Using Serviceguard Extension for RAC, 8th Edition, March 2009

# used by any other cluster as a cluster lock device.
# LUN lock disk parameters. Use the CLUSTER_LOCK_LUN parameter
# to define the device on a per node basis. The device may only
# be used for this purpose and by only a single cluster.
#
# Example for a FC storage array cluster disk
# CLUSTER_LOCK_LUN /dev/dsk/c1t2d3s1
# For 11.31 and later versions of HP-UX
# CLUSTER_LOCK_LUN /dev/disk/disk4_p2
# Quorum Server Parameters. Use the QS_HOST, QS_ADDR, QS_POLLING_INTERVAL,
# and QS_TIMEOUT_EXTENSION parameters to define a quorum server. The QS_HOST
# and QS_ADDR are either the host name or IP address of the system that is
# running the quorum server process. More than one IP address can be
# configured for the quorum server. When one subnet fails, Serviceguard
# uses the next available subnet to communicate with the quorum server.
# QS_HOST is used to specify the quorum server and QS_ADDR can be used to
# specify additional IP addresses for the quorum server. The QS_HOST entry
# must be specified (only once) before any other QS parameters. Only
# one QS_ADDR entry is used to specify the additional IP address.
# Both QS_HOST and QS_ADDR should not resolve to the same IP address.
# Otherwise cluster configuration will fail. All subnets must be up
# when you use cmapplyconf and cmquerycl to configure the cluster.
# The QS_POLLING_INTERVAL is the interval (in microseconds) at which
# Serviceguard checks to sure the quorum server is running.
# The optional QS_TIMEOUT_EXTENSION (in microseconds) is used to increase
# the time allocated for quorum server response. The default quorum
# server timeout is calculated primarily from MEMBER_TIMEOUT parameter.
# For cluster of up to 4 nodes it is 0.2*MEMBER_TIMEOUT. It increases
# as number of nodes increases and reaches to 0.5*MEMBER_TIMEOUT for
# 16 nodes
#
# If quorum server is configured on busy network or if quorum server
# polling is experiencing timeouts (syslog messages) or if quorum server
# is used for large number of clusters, such default time (as mentioned
# above) might not be sufficient. In such cases this paramter should be
# use to provide more time for quorum server.
# Also this parameter deserves more consideration if small values
# for MEMBER_TIMEOUT is used.
#
# The value of QS_TIMEOUT_EXTENSION will directly effect the amount of
# time it takes for cluster reformation in the event of node failure. For
# example, if QS_TIMEOUT_EXTENSION is set to 10 seconds, the cluster
# reformation will take 10 seconds longer than if the QS_TIMEOUT_EXTENSION
# was set to 0. This delay applies even if there is no delay incontacting
# the Quorum Server.#
# The recommended value for QS_TIMEOUT_EXTENSION is 0 (the default value),
# and the maximum supported value is 300000000 (5 minutes).
#
# For example, to configure a quorum server running on node "qs_host"
# with the additional IP address "qs_addr" and with 120 seconds for the
# QS_POLLING_INTERVAL and to add 2 seconds to the system assigned value
# for the quorum server timeout, enter
#
# QS_HOST qs_host
# QS_ADDR qs_addr
# QS_POLLING_INTERVAL 120000000
# QS_TIMEOUT_EXTENSION 2000000
QS_HOST hpq21
QS_POLLING_INTERVAL 300000000
# Definition of nodes in the cluster.
# Repeat node definitions as necessary for additional nodes.
# NODE_NAME is the specified nodename in the cluster.
# It must match the hostname and both cannot contain full domain name.
# Each NETWORK_INTERFACE, if configured with IPv4 address,
# must have ONLY one IPv4 address entry with it which could
# be either HEARTBEAT_IP or STATIONARY_IP.
# Each NETWORK_INTERFACE, if configured with IPv6 address(es)
# can have multiple IPv6 address entries(up to a maximum of 2,
# only one IPv6 address entry belonging to site-local scope
# and only one belonging to global scope) which could be
# either HEARTBEAT_IP or STATIONARY_IP.
# Note: This configuration contains IPv6 addresses.
# To obtain an IPv4-only cluster configuration, comment out
# the IPv6 addresses if there are IPv4 STATIONARY_IPs
# or HEARTBEAT_IPs configured on the same interface. Otherwise
Cluster Configuration ASCII File 49