Linux Trap ID and SNMP Traps Reference Guide For use with SmartStart version 8.30

ManualsBrandsHP ManualsSoftwareHP SmartStart Maintenance Single Release Software

Linux Trap ID and SNMP Traps

Reference Guide

For use with SmartStart version 8.30

Seventh Edition July 2009

436717-007

Summary of content (53 pages)

PAGE 1
Linux Trap ID and SNMP Traps Reference Guide For use with SmartStart version 8.
PAGE 2
Legal notices © Copyright 2006−2009 Hewlett-Packard Development Company, L.P. Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor’s standard commercial license. The information contained herein is subject to change without notice.
PAGE 3
Contents Contents.........................................................................................................................................................................3 Introduction ...................................................................................................................................................................4 Where to go for additional help ..................................................................................................................
PAGE 4
Introduction This guide contains a listing of the Linux Trap ID messages associated with SNMP traps that are generated by the HP Insight Management Agents for Servers for Linux. Each event entry has the corresponding SNMP trap number used by the agents. Where to go for additional help In addition to this guide, the following information sources are available:  User documentation  HP Insight Manager software Telephone numbers If you have purchased a Care Pack (service upgrade), call 1-800-633-3600.
PAGE 5
Foundation agents Trap IDs: 10003-10008 10003 - cmathreshd Log message: “Compaq Generic Test Trap (10003): %s” SNMP trap: cpqHo2GenericTrap - 1003 in PQHOST.MIB Symptom: Generic trap. Supporting SNMP trap data:  sysName  cpqHoTrapFlags  cpqHoGenericData Supporting SNMP trap description: “[cpqHoGenericData]” 10004 - cmathreshd Log message: “%s: Variable %s has value %d <= %d.” SNMP trap: cpqMe2FallingAlarm - 10004 in CPQTHRESH.MIB Symptom: Falling Threshold passed.
PAGE 6
 cpqMeAlarmSeverity  cpqMeAlarmExtendedDescription Supporting SNMP trap description: “[cpqMeAlarmOwner]: Variable [cpqMeAlarmVariable] has value [cpqMeAla rmValue] >= [cpqMeAlarmRisingThreshold].” 10006 - cmathreshd Log message: “Falling Threshold Trap” “Alarm Variable %s” “Threshold Value %d” “Alarm Value %d” “Alarm Sample Type %s” “Alarm Owner %s” “Alarm Severity %d” “Alarm Description %s” SNMP trap: cpqMeFallingAlarmExtended - 10006 in CPQTHRSH.MIB Symptom: Falling Threshold passed.
PAGE 7
Supporting SNMP trap data:  sysName  cpqHoTrapFlags  cpqMeAlarmVariable  cpqMeAlarmSampleType  cpqMeAlarmValue  cpqMeAlarmFallingThreshold  cpqMeAlarmOwner  cpqMeAlarmSeverity  cpqMeAlarmExtendedDescription Supporting SNMP trap description: “[cpqMeAlarmOwner]: Variable [cpqMeAlarmVariable] has value [cpqMeAla rmValue] >= [cpqMeAlarmRisingThreshold].” Storage agents Trap IDs: 3016-3047 3016 – cmaidad Log message: “Controller Role Changes: Controller in slot [cpqDaCntlrSlot] is now active.
PAGE 8
Supporting SNMP trap description: “Status is now [cpqDaCntl rBoardStatus].” 3034 - cmaidad Log message: “Logical Drive Status Change: [cpqDaCntl rHwLocation], Drive: [cpqDaLogDrvI ndex]. Status is now [cpqDaLogDrvStatus].” SNMP trap: cpqDa6LogDrvStatusChange - 3034 in CPQIDA.MIB Symptom: Logical Drive Status Change. The agent has detected a change in the status of a drive array logical drive. The variable cpqDaLogDrvStatus indicates the current logical drive status.
