FW 08.01.00/HAFM SW 08.06.xx or later HP StorageWorks Edge Switch 2/24 Installation Guide (AA-RTDWE-TE, November 2005)
Table Of Contents
- Edge Switch 2/24 installation guide
- Contents
- Introduction to the Edge Switch 2/24
- Installing the Edge Switch
- Connecting the Edge Switch
- Edge Switch network addresses
- LAN-connecting the Edge Switch
- Setting up the HAFM appliance
- Using HAFM to configure the Edge Switch
- Setting the Edge Switch online and offline
- Configuring Edge Switch identification
- Configuring Edge Switch operating parameters
- Configuring fabric operating parameters
- Configuring switch binding
- Configuring preferred path
- Configuring ports
- Configuring SNMP trap message recipients
- Configuring, enabling, and testing e-mail notification
- Configuring and enabling call-home features
- Configuring and enabling Ethernet events
- Configuring, enabling, and testing call-home event notification
- Threshold alerts
- Creating new alerts
- Figure 30 Configure Threshold Alerts dialog box
- Figure 31 New Threshold Alerts dialog box-first screen
- Figure 32 New Threshold Alerts dialog box-second screen
- Figure 33 New Threshold Alerts dialog box-third screen
- Figure 34 New Threshold Alerts dialog box-summary screen
- Figure 35 Configure Threshold Alerts dialog box-alert activated
- Modifying alerts
- Activating or deactivating alerts
- Deleting alerts
- Creating new alerts
- Configuring SANtegrity Authentication
- Backing up HAFM configuration data
- Resetting configuration data
- Enabling the HAFM Basic interface
- Enabling Telnet
- Connecting the Edge Switch to a fabric
- Using the HAFM Basic interface
- Launching the HAFM Basic interface
- Setting the Edge Switch offline and online
- Configuring Edge Switch ports
- Configuring BB credit
- Configuring Edge Switch identification
- Configuring date and time
- Configuring Edge Switch parameters
- Configuring network information
- Configuring SNMP trap message recipients
- Enabling or disabling the CLI
- Configuring zoning
- Managing firmware versions
- Regulatory compliance and safety
- Technical specifications
- Index
Edge Switch 2/24 installation guide 39
The Configure Date and Time dialog box is displayed (Figure 17).
Figure 17 Configure Date and Time dialog box
2. To set the date and time manually, see ”Setting the date and time manually” on page 39. Or, to
periodically synchronize the date and time, see .
Setting the date and time manually
To set the Edge Switch date and time manually:
1. At the Configure Date and Time dialog box, clear the Periodic Date/Time Synchronization check
box.
The greyed out Date and Time fields are activated.
2. Click the Date boxes that require change, and enter numbers in the following ranges:
Month (MM): 1 through 12
Day (DD): 1 through 31
Year (YYYY): greater than 1980
3. Click the Time boxes that require change, and enter numbers in the following ranges:
Hour (HH): 0 through 23
Minute (MM): 0 through 59
Second (SS): 0 through 59
4. Click Activate to set the Edge Switch date and time and close the Configure Date and Time
dialog box.
Periodically synchronizing the date and time
To periodically synchronize the Edge Switch date and time with the HAFM appliance:
1. Select the Periodic Date/Time Synchronization check box.
The Date and Time fields are greyed out.
2. Perform one of the following actions:
•Click Activate to enable synchronization and close the Configure Date and Time dialog box.
The Edge Switch date and time synchronize with the HAFM appliance date and time at the
next update period (at least once daily).
•Click Sync Now to synchronize the Edge Switch and HAFM appliance immediately.
The Date and Time Synced dialog box is displayed.
3. Click OK to synchronize the date and time and close the Date and Time Synced dialog box, and
then click Activate to enable synchronization and close the Configure Date and Time dialog box.