HP XP24000/XP20000 Remote Web Console Error Codes Abstract This document lists the error codes and error messages for HP Remote Web Console for HP XP disk arrays, and provides recommended action for the error conditions.
© Copyright 2007, 2011 Hewlett-Packard Development Company, L.P. Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor's standard commercial license. The information contained herein is subject to change without notice.
Contents 1 Remote Web Console for Storage System Messages and Error Codes................4 Remote Web Console for Storage System Messages......................................................................4 Message Window Format..........................................................................................................4 Remote Web Console Error Codes..............................................................................................5 2 Support and Other Resources..................
1 Remote Web Console for Storage System Messages and Error Codes • “Remote Web Console for Storage System Messages” (page 4) • “Message Window Format” (page 4) • “Remote Web Console Error Codes” (page 5) Unless otherwise specified, the term storage system in this guide refers to the following disk arrays: • HP XP24000 Disk Array • HP XP20000 Disk Array The GUI illustrations in this guide were created using a Windows computer with the Internet Explorer browser.
The server is unable to accept the request from Remote Web Console. One possible cause is that some process is in progress at the server. This message does not indicate an error. • Message text: Descriptive text that appears in the message window. It may include variables %s (character string) and %d (numeral). The values of these variables are determined when processing is performed.
• 4: To make refresh possible • 5: No status change • 6: No change with refreshing automatically • 7: Remote Web Console is automatically switched to view mode. If necessary, change the mode to Modify. Table 1 Error Codes — Part Code 0001 6 Part Code Error Number Error Message 0001 1000 0001 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 1 Error Codes — Part Code 0001 (continued) Part Code Error Number Error Message Severity Level Failure Level 0001 3001 The number of set operations Reduce the number of set exceeds the maximum operations and perform (20000). again. E 6 0001 3002 An error occurred during SVP If this problem persists call HP E processing. If this problem technical support. persists, call HP technical support. 2 0001 4001 An error occurred during SVP If this problem persists call HP E processing.
Table 1 Error Codes — Part Code 0001 (continued) Part Code Error Number Error Message Recommended Action 0001 4020 Network error detected; exclusive lock is released. Lock is removed. Lock again. E 0001 5013 An error occurred during SVP If the same problem persists processing. If this problem despite retrying, call HP persists, call HP technical technical support. support. E 2 0001 5014 The user ID or password is invalid.
Table 1 Error Codes — Part Code 0001 (continued) Part Code Error Number Error Message 0001 5514 0001 Recommended Action Severity Level Failure Level An error occurred during SVP If the same problem persists processing. If this problem despite retrying, call HP persists, call HP technical technical support. support. E 2 5515 An error occurred during SVP If the same problem persists processing. If this problem despite retrying, call HP persists, call HP technical technical support. support.
Table 1 Error Codes — Part Code 0001 (continued) 10 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0001 5553 The user name is not set. Check the setting, and then retry the operation. The user name is not set. Check the setting, and then retry the operation. E 2 0001 5554 An administrator cannot be Check the setting, and then added or deleted. Check the retry the operation. setting, and then retry the operation.
Table 1 Error Codes — Part Code 0001 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level persists, call HP technical support. 0001 5814 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 0001 6002 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 1 Error Codes — Part Code 0001 (continued) Part Code 12 Error Number Error Message Recommended Action cause of the problem. Contact your network administrator. If your network is not having any problems, and if this problem persists, call HP technical support. persists and you use a proxy server, the old version of the program might be in the cache of the proxy. Contact your network administrator to clear the proxy cache.
Table 1 Error Codes — Part Code 0001 (continued) Part Code Error Number Error Message 0001 56551 0001 Recommended Action Severity Level Failure Level Failed to connect to the FTP Check the IP address, or the server. Check the IP address, connection between the SVP or the connection between and the FTP server. the SVP and the FTP server. W 5 56552 The file transfer to the FTP Check the setting. server failed. Check the user ID and the password.
Table 1 Error Codes — Part Code 0001 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Severity Level Failure Level Edition version information Edition version information and then retry the operation. and then retry the operation. Table 2 Error Codes — Part Code 0002 Part Code Error Number Error Message Recommended Action 0002 1025 The specified LU path does not exist. Check the setting. The configuration information E has already been changed.
Table 2 Error Codes — Part Code 0002 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Call HP technical support. persists, call HP technical support. 0002 2011 The server configuration is invalid. Call HP technical support. E 2 0002 2012 An error occurred during SVP If this problem persists call HP E processing. If this problem technical support. persists, call HP technical support.
Table 2 Error Codes — Part Code 0002 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Wait a few seconds and login again. 16 0002 5513 You cannot delete paths and Delete paths and host groups E host groups at the same time. separately. 6 0002 6000 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 2 Error Codes — Part Code 0002 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level persists, call HP technical support. 0002 7211 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 0002 8005 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 3 Error Codes — Part Code 0003 18 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0003 1003 You are trying to set multiple The configuration information E paths to the same volume has been already changed. from one group. Check the settings, and request the setting of the configuration information again. 6 0003 1004 Multiple volumes are specified to a single port, group or LUN combination. The configuration information E has been changed already.
Table 3 Error Codes — Part Code 0003 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level cannot be processed in this agent. The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact HP technical support. 0003 1020 An error occurred. If this problem persists, call HP technical support. LUN is invalid. (The specified E value is not in the specification.
Table 3 Error Codes — Part Code 0003 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level normally because it is guarded in the screen. In the unlikely event that this error occurs, contact HP technical support. 20 0003 1028 The number of volumes you intend to combine into a LUSE volume exceeds the maximum. The configuration information E has been already changed. Check the settings and request the setting of the configuration information again.
Table 3 Error Codes — Part Code 0003 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level screen. In the unlikely event that this error occurs, contact HP technical support. 0003 1039 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 0003 1040 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support.
Table 3 Error Codes — Part Code 0003 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level error occurs, contact HP technical support. 22 0003 1061 Security Switch Off operation and path adding operation cannot be performed simultaneously. Check the current configuration and then make settings again. First, add paths, and then E click Apply. Next, turn off the security switch, and then click Apply.
Table 3 Error Codes — Part Code 0003 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0003 1101 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 0003 1102 Volume initialization operation cannot include the last LDEV of RAID striping group. Because at least one LDEV is E required in the parity group, you cannot uninstall anymore.
Table 3 Error Codes — Part Code 0003 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level You cannot do any of the The following settings are following to the same volume: invalid. 1. Set command device + • Specify the volume as a Release command device command device and security disable command device 2. Release command device security on the volume.
Table 3 Error Codes — Part Code 0003 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0003 1131 No more host groups can be set, because the number of host groups has reached the maximum (254) that can be set in a port. No more host groups can be E set, because the number of host groups has reached the maximum (254) that can be set in a port. Reduce the number of host groups, and then retry the operation.
Table 3 Error Codes — Part Code 0003 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Log in again after a while. W 2 impossible to change. Release the Port Group setting. 26 0003 1141 Processing in progress. Please wait for a while, and then retry the operation. 0003 1154 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 3 Error Codes — Part Code 0003 (continued) Part Code Error Number Error Message Recommended Action 0003 1184 The port information is inconsistent with PCB mode information. Correct the port information W or the PCB mode information. 0 0003 1185 You are trying to insert in the linkage operation including LUSE. (LDEV number is inserted to the LDEV numbers created in LUSE). The configuration information E has been already changed.
Table 3 Error Codes — Part Code 0003 (continued) 28 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0003 1358 Cache Residency cannot be set to the specified volume because the IO Suppression mode is set to Enable. Disable the IO Suppression mode of this volume, and then retry the operation, or remove the volume from the volumes to be set. E 2 0003 1359 Cache Residency cannot be set for this volume because its Cache mode is set to Disable.
Table 3 Error Codes — Part Code 0003 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0003 1900 Maintenance operation is being executed by the SVP. Wait for the maintenance to complete, and then retry the operation. Wait for the maintenance to complete, and then retry the operation. E 6 0003 1904 The specified volume cannot Select another volume.
Table 3 Error Codes — Part Code 0003 (continued) Part Code Error Number Error Message 0003 2001 0003 0003 Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 2002 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 2003 Auto LUN, QuickRestore, etc. are in process.
Table 3 Error Codes — Part Code 0003 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level persists, call HP technical support. 0003 2013 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 0003 2014 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 3 Error Codes — Part Code 0003 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level the status of the path to the external volume. 32 0003 2082 Processing is disabled because the host is mounted or the device is reserved. The host is mounted or the device is reserved. Unmount the host and cancel reservation of the device. If the host is an AIX host, unmount the host, and execute the varyoffvg command.
Table 3 Error Codes — Part Code 0003 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level XP exist. Either release the settings or stop the I/Os, and then retry the operation. 0003 2091 The backup server of Business Stop the backup server, and Copy, ShadowImage for then retry. Mainframe, or Compatible FlashCopy(R) is running. Please stop the backup server and then retry the operation.
Table 3 Error Codes — Part Code 0003 (continued) 34 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0003 2097 The host specified by the WWN is performing I/O operations. Stop executing I/Os, and then retry the operation. E 6 0003 2098 The operation cannot be performed, because the SVP microcode version does not match the DKCMAIN (subsystem) microcode version. Call HP technical support, when the same problem persists.
Table 3 Error Codes — Part Code 0003 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level does not have Read/Write attribute. 0003 2502 The LUs cannot be combined Correct settings, and then or released because the retry. volumes don't have Read/Write attribute. E 6 0003 2503 The LUs cannot be combined Correct settings, and then or released because the retry. volumes don't have Read/Write attribute.
Table 3 Error Codes — Part Code 0003 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level reserved volume, and then retry the operation. 0003 3000 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 0003 3001 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 4 Error Codes — Part Code 0004 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level persists, call HP technical support. 0004 6003 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 0004 6010 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 5 Error Codes — Part Code 0005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0005 8401 The subsystem status is invalid. Call HP technical support. Retry the same operation E several times. If the same error occurs, call HP technical support. 2 0005 66101 This function could not be used because a function failed to start during SVP initialization. Click [All Refresh] and refresh E the configuration.
Table 7 Error Codes — Part Code 0007 (continued) Part Code Error Number Error Message 0007 5302 0007 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 5303 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 7 Error Codes — Part Code 0007 (continued) Part Code Error Number Error Message 0007 6023 File access error occurred. Recommended Action Severity Level If a file is transferred between E If a file is transferred between the SVP and client PC, confirm that the file name SVP and client PC, confirm does not contain any invalid that the file name does not characters. contain invalid characters. The characters that can be In other cases, wait for a while and retry the operation.
Table 8 Error Codes — Part Code 0010 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level The version of Remote Web Console may not match the version of the destination SVP. Clear the cache of JRE and the browser, restart the browser, and then retry the processing. Remote Web Console is downloaded over your network and then executed.
Table 8 Error Codes — Part Code 0010 (continued) 42 Part Code Error Number Error Message 0010 56001 0010 Recommended Action Severity Level Failure Level An error occurred during the If this problem persists, call I/O processing of a HP technical support. temporary file. If this problem persists, call HP technical support. E 2 56002 An error occurred during the If this problem persists, call I/O processing of a HP technical support. temporary file.
Table 9 Error Codes — Part Code 0105 Part Code Error Number Error Message 0105 1904 0105 Recommended Action Severity Level Failure Level The specified volume cannot Select another volume. be assigned as a LUSE volume or a command device, and the path of the volume cannot be set because it is being used as a Pool volume. E 6 1905 There are virtual volumes and Select another volume. non-virtual volumes in the volumes specified to compose a LUSE volume.
Table 9 Error Codes — Part Code 0105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0105 2089 The corresponding CHA Be sure there is an alternate might contain the last path path from the MCU. between the MCU and the RCU of XP Continuous Access. Make sure that there is an alternate path from the MCU. W 6 0105 2090 Business Copy, ShadowImage for Mainframe, Compatible FlashCopy(R), or Flex Copy XP settings exist.
Table 9 Error Codes — Part Code 0105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level • LDEV shredding is in progress • Extent shredding is in progress Therefore the specified operation cannot be executed. 0105 2200 The Concurrent Copy or the Compatible XRC operation is in progress in the target volumes. Cancel the Concurrent Copy job or delete an Compatible XRC pair via the host.
Table 9 Error Codes — Part Code 0105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Universal Replicator for Mainframe pair. Alternatively, command devices defined by Business Continuity Manager are included. Release the pair definition or delete command devices defined by Business Continuity Manager, and then retry the operation.
Table 9 Error Codes — Part Code 0105 (continued) Part Code Error Number Error Message 0105 3003 0105 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 5013 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 9 Error Codes — Part Code 0105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level and the SVP microcode version are mismatched. 0105 8979 The operation of the external volume has been failed because all the paths to the external volume are blocked. Restore more than one path E to the external volume, and then perform the operation of the external volume.
Table 10 Error Codes — Part Code 0110 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0110 2033 The SVP is not ready yet, or Wait a few seconds, and an internal processing is in then log on again. progress. Please wait for a while, and then log on again. W 1 0110 5030 No data is set for the SVP registration. Set the things required to be W registered, and then retry the operation. 5 0110 5081 The license for this product (%s) will expire in %d days.
Table 10 Error Codes — Part Code 0110 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level IP address is correct, close the browser (also close the browser of the storage list), and log in again. 50 0110 7060 A client processing error occurred. Call HP technical support. E 2 0110 7440 An error occurred during processing. If this problem persists call HP technical support. If this problem persists, call HP technical support.