PAGE 9
3040 - cmaidad Log message: “Accelerator Board Battery status change, slot number: [cpqDaCntlrSlot]. Battery failed. Status: %s.” SNMP trap: cpqDa6AccelBatteryFailed - 3040 in CPQIDA.MIB Symptom: Accelerator Board Battery Failed. The agent has detected a battery failure associated with the array accelerator cache board. User action: Replace the Accelerator Cache Board.
PAGE 10
User action: If the tape library door is open, close the tape library door.
PAGE 11
 cpqDaTapeDrvLunIndex  cpqDaTapeDrvName  cpqDaTapeDrvFwRev  cpqDaTapeDrvSerialNumber Supporting SNMP trap description: “Cleaning is needed for the tape drive.” 3045 - cmaidad Log message: “Tape Drive Cleaning Tape Needs Replacing, slot number: [cpqDaCntlrSlot], bus number: [cpqDaTapeDrvBusIndex], drive ID: [cpqDaTapeDrvScsiIdIndex]” SNMP trap: cpqDa6TapeDriveCleanTapeReplace - 3045 in CPQIDA.MIB Symptom: Tape Drive Cleaning Tape Needs Replacing.
PAGE 12
User action: If the spare drive status is failed, replace the drive. Supporting SNMP trap data:  sysName  cpqHoTrapFlags  cpqDaCntlrHwLocation  cpqDaSpareCntlrIndex  cpqDaSparePhyDrvIndex  cpqDaSpareStatus  cpqDaSpareLocationString  cpqDaSpareBusNumber Supporting SNMP trap description: “Spare Status is now [cpqDaSpareStatus].” Trap IDs: 5008-5025 5008 - cmascsid Log message: “Tape drive cleaning required: Status is now [cpqTapePhyDrvCondition].
PAGE 13
 cpqTapeLibrarySerialNumber Supporting SNMP trap description: “Tape library [cpqTapeLibrarySerialNumber] door closed” 5018 - cmascsid Log message: “Tape Library Status Changed: Status is now [cpqTapeLibraryState].” SNMP trap: cpqTapeLibraryStatusChange - 5018 in CPQSCSI.MIB Symptom: Tape Library Status Change. The agent has detected a change in the status of a tape library. The current tape library status is indicated in the cpqTapeLibraryState variable.
PAGE 14
 cpqScsiPhyDrvVendor  cpqScsiPhyDrvModel  cpqScsiPhyDrvFWRev  cpqScsiPhyDrvSerialNum  cpqScsiPhyDrvOsName Supporting SNMP trap description: “Status is now [cpqScsiPhyDrvStatus].” 5022 - cmasasd Log message: “SAS Physical Drive Status Changed: Status changed from [previous cpqSasPhyDrvStatus] to [current cpqSasPhyDrvStatus].” SNMP trap: cpqSasPhyDrvStatusChange - 5022 in CPQSCSI.MIB Symptom: Physical Drive Status Change. The agent has detected a change in the status of a SAS or SATA physical drive.
PAGE 15
 sysName  cpqHoTrapFlags  cpqSasHbaHwLocation  cpqSasTapeDrvLocationString  cpqSasTapeDrvHbaIndex  cpqSasTapeDrvIndex  cpqSasTapeDrvName  cpqSasTapeDrvFWRev  cpqSasTapeDrvSerialNumber  cpqSasTapeDrvSasAddress  cpqSasTapeDrvStatus Supporting SNMP trap description: “Status is now [cpqSasPhyDrvStatus].” Trap IDs: 8008-8031 8008 - cmascsid Log message: “Storage system fan status changed to [cpqSsBoxFanStatus string].” SNMP trap: cpqSs3FanStatusChange - 8008 in CPQSTSYS.
PAGE 16
8011 - cmascsid Log message: “Storage system temperature OK.” SNMP trap: cpqSs3TempOk - 8011 in CPQSTSYS.MIB Symptom: Storage system temperature ok. The temperature status has been set to OK. The storage system's temperature has returned to normal operating range. It can be reactivated by the administrator. User action: None Supporting SNMP trap data:  sysName  cpqHoTrapFlags  cpqSsBoxTempStatus Supporting SNMP trap description: “Storage System temperature ok.
