HSG80 ACS Solution Software V8.6 for IBM AIM Installation and Configuration Guide
Table Of Contents
- HSG80 ACS Solution Software Version 8.6 for IBM AIX
- Contents
- Figures
- Tables
- About this Guide
- Chapter 1
- Planning a Subsystem
- Chapter 2
- Planning Storage
- Where to Start
- Configuration Rules
- Device PTL Addressing Convention
- Determining Storage Requirements
- Choosing a Container Type
- Creating a Storageset Profile
- Storageset Planning Considerations
- Storageset Expansion Considerations
- Partition Planning Considerations
- Changing Characteristics through Switches
- Storageset and Partition Switches
- Initialization Switches
- Unit Switches
- Storage Maps
- Chapter 3
- Preparing the Host System
- Chapter 4
- Installing and Configuring the HS-Series Agent
- Why Use StorageWorks Command Console (SWCC)?
- Installation and Configuration Overview
- About the Network Connection for the Agent
- Before Installing the Agent
- Installing and Configuring the Agent
- Running the Agent
- Reconfiguring the Agent
- Uninstall Agent, Storageworks Software, and Cambex Driver.
- High Availability Cluster Multi-Processor (HACMP)
- Enabler Software
- General Note on Software Installation
- SWCC Clients
- Running the Agent
- HACMP Implementation for the Agent
- Prerequisites
- Implementation
- Installing the Agent on an HACMP Cluster
- Installing and Configuring the Client on an HACMP cluster
- Operation of the Agent on an HACMP Cluster
- Normal Operation of the Agent on an HACMP Cluster
- Starting, Stopping and Checking for the Agent
- Password and Notification
- Client Functions and Storage Subsystem Options
- Failover with Agent as Part of a Resource Group
- Client IP Address
- Event Scripts
- Notification within HACMP
- Node Isolation Recovery
- Failure of the Agent
- Polling all nodes in cluster for presence of a running Agent
- Restarting the Agent on surviving node
- Notification
- Supporting Tools
- HACMP for AIX Primary Event Scripts
- HACMP for AIX Secondary Event Scripts
- Chapter 5
- Configuration Procedures
- Establishing a Local Connection
- Setting Up a Single Controller
- Setting Up a Controller Pair
- Configuring Devices
- Configuring a Stripeset
- Configuring a Mirrorset
- Configuring a RAIDset
- Configuring a Striped Mirrorset
- Configuring a Single-Disk Unit (JBOD)
- Configuring a Partition
- Assigning Unit Numbers and Unit Qualifiers
- Configuration Options
- Chapter 6
- Verifying Storage Configuration from the Host
- Chapter 7
- Configuration Example Using CLI
- Chapter 8
- Backing Up the Subsystem, Cloning Data for Backup, and Moving Storagesets
- Appendix A
- Subsystem Profile Templates
- Storageset Profile
- Storage Map Template 1 for the BA370 Enclosure
- Storage Map Template 2 for the second BA370 Enclosure
- Storage Map Template 3 for the third BA370 Enclosure
- Storage Map Template 4 for the Model 4214R Disk Enclosure
- Storage Map Template 5 for the Model 4254 Disk Enclosure
- Storage Map Template 6 for the Model 4310R Disk Enclosure
- Storage Map Template 7 for the Model 4350R Disk Enclosure
- Storage Map Template 8 for the Model 4314R Disk Enclosure
- Storage Map Template 9 for the Model 4354R Disk Enclosure
- Appendix B
- Installing, Configuring, and Removing the Client
- Appendix C
- Exploitation of the CLONE and SNAPSHOT Functions of the HSG80 in an AIX Environment
- Glossary
- Index
5–6 HSG80 ACS Solution Software Version 8.6 for IBM AIX Installation and Configuration Guide
6. To set the prompt to the HSG80 controller, enter:
SET THIS_CONTROLLER PROMPT=”HSG>”
7. Clear the persistent error messages by entering the following command:
HSG> CLEAR CLI
8. Set the node by acquiring the Worldwide Name (WWN) node number and checksum
from the enclosed label (located on the top surface of the controller enclosure), and by
entering the following command:
HSG> SET THIS_CONTROLLER NODE=NNNN-NNNN-NNNN-NNNN CHECKSUM
9. Enable the command console LUN by entering the following command:
HSG> SET THIS_CONTROLLER COMMAND_CONSOLE_LUN
10. Set the port topology offline by entering the following command:
HSG> SET THIS_CONTROLLER PORT_1_TOPOLOGY=OFFLINE
HSG> SET THIS_CONTROLLER PORT_2_TOPOLOGY=OFFLINE
11. Set the port topology by entering the following command:
HSG> SET THIS_CONTROLLER PORT_1_TOPOLOGY=FABRIC
HSG> SET THIS_CONTROLLER PORT_2_TOPOLOGY=FABRIC
See Table 5–1 on page 5 for an example of LOOP_HARD topology setup.
12. Set the SCSI version by entering the following command:
HSG> SET THIS_CONTROLLER SCSI VERSION=SCSI-2
13. Determine if the operating system set for the online controller connection is WINNT,
by entering the following command:
HSG> SHOW CONNECTIONS
Although an IBM operating system entry exists in the CLI and SWCC for the fibre
channel connection, use default setting WINNT for operation with your IBM host. The
IBM setting may cause problems when LUNs are not available to AIX or during
controller failover. If so, use:
HSG> SET !NEWCONxx OPERATING_SYSTEM=WINNT
where: xx is the online connection ID produced in the SHOW CONNECTIONS command
above.
NOTE: Further information on command syntax can be found in the Compaq StorageWorks
HSG80 Array Controller ACS Version 8.6 CLI Reference Guide.