Table 10 Error Codes — Part Code 0110 (continued) Part Code Error Number Error Message 0110 55604 0110 Recommended Action Severity Level Failure Level There are no valid program Contact the storage products. Contact the storage administrator and request to administrator and request to allocate the license of SLPR. allocate the license of SLPR. E 1 56503 The unsupported JRE version Install the supported version is used. Install the supported of JRE. version of JRE, and then retry the operation.
Table 10 Error Codes — Part Code 0110 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level window you wish to display from the [Go] menu. 0110 67005 Configuration information on Click [Refresh All] on the File E the storage system and the menu and refresh the configuration information on configuration information. the SVP became inconsistent. Click [Refresh All] on the File menu and refresh the configuration information.
Table 11 Error Codes — Part Code 0190 (continued) Part Code Error Number Error Message Recommended Action Severity Level 0190 5013 Enter the product name with up to 16 alphanumeric characters. Specify the product name using up to 16 characters or less and retry. 0190 5014 Enter the location name with Specify the location name up to 16 alphanumeric using up to 16 characters or characters. less and retry. 0190 5015 Enter the serial no. with a number fewer than 65536.
Table 11 Error Codes — Part Code 0190 (continued) 54 Part Code Error Number Error Message Recommended Action 0190 6003 The storage list file does not exist. Call HP technical support. 0190 6004 Failed to open the storage list If the same error occurs again file. despite retrying, call HP technical support. 0190 6005 The storage list file does not exist. Call HP technical support. 0190 6010 The storage list file does not exist. Call HP technical support.
Table 12 Error Codes — Part Code 0210 Part Code Error Number Error Message 0210 7060 0210 Recommended Action Severity Level Failure Level An error occurred in the client Call HP technical support. logic. E 2 55605 The specified user ID or password is invalid. Specify a valid user ID or password. W 5 0210 55606 Enter the user ID. Enter the user ID. W 5 0210 55607 Enter the user ID with up to Enter a correct user ID. 16 alphanumeric characters.
Table 12 Error Codes — Part Code 0210 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0210 55624 Are you sure you want to register the parameters? To register the parameters, click [OK]. Otherwise, click [Cancel]. W 5 0210 55625 Are you sure you want to To change the write change the write permission? permission, click [OK]. Otherwise, click [Cancel].
Table 13 Error Codes — Part Code 0290 (continued) Part Code Error Number Error Message Recommended Action Severity Level 0290 5030 You cannot use the following Remove the invalid characters characters: " # & = + \ , ; : and retry. *?<>|/ 0290 5040 You cannot use multi-byte characters. Remove the multi-byte characters and retry. 0290 5050 The user ID is already registered. Register the other user ID. 0290 5060 The number of user accounts You cannot register anymore. exceeds the maximum.
Table 13 Error Codes — Part Code 0290 (continued) 58 Part Code Error Number Error Message Recommended Action 0290 6070 Failed to restore the user account list file. Call HP technical support. 0290 6080 Failed to open the user account list file. If the same error occurs again despite retrying, call HP technical support. 0290 6090 Failed to back up the user account list file. Call HP technical support. 0290 6091 An error occurred while compressing a file. Call HP technical support.
Table 13 Error Codes — Part Code 0290 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level while you were making settings. 0290 6250 The user account list was Terminate the process and modified by the administrator contact the administrator. while you were making settings. 0290 6260 Failed to open the user account list file. If the same error occurs again despite retrying, call HP technical support. 0290 6270 Failed to open the environment file.
Table 13 Error Codes — Part Code 0290 (continued) 60 Part Code Error Number Error Message Recommended Action 0290 56221 File Name is invalid. Specify the correct file name, and then retry the operation. 0290 56231 File Name is invalid. Specify the correct file name, and then retry the operation. 0290 56241 File Name is invalid. Specify the correct file name, and then retry the operation. 0290 56301 No checkbox is checked. Check more than one check box, and then retry the operation.
Table 13 Error Codes — Part Code 0290 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0290 56621 Failed to create the file. If this problem persists, call HP technical support. 0290 56631 Failed to create the file. If this problem persists, call HP technical support. 0290 56791 Failed to delete work files. If this problem persists, call HP technical support. 0290 56792 Failed to delete work files.
Table 14 Error Codes — Part Code 0305 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level persists, call HP technical support. 0305 7203 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 0305 7204 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 14 Error Codes — Part Code 0305 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0305 65685 0 cannot be specified in all the fields. Correct the settings, and then W retry the operation. 5 0305 65686 The SVP OS does not support Correct the settings, and then W IPv6. retry the operation.
Table 16 Error Codes — Part Code 0405 Part Code Error Number Error Message 0405 5013 0405 Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 5047 An error occurred when installing or uninstalling the program product. Select the program product and select [Detail] to check the details of the error. W 5 0405 5070 The product name is different.
Table 16 Error Codes — Part Code 0405 (continued) Part Code Error Number Error Message Recommended Action Disaster Recovery Extended Universal Replicator for Mainframe Disaster Recovery Extended XP Continuous Access Journal XP Compatible Hyper PAV XP Compatible Hyper PAV Severity Level Failure Level 0405 5074 The specified PP ID is invalid. Retry again. If it occurred again, call HP technical support. W 5 0405 5075 This key code is invalid. Confirm if the key code is correct or not.
Table 16 Error Codes — Part Code 0405 (continued) Part Code 0405 Error Number 5078 Error Message Recommended Action Disaster Recovery Extended Universal Replicator for Mainframe Disaster Recovery Extended XP Continuous Access Journal XP Compatible Hyper PAV XP Compatible Hyper PAV To uninstall this program product, you must uninstall another program product first. Program Product Name To uninstall this program W product, you should uninstall another program product first.
Table 16 Error Codes — Part Code 0405 (continued) Part Code Error Number Error Message XP Compatible Hyper PAV Recommended Action Severity Level Failure Level XP Compatible Hyper PAV 0405 5079 This program product needs another DKC type. Call HP technical support. W 5 0405 5080 You cannot change this program product. Call HP technical support. W 5 0405 5087 Since the error occurred in Select except ALL Normal. another P.P., this P.P. was not processed.
Table 16 Error Codes — Part Code 0405 (continued) 68 Part Code Error Number Error Message 0405 7060 0405 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 7061 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 16 Error Codes — Part Code 0405 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level persists, call HP technical support. 0405 8002 An error occurred during SVP processing. If this problem persists, call HP technical support. Isolate the abnormal section following the procedure below: 1. Rebooting the computer 2. Checking the LAN card/LAN cable 3. Checking the IP address of the computer 4. Replacing the computer 5.
Table 16 Error Codes — Part Code 0405 (continued) Part Code 70 Error Number Error Message Recommended Action uninstalled, because the license for it is allocated to the SLPR. uninstall the program product. Severity Level Failure Level 0405 55506 Since the licensed capacity of SLPR0 is insufficient, the partition capacity can't be increased. Check the licensed capacity of SLPR0. E 6 0405 55520 It is not possible to install it because of PP of pre-install.
Table 16 Error Codes — Part Code 0405 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Allocate the licensed capacity to use it continuously. If capacity is not allocated within 30 days, the license of the SLPR becomes invalid. 0405 65090 The licensed capacity to be installed is insufficient. Increase the licensed E capacity and install it again. Or, delete the licensed capacity of unnecessary SLPR.
Table 18 Error Codes — Part Code 0410 (continued) Part Code Error Number Error Message 0410 55000 0410 0410 Recommended Action Severity Level Failure Level Since the error occurred in Acquire the information the install or uninstall judging, again, and retry the the applying operation operation. cannot be performed. W 0 55001 The length of the key code is Check the length of the key incorrect. code.
Table 18 Error Codes — Part Code 0410 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level the subsystem or the licensed capacity. 0410 59307 Do you want to discard the change and restore the setting? Click [OK] to restore the setting. i 5 0410 59317 The setting of the program product has been changed. Be sure to back up the configuration information. Click [OK].
Table 19 Error Codes — Part Code 0505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level persists, call HP technical support. 0505 6502 A time-out error occurred. Wait for a while, and then retry the operation. If this problem persists, call HP technical support. Wait a few seconds, and retry the operation. W 6 0505 6506 Communication busy. Retry later. Wait a few seconds, and retry the operation.
Table 19 Error Codes — Part Code 0505 (continued) Part Code Error Number Error Message Recommended Action 0505 8401 The status of the storage system requires maintenance (for example, the subsystem is blocked, the shared memory is inconsistent, or some other problem occurs). Check the status of the disk W storage system (for example, the storage system is blocked, the shared memory is inconsistent, or some other problem occurs). If this problem persists, call HP technical support.
Table 22 Error Codes — Part Code 0605 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0605 2011 The status of the storage system requires the maintenance (for example, the subsystem is blocked, the shared memory is inconsistent, or some other factor). Call HP technical support. Check the status of the disk W storage system (if the storage system is blocked, inconsistency of shared memory, or some other factor).
Table 22 Error Codes — Part Code 0605 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level W 3 Cancel the Concurrent Copy Concurrent Copy job or job or delete a Compatible delete a Compatible XRC XRC pair via the host. pair via the host. If the Concurrent Copy or the Compatible XRC operation is not in progress in the target volumes, issue the LISTSESS and LISTDVCS commands, check the SESSION ID No., and terminate SESSION by means of the TERMSESS command.
Table 22 Error Codes — Part Code 0605 (continued) 78 Part Code Error Number Error Message Recommended Action 0605 2517 A Business Copy, ShadowImage for Mainframe, Compatible FlashCopy(R), or XP Snapshot pair is defined. Cancel the pair definition, and then retry the operation. When quick split is in process, suspend and then cancel the pair. Cancel the pair definition, E and then retry the operation. When high-speed split is in process, suspend, and then cancel the pair.
Table 22 Error Codes — Part Code 0605 (continued) Part Code Error Number Error Message 0605 5828 0605 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 6012 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 22 Error Codes — Part Code 0605 (continued) 80 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0605 8100 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 0605 8102 This function is not supported. Check whether the E DKCMAIN microcode version and the SVP microcode version are mismatched. 3 0605 8122 This logical volume is busy.
Table 22 Error Codes — Part Code 0605 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0605 8958 An error occurred on the DKC side. If this problem persists, call HP technical support. An error occurred on the DKC side. If this problem persists, call HP technical support. E 3 0605 8959 An error occurred on the DKC side. If this problem persists, call HP technical support. An error occurred on the DKC side.
Table 22 Error Codes — Part Code 0605 (continued) 82 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0605 8970 An error occurred on the DKC side. If this problem persists, call HP technical support. An error occurred on the DKC side. If this problem persists, call HP technical support. E 3 0605 8971 An error occurred while connecting to the storage system. The configuration may be inconsistent.
Table 22 Error Codes — Part Code 0605 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0605 56514 The capacity of the specified Check the capacity of the volume is less than the volume. minimum required to perform the Add Volume operation. E 5 0605 56515 Execute the Disconnect Subsystem command or the Disconnect Volume command for the volume.
Table 22 Error Codes — Part Code 0605 (continued) 84 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0605 57101 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 0605 58246 This function is not supported. Check whether the E DKCMAIN microcode version and the SVP microcode version are mismatched.
Table 22 Error Codes — Part Code 0605 (continued) Part Code Error Number Error Message Recommended Action Severity Level Set the same cache mode to the volumes which compose the LUSE volume. Set the same cache mode to the volumes which compose the LUSE volume. Failure Level 0605 58573 This function is not supported. Check whether the E DKCMAIN microcode version and the SVP microcode version are mismatched.
Table 22 Error Codes — Part Code 0605 (continued) 86 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0605 65796 The specified PathGroup number has already been used as a parameter of PathGroup. Check the contents of the spreadsheet. E 5 0605 65797 The specified PathGroup number has already been used as a parameter of TargetPathGroup. Check the contents of the spreadsheet.
Table 22 Error Codes — Part Code 0605 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0605 66502 The definition of Exg is duplicated. Check the contents of the spreadsheet. E 5 0605 66503 The definition of volume is invalid. Check the contents of the spreadsheet. E 5 0605 66504 The definition of volume is duplicated. Check the contents of the spreadsheet.
Table 22 Error Codes — Part Code 0605 (continued) 88 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0605 66675 The syntax of the definition statement is invalid. Check the contents of the spreadsheet. E 5 0605 66692 The volume in the local storage system cannot be operated. Specify the volume in an external storage system. E 5 0605 66693 A correct parameter is not set See the HP E as a data transfer volume.
Table 22 Error Codes — Part Code 0605 (continued) Part Code Error Number Error Message 0605 66709 0605 Recommended Action Severity Level Failure Level The format of LUN is invalid. Check the contents of the spreadsheet. E 5 66710 The value entered as LUN is outside the setting range. Check the contents of the spreadsheet. E 5 0605 66711 The number of digits of Exg is invalid. Check the contents of the spreadsheet. E 5 0605 66712 The format of Exg is invalid.
Table 22 Error Codes — Part Code 0605 (continued) 90 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0605 66739 The value entered as CU is outside the setting range. Check the contents of the spreadsheet. E 5 0605 66740 The number of digits of LDEV Check the contents of the is invalid. spreadsheet. E 5 0605 66741 The format of LDEV is invalid. Check the contents of the spreadsheet.
Table 22 Error Codes — Part Code 0605 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Group are included in the includes the items to be items to be maintained. maintained. Delete the XP Thin Provisioning Pool Group that includes the items to be maintained. 0605 68734 The pool volumes associated with the XP Thin Provisioning volume is included in the items to be maintained.
Table 22 Error Codes — Part Code 0605 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level located in the system disk option window of VLL. 0605 68866 The volume targeted for maintenance includes a system disk being used by the Additional configuration Back up. The volume targeted for E maintenance includes a system disk being used by the Additional configuration Back up.
