HP StorageWorks All-in-One SB600c Storage Blade installation instructions (AG780-96002, September 2008)

ManualsBrandsHP ManualsStorageHP StorageWorks AiO SB600c Storage Blade

HP StorageWorks

All-in-One SB60

0c Storage

Blade installation instructions

L.P.

First edition: September 2008

The info

rmationinthisdocumentissubjecttochangewithout

notice.

Printed in Puerto Rico

www.hp.com

G780-96002*

Over view

Installation of a storage and server blade requires the following steps:

1. Install and conﬁgure an HP BladeSystem c-Class enclosure.

2. Install any blade options.

3. Install interconnect modules in the enclosure.

4. Connect the interconnect modules to the network.

5. Install a storage and server blade.

6. Complete the storage and server blade conﬁguration.

Installing an HP BladeSystem c-Class

enclosure

Before perf

orming any b lade-speciﬁc procedures, install an HP

BladeSyste

mc-Classenclosure.

The most cur

rent documentation for blades and other HP

BladeSyste

m components is available at the HP website

(http://w

ww.hp.com/go/bladesystem/documentation).

Documentation is also available in the following locations:

• Documentation CD that ships with the enclosure

• HP Business Support Center website (http ://www.hp.com/support)

• HP Technical Documentation website (http://docs.hp.com)

Installing blade options

Before installing and initializing the storage and server blade, install

any blad e options, such as an additional mezzanine card. For blade

options installation information, see the HP ProLiant BL460c Server

Blade User Guide on the Documentation CD or on the H P website

(http://www.hp.com/go/bladesystem/documentation).

Installing interconnect modules

For speciﬁc steps to install interconnect modules, see the documentation

that sh ips with the interconnect mod u le.

To suppor t network connections for speciﬁc s ignals, install an

interconnect module in the bay corresponding to the embedded NIC or

mezzanine signals.

Page 1

Summary of content (4 pages)

PAGE 1
HP StorageWorks All-in-One SB600c Storage Blade installation instructions Overview Installation of a storage and server blade requires the following steps: 1. Install and configure an HP BladeSystem c-Class enclosure. 2. Install any blade options. 3. Install interconnect modules in the enclosure. 4. Connect the interconnect modules to the network. 5. Install a storage and server blade. 6. Complete the storage and server blade configuration.
PAGE 2
Figure 1 Interconnect bay numbering and device mapping (c7000 enclosure) Blade signal Interconnect bay NIC 1 (embedded) 1 NIC 2 (embedded) 2 Mezzanine 1 3 and 4 Mezzanine 2 5 and 6 Figure 2 Interconnect bay numbering and device mapping (c3000 enclosure) Interconnect bay label 7 and 8 Blade signal Interconnect bay NICs 1 and 2 (embedded) 1 Mezzanine 1 2 Four port cards connect to bay 2 3, 4 • Four port cards • Ports 1 and 3 connect to bay 3 • Ports 2 and 4 connect to bay 4 3, 4 • Four
PAGE 3
Installing a storage and server blade IMPORTANT: If your HP AiO SB600c Storage Blade is factory-integrated, the server and storage blades are pre-installed in the enclosure. CAUTION: To prevent improper cooling and thermal damage, do not operate the blade or the enclosure unless all hard drive and device bays are populated with either a component or a blank. 2. Prepare the storage blade for installation. The AiO SB600c consists of a server blade and storage blade.
PAGE 4
NOTE: The HP AiO SB600c Storage Blade comes pre-installed with the Microsoft Windows Storage Server 2003 R2 (Standard Edition) operating system. There is no operating system installation required. After the enclosure has been configured and the storage system installation process is complete, log on to the storage system using the default user name administrator and password hpinvent.