HP Serviceguard Storage Management Suite Version A.04.01.01 for HP-UX 11i v3 Release Notes

NOTE: When updating from an 11iv2 system containing VxVM 3.5, a message similar to the
following may be displayed:
WARNING: The following was found while selecting software:
- There are new revisions of SW available in the source that would update SW already installed on the system.
The newer revisions are not selected for installation. This will leave the incompatible old revision of SW on
the system. The affected SW is:
- VRTSfspro.FSPRO-PRG,r=4.1x replaces
VRTSfspro.FSPRO-PRG,r=3.5_2_ga08.006
- VRTSfspro,r=4.1x replaces VRTSfspro,r=3.5_2_ga08.006
- VRTSob.VEAS-FILESET,r=3.2.555.1 replaces
VRTSob.VEAS-FILESET,r=3.2.532.0.001
- VRTSob,r=3.2.555.1 replaces VRTSob,r=3.2.532.0.001
- VRTSobgui.VEA-FILESET,r=3.2.555.1 replaces
VRTSobgui.VEA-FILESET,r=3.2.532.0.001
- VRTSobgui,r=3.2.555.1 replaces VRTSobgui,r=3.2.532.0.001
- VRTSvlic.VLIC-RUN,r=3.02.23.1 replaces
VRTSvlic.VLIC-RUN,r=3.01.IA.002.010
- VRTSvlic,r=3.02.23.1 replaces VRTSvlic,r=3.01.IA.002.010
- VRTSvmdoc.VXVM-DOC,r=4.1.032 replaces
VRTSvmdoc.VXVM-DOC,r=3.5~IA.014
- VRTSvmdoc,r=4.1.032 replaces VRTSvmdoc,r=3.5~IA.014
- VRTSvmpro.VMPRO-PRG,r=4.1.020 replaces
VRTSvmpro.VMPRO-PRG,r=3.5~IA.014
- VRTSvmpro,r=4.1.020 replaces VRTSvmpro,r=3.5~IA.014
- VRTSvxvm.VXMS,r=4.1.032 replaces VRTSvxvm.VXMS,r=3.5~IA.014
- VRTSvxvm.VXVM-ENG-A-MAN,r=4.1.032 replaces
VRTSvxvm.VXVM-ENG-A-MAN,r=3.5~IA.014
- VRTSvxvm.VXVM-HELP,r=4.1.032 replaces
VRTSvxvm.VXVM-HELP,r=3.5~IA.014
- VRTSvxvm.VXVM-KRN,r=4.1.032 replaces
VRTSvxvm.VXVM-KRN,r=3.5~IA.014
- VRTSvxvm.VXVM-RUN,r=4.1.032 replaces
VRTSvxvm.VXVM-RUN,r=3.5~IA.014
- VRTSvxvm,r=4.1.032 replaces VRTSvxvm,r=3.5~IA.014
This message can be safely ignored when it refers only to one or more VRTS products. If this
message is displayed in the update-ux interactive TUI (Terminal User Interface), simply press
enter when prompted to do so, and continue with the update.
For rolling upgrades, after installing HP-UX 11i v3 and a SG SMS bundle on a node, the node
will rejoin the cluster automatically.
For offline upgrades, after installing HP-UX 11i v3 and a SG SMS CFS bundle on all nodes, you
can start-up your cluster.
Upgrading a SG SMS OE Bundle - Independent from an HP-UX Update
If the new SG SMS OE bundle version requires new versions of Serviceguard and ECMT, the
Serviceguard and ECMT versions must be updated together with the SG SMS OE bundle upgrade
(Table 7 (page 32) for details). To achieve this, you must build a common installation depot by
copying the relevant software components from SG SMS OE bundle media and copying the
required Serviceguard and ECMT versions from the HP-UX OE media. A single swinstall
command is used for the installation.
For the HP-UX update, Serviceguard and ECMT are excluded from the update when you run the
update-ux command. General information about updating to HP-UX 11i v3 with update-ux
36 HP Serviceguard Storage Management Suite Version A.04.01.01 for HP-UX 11i v3 Release Notes