Table 23 Error Codes — Part Code 0610 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0610 7060 An error occurred during processing. If this problem persists, call HP technical support. If this problem persists, call HP technical support. E 2 0610 7111 An error occurred during processing. If this problem persists, call HP technical support. If this problem persists, call HP technical support. E 2 0610 9005 An error occurred.
Table 23 Error Codes — Part Code 0610 (continued) Part Code Error Number Error Message 0610 59022 0610 Recommended Action Severity Level Failure Level There are not enough logical Decrease the number of volumes to perform the external volumes to be mapping operation. mapped, and then retry the operation. i 0 59029 The Check Paths processing began. After three minutes, click [Refresh] on the File menu to check the path status.
Table 23 Error Codes — Part Code 0610 (continued) Part Code Error Number Error Message Recommended Action Severity Level 0610 59058 Do you want to specify an SSID without restrictions on SLPRs? To continue processing, click i [OK]. Otherwise, click [Cancel]. 0 0610 59060 The entered numerical value is outside the setting range. Check the setting range, and i enter a correct numerical value.
Table 23 Error Codes — Part Code 0610 (continued) Part Code Error Number Error Message 0610 69006 0610 0610 Recommended Action Severity Level Failure Level There is an external volume Complete the parameter that the parameter setting is setting of all external not completed. Complete the volumes. parameter setting of all external volumes. W 0 69008 An emulation type cannot be Set the emulation type that applied is specified.
Table 23 Error Codes — Part Code 0610 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0610 69027 A CLPR number cannot be applied for [Set External Volume Parameter] dialog box or [Edit Policy] dialog box is specified. Specify the CLPR number that E can be applied for [Set External Volume Parameter] dialog box or [Edit Policy] dialog box and retry the operation.
Table 26 Error Codes — Part Code 1005 Part Code Error Number Error Message Recommended Action 1005 1002 The specified volume cannot Select another volume. be set as a command device or a component of a LUSE volume, because it is being used as the volume of XP Continuous Access, Business Copy, Auto LUN, or XP Snapshot. Severity Level Failure Level E 6 Please select another volume.
Table 26 Error Codes — Part Code 1005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level unlikely event that this error occurs, contact HP technical support. 1005 1012 LU path is set to a volume which links as an expanded LU. The configuration information E has been already changed. 6 Check the settings, and request the setting of the configuration information again.
Table 26 Error Codes — Part Code 1005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 1005 1022 An error occurred. If this problem persists, call HP technical support. Host mode is invalid. (The E specified value is not in the specification.) The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact HP technical support. 2 1005 1023 An error occurred.
Table 26 Error Codes — Part Code 1005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level current configuration and then make settings again. 1005 1063 The specified WWN is already in use. Specify another WWN. Correct the specified contents, E and request the setting of the configuration information again. 6 1005 1064 You are trying to register the same WWN as the already registered one.
Table 26 Error Codes — Part Code 1005 (continued) Part Code Error Number Error Message Recommended Action 1005 1111 An error occurred. If this problem persists, call HP technical support. A nickname is not specified E when the configuration change of LUN Manager is requested. The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact HP technical support. 2 1005 1116 An error occurred.
Table 26 Error Codes — Part Code 1005 (continued) Part Code Error Number Error Message Recommended Action 1005 1131 No more host groups can be set, because the number of host groups has reached the maximum (254) that can be set in a port. No more host groups can be E set, because the number of host groups has reached the maximum (254) that can be set in a port. Reduce the number of host groups, and then retry the operation.
Table 26 Error Codes — Part Code 1005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 1005 1140 Because the Port Group setting is done, it is impossible to change. Release the Port Group setting. Release the Port Group setting. E 2 1005 1170 The volume cannot be configured as a command device because the volume does not have Read/Write attribute. Correct settings, and then retry. E 6 1005 1174 The specified host ID is already registered.
Table 26 Error Codes — Part Code 1005 (continued) Part Code Error Number Error Message 1005 1190 To define a path to the Correct the settings, and then E volume from an iSCSI port, retry the operation. the volume must be read/write-enabled and also usable as an S-VOL (secondary volume). 6 1005 1194 No information can be Correct the settings, and then E changed about this external retry. port because the port has an external volume.
Table 26 Error Codes — Part Code 1005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level damage to the logical paths. delete the logical path, and Please stop this operation. If then retry the port setting. you want to continue this operation, please remove the logical paths from the MCU port first. 1005 1353 S-VOLs remain on the Fibre-RCU port. This operation may cause a fatal damage to S-VOLs. Please stop this operation.
Table 26 Error Codes — Part Code 1005 (continued) Part Code Error Number Error Message 1005 1368 1005 Recommended Action Severity Level Failure Level The host mode “4C” can only Check the settings, and then be used with External Storage retry. volumes. E 6 1369 The specified host mode option can be set only for a specific port attribute. Check the setting of the host mode option. W 3 1005 1600 This functionality is not available. LUN Manager is required.
Table 26 Error Codes — Part Code 1005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 1005 1927 The specified volume cannot Check the setting. be set as a command device, because it is being used as a quorum disk. E 6 1005 1928 Addition or deletion of paths for LUN0 cannot be done because Host Mode Option 60 is set to ON. Also, setting change of Host Mode Option 60 and path change (addition or deletion) for LUN0 cannot be done at the same time.
Table 26 Error Codes — Part Code 1005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level necessary, re-execute the setting operation. 1005 2097 The host specified by the WWN is performing I/O operations. Stop executing I/Os, and then retry the operation. E 6 1005 2098 The operation cannot be performed, because the SVP microcode version does not match the DKCMAIN (subsystem) microcode version.
Table 26 Error Codes — Part Code 1005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 1005 4436 An error occurred. Click [Refresh All] on the [File] menu, then retry the operation. W 5 If the same problem persists despite retrying, please call the Support Center. 110 1005 5010 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 26 Error Codes — Part Code 1005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level error occurs, call HP technical support. 1005 55206 The configuration information Check the settings, and then being set does not match the retry the operation. current configuration information. Check the settings, and then retry the operation. E 6 1005 55500 An error occurred during SVP If this problem persists, call processing.
Table 26 Error Codes — Part Code 1005 (continued) Part Code Error Number Error Message Recommended Action 1005 57101 An error occurred during SVP If this problem persists, call processing. HP technical support. Severity Level Failure Level E 2 E 2 If this problem persists, call HP technical support. 1005 57102 An error occurred during SVP If this problem persists, call processing. HP technical support. If this problem persists, call HP technical support.
Table 27 Error Codes — Part Code 1010 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level setting of the configuration information again. 1010 5010 The specified LDEVs and free Correct the specified content, W LUNs should be the same and retry. number. 5 1010 5040 The number of LU paths in You cannot specify any more. W use has already reached the maximum (2,048 in a Fibre Channel environment).
Table 27 Error Codes — Part Code 1010 (continued) 114 Part Code Error Number Error Message Recommended Action 1010 5822 You entered the wrong item. Correct the settings, and then W retry. 5 1010 5823 It is not updated. Correct the settings, and then W retry. 5 1010 5867 The specified volume cannot Release the reserved attribute W be manipulated because it is of the target volume by using reserved by RAID Manager. Data Retention Utility. 5 1010 6509 The host mode is invalid.
Table 27 Error Codes — Part Code 1010 (continued) Part Code Error Number Error Message Recommended Action 1010 55234 This action will cause a failover of resource groups on the node which is going to be shutdown if they are running. Are you sure to proceed? To continue processing, click W [OK]. To stop processing, click [Cancel]. 5 1010 59049 The setting extends across multiple SLPRs. Do you want to continue? To continue processing, click E [OK]. To stop processing, click [Cancel].
Table 28 Error Codes — Part Code 1110 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Specify the WWN with 16 characters, using any of the following combinations: • Numerals (0-9), • Letters (A-F), • Hyphen (-), or • Space. (You cannot specify 0 for all the 16 characters.) 116 1110 5001 The name should be input using specified letters (a-z and A-Y) and digits (0-9). Correct the specified content, W and retry.
Table 28 Error Codes — Part Code 1110 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 1110 5057 The WWN group already has the same LUN group. Check the content of the operation. W 5 1110 5058 The WWN already has the same LUN group. Check the content of the operation. W 5 1110 5060 The system cannot add WWN to LUN group. Check the content of the operation. W 5 1110 5061 The system cannot add WWN to WWN.
Table 28 Error Codes — Part Code 1110 (continued) Part Code Error Number Error Message 1110 9061 1110 Recommended Action Severity Level Failure Level The specified host will be deleted. Do you want to continue? i 0 9063 Warning: The LU path to the LDEV will be released at once.
Table 28 Error Codes — Part Code 1110 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level If the type of the Target name is iqn, specify the name within 223 characters. The characters can be any combinations of the following: • numerals (0-9) • letters from A to Z, a to z • dots (.) • hyphens (-) • colons (:) 1110 55546 The specified Target alias is incorrect. Correct the settings, and then W retry the operation.
Table 29 Error Codes — Part Code 1205 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level E 3 computer. If necessary, Call HP technical support. 1205 8966 An error occurred on the DKC side. If this problem persists, call HP technical support. An error occurred on the DKC side. If this problem persists, call HP technical support. 1205 56298 The SVP is busy. Wait for a while, and then retry the operation.
Table 30 Error Codes — Part Code 1305 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 1305 5013 An error occurred during SVP processing. If this problem persists, call HP technical support. An error occurred during SVP E processing. If this problem persists, call HP technical support. 2 1305 5099 An error occurred during SVP processing. If this problem persists, call HP technical support. An error occurred during SVP E processing.
Table 31 Error Codes — Part Code 1310 (continued) 122 Part Code Error Number Error Message Recommended Action Severity Level 1310 5833 The secret is incorrect. Correct the settings, and then W retry the operation. 5 1310 5834 The reentered secret does not Correct the settings, and then W match the previously entered retry the operation. secret. 5 1310 5835 The same user name is already registered. Correct the settings, and then W retry the operation.
Table 31 Error Codes — Part Code 1310 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level authentication information creation tool. 1310 69052 An error occurred in the client An error occurred in the client E processing. processing. See the message displayed in the console for Refer to the message displayed in the console for details. details.
Table 32 Error Codes — Part Code 2005 (continued) Part Code Error Number Error Message Recommended Action Severity Level 2005 1012 LU path is set to a volume which links as an expanded LU. The configuration information E has been already changed. Failure Level 6 Check the settings, and request the setting of the configuration information again. 2005 1013 The emulation types of the volumes combined into a LUSE volume are not the same.
Table 32 Error Codes — Part Code 2005 (continued) Part Code Error Number Error Message 2005 1182 The capacity of LUSE volume Check the setting. exceeds the maximum. 2005 1185 2005 1187 Recommended Action Severity Level Failure Level E 2 You are trying to insert in the linkage operation including LUSE. (LDEV number is inserted to the LDEV numbers created in LUSE). The configuration information E has been already changed.
Table 32 Error Codes — Part Code 2005 (continued) 126 Part Code Error Number Error Message 2005 1923 2005 Recommended Action Severity Level Failure Level The LDEVs to be combined Check the setting. are not specified, or the number of LDEVs exceeds the maximum number that can be combined. E 6 1924 The all volumes that compose Check the setting. the LUSE volume are not selected. E 6 2005 1925 The combination order of LUSE volume is incorrect.
Table 32 Error Codes — Part Code 2005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 2005 2099 The operation cannot be performed, because an inoperative MP exists. Wait a few seconds, and E then retry the operation. If the same problem persists, call HP technical support. 6 2005 2502 The specified volume cannot be combined as a LUSE volume because it does not Read/Write attribute (S-VOL enabled). Correct settings, and then retry.
Table 32 Error Codes — Part Code 2005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level the XP Provisioning volumes with the same pool first. 2005 65789 The LUSE operation cannot be performed, because the specified volume is being used as a quorum disk. Check the setting. E 6 2005 66004 The description of the operation tag is invalid. Check the contents of the spreadsheet.
Table 33 Error Codes — Part Code 2010 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 2010 5056 The specified LDEV is inaccurate. Follow the correct operation procedure. W 5 2010 5812 Are you sure you want to perform the LUSE operation on a volume that has a path definition? Click [OK] to continue the operation. Click [Cancel] to stop the operation. W 5 2010 5815 There are no LUSE volumes that can be reset. Check the specified volumes.
Table 33 Error Codes — Part Code 2010 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 2010 55034 You are trying to combine To continue processing, click W volumes having different SLPR [OK]. To stop processing, numbers into a LUSE volume. click [Cancel]. If you perform this operation, the storage partition administrator will become unable to operate.
Table 34 Error Codes — Part Code 3005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3005 2088 The XP Continuous Access pair is suspended. Add an alternative path. Add an alternative path. W 6 3005 2089 The corresponding CHA might contain the last path between the MCU and RCU of XP Continuous Access. Make sure that there is an alternative path from the MCU. Make sure that there is an alternative path from the MCU.
Table 34 Error Codes — Part Code 3005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level • Replacement of an OEM drive microprogram is in progress • LDEV shredding is in progress Therefore the specified operation cannot be executed. 132 3005 2200 The Concurrent Copy or the Compatible XRC operation is in progress in the target volumes. Cancel the Concurrent Copy job or delete a Compatible XRC pair via the host.