PAGE 17
User action: If the UPS status is powerFailed(4) or batteryLow(5), take action to restore power to the UPS. Supporting SNMP trap data:  sysName  cpqHoTrapFlags  cpqSsChassisName  cpqSsChassisTime  cpqSsPowerSupplyBay  cpqSsPowerSupplyUpsStatus Supporting SNMP trap description: “Storage system power supply UPS status changed to [cpqSsPowerSupplyUpsStatus].” 8019 - cmafcad Log message: “Temperature Sensor Status Change.
PAGE 18
Log message: “Power Supply Status Change. Chassis Name: [cpqSsChassisName], Power Supply Status: [cpqSsPowerSu pplyStatus string].” SNMP trap: cpqSsEx2PowerSupplyStatusChange - 8021 in CPQSTSYS.MIB Symptom: Storage system power supply status change. The agent has detected a change in the power supply status of a storage system. The variable cpqSsPowerSupplyStatus indicates the current status. User action: If the power supply status is failed, take action to restore power or replace the failed power supply.
PAGE 19
 cpqSsBackplaneVendor  cpqSsBackplaneModel  cpqSsBackplaneSerialNumber  cpqSsBackplaneTempStatus Supporting SNMP trap description: “Storage system temperature status changed to [cpqSsBackplaneTempStatus].” 8024 - cmafcad Log message: “Backplane Power Status Change. Chassis Name: [cpqSsChassisName], Status: [cpqSsBackplaneFtpsStatus string].” SNMP trap: cpqSsExBackplanePowerSupplyStatusChange - 8024 in CPQSTSYS.MIB Symptom: Storage system power supply status change.
PAGE 20
Supporting SNMP trap data:  sysName  cpqHoTrapFlags  cpqSsBoxCntlrHwLocation  cpqSsBoxCntlrIndex  cpqSsBoxBusIndex  cpqSsBoxVendor  cpqSsBoxModel  cpqSsBoxSerialNumber  cpqSsBoxFanStatus  cpqSsBoxLocationString Supporting SNMP trap description: " Storage box fan status changed: Status changed from [Old cpqSsBoxFanStatus] to [new cpqSsBoxFanStatus].
PAGE 21
 cpqSsBoxModel  cpqSsBoxSerialNumber  cpqSsBoxFltTolPwrSupplyStatus  cpqSsBoxLocationString Supporting SNMP trap description: “Storage box power supply status changed: Status changed from [old cpqSsBoxFltTolPwrSupplyStatus] to [new cpqSsBoxFltTolPwrSupplyStatus]” Trap IDs: 14004-16028 14004 - cmaided Log message: “ATA Disk Status Changes” SNMP trap: cpqIdeAtaDiskStatusChange - 14004 in CPQIDE.MIB Symptom: ATA Disk Status Change. The agent has detected a change in the status of an ATA disk drive.
PAGE 22
 sysName  cpqHoTrapFlags  cpqSsChassisName  cpqSsChassisTime  cpqFcaSpareBusNumber  cpqFcaSpareBay  cpqFcaSpareStatus Supporting SNMP trap description: “Spare Status is now [cpqFcaSpareStatus] on bus [cpqFcaSpareBusNumber].” 16008 - cmafcad Log message: "Status is now %d for tape controller %s." SNMP trap: cpqFcTapeCntlrStatusChange - 16008 in cpqfca.mib Symptom: This trap signifies that the agent has detected a change in the status of a Fiber Channel Tape Controller.
