HP StorageWorks ESL E-Series Tape Library Internal Network Kit Installation and Replacement Instructions (AH997-96001, September 2007)

11Removethescrewsfromthedrive
clusters
If you are replacing the switch, skip this step because the screws will
already be removed.
11590
Keep the screws to use for at taching the switch to the cabinet.
12 Insert t
he switch into the cabinet and
attach it with the screws
11587
Route the power cable so it will reach the PDU. Use a #2 Phillips
screwdriver to tighten the screws.
13 Plug the c ables into the switch
11609
NOTE:
If an LTO4 tape drive is not installed, follow the instructions on
the tape drive installation poster to install it .
If the switch was previously installed, use the labels on the cables or
the note that you wrote to reconnect the cables exactly as they were
connected before. If you are installing the switch for the first time, plug
an Ether
net cable from the MGMT port on each LTO4 tape drive to a
number
ed port on the switch. HP recommends that you connect the
tape dr
ives to the switch in order starting with cluster 1, tape drive A
connecting to port 1. If you have 24 tape drives, connect tape drive
24 to p
ort E4 on the cluster controller (left card in the drive cluster) in
the bo
ttom drive cluster (port 24 is used i n the next step). LTO3 tape
driv
es do not plug into this switch.
14 Connect the switch to a cluster
controller
ACT/
LNK
ACT/
LNK
PORT 1 PORT 0 ETHERNET
SERIAL
PWR
FIBRE
CHANNEL
FIBRE
CHANNEL
ACT/
LNK
PORT 2
FIBRE
CHANNEL
ACT/
LNK
ACT/
LNK
PORT 1 PORT 3
FIBRE
CHANNEL
FIBRE
CHANNEL
ACT/
LNK
PORT 2
FIBRE
CHANNEL
ACT/
LNK
ACT/
LNK
PORT 1 PORT 0 ETHERNET
SERIAL
PWR
FIBRE
CHANNEL
FIBRE
CHANNEL
ACT/
LNK
PORT 2
FIBRE
CHANNEL
ACT/
LNK
ACT/
LNK
PORT 1 PORT 3
FIBRE
CHANNEL
FIBRE
CHANNEL
ACT/
LNK
PORT 2
FIBRE
CHANNEL
ACT/
LNK
ACT/
LNK
PORT 1 PORT 0 ETHERNET
SERIAL
PWR
FIBRE
CHANNEL
FIBRE
CHANNEL
ACT/
LNK
PORT 2
FIBRE
CHANNEL
ACT/
LNK
ACT/
LNK
PORT 1 PORT 3
FIBRE
CHANNEL
FIBRE
CHANNEL
ACT/
LNK
PORT 2
FIBRE
CHANNEL
ACT/
LNK
ACT/
LNK
PORT 1 PORT 0 ETHERNET
SERIAL
PWR
FIBRE
CHANNEL
FIBRE
CHANNEL
ACT/
LNK
PORT 2
FIBRE
CHANNEL
ACT/
LNK
ACT/
LNK
PORT 1 PORT 3
FIBRE
CHANNEL
FIBRE
CHANNEL
ACT/
LNK
PORT 2
FIBRE
CHANNEL
ACT/
LNK
ACT/
LNK
PORT 1 PORT 0 ETHERNET
SERIAL
PWR
FIBRE
CHANNEL
FIBRE
CHANNEL
ACT/
LNK
PORT 2
FIBRE
CHANNEL
ACT/
LNK
ACT/
LNK
PORT 1 PORT 3
FIBRE
CHANNEL
FIBRE
CHANNEL
ACT/
LNK
PORT 2
FIBRE
CHANNEL
ACT/
LNK
ACT/
LNK
PORT 1 PORT 0 ETHERNET
SERIAL
PWR
FIBRE
CHANNEL
FIBRE
CHANNEL
ACT/
LNK
PORT 2
FIBRE
CHANNEL
ACT/
LNK
ACT/
LNK
PORT 1 PORT 3
FIBRE
CHANNEL
FIBRE
CHANNEL
ACT/
LNK
PORT 2
FIBRE
CHANNEL
ACT/
LNK
ACT/
LNK
PORT 1 PORT 0 ETHERNET
SERIAL
PWR
FIBRE
CHANNEL
FIBRE
CHANNEL
ACT/
LNK
PORT 2
FIBRE
CHANNEL
ACT/
LNK
ACT/
LNK
PORT 1 PORT 3
FIBRE
CHANNEL
FIBRE
CHANNEL
ACT/
LNK
PORT 2
FIBRE
CHANNEL
11649
ConnectanEthernetcablefromport24ontheswitchtoanyunusedE#
port on any of the cluster controllers (left card in the drive cluster).
Page 4