Table 34 Error Codes — Part Code 3005 (continued) Part Code Error Number Error Message Recommended Action Severity Level 3005 2515 One of the following is defined: a XP Continuous Access pair, a XP Continuous Access Journal pair, or a Universal Replicator for Mainframe pair. Release the pair definition or E delete command devices defined by Business Continuity Manager, and then retry the operation. Failure Level 6 Alternatively, command devices defined by Business Continuity Manager are included.
Table 34 Error Codes — Part Code 3005 (continued) 134 Part Code Error Number Error Message Recommended Action 3005 2521 An Auto LUN pair is defined. Please delete the pair definition. If a reserve volume is defined, please cancel the reservation and then retry the operation. Release the pair definition. If E a reserve volume is defined, cancel the reservation and then retry the operation. 3005 2522 The volume is reserved by Cancel the reservation, and Auto LUN.
Table 34 Error Codes — Part Code 3005 (continued) Part Code Error Number Error Message 3005 6024 3005 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 6036 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 34 Error Codes — Part Code 3005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level [Refresh All] on the File menu [Refresh All] on the File menu and refresh the configuration. and refresh the configuration. 3505 8979 The operation of the external volume has been failed because all the paths to the external volume are blocked. Restore more than one path E to the external volume, and then perform the operation of the external volume.
Table 34 Error Codes — Part Code 3005 (continued) Part Code Error Number Error Message 3005 55516 3005 55517 Recommended Action Severity Level Failure Level This function is not available, Install the program product. because the program product is not installed. E 6 An error occurred during SVP If this problem persists, call processing. HP technical support. E 2 E 2 If this problem persists, call HP technical support.
Table 34 Error Codes — Part Code 3005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level If this problem persists, call HP technical support. 138 3005 58460 The logical volume cannot be Install the logical volume. registered, because it is not installed. E 6 3005 58461 The specified operation Restore the blockade status cannot be done, because the of the logical volume. logical volume is blocked.
Table 34 Error Codes — Part Code 3005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3005 58472 Acquisition of the pool information has failed. When the pool information cannot be acquired, do the following: E 6 Pool information cannot be acquired when: • V-VOL management area is not initialized. • V-VOL management area is not installed.
Table 34 Error Codes — Part Code 3005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level and the SVP microcode version are mismatched. 3005 58574 An error occurred while If this problem persists, call connecting to the subsystem. HP technical support. Wait for a while, and then retry the operation. E 6 3005 58575 An error occurred while If this problem persists, call connecting to the subsystem. HP technical support.
Table 34 Error Codes — Part Code 3005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3005 65677 The association cannot be Release the paths, and then released because paths are retry the operation. defined to the target volumes. E 6 3005 65678 The association cannot be Release the LUSE setting, and E released because a LUSE then retry the operation. setting is made on the target volumes.
Table 34 Error Codes — Part Code 3005 (continued) 142 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3005 65695 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 3005 65717 The specified volumes contain Select only the volumes that E volumes that cannot be can be formatted and format formatted. Select only the the volumes.
Table 34 Error Codes — Part Code 3005 (continued) Part Code Error Number Error Message 3005 68748 3005 68751 Recommended Action Severity Level Failure Level The number of XP Thin Check the current Provisioning volumes that can configuration of association. be associated with a single pool has exceeded the maximum. E 6 The disk storage system is executing the processing to release the association, inside. Wait for a while, and then retry the operation.
Table 34 Error Codes — Part Code 3005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level E 6 • the threshold is set below the usage rate of the pool. • Update the display content and confirm the usage rate of the pool. Wait for the operation to be E completed, and then retry the operation. 6 window, and then retry the operation.
Table 34 Error Codes — Part Code 3005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3005 68824 The specified volume is currently used by XP Continuous Access or XP External Storage Access Manager. Wait until the process of XP Continuous Access or XP External Storage Access Manager is completed, and then retry the operation.
Table 35 Error Codes — Part Code 3010 Part Code Error Number Error Message Recommended Action 3010 1046 The number of Cache Residency Manager settings has exceeded the maximum number of available Cache Residency Manager areas. Reduce the number of Cache W Residency Manager settings, and then retry the operation. 5 3010 5010 The specified SSID falls out of range. Specify a valid SSID, and then retry the operation. Correct the specified content, W and retry.
Table 35 Error Codes — Part Code 3010 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Check the content of the operation. W 5 • release the JNL settings from the volume. • release the quorum disk settings from the volume. 3010 5055 There is no volume to be initialized.
Table 35 Error Codes — Part Code 3010 (continued) Part Code Error Number Error Message Recommended Action 3010 5065 The number of LDEVs is not specified. Specify the number of LDEVs W correctly. 3010 5066 The specified size or number Check the content of the is invalid. operation. E 5 3010 5870 No write data is entered in the [Define] text box. Check the content of the operation. E 5 3010 5871 The number of entered Check the content of the characters is odd. Enter even operation.
Table 35 Error Codes — Part Code 3010 (continued) Part Code Error Number Error Message 3010 9150 Specify the SSID. 3010 Recommended Action Severity Level Failure Level i 0 9370 The specified volume will be To continue processing, click i shredded. Are you sure you OK. To stop processing, click want to continue? (If the top Cancel. LDEV of the LUSE volume is selected, all the LDEVs that make up the LUSE volume will be shredded.) 5 3010 9371 Shredding has completed.
Table 35 Error Codes — Part Code 3010 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level W 0 You can only set another %s LDEVs because the number of LDEVs that can be set in a VDEV is more than the number of LDEVs that can be set by Install CV setting one time. 3010 55635 The format processing, the Click [OK]. shredding processing, and the prepare for Quick Format are not executed.
Table 35 Error Codes — Part Code 3010 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3010 59333 The specified item will be canceled. Do you want to continue? To cancel the specified item and acquire progress, click [OK]. Otherwise, click [Cancel]. W 5 3010 59334 The format processing completed. Click [OK]. i 5 3010 65640 Set one or more volumes. Set one or more volumes.
Table 35 Error Codes — Part Code 3010 (continued) Part Code Error Number Error Message Recommended Action 3010 69029 If the unit of display is To continue processing, click W changed, the status of the [OK]. To stop processing, setting will return to the status click [Cancel]. set before. Do you want to continue? 5 3010 69030 The information that is under To continue processing, click W setup is not applied to the [OK]. To stop processing, device yet. The information click [Cancel].
Table 36 Error Codes — Part Code 3110 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3110 55501 Pool-VOLs are not registered to the newly created pool. Check the specified content, and retry the operation. W 5 3110 55502 The Pool ID setting is incorrect. Check the specified content, and retry the operation. W 5 3110 55503 The specified Pool ID already Check the specified content, exists. and retry the operation.
Table 37 Error Codes — Part Code 3205 Part Code Error Number Error Message Recommended Action 3205 2011 The status of the storage system requires the maintenance (for example, the subsystem is blocked, the shared memory is inconsistent, or some other factor). Call HP technical support. Check the status of the disk E storage system (if the storage system is blocked, inconsistency of shared memory, or some other factor). If this problem persists, call HP technical support.
Table 37 Error Codes — Part Code 3205 (continued) Part Code Error Number Error Message Recommended Action Severity Level 3205 2200 The Concurrent Copy or the If the Concurrent Copy or the W Compatible XRC operation is Compatible XRC operation: in progress in the target • Is in progress in the target volumes. Cancel the volumes, cancel the Concurrent Copy job or Concurrent Copy job or delete a Compatible XRC delete a Compatible XRC pair via the host. pair via the host.
Table 37 Error Codes — Part Code 3205 (continued) Part Code 156 Error Number Error Message Recommended Action subsystem exceeds the maximum. the storage system, and retry the operation. Severity Level Failure Level 3205 6535 You cannot make changes Release the logical path, and E because a logical path to the then change the volume still remains. configuration. 5 3205 6537 There is no error in this setting.
Table 37 Error Codes — Part Code 3205 (continued) Part Code Error Number Error Message Recommended Action persists, call HP technical support. persists, call HP technical support. Severity Level Failure Level 3205 8957 An error occurred on the DKC side. If this problem persists, call HP technical support. An error occurred on the DKC side. If this problem persists, call HP technical support. E 3 3205 8958 An error occurred on the DKC side. If this problem persists, call HP technical support.
Table 37 Error Codes — Part Code 3205 (continued) Part Code 158 Error Number Error Message Recommended Action persists, call HP technical support. persists, call HP technical support. Severity Level Failure Level 3205 8969 An error occurred on the DKC side. If this problem persists, call HP technical support. An error occurred on the DKC side. If this problem persists, call HP technical support. E 3 3205 8970 An error occurred on the DKC side.
Table 37 Error Codes — Part Code 3205 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3205 67764 The number of XP Thin Check the setting. Provisioning volumes (TP-VOL) that can be defined in one V-VOL group is just one. E 5 3205 68735 A volume used as System Disk is included in the items to be maintained. Restore the blockage status E of the system disk. If the status cannot be restored, call HP technical support.
Table 38 Error Codes — Part Code 3210 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3210 55001 The specified V-VOL group cannot be deleted. Check the specified content, and retry the operation. W 5 A V-VOL group cannot be deleted when it contains the following volumes: • A volume with path definition. • A LUSE volume. 3210 55002 The maximum number of V-VOL Groups is already registered. Check the setting range, and W then retry the operation.
Table 38 Error Codes — Part Code 3210 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3210 59001 Are you sure you want to delete the selected V-VOL group? To continue processing, click i [OK]. Otherwise, click [Cancel]. 5 3210 59201 The V-VOL group information To continue processing, click i is to be set with free setting. [OK]. Otherwise, click [Cancel].
Table 38 Error Codes — Part Code 3210 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3210 65754 The same operation cannot be done, because the discarding zero data is currently being executed. Check the content of the operation. W 5 3210 65755 Cancel operation of the Check the content of the discarding zero data cannot operation. be performed because the system is not executing the zero data discarding. W 5 3210 65766 Set volumes.
Table 38 Error Codes — Part Code 3210 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level OPEN-0V will change to OPEN-V. Execute the operation by selecting the following modes. (The temporary setting will be discarded.) [Normal] executes the operation only to the TP-VOLs where paths are not set. [Force] executes the operation to all TP-VOLs. Confirm that the operation does not affect the host before executing the operation.
Table 39 Error Codes — Part Code 3305 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level then change the size of volume. 3305 1037 The free space remaining in There is no capacity left in E the parity group is not the logical parity group to enough to install a create CV. The error does not customized volume (CV). occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact HP technical support.
Table 39 Error Codes — Part Code 3305 (continued) Part Code Error Number Error Message Recommended Action last LDEV of RAID striping group. you cannot uninstall anymore. Severity Level Failure Level 3305 1103 An operation is specified for Correct the settings, and then E the uninstalled Parity Group. retry the operation. 2 3305 1104 Subsystem ID cannot be set alone. Request the change of the Subsystem ID along with the VLL operation.
Table 39 Error Codes — Part Code 3305 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level number of XP Thin Provisioning volume(s) that can be set in a disk subsystem. 3305 2004 An error occurred during SVP processing. If this problem persists, call HP technical support. If this problem persists, call HP technical support. E 2 3305 2005 An error occurred during SVP processing. If this problem persists, call HP technical support.
Table 39 Error Codes — Part Code 3305 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Add an alternative path. subsystem offline from the host. 3305 2088 The XP Continuous Access pair is suspended. Add an alternative path. W 6 3305 2089 The corresponding CHA Be sure there is an alternative W might contain the last path path from the MCU. between the MCU and RCU of XP Continuous Access. Make sure that there is an alternative path from the MCU.
Table 39 Error Codes — Part Code 3305 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level • Replacement of an OEM drive microprogram is in progress • LDEV shredding is in progress Therefore the specified operation cannot be executed. 3305 2200 The Concurrent Copy or the Compatible XRC operation is in progress in the target volumes. Cancel the Concurrent Copy job or delete a Compatible XRC pair via the host.
Table 39 Error Codes — Part Code 3305 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level suspend the pair, and then retry the operation. 3305 2517 One of the following is defined: a Business Copy pair, a ShadowImage for Mainframe pair, or a Compatible FlashCopy(R) pair. Split the pair, and then retry the operation. If the Quick Split mode is on, suspend the pair, and then split. Split the pair, and then retry E the operation.
Table 39 Error Codes — Part Code 3305 (continued) 170 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3305 3008 An error occurred during SVP processing. If this problem persists, call HP technical support. If this problem persists, call HP technical support. E 2 3305 5013 An error occurred during SVP processing. If this problem persists, call HP technical support. If this problem persists, call HP technical support.
Table 39 Error Codes — Part Code 3305 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3305 65661 There are no changes in the Check the setting. current configuration and the setting. E 6 3305 65669 The XP Thin Provisioning volume associated with a pool is included in the items to be maintained. Release the association of the XP Thin Provisioning volume and the pool to be maintained.
Table 39 Error Codes — Part Code 3305 (continued) Part Code 172 Error Number Error Message Recommended Action number of parity groups being quick formatted has exceeded the maximum. Execute the format processing for the added volume. To execute quick format processing, execute after the quick format processing for other parity groups has completed. be executed after the quick format processing for other parity groups has completed.
Table 39 Error Codes — Part Code 3305 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level device being used by a mirror of the journal group. 3305 66825 A parity group, to which 17 or more VDEVs are allocated, exists. Please contact the application E program distributor. 3 Wait for the operation to be E completed, and then retry the operation.
Table 40 Error Codes — Part Code 4005 (continued) Part Code Error Number Error Message 4005 5099 4005 Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, please call HP technical support. E 2 6001 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 40 Error Codes — Part Code 4005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Check the settings, and then retry the operation. E 6 SLPR No:%s 4005 55245 The number of Cache Residency areas set for the CLPR exceeds the maximum available number of Cache Residency areas.