PAGE 23
 cpqSsChassisName  cpqSsChassisTime  cpqFcaPhyDrvBusNumber  cpqFcaPhyDrvBay  cpqFcaPhyDrvStatus  cpqFcaPhyDrvModel  cpqFcaPhyDrvSerialNum  cpqFcaPhyDrvFWRev  cpqFcaPhyDrvFailureCode Supporting SNMP trap description: “Status is now [cpqFcaPhyDrvStatus] for a physical drive on bus [cpqFcaPhyDrvBusNumber], bay [cpqFcaPhyDrvBay].” 16017 - cmafcad Log message: “Accelerator Board status change. Chassis name: [cpqSsChassisName], I/O slot: [cpqFcaAccelBoxIoSlot]. Status is now [cpqFcaAccelStatus string].
PAGE 24
Log message: “Accelerator Board Battery Failed. Chassis name: [cpqSsChassisName], I/O slot: [cpqFcaAccelBoxIoSlot].” SNMP trap: cpqFca2AccelBatteryFailed - 1 601 9 in CPQFCA.MIB Symptom: External Array Accelerator Board Battery Failed. The agent has detected a battery failure associated with the Array Accelerator Cache Board. User action: Replace the Accelerator Cache Board.
PAGE 25
 cpqFcaLogDrvOsName  cpqFcaLogDrvFaultTol  cpqFcaLogDrvSize Supporting SNMP trap description: “Status is now [cpqFcaLogDrvStatus].” 16023 - cmafcad Log message: “Tape Drive Status Change: Status is now [cpqFcTapeDriveStatus] for [cpqFcTapeDriveModel] on port [cpqFcTapeDriveScsi Bus] target [cpqFcTapeDriveScsiTarget].” SNMP trap: cpqExtTapeDriveStatusChange - 16023 in cpqfca.mib Symptom: External Tape Drive Status Change. The agent has detected a change in the status of an External Tape Drive.
PAGE 26
Supporting SNMP trap data:  sysName  cpqHoTrapFlags  cpqFcTapeDriveCntlrIndex  cpqFcTapeDriveScsiBus  cpqFcTapeDriveScsiTarget  cpqFcTapeDriveScsiLun  cpqFcTapeDriveModel  cpqFcTapeDriveFWRev  cpqFcTapeDriveSerialNumber  cpqFcTapeDriveLocation Supporting SNMP trap description: “Cleaning tape needs replacing” 16026 - cmafcad Log message: "Status is now %d for the tape library." SNMP trap: cpqExtTapeLibraryStatusChange - 16026 in cpqfca.mib Symptom: External Tape Library Status Change.
PAGE 27
16028 - cmafcad Log message: “Host controller status change: slot [cpqFcaHostCntlrSlot], status is now [current cpqFcaHostCntlrStatus]” SNMP trap: cpqFca3HostCntlrStatusChange- 16028 in cpqfca.mib Symptom: Fibre Channel Host Controller Status Change. The agent has detected a change in the status of a Fibre Channel Host Controller. The variable cpqFcaHostCntlrStatus indicates the current controller status. User action: If the controller status is failed, replace the controller.
PAGE 28
Supporting SNMP trap description: “Too many memory errors - tracking now disabled.” 6017 - cmahealthd Log message: “The system will be shutdown due to a thermal condition.” SNMP trap: cpqHe3ThermalTempFailed - 601 7 in CPQHLTH.MIB Symptom: The temperature status has been set to Failed. The system will be shut down because of this thermal condition. Supporting SNMP trap data:  sysName  cpqHoTrapFlags Supporting SNMP trap description: “System will be shut down due to this thermal condition.
PAGE 29
6022 - cmahealthd Log message: “A non-operational system fan has returned to normal operation.” SNMP trap: cpqHe3ThermalSystemFanOk – 6022 - CPQHLTH.MIB Log message: "System fan has returned to normal operation." Supporting SNMP trap data:  sysName  cpqHoTrapFlags Supporting SNMP trap description: “System fan has returned to normal operation.” 6023 - cmahealthd Log message: “A processor fan is not operating normally. The system will be shutdown.” SNMP trap: cpqHe3ThermalCpuFanFailed - 6023 in CPQHLTH.
