the

copy operation, the unit remains online and active so that the clones contain the most

up-to-date data.

After the CLONE utility copies the data from the members to the clones, it restores the

unit to its original configuration and creates a clone unit you can back up. The CLONE

utility uses steps shown in Figure 8–1 to duplicate each member of a unit.