Table 40 Error Codes — Part Code 4005 (continued) 176 Part Code Error Number Error Message 4005 55536 4005 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 55537 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 40 Error Codes — Part Code 4005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level the configuration operation. Or check the status of the disk storage system to find whether the storage system is blocked or not. If the problem persists, call HP technical support. 4005 58514 Currently running microcode version does not support the specified operation. Call HP technical support. E 2 4005 58709 A maintenance operation is in progress.
Table 41 Error Codes — Part Code 4010 (continued) Part Code Error Number Error Message Recommended Action Severity Level 4010 5011 The value specified as the Correct the specified content, W Number of Cache Residency and retry. areas is equal to or less than one cylinder. 5 4010 5030 No deletion area is specified. Correct the specified content, W Retry the operation to specify and retry. the deletion area.
Table 42 Error Codes — Part Code 4105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 4105 6510 The disk subsystem is busy. Please wait for a while, and then retry the operation. Wait a few seconds, and then retry the operation. W 5 4105 7060 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 42 Error Codes — Part Code 4105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 4105 57008 The maximum value of PCR capacity per the specified CLPR is not multiples of 512MB. Check the settings, and retry E the operation. 6 4105 57009 The capacity of PCR that each CLPR uses exceeds the maximum value of PCR capacity per CLPR. Check the settings, and retry E the operation.
Table 43 Error Codes — Part Code 5105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 5105 5400 Since the SVP is busy, the monitoring data cannot be obtained. Wait a few seconds, and then retry. W 3 Do either of the following if two users are displaying the Performance Monitor window or running the Export Tool: • Ask one of the users to display another window. • Ask one of the users to log off. • Wait for one of the users to quit the Export Tool.
Table 43 Error Codes — Part Code 5105 (continued) 182 Part Code Error Number Error Message 5105 7111 5105 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 7428 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 43 Error Codes — Part Code 5105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 5105 56526 The resources of other SLPR(s) Correct the settings, and then E cannot be accessed. retry the operation. 6 5105 66016 A monitoring switch cannot Change the gathering be enabled with the specified interval, and retry the gathering interval. operation. W 5 5105 66017 An error occurred during SVP If this problem persists, call processing.
Table 45 Error Codes — Part Code 5205 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 5205 1076 The reserve attribute cannot Specify another volume. be set to the specified volume, because it is already used as a volume of ShadowImage for Mainframe, XP Business Copy, or Compatible FlashCopy(R). E 6 5205 1077 The specified volume(s) are already used by XP Business Copy, ShadowImage for Mainframe, or Compatible FlashCopy(R).
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level already used as a reserved volume of ShadowImage for Mainframe, XP Business Copy, or XP Auto LUN. 5205 1094 The volume is not a reserved Retry the same operation. If volume. nothing changes, call HP technical support. E 6 5205 1095 The number of the reserved Retry the same operation.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 5205 1210 The shared memory to set a plan is insufficient. Install the shared memory if E it is possible. If it is impossible to install the shared memory, the plan cannot be set any further.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message 5205 1220 5205 Recommended Action Severity Level Failure Level The volume is not a reserved Retry the same operation. If volume. nothing changes, call HP technical support. E 6 1221 The volume(s) are already used by Auto LUN. Retry the same operation. If nothing changes, call HP technical support.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 5205 1231 The volume(s) is already being used by Data Migration. Release the Data Migration. E 6 5205 1232 The volume specified as a Specify another volume. migration target cannot be migrated, because it is already used as a volume of ShadowImage for Mainframe, XP Business Copy, or Compatible FlashCopy(R).
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Mainframe, or Compatible FlashCopy(R). 5205 1241 The volume specified as the migration source has the Cache Residency settings. The volume set by Cache Residency Manager cannot be used for XP Auto LUN. Specify another volume. E 6 5205 1242 The volume specified as the migration target has the Cache Residency settings.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 5205 2025 The controller detected the blockade location. Call HP technical support. E 6 5205 2026 The controller detected the blockade location. Call HP technical support. E 6 5205 2027 The controller detected the blockade location. Call HP technical support. E 6 5205 2028 The controller detected the blockade location. Call HP technical support.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message 5205 5505 The volume(s) is already Release the XP Continuous being used by XP Continuous Access Pair. Access. 5205 5506 The specified volume cannot be migrated, because it is used as a P-VOL in either of the following statuses. • A volume of XP Business Copy or TrueCopy for Mainframe in the state of pending.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message Recommended Action 5205 6502 Processing in progress. Please wait for a while, and then retry the operation. Retry the same operation W several times. If the same error occurs, call HP technical support. 0 5205 6510 The disk subsystem is busy. Please wait for a while, and then retry the operation. Retry the same operation W several times. If the same error occurs, call HP technical support.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message Recommended Action Severity Level exist in the specified directory. error occurs, call HP technical support. Failure Level 5205 7407 Cannot make proper migration plan for this function. Retry the same operation E several times. If the same error occurs, call HP technical support. 6 5205 7408 There is not enough valid monitoring data in the specified term. Retry the same operation E several times.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level error occurs, call HP technical support. 5205 7420 There is insufficient Auto LUN Retry the same operation E data to create migration several times. If the same plans. Check the following: error occurs, call HP technical support.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message Recommended Action Severity Level 5205 8529 An internal logic error occurred. Check the volume, or quit E using XP Continuous Access. 0 5205 8530 An internal logic error occurred. Check the volume, or quit E using XP Continuous Access. 0 5205 8531 An internal logic error occurred. Check the volume, or quit E using XP Continuous Access.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level not match the owner ID of the specified reserve volume. 196 5205 55225 The specified plan was not The specified plan cannot be E created with the Remote Web released with Remote Web Console. Console. 6 5205 55226 The specified plan was not The specified plan cannot be E created with the Remote Web released with Remote Web Console. Console.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 5205 55524 The specified volume(s) are already being used as XP Snapshot volume(s). Select another volume. E 6 5205 55525 The specified volume(s) are already being used as V-VOL(s). Select another volume. E 6 5205 55526 The specified volume(s) are already being used as Pool-VOL(s). Select another volume.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message 5205 55598 5205 Recommended Action Severity Level Failure Level The specified volume is used Check the setting of the as a Delta resync volume for specified volume. XP Continuous Access Journal or Universal Replicator for Mainframe. E 6 55599 The volume specified as a migration target is used as a volume of Delta resync for XP Continuous Access Journal or Universal Replicator for Mainframe.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level E 2 persists, call HP technical support. 5205 57102 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. 5205 58451 The storage system is in internal process. Retry the operation. If the problem persists despite W retrying, call HP technical support.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 5205 65700 The volume specified as a migration source cannot be used, because it is being used by FICON(R) Data Migration. Specify another volume. E 6 5205 65701 The volume specified as a migration source cannot be used, because it is being used by FICON(R) Data Migration. Specify another volume.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level configuration is being backed up in the volume. Wait for a while, and then retry the operation. 5205 65715 Migration cannot be Check the setting of the executed because it is a specified volume. migration between an XP Thin Provisioning volume and a normal volume that contains a component of a LUSE volume.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level used, because it is a quorum disk. 5205 65785 The volume specified as a Check the content of the migration target cannot be operation. used, because it is a quorum disk. E 6 5205 65786 The volume specified as the Check the content of the reserved volume cannot be operation. used, because it is a quorum disk.
Table 46 Error Codes — Part Code 5210 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 5210 66800 This migration plan cannot Restore the pool associated be executed, because the with the target volume, and pool associated to the target then retry the operation. volume is blocked. W 5 5210 66801 This migration plan cannot be executed because the usage rate of the pool associated to the target volume may be 100 percent or more.
Table 47 Error Codes — Part Code 5305 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 5305 5010 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 5305 5013 An error occurred during SVP Retry the same operation. If E processing. If this problem the same error occurs, call HP persists, call HP technical technical support. support.
Table 47 Error Codes — Part Code 5305 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 5305 5204 This functionality is not available because Performance Control is not installed. Install the required program product. W 6 5305 6000 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 47 Error Codes — Part Code 5305 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level persists, call HP technical support. 5305 55500 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 5305 56301 An error occurred during SVP The error may be caused by processing. a temporary communication failure.
Table 47 Error Codes — Part Code 5305 (continued) Part Code Error Number Error Message Recommended Action If this problem persists, call HP technical support. failure. Reboot the SVP or click [Refresh All] on the File menu of Remote Web Console and refresh the configuration information to recover from the error. Severity Level Failure Level E 2 E 6 If this problem persists, call HP technical support. 5305 57102 An error occurred during SVP The error may be caused by processing.
Table 47 Error Codes — Part Code 5305 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level system. Wait for a while, and click [Refresh All] on the File then retry the operation. menu of Remote Web Console and refresh the configuration information to recover from the error. If this problem persists, call HP technical support.
Table 49 Error Codes — Part Code 5310 (continued) Part Code Error Number Error Message 5310 5107 5310 Recommended Action Severity Level Failure Level The specified name is already Check the specified content, used. and retry. i 5 5108 The specified name is already Check the specified content, used. and retry. i 5 5310 5109 The number of WWN(s) that Check the specified content, is monitored exceeds the and retry. maximum in the port.
Table 49 Error Codes — Part Code 5310 (continued) 210 Part Code Error Number Error Message Recommended Action 5310 9312 The control status will change The control status will change W to Port Control. to Port Control. Click [OK]. 5 5310 9313 The control status will change The control status will change W to WWN Control. to WWN Control. Click [OK]. 5 5310 9314 There is no control, because the upper value is 0 in all ports.