PAGE 30
Symptom: One or more power on self-test (POST) errors occurred. POST errors occur during the server restart process. Supporting SNMP trap data:  sysName  cpqHoTrapFlags Supporting SNMP trap description: “Errors occurred during server restart.” 6028 - cmahealthd Log message: “The server power supply status has become degraded.” SNMP trap: cpqHe3FltTolPwrSupplyDegraded - 6028 in CPQHLTH.MIB Symptom: The fault tolerant power supply sub-system condition has been set to Degraded.
PAGE 31
 sysName  cpqHoTrapFlags  cpqHeFltTol PowerSu pplyChassis  cpqHeFltTolPowerSupplyBay Supporting SNMP trap description: “The Power Supply Removed on Chassis [cpqHeFltTolPowerSupplyChassis], Bay [cpqHeFltTolPowerSupplyBay].” 6035 - cmahealthd Log message: “The redundant fan has degraded.” SNMP trap: cpqHe3FltTolFanDegraded - 6035 in CPQHLTH.MIB Symptom: The fault tolerant fan condition has been set to Degraded for the specified chassis and fan.
PAGE 32
Log message: “The redundant fan was removed.” SNMP trap: cpqHe3FltTolFanRemoved - 6039 in CPQHLTH.MIB Symptom: A fault tolerant fan has been removed from the specified chassis and fan location. Supporting SNMP trap data:  sysName  cpqHoTrapFlags  cpqHeFltTolFanChassis  cpqHeFltTolFanIndex Supporting SNMP trap description: “The Fan Removed on Chassis [cpqHeFltTolFanChassis], Fan [cpqHeFltTolFanIndex].” 6040 - cmahealthd Log message: “The temperature status has failed.
PAGE 33
Symptom: The DC-DC Power Converter condition has been set to Degraded for the specified chassis, slot, and socket. Supporting SNMP trap data:  sysName  cpqHoTrapFlags  cpqHePwrConvChassis  cpqHePwrConvSlot  cpqHePwrConvSocket Supporting SNMP trap description: “The Power Converter Degraded on Chassis [cpqHePwrConvChassis], Slot [cpqHePwrConvSlot], Socket [cpqHePwrConvSocket].” 6044 - cmahealthd Log message: “The DC-DC Power Converter condition has been set to Failed.
PAGE 34
Supporting SNMP trap description: “The Advanced Memory Protection subsystem has engaged the online spare memory.” 6048 - cmahealthd Log message: “The power supply is OK.” SNMP trap: cpqHe4FltTolPowerSupplyOk - 6048 in CPQHLTH.MIB Symptom: The fault tolerant power supply condition has been set back to the OK state for the specified chassis and bay location.
PAGE 35
Supporting SNMP trap data:  sysName  cpqHoTrapFlags  cpqHeFltTol PowerSu pplyChassis  cpqHeFltTolPowerSupplyBay  cpqHeFltTolPowerSupplyStatus  cpqHeFltTolPowerSupplyModel  cpqHeFltTolPowerSupplySerialNumber  cpqHeFltTolPowerSupplyAutoRev  cpqHeFltTolPowerSupplyFirmwareRev  cpqHeFltTolPowerSupplySparePartNum  cpqSiServerSystemId Supporting SNMP trap description: “The Power Supply is Failed on Chassis [cpqHeFltTolPowerSupplyChassis], Bay [cpqHeFltTolPowerSupplyBay], Status [cpqHeFltTolPowerSupplySt
PAGE 36
SNMP trap: cpqHe3FltTolPowerRedundancyRestore - 6054 in CPQHLTH.MIB Symptom: The fault tolerant power supplies have returned to a redundant state for the specified chassis. User action: None required Supporting SNMP trap data:  sysName  cpqHoTrapFlags  cpqHeFltTol PowerSu pplyChassis Supporting SNMP trap description: “The Power Supplies are now redundant on Chassis [cpqHeFltTolPowerSupplyChassis].” 6055 - cmahealthd Log message: "The Fans are now redundant on Chassis %d.