Table 49 Error Codes — Part Code 5310 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Severity Level Failure Level port has reached the target at the same time, and maximum for the ports being then retry the operation. set as monitoring target at the same time. Table 50 Error Codes — Part Code 6005 Part Code Error Number Error Message Recommended Action 6005 5013 An error occurred during SVP If this problem persists, call processing.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level If the pair status is not and the condition of the paths changed after refreshing the between the MCU and RCU. window, check the MCU or RCU and the condition of the paths between the MCU and RCU. 212 6005 8700 Retry operation. Retry the operation. i 4 6005 8701 Logical Path between the MCU and the RCU is not active.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level i 4 the pair status, and if the operation is permitted retry. 6005 8711 The Port, GID, LUN, CU, or Check if the specified Port, LDEV number of the specified GID, LUN, CU, or LDEV volume is incorrect. number exists in the storage system. 6005 8712 The operation was rejected due to a FREEZE state. 1.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level RCU, and then retry the operation. 214 6005 8722 Failure during path creation. Check the path connections between the MCU and the RCU, and then retry the operation. E 4 6005 8723 The Edit Path operation was Add another path, or delete rejected because the all pairs on the RCU. Then specified path is the last path retry the operation.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6005 8733 The Fibre-XP Continuous Access function is not installed in the specified MCU. Install the program product key in the MCU. i 4 6005 8734 The Fibre-XP Continuous Install the program product Access function is not key in the RCU. installed in the specified RCU. i 4 6005 8735 Invalid RCU serial number, SSID, Link Address or Controller ID.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level i 4 • The volume is copying data (correction copy or drive copy). • The volume is correction access condition. Check the logical device status of the specified M-VOL. If the M-VOL is either under maintenance or copying data, retry the operation after the process is completed. 6005 8745 A volume cannot be used as Select another volume.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Controller emulation type, or 1. Confirm the controller the CT Group is not usable. emulation type, and see the manual. 2. Confirm the CT Group number in the MCU. 6005 8753 An internal error occurred. Call HP technical support. E 4 6005 8754 Invalid MCU serial number or MCU SSID. Check the serial number or E SSID of MCU, and then retry with correct parameter.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level it is off, set it on and retry. If it cannot be set on, call HP technical support. 218 6005 8763 R-VOL DFW status is not active. Check the DFW status of the i R-VOL from the host. If it is off, set it on and retry. If it cannot be set on, call HP technical support. 4 6005 8764 The specified R-VOL is not usable. Confirm the status of the specified R-VOL.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6005 8775 Multi platform feature already The multi-platform feature has i installed in RCU. already been installed in the RCU. Verify the configuration of the RCU. 4 6005 8776 A volume cannot be used as Select another volume. an M-VOL when: i 4 • it is used by XP Continuous Access Journal or Universal Replicator for Mainframe.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6005 8790 The specified expansion volume (Port/GID/LUN) of the RCU is not usable. Confirm the status of the i specified expansion volume and microcode version of the RCU. 4 6005 8791 The specified M-VOL is still online from another HOST. Vary the concerned path i offline from the other host, and then retry the operation.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Check the status of the specified M-VOL from the host or the SVP. Mainframe or Business Copy. • A volume of ShadowImage for Mainframe or Business Copy in Reverse Copy status. • A volume of FICON(R) Data Migration. 6005 8797 If the M-VOL is the ShadowImage for Mainframe/Business Copy/Compatible FlashCopy(R) T-VOL, one S-VOL must be paired with one T-VOL.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6005 8805 CT Group is not active in the The resume pair operation i RCU. failed, because there is no R-VOL in the CT Group. Verify the status of the CT group in the MCU/RCU. If an M-VOL exists, delete it and retry the add pair operation. 4 6005 8806 CT Group Option cannot be changed unless deleting or suspending all asynchronous pairs in the group.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Asynchronous pairs, or XP Continuous Access Journal Continuous Access Journal window of the MCU and pairs cannot be combined in RCU. one CT Group. 6005 8817 Preset Suspension is effective Cancel the preset suspension i in the CT Group. in the CT group, and then retry the operation.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message 6005 8825 6005 6005 Recommended Action Severity Level Failure Level The Add Pair Refresh and confirm the XP (Paircreate)/Resume Pair Continuous Access window (Pairresync) operation failed in the MCU and RCU. combining pairs (using Fibre path and Serial path) is not allowed in the same CT Group. i 4 8826 An internal error occurred. Call HP technical support.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6005 8836 No additional volume pairs waiting for copy. Check the pair status and retry. i 4 6005 8837 An internal error occurred. Call HP technical support. E 4 6005 8838 Specified volume is not part of a XP Continuous Access pair. The specified volume is not part of a XP Continuous Access pair. Check the volume.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6005 8846 An internal error occurred. Call HP technical support. E 4 6005 8847 An internal error occurred. Call HP technical support. E 4 6005 8848 Wait a few minutes and retry The suspend pair (Pairsplit-r) the Suspend Pair (Pairsplit-r) operation failed. A few operation.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6005 8857 Some volumes were not deleted by the Delete Pair (Pairsplit-S) operation. The operation failed for one i or more of the volumes, because either the pair status of the volume is SEQCHK or the consistency time of the volume does not match the consistency time of the CT group. Verify the status of the failed volumes.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6005 8869 CT Group is not active. Verify that the CT group is active in the MCU. E 4 6005 8870 CT Group Option cannot be changed unless all asynchronous pairs in the group are suspended or deleted. The group operation failed i because the specified group has at least one asynchronous pair. Refresh and check the XP Continuous Access window.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6005 8889 The specified port is not equipped. Refresh the window, and E retry. If nothing changes, call HP technical support. 4 6005 8890 The specified port is being initialized. Wait until the initialization of E the port ends, and retry the operation. 4 6005 8891 Logical paths exist on the MCU port.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level the maximum that can be created by the system. 6005 8905 The extended SM is not equipped in MCU. Install the shared memory to E the MCU with the installation instruction of expansion SM for remote copy (Shared Memory Size Configuration). 6005 8906 No more space is left in RCU If the extended shared for differential management.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6005 8914 Multi platform feature already The multi-platform feature has i installed in subsystem. already been installed in the storage system. Verify the configuration of the storage system. 4 6005 8915 The port type exchange operation is rejected because the host(s) is (are) processing the port type exchange.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level LDKC number or CU number is defined as configuration does not exist, the logical information for the MCU. paths between MCU and RCU cannot be established. 6005 8934 The Paircreate operation failed because specified R-VOL is the NAS system volume. Check the configuration of the specified R-VOL.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message 6005 8945 At least one of the following is invalid: Recommended Action Severity Level Verify whether the W parameters of M-VOL, for example, CU number, port, • M-VOL parameters (CU number, Port, GID, LUN) GID and LUN, are supported with the RCU microcode • SSID or CU number of the program version or not.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level CT groups of asynchronous pairs that you can register in SLPR exceeds the limit. 6005 8985 The coexistence of volumes Check the settings, and then that are in the different CLPRs retry the operation. is not allowed within one CT group.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message 6005 57005 6005 6005 Recommended Action Severity Level Failure Level An error occurred during SVP Call HP technical support. processing. If this problem persists, call HP technical support. E 3 58319 A pair cannot be created Select another volume, and because the specified M-VOL retry the operation. is used by XP Continuous Access Journal or Universal Replicator for Mainframe.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action 6005 58359 A pair cannot be created, Wait a few seconds, and because the set processing of then retry the operation. VMA that is used for Data Retention Utility has not been completed for the specified S-VOL. 6005 58451 The storage system is in internal process. Retry the operation. If the problem persists despite W retrying, call HP technical support.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message 6005 58496 6005 Recommended Action Severity Level Failure Level A pair cannot be created Specify another volume. because the specified M-VOL is a virtual volume. i 5 58497 A pair cannot be created because the specified R-VOL is a virtual volume. Specify another volume. i 5 6005 58498 A pair cannot be created Specify another volume. because the specified M-VOL is being used as a pool volume.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Check the licensed capacity TrueCopy for Mainframe for of this program product and details on the licensed the related program products. capacities.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level The related program products The related program products are: are: • XP Continuous Access or TrueCopy for Mainframe • XP Continuous Access or TrueCopy for Mainframe • XP Continuous Access Asynchronous or TrueCopy Asynchronous for Mainframe • XP Continuous Access Asynchronous or TrueCopy Asynchronous for Mainframe 6005 68011 The operation failed because Check whe
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message 6005 68764 6005 Recommended Action Severity Level Failure Level The Add Pair (Paircreate) Check whether the specified operation failed because the M-VOL is a System Disk. specified M-VOL is a System Disk. W 0 68787 The operation failed because Install XP Continuous Access the XP Continuous Access to the storage system. function was not installed.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level volume whose capacity was being changed. combination of volumes for pair creating. Failure Level 6005 68816 A pair cannot be created because the specified volume is used as a primary data volume of the XP Continuous Access Journal.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action was used for XP External Storage Access Manager. quorum disk ID, and then retry the operation. Severity Level Failure Level 6005 68844 The operation failed, because the specified M-VOL was a volume of XP Thin Provisioning whose zero data was being discarded. Retry the operation after the completion of discarding zero data on the specified volume.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message 6005 68880 6005 6005 Recommended Action Severity Level Failure Level The operation failed, because Select another volume, or the specified volume was release the XP Auto LUN used for Auto LUN. setting. E 5 68881 The operation failed, because Select another volume. the specified volume was used as a system disk.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level pair of XP External Storage Access Manager. 6005 68899 The operation failed, because Confirm the quorum disk ID a quorum disk was not status. registered in the specified quorum disk ID. W 0 6005 68900 The operation failed, because Confirm the quorum disk ID the specified quorum disk ID for the specified pair.
Table 52 Error Codes — Part Code 6010 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6010 5010 The Priority value is invalid. Specify the correct value. Correct the specified contents, and retry. W 5 6010 5011 The Range value is invalid. Specify the correct value. Correct the specified contents, and retry. W 5 6010 5012 The Error Level value is invalid. Specify the correct value. Correct the specified contents, and retry.
Table 52 Error Codes — Part Code 6010 (continued) Part Code Error Number Error Message 6010 5140 6010 Recommended Action Severity Level Failure Level The specified CU number is Specify the correct CU incorrect. Specify the correct number. CU number. W 0 5141 The specified LDEV number is incorrect. Specify the correct LDEV number. Specify the correct device number. W 0 6010 5142 The specified GID is Specify the correct group incorrect. Specify the correct number. GID.
Table 52 Error Codes — Part Code 6010 (continued) Part Code Error Number Error Message Recommended Action some volume pairs. Are you sure that the M-VOL and the R-VOL of these pairs are already synchronized? the contents match, click [OK]. If not, click [Cancel]. Severity Level Failure Level 6010 9024 Are you sure you want to Follow the instructions in the exchange the specified ports? message. Confirm the associated channel paths are off-line.
Table 52 Error Codes — Part Code 6010 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6010 9104 Do you want to change the mode? To switch the mode, click [OK]. If not, click [Cancel]. i 0 6010 9105 The value that is under setup To close the window, click is not reflected yet. Do you [OK]. To not close the want to exit? window, click [Cancel]. i 0 6010 9106 The value that is under setup To change the mode, click is not reflected yet.
Table 52 Error Codes — Part Code 6010 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level want to continue this operation? 6010 9122 Are you sure you want to export pair status? To output pair status into a snapshot file, click [OK]. To cancel this operation, click [Cancel]. i 0 6010 9124 This process may take up to %d minutes. Do you want to continue? To continue the operation, click [OK]. To cancel the operation, click [Cancel].
Table 52 Error Codes — Part Code 6010 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6010 9303 There are no valid volumes. Confirm whether the W command device for Business Continuity Manager is defined. 6010 9304 WARNING: Group or C/T Follow the instructions in the is specified for Delete Range. message. Confirm all pairs in the group are synchronized.
Table 52 Error Codes — Part Code 6010 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6010 9318 As a result of this operation, To delete the pair, even W you will not be able to re-start though you cannot re-execute ERASE R-VOL operation. the R-VOL deletion, click [OK]. If not, click [Cancel]. 0 6010 9324 The specified operation is prohibited while the script is running. Try again after the script ends. W 0 6010 9325 The script is terminated forcibly.
Table 52 Error Codes — Part Code 6010 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6010 59011 Are you sure you want to output the %s file? To output the file, click [Yes]. Otherwise, click [No]. i 0 6010 59012 The %s file does not exist. Click [OK]. i 0 6010 59013 The specified file already exists. Do you want to overwrite this file? To overwrite the file, click [Yes]. Otherwise, click [No].
Table 52 Error Codes — Part Code 6010 (continued) Part Code Error Number Error Message Recommended Action 6010 65769 There are no quorum disk IDs Register some quorum disk available. IDs, and then retry the operation. Register some quorum disk Severity Level Failure Level W 0 IDs, and then retry the operation. 6010 65770 There are no RCUs available. Register some RCUs of CU Register some RCUs of CU Free, and then retry the Free, and then retry the operation. operation.
Table 52 Error Codes — Part Code 6010 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6010 69023 There are no RCUs available. To create pairs that have W different CU numbers To create pairs that have coexisting in the pair, register different CU numbers coexisting in the pair, register RCU of CU Free and retry the RCU of CU Free and retry the operation. Failure Level 0 operation.
Table 52 Error Codes — Part Code 6010 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6010 69076 Are you sure you want to delete the quorum disk ID? To delete the quorum disk ID, i click [OK]. Otherwise, click [Cancel]. 6010 69085 [Warning] To perform the operation, If you perform this operation, click OK. Otherwise, click there are some pairs that will Cancel. change the pair mode from "Sync" to "ESAM".
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action 6505 6022 A file open error has occurred. If the problem persists despite E retrying, call HP technical support. 2 6505 6023 An error occurred during SVP If the problem persists despite E processing. If this problem retrying, call HP technical persists, call HP technical support. support. 2 6505 6502 Processing in progress. Please wait for a while, and then retry the operation.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level operation on the primary data volume. 6505 8703 The specified number of Check the number of paths. paths is less than the minimum number of paths in the DKC Option window. i 4 6505 8704 The specified number of Check the path status in the paths is less than the DKC Status window, and minimum number of paths in then restore the paths.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 8719 The serial number or the controller ID of the remote subsystem is incorrect. Check the serial number and E the controller ID of this remote storage system and already registered remote storage systems, and then specify the correct values. Failure Level 4 If the specified values are correct, check the cable connection of the remote storage system.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level minimum number of paths, and then delete paths. 6505 8729 An internal error occurred. Check the SSB log, and then E call HP technical support. 6505 8730 The specified logical address Do either of the following to is incorrect. recover from the error: 4 i 4 i 4 • If you are adding DKCs, specify the same logical address.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action groups or data volume pairs for remote copy operations. groups, if any. Ensure that there are no data volume pairs and journal groups, and then retry the operation. Severity Level Failure Level 6505 8737 An internal error occurred. Check the SSB log, and then E call HP technical support. 4 6505 8742 Pinned track(s) exists in the primary data volume.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 8746 The emulation type of the primary data volume is not supported by XP Continuous Access Journal or Universal Replicator for Mainframe. See the Installation and Open i Platform sections in the maintenance manual to check if the device emulation of the primary data volume is supported.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 8791 The specified primary data volume is online from hosts. Vary the path offline from the i other host, and then retry the operation. 4 6505 8795 The operation failed because Check the status of the i the specified primary data primary data volume from the volume was used by Business host or the SVP.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level • a Business Copy P-VOL in Swap or Reverse Copy status • a ShadowImage for Mainframe S-VOL in Swap or Reverse Copy status 6505 8822 An I/O error occurred on the Check the SSB log, and then E secondary data volume. call HP technical support. 4 6505 8830 The specified primary data volume is already reserved by Auto LUN.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action 6505 8893 An internal error occurred. Check the SSB log, and then E call HP technical support. 4 6505 8894 Jobs exist on the port. Stop the jobs from the host and retry the operation. E 4 6505 8895 Jobs exist on the port on the remote subsystem. Stop the jobs from the host and retry the operation. E 4 6505 8896 Parameter error has occurred. Refresh the window, and E retry.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 8932 Failed to create the logical path, because the configuration definition of the specified LDKC number did not exist in the primary storage system. Check whether the specified LDKC number is defined in the configuration of the primary storage system.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 58005 Too many requests. Reduce the number of requests to be processed at one time. After that, retry the operation. Reduce the number of requests to be processed at one time. Then retry the operation. i 0 6505 58006 Invalid parameter (LDEV number). Check the specified LDEV number. i 0 6505 58007 Invalid parameter (journal group number).