PAGE 37
          sysName cpqHoTrapFlags cpqHeResMem2BoardNum cpqHeResMem2CpuNum cpqHeResMem2RiserNum cpqHeResMem2ModuleNum cpqHeResMem2ModulePartNo cpqHeResMem2ModuleSize cpqSiServerSystemId Supporting SNMP trap description: “Correctable memory errors require a replacement of the memory module in slot [cpqHeResMem2BoardNum], cpu [cpqHeResMem2CpuNum], riser [cpqHeResMem2RiserNum], socket [cpqHeResMem2ModuleNum].
PAGE 38
 Supporting SNMP trap data:  sysName  cpqHoTrapFlags  cpqHeResMem2BoardSlotNum  cpqHeResMem2BoardCpuNum  cpqHeResMem2BoardRiserNum Supporting SNMP trap description: “Memory Board or Cartridge Bus Error Detected in Slot[cpqHeResMem2BoardSlotNum] , Cpu[cpqHeResMem2BoardCpuNum], Riser[cpqHeResMem2BoardRiserNum]." 6068 - cmahealthd Log message: "The Advanced Memory Protection subsystem has engaged the LockStep memory." SNMP trap: cpqHeResilientMemLockStepMemoryEngaged - 6068 in CPQHLTH.
PAGE 39
9004 - cmasm2d Log message: “The Remote Insight Battery has failed and needs to be replaced” SNMP trap: cpqSm2BatteryFailed - 9004 in CPQSM2.MIB Symptom: Remote Insight Battery Failed. The Remote Insight battery has failed and needs to be replaced. Supporting SNMP trap data:  sysName  cpqHoTrapFlags Supporting SNMP trap description: “Remote Insight battery failed.
PAGE 40
Symptom: Mouse Cable Disconnected. The Remote Insight mouse cable was disconnected. Supporting SNMP trap data:  sysName cpqHoTrapFlags Supporting SNMP trap description: “Remote Insight mouse cable disconnected.” 9010 - cmasm2d Log message: “The Remote Insight external power cable has been disconnected” SNMP trap: cpqSm2ExternalPowerCableDisconnected - 9010 in CPQSM2.MIB Symptom: External Power Cable Disconnected. The Remote Insight external power cable was disconnected.
PAGE 41
22003 - cmarackd Log message: “Enclosure removed” SNMP trap: cpqRackEnclosureRemoved - 22003 in CPQRACK.MIB Symptom: The enclosure has been removed. An enclosure has been removed from the rack.
PAGE 42
Supporting SNMP trap description: “The power supply [cpqRackPowerSupplyPosition] in enclosure [cpqRackPowerSupplyEnclosureName] in rack [cpqRackName] has been set to Failed.” 22016 - cmahealthd Log message: “Rack power supply removed” SNMP trap: cpqRackPowerSupplyRemoved - 2201 6 in CPQRACK.MIB Symptom: The power supply has been removed.
PAGE 43
 cpqRackPowerEnclosureName  cpqRackCommonEnclosureSerialNum  cpqRackCommonEnclosu reTrapSequenceNu m Supporting SNMP trap description: “The power subsystem in enclosure [cpqRackPowerEnclosu reName] in rack [cpqRackName] is no longer redundant.” 22019 - cmahealthd Log message: “Rack power supply detected an input voltage problem.” SNMP trap: cpqRackPowerSubsystemLineVoltageProblem - 22019 in CPQRACK.MIB Symptom: The rack power supply detected an input line voltage problem.
PAGE 44
 cpqHoTrapFlags  cpqRackName  cpqRackUid  cpqRackServerBladeEnclosu reName  cpqRackServerBladePosition  cpqRackServerBladeSparePartNumber  cpqRackCommonEnclosureSerialNum  cpqRackCommonEnclosu reTrapSequenceNum Supporting SNMP trap description: “Server power on prevented to preserve redundancy in blade [cpqRackServerBladePosition], in enclosure [cpqRackServerBladeEnclosureName], in rack [cpqRackName].” 22023 - cmahealthd Log message: “Server power on prevented inadequate power to power on.