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message 6505 58022 6505 Recommended Action Severity Level Failure Level A Concurrent Copy operation Check the status of the is in progress on the specified specified volume. volume. i 0 58023 The specified CLPR number is Check the specified CLPR incorrect. number. i 0 6505 58024 The specified cache value for Check the specified cache master journal groups is value for master journal invalid. groups.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action 6505 58035 No more journal volumes can Check the number of the i be registered, or too many journal volumes in the volumes are selected. specified journal groups. Also, check the number of the selected volumes. 0 6505 58036 The device emulation type of Check the emulation type of the specified volume is not the specified volume. supported.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message 6505 58073 6505 Recommended Action Severity Level Failure Level The subsystem is busy. Wait If the error occurs after for a while, and then retry the retrying, call HP technical operation. support. W 0 58075 The specified serial number is incorrect. Check the specified serial number. i 0 6505 58078 The specified volume does not exist or is unusable. Check the status of the specified volume.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action 6505 58087 The emulation type of the Check the emulation type of specified primary data the specified primary data volume is incorrect due to volume. one of the following reasons: Severity Level Failure Level i 0 • The emulation type is not supported. • The combination of emulation types within the journal group is incorrect.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 58099 The cache or the shared memory is in an abnormal state. Call HP technical support. i 0 6505 58100 The serial number or the controller ID of the remote subsystem is incorrect. Check the serial number and i the controller ID of this remote storage system and already registered remote storage systems, and then specify the correct values.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 58106 The operation failed because the specified data volumes were in one of the following statuses: Verify the following items for W the specified primary data volume and secondary data volume. Failure Level 4 • The capacities of primary • If the capacities of primary and secondary data and secondary data volumes do not match. volumes match each other.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action because of the following reasons: secondary data volume is an open-system volume. • S-VOL Disable is set by Data Retention Utility. • Whether S-VOL Disable is set to the specified secondary data volume. Severity Level Failure Level • The VMA setting differs between the primary data • Whether the VMA setting volume and the secondary differs between the data volume.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level i 0 Check the number of pairs in i the specified restore journal group. 0 • The combination of the emulation types of the journal volumes of the master and restore journal groups is incorrect. • The emulation types of the primary and secondary data volumes are not the same.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message 6505 58291 6505 58292 Recommended Action Severity Level Failure Level The specified secondary data Check the status of the volume is not paired with any specified secondary data another volume. volume. i 0 The specified journal volume Check whether the journal is unusable.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 58298 The specified secondary data volume is used by Concurrent Copy, Compatible XRC or another program product.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level If the primary data volume is in COPY or Pending status, retry the operation after the status of the volume changes to PAIR or Duplex. 6505 58326 The Add Pair (Paircreate) Specify another primary data W operation failed because the volume, and retry the specified primary data operation.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action 6505 58337 The Add Pair (Paircreate) operation failed because the CLPR number of the specified primary data volume was different from the CLPR number of the journal volume in the specified master journal group. Check the CLPR number of W the journal volume in the specified master journal group, and specify the primary data volume that has the same CLPR number.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level a Volume Security setting on volume in the Volume Security the specified secondary data window. volume. 6505 58348 The Paircreate operation failed because a Data Retention Utility VMA was set up on the specified primary data volume. From the Data Retention Utility window, check the settings of the specified primary data volume.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level • A volume used by Flex Copy XP. • An XP Thin Provisioning volume used a P-VOL of Business Copy. • An XP Thin Provisioning volume and a source volume of Auto LUN. 6505 58354 The specified primary data volume is used by another program product.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level volume. Specify a mirror ID other than 0 if you use this volume to create a pair. 6505 58458 A different mirror ID has Specify the same mirror ID as W already been registered in the registered mirror ID, and the specified master journal then retry the operation. group. Only one mirror ID can be registered in one journal group, so specify the same mirror ID.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action or the Universal Replicator for Mainframe function of the secondary subsystem does not support external volumes. and call HP technical support to confirm whether the XP Continuous Access Journal or the Universal Replicator for Mainframe function supports external volumes.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 58530 The capacity of the specified Check the capacity of the W volume is too small. volume, and specify a volume with larger capacity. 0 6505 58531 A journal volume cannot be Check the emulation types of W added because the the specified volumes. combination of the emulation types for the journal volumes is not correct.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level If this problem persists, call HP technical support and request to format the volume. 6505 58564 The Add Pair (Paircreate) operation failed because the specified primary data volume is being shredded by Data Retention Utility. Confirm that the shredding W has completed in the Data Retention Utility window, and then retry the operation.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level the primary data volume and the secondary data volume. 6505 58595 The Paircreate operation failed because the XP Continuous Access Journal function of the secondary subsystem does not support LUSE volumes. Confirm that the XP W Continuous Access Journal function of the secondary storage system supports LUSE volumes.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level mirror ID which exists in the EXCTG. 6505 58606 Journal groups cannot be Check the status of the deleted from the extended specified extended consistency group (EXCTG), consistency group (EXCTG). because the specified EXCTG was not registered.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 58616 The specified journal group Check the state of the journal W cannot be added to extended group in the storage system consistency group (EXCTG). where the specified journal group belongs to, or the installation status of the program product.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level If this problem persists, call HP technical support. 6505 58641 The specified volume cannot be used as a journal volume because the volume is set by Cache Residency Manager or Cache Residency Manager for Mainframe. Confirm whether the specified W volume is set by Cache Residency Manager or Cache Residency Manager for Mainframe.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 58686 The specified operation failed Check the attribute of the because the attribute of the journal group of the remote journal group of the remote storage system. subsystem was not restore. W 0 6505 58687 The status of the other mirror If the problem persists despite W of the Delta resync did not retrying, call HP technical change. support.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action 6505 58694 The Delta resync operation failed. Check the status of the secondary data volume, or the status of the connected communication line. Check the status of the W secondary data volume, or the status of the connected communication line. When no abnormality is found in the status of the secondary data volume or the communication line, call HP technical support.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Delta resync cannot be executed. Delete the pair ready for Delta resync and copy all data in the primary data volume. volume should meet the following requirements. • The specified volume is a secondary data volume of another mirror. • The pair status of the specified volume is PAIR or Duplex.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level W 0 5 specified secondary data volume was Not Ready. 6505 58708 The Add Pair (Paircreate) If the same problem persists operation to get ready for despite retrying, call HP Delta resync failed, or the technical support. recovery to the status ready for Delta resync failed. If the same problem persists despite retrying, call HP technical support.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level The related program products The related program products are: are: 6505 58719 • XP Continuous Access or TrueCopy for Mainframe • XP Continuous Access or TrueCopy for Mainframe • XP Continuous Access Journal or Universal Replicator for Mainframe • XP Continuous Access Journal or Universal Replicator for Mainframe The licensed capacity of XP Continuous Access or
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 66002 The processing mode in the spreadsheet declaration statement is invalid. Check the contents of the spreadsheet. E 5 6505 66004 The description of the operation tag is invalid. Check the contents of the spreadsheet. E 5 6505 66568 Multiple operation tags are defined. Check the contents of the spreadsheet.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 66603 The value entered as CU (S-VOL) is outside the setting range. Check the contents of the spreadsheet. E 5 6505 66604 The number of digits of LDEV Specify the volume in an (S-VOL) is invalid. external storage system. E 5 6505 66605 The format of LDEV (S-VOL) is invalid. Check the contents of the spreadsheet.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 66623 The value entered as CU (paired VOL) is outside the setting range. Check the contents of the spreadsheet. E 5 6505 66624 The number of digits of LDEV Check the contents of the (paired VOL) is invalid. spreadsheet. E 5 6505 66625 The format of LDEV (paired VOL) is invalid. Check the contents of the spreadsheet.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 66644 The value entered as ControllerID is outside the setting range. Check the contents of the spreadsheet. E 5 6505 66645 The number of digits of PathGroup is invalid. Check the contents of the spreadsheet. E 5 6505 66646 The format of PathGroup is invalid. Check the contents of the spreadsheet.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 66665 The value entered as DeleteMode is outside the setting range. Check the contents of the spreadsheet. E 5 6505 66666 The number of digits of S-VOLWrite is invalid. Check the contents of the spreadsheet. E 5 6505 66667 The format of S-VOLWrite is invalid. Check the contents of the spreadsheet.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level but Disable was not set for S-VOLWrite. 6505 66685 When the pair was operated, Check the contents of the Volume was set for Range but spreadsheet. Flush was not set for SuspendMode. E 5 6505 68003 The operation failed because Check whether the specified the specified journal group journal group is registered. was not registered.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 68014 The operation failed because Check whether the specified the specified volume was a volume is a pool volume of pool volume of XP Thin XP Thin Provisioning. Provisioning. W 0 6505 68015 The operation failed because Check whether the specified W the specified primary data primary data volume is an XP volume was an XP Thin Thin Provisioning volume.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 68759 The status of the specified volume is Simplex or SMPL. Check the contents of the spreadsheet. W 0 Check whether the LDEV number or LUN, and mirror ID of the specified volume are correct. 6505 66778 The Add Pair (Paircreate) Check whether the specified operation failed because the primary data volume is a specified primary data System Disk.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message or XP External Storage Access Manager. • The volume was used by XP Continuous Access or XP External Storage Access Manager, but the pair status was not PSUS or PSUE. Recommended Action Severity Level Failure Level External Storage Access Manager cooperates. Delete the XP Continuous Access or XP External Storage Access Manager pair volume or suspend it.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message 6505 68848 6505 Recommended Action Severity Level Failure Level The operation failed, because Wait until the initializing the specified primary data process is completed, and volume was being initialized then retry the operation. by Business Copy or ShadowImage for Mainframe.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level storage system connected to the mirror. 6505 68861 The operation failed, because Confirm the status of the the specified journal group specified journal group. was not in the configuration of 3DC cascade or 3DC multi target. W 0 6505 68862 The specified remote command device cannot be assigned to a mirror any further.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level W 5 restore journal group was in one of the following statuses: • It is a master journal group of the first mirror. • It is a restore journal group of the first mirror. 6505 68905 The operation failed because Verify the attribute of the the attribute of the specified specified journal group. journal group was Master & Restore.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Extended was not installed in installed in the master storage the master storage system. system. 6505 68913 The operation failed because the Disaster Recovery Extended was not installed in the restore storage system. Verify that the Disaster W Recovery Extended is installed in the restore storage system.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level • It is a volume that combined with XP Continuous Access. • It is a volume that combined with Copy-on-Write Snapshot. • It is a volume that combined with XP Auto LUN. 6505 68918 The operation to create a Verify the master journal pair of the second mirror group.
Table 55 Error Codes — Part Code 6507 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6507 5036 Two or more commands which were not able to be processed were demanded. Check the settings, and retry E the operation. 5 6507 6012 An error occurred during SVP If the problem persists despite E processing. If this problem retrying, call HP technical persists, call HP technical support. support.
Table 56 Error Codes — Part Code 6510 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6510 7302 An error occurred in client logic. Call HP technical support. E 2 6510 7303 An error occurred in client logic. Call HP technical support. E 2 6510 7440 An error occurred during processing. If this problem persists, call HP technical support. If the error occurs after retrying, call HP technical support.
Table 56 Error Codes — Part Code 6510 (continued) 310 Part Code Error Number Error Message Recommended Action Severity Level 6510 9105 The value that is under setup To discard the current settings i is not reflected yet. Do you and exit the window, click want to exit? [OK]. Otherwise, click [Cancel]. 0 6510 9106 The value that is under setup To discard the current settings i is not reflected yet. Do you and switch to View mode, want to change the mode? click [OK]. Otherwise, click [Cancel].
Table 56 Error Codes — Part Code 6510 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6510 9128 The specified volume was not Click [OK], and then specify i found. the correct volume. 0 6510 9155 The history file has been updated. Select the OK button to display the history logs from the beginning. Click [OK]. i 0 6510 9303 There are no valid volumes. Check the device emulation or the definition of the SCSI path.
Table 56 Error Codes — Part Code 6510 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6510 55202 The specified controller ID cannot be used. Check the specified controller W ID. 0 6510 55207 Some of the specified values are incorrect. Two times the value of M-JNL Cache plus the value of R-JNL Cache must be equal to or less than 100.
Table 56 Error Codes — Part Code 6510 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6510 59006 No more journal volumes can Check the number of journal i be registered, or too many volumes in the specified volumes are selected. journal group, or check the number of the selected volumes. 0 6510 59007 Are you sure you want to delete the specified subsystems? To delete the specified storage system, click [OK]. Otherwise, click [Cancel].
Table 56 Error Codes — Part Code 6510 (continued) Part Code Error Number Error Message Severity Level Failure Level 6510 59039 You cannot add journal Purchase a license for XP volumes because XP Continuous Access Journal, Continuous Access Journal is and then install it. not installed. W 0 6510 59042 There are no valid journal groups. All journal groups are used W by Universal Replicator for Mainframe or XP Continuous Access Journal.
Table 56 Error Codes — Part Code 6510 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level different from the CLPR as the CLPR number of the number of the data volume in volume in the Preview list. the Preview list. In this operation, specify only one CLPR number. 6510 59113 There are two or more CLPR numbers for the specified volume, or you tried to register a volume different from the CLPR number of an existing volume.
Table 56 Error Codes — Part Code 6510 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6510 59327 You cannot specify [Entire] or Check the status of the [None] to the Initial copy specified master journal mode under the current status group. of the specified master journal group. Check the status of the specified master journal group.
Table 56 Error Codes — Part Code 6510 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level mirrors available to assign a remote command device. 6510 65780 The same mirror ID is Specify different mirror IDs in W specified in the mirror 1 and the mirror 1 and the mirror 2 the mirror 2 parameters. parameters. 0 6510 65805 The current microprogram version of DKCMAIN does not support creating a pair by selecting primary or secondary data volume.
Table 56 Error Codes — Part Code 6510 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6510 69016 Are you sure you want to cancel the export? To stop the operation, click [OK]. To continue the operation, click [Cancel]. W 0 6510 69017 No more journal groups can Check the number of be registered, because the registered journal groups. number of registered journal groups has reached the maximum.
Table 58 Error Codes — Part Code 6610 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6610 5144 Some of the entered values are incorrect. Check the values and then specify correct values. Check the values, and then specify correct values. W 0 6610 7301 An error occurred in client logic. Call HP technical support. E 2 6610 7302 An error occurred in client logic. Call HP technical support.