PAGE 45
User action: Check power enclosure connections or add power supplies. Supporting SNMP trap data:  sysName  cpqHoTrapFlags  cpqRackName  cpqRackUid  cpqRackServerBladeEnclosu reName  cpqRackServerBladePosition  cpqRackServerBladeSparePartNumber  cpqRackCommonEnclosureSerialNum  cpqRackCommonEnclosu reTrapSequenceNu m Supporting SNMP trap description: “Inadequate power to power on blade [cpqRackServerBladePosition], in enclosure [cpqRackServerBladeEnclosureName], in rack [cpqRackName].
PAGE 46
Symptom: Server blade removed. The server blade has been removed from the enclosure.
PAGE 47
[cpqRackCommonEnclosureName], in rack [cpqRackName].” 22031 - cmahealthd Log message: “Power subsystem DC power problem.” SNMP trap: cpqRackPowerChassisDcPowerProblem - 22031 in CPQRACK.MIB Symptom: Power subsystem DC power problem. There is a power subsystem DC power problem for this power enclosure. User action: Check the power enclosure and power supplies. Replace any failed or degraded power supplies.
PAGE 48
Log message: “Power subsystem load balancing wire missing” SNMP trap: cpqRackPowerChassisLoadBalancingWireMissing - 22034 in CPQRACK.MIB Symptom: Power subsystem load balancing wire missing. The power subsystem load balancing wire is missing. User action: Connect the load balancing wire.
PAGE 49
NIC agents Trap IDs: 18001-18014 18001 - cmanicd Log message: “Connectivity is restored for adapter in slot %d, port %d” SNMP trap: cpqNicConnectivityRestored - 1 8001 in CPQNIC.MIB Symptom: This trap is sent any time connectivity is restored to a logical adapter. This occurs when the physical adapter in a single adapter configuration returns to the OK condition or at least one physical adapter in a logical adapter group returns to the OK condition.
PAGE 50
 cpqNicIfPhysAdapterPartNumber  ipAdEntAddr Supporting SNMP trap description: “Connectivity is restored for adapter in slot [cpqNicIfPhysAdapterSlot], port [cpqNicIfPhysAdapterPort].” 18006 - cmanicd Log message: “Connectivity lost for adapter in slot %d, port %d.” SNMP trap: cpqNic2ConnectivityLost – 1 8006 in CPQNIC.MIB Symptom: This trap is sent any time the status of a logical adapter changes to the Failed condition.
PAGE 51
switch failures can also cause this condition. User action: Check the cables to the adapter and the hub or switch. If no cable problems are found, the adapter, hub, or switch might need replacement.
PAGE 52
 cpqNicIfPhysAdapterPartNumber  ipAdEntAddr  cpqNicIfLogMapIPV6Address Supporting SNMP trap description: "Connectivity is restored for adapter in slot [cpqNicIfPhysAdapterSlot], port [cpqNicIfPhysAdapterPort]." 18012 – cmanicd Log message: "Connectivity Lost for adapter in slot %d, port %d." SNMP Trap: cpqNic3ConnectivityLost – 18012 in CPQNIC.MIB Symptom: This trap will be sent any time the status of a logical adapter changes to the Failed condition.
PAGE 53
SNMP Trap: cpqNic3RedundancyReduced – 18014 in CPQNIC.MIB Symptom: This trap will be sent any time a physical adapter in a logical adapter group changes to the Failed condition, but at least one physical adapter remains in the OK condition. This can be caused by loss of link due to a cable being removed from the adapter or the Hub or Switch. Internal adapter, Hub, or Switch failures can also cause this condition. User Action: Check the cables to the adapter and the Hub or Switch.