Table 58 Error Codes — Part Code 6610 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6610 9100 Do you want to exit? To close the window, click [OK]. Otherwise, click [Cancel]. i 0 6610 9101 Do you want to cancel? To cancel the operation, click i [OK]. 0 6610 9102 Do you want to apply? To apply settings in the Preview list to the disk storage system, click [OK].
Table 58 Error Codes — Part Code 6610 (continued) Part Code Error Number Error Message Recommended Action Do you want to execute the processing? [OK]. Otherwise, click [Cancel]. Severity Level Failure Level 6610 9121 Data has been changed and To execute this operation, the graph has been click [OK]. Otherwise, click displayed. If you continue this [Cancel]. operation, all the data and the graph will become invalid.
Table 58 Error Codes — Part Code 6610 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6610 55037 Too many mirrors in the journal group. Check the number of mirrors i in the journal group. Then delete unused mirrors, or register them in another journal group. 0 6610 55038 Too many mirrors in the subsystem. Check the number of mirrors i in the journal group, and then delete unused mirrors.
Table 58 Error Codes — Part Code 6610 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level subsystems and then retry the operation. 6610 56522 There are no consistency groups available. Create unused consistency groups and then retry the operation. There are no consistency i groups available. Create unused consistency groups, and then retry the operation. 0 6610 56523 No more mirrors can be created for the specified volume.
Table 58 Error Codes — Part Code 6610 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Performance Monitor Export Tool to export the monitoring data file. 6610 59031 The monitoring data saved at present will be deleted when the monitoring switch is set to Enable the next time. To continue processing, click i [OK]. To stop processing, click [Cancel].
Table 58 Error Codes — Part Code 6610 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level maximum. Adjust the number journal volumes to be of journal volumes. deleted. 6610 59100 The same volume is stored more than once in the Preview list. Use the sort function to identify volumes with the same LDKC number, the same CU number and the same LDEV number.
Table 58 Error Codes — Part Code 6610 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level If the amount of Preview data is small or there is no Preview data, too much data is selected. Reduce the number of data, and retry the operation. 6610 59116 The specified function is not supported by the current microprogram version. Check the microcode version W of the DKCMAIN, and then call HP technical support.
Table 58 Error Codes — Part Code 6610 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level extended consistency group journal groups which belong (EXCTG). The timer type for to an extended consistency journal groups which belong group (EXCTG). to EXCTG must be System. 6610 59325 A pair which is ready for Check the status of the Delta resync cannot be specified master journal created under the current group. status of the specified master journal group.
Table 58 Error Codes — Part Code 6610 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6610 65664 The specified volume is not valid for this program product. Specify another volume. Specify another volume. W 0 6610 65665 The specified volume is not Check the monitoring setting. W the volume to be monitored. Check the monitoring setting. 0 6610 65777 The current microprogram version of DKCMAIN cannot assign remote command devices to mirrors.
Table 58 Error Codes — Part Code 6610 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6610 69021 Journal groups cannot be added to the extended consistency group (EXCTG), because the number of EXCTG exceeds the maximum. Check the number of registered EXCTG. W 0 6610 69084 Do you want to release the To continue the operation, remote command device from click [OK]. the mirror? Otherwise, click [Cancel].
Table 59 Error Codes — Part Code 6805 (continued) Part Code Error Number Error Message Recommended Action 6805 55010 An invalid storage resource number (SLPR No.) was detected. Correct the storage resource E number (SLPR No.), and then retry the operation. If this problem persists, call HP technical support. 3 6805 55209 The maximum number of CLPRs that can be created was exceeded. Specify the number of CLPRs E within the valid range. 3 6805 55210 The Block Option setting is incorrect.
Table 59 Error Codes — Part Code 6805 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6805 55221 The CLPR number is duplicated. Correct the setting, and then retry. If the same problem persists despite retrying, call HP technical support. W 5 6805 56524 This function cannot be used Select another window. To by the storage partition set this function, contact the administrator. storage administrator.
Table 60 Error Codes — Part Code 6810 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6810 59046 This function will apply the To continue processing, click i setting to all the target CLPRs. [OK]. To stop processing, This function will overwrite click [Cancel]. the setting on a CLPR if the setting is already applied to the CLPR.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7005 6502 Processing in progress. Please wait for a while, and then retry the operation. Wait a few seconds, and retry the operation. W 0 7005 6503 The target volume status is being changed to SMPL. Wait a few seconds, and retry the operation. i 0 7005 7310 This error code is not registered. If this problem persists, call HP technical support.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level the status of pairs and the commands that can be accepted. 7005 8506 The command has been rejected, because the specified S-VOL or reserved volume is used by the host. Vary the S-VOL or the i reserved volume offline from the mainframe host, and then issue the command again.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Specify the volume of the same emulation type, and retry the operation. Make sure that the capacity is the same for both. 7005 8520 You cannot set a pair, because the volume type is different for each. i 0 7005 8521 The number of multiple copy Check the contents, and retry. i jobs exceeded the maximum.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message 7005 8536 7005 Recommended Action Severity Level Failure Level A cache failure was detected. Call HP technical support. E 0 8537 The cache capacities do not match. Call HP technical support. E 0 7005 8538 An SM failure was detected. Call HP technical support. E 0 7005 8539 There is insufficient shared memory to create 4096 pairs. There is insufficient shared memory in DKC.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7005 8553 The S-VOL is not implemented. You cannot execute the operation for the volume which is not implemented. i 0 7005 8554 The command has been W • Restore the blocked rejected, because the volume, and then retry the specified S-VOL is blocked or operation. used as a system disk. • The system disk cannot be specified as an S-VOL. Specify another volume.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action the differential table or pair table to set pairs is insufficient. section in the HP XP24000/XP20000 Business Copy Software User's Guide for the relationship between the number of pairs that can be created and shared memory. Severity Level Failure Level 7005 8570 The selected volume does not Refresh the window, and exist. retry the operation.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7005 8586 The number of groups that can be set in the same subsystem is invalid. Check the contents, and retry. i 0 7005 8587 The number of pairs that can Check the contents, and retry. i be set in the same group is invalid. 0 7005 8588 The specified group number is not set. Check the contents, and retry.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level 7005 8602 The command has been The volume used as an S-VOL W rejected, because the of the other pair cannot be specified P-VOL has already used as a P-VOL. been used as an S-VOL of the other pair. 5 7005 8605 The Pairresync command was Check the pair status. issued to a device in the SMPL status.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Guide for the relation between the state of XP Continuous Access pair or XP External Storage Access Manager pair and the XP Business Copy operations. 7005 8615 The command has been rejected because the specified S-VOL is used as S-VOL of XP Continuous Access pair or XP External Storage Access Manager pair.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7005 8631 The specified CU number is invalid. Call HP technical support. i 0 7005 8632 The timing of issuing the command is invalid. Call HP technical support. E 0 7005 8633 The abnormal status is invalid. Call HP technical support.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Operations sections in the HP XP24000/XP20000 Business Copy Software User's Guide for the relationship between the state of pairs and the XP Business Copy operations. 7005 8644 The command has been rejected, because the pair status is not PSUS or PSUE. Check the pair status.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7005 8657 The Swap&Freeze option Call HP technical support. cannot be specified, because mode 80 is on. E 5 7005 8670 The number of volumes composing the LUSE volume specified as the P-VOL does not match the number of volumes composing the LUSE volume specified as the S-VOL.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level persists, call HP technical support. 7005 57102 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 7005 58000 The command has been Select a different volume or i rejected because the cascade release the consistency group request for creating cascade setting.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Manager pair and the XP Business Copy operations. 7005 58261 The command has been rejected, because the specified P-VOL is used as an S-VOL of XP Continuous Access pair. The requested command W cannot be executed in the current status of XP Continuous Access pair.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level specified P-VOL is a P-VOL for XP Snapshot. 7005 58477 The operation cannot be performed, because the specified P-VOL is a V-VOL for XP Snapshot. Specify another volume. W 5 7005 58478 The operation cannot be performed, because the specified P-VOL is a pool volume. Release the pool volume, or select another volume.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message 7005 58535 7005 Recommended Action Severity Level Failure Level The reserve volume setting Release the journal volume failed because the specified setting, or specify another volume was a journal volume. volume. W 2 58536 The operation failed because Check the requirements for the specified S-VOL was a using the volume with XP data volume of XP Continuous Continuous Access Journal. Access Journal.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action XP Snapshot pair in COPY (RS-R) status. conjunction with XP Snapshot. Severity Level Failure Level i 0 7005 58585 The operation failed because Volumes that do not belong the CU group of the specified to CU group 0 are currently volume is not supported. not supported. Specify another volume.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Provisioning volume not associated with a pool. 7005 68739 The command has been rejected, because the specified reserved volume is an XP Thin Provisioning volume not associated with a pool. Associate the XP Thin Provisioning volume with a pool, and then retry the operation.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Asynchronous, and also CLPR numbers of P-VOL and S-VOL of Business Copy are different in the specified pair. 7005 68808 The command has been rejected, because the specified P-VOL is an XP Thin Provisioning volume whose capacity is being added. The operation is not available i because the target volume has capacity changes.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message 7005 68867 7005 7005 Recommended Action Severity Level Failure Level The command has been Specify another volume. rejected, because the volume specified as P-VOL is a quorum disk. i 0 68868 The command has been Specify another volume. rejected, because the volume specified as S-VOL is a quorum disk. i 0 68869 The command has been Specify another volume.
Table 63 Error Codes — Part Code 7010 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7010 5123 The password is invalid. Check the password. W 0 7010 5124 You cannot select more than one operation at a time. Multiple volumes cannot be W processed in the operation. Process one volume at a time. 0 7010 5125 No target volume is selected. Select the target volume.
Table 63 Error Codes — Part Code 7010 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7010 9102 Do you want to apply? Click [OK] to execute the operation. i 0 7010 9108 The option has been To continue processing, click W changed. If you continue [OK]. Otherwise, click processing before applying [Cancel]. the change, the option will be reset to the current setting.
Table 63 Error Codes — Part Code 7010 (continued) Part Code Error Number Error Message Recommended Action 7010 66560 The maximum number of Change the number of pairs Pairs or Volumes that can be or volumes displayed in displayed in the Preview List Preview to 16,384 or less. is 16,384. Change the number of pairs or volumes being displayed in the Preview List to 16,384 or less.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level previous command is being processed. 7105 8502 You cannot reserve the Delete the XP Continuous volume, because a XP Access pair. Continuous Access pair exists in the same subsystem frame. i 0 7105 8503 You cannot create the new Delete the XP Continuous pair, because a XP Access pair. Continuous Access pair exists in the same subsystem frame.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level 7105 8512 Cannot perform Resync or Suspend operation because of the path group setting. Vary the S-VOL offline from i the mainframe host, and then issue the command again. 0 7105 8513 The command has been Vary the S-VOL offline from i rejected, because the the mainframe host, and then specified S-VOL is used by the issue the command again. host.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7105 8530 An internal logic error occurred. Call HP technical support. E 0 7105 8531 An internal logic error occurred. Call HP technical support. E 0 7105 8532 The command has been Stop the usage by the host. rejected, because the S-VOL or the T-VOL is being used by the host.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level 7105 8544 16 Mbytes of shared memory Check the contents, and retry. i is available. 0 7105 8545 A power supply failure is detected. Call HP technical support. E 0 7105 8546 The command was rejected. The PS OFF is in progress. Retry the operation with power ON. i 0 7105 8547 A data transfer failure is detected (CHA). Call HP technical support.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level 7105 8558 The command has been rejected, because the specified volume is blocked or used as a system disk. E • Restore the blocked volume, and then retry the operation. Failure Level 5 • The system disk cannot be specified as a reserved volume. Specify another volume. 7105 8559 The volume is being formatted. Wait until the volume is formatted, and retry the operation.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7105 8575 The selected volume is not a reserved volume. Check the status of the volume. i 0 7105 8576 No reserved volume is available for use. Check the contents, and retry. i 0 7105 8577 The number of reserved volumes to be defined exceeds the maximum. Stop the operation of the Reserve volume setting, or delete the Reserve volume.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message 7105 8593 7105 Recommended Action Severity Level Failure Level The S-VOL is a source volume Release the XP Auto LUN for Auto LUN. setting. i 0 8594 The S-VOL is a target volume Release the XP Auto LUN for Auto LUN. setting. i 0 7105 8595 The specified S-VOL does not Refresh, and then retry the exist. operation. i 0 7105 8596 The specified volume is a reserved volume.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Mainframe User's Guide: HP XP24000 Disk Array, HP XP20000 Disk Array for the relationship between the state of TrueCopy for Mainframe pair and the ShadowImage for Mainframe operations. 7105 8608 The specified T-VOL is not defined. Refresh the window, and retry the operation. i 0 7105 8609 The specified volume is not set as a reserved volume.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level specified volume is used as a used as a reserved volume. R-VOL of TrueCopy for Specify another volume. Mainframe pair. 7105 8624 The command has been Confirm whether the volumes W rejected, because there is no specified for S-VOL and pair available. T-VOL are correct. 5 7105 8625 The P-VOL(S-VOL) and S-VOL(T-VOL) have the same number.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level in Cache Residency Manager Manager for Mainframe for Mainframe. setting for the operation. 7105 8640 The command has been Wait until Reverse Copy or rejected, because the pair Quick Restore completes. sharing the S-VOL was in the Reverse Copy or Quick Restore status. i 0 7105 8641 The pairs contain a pair in the Reverse Copy status.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action 7105 8651 The SSID is invalid. Check the contents, and retry. i 0 7105 8652 The boot device is not an S-VOL nor T-VOL. Check the target volume number. i 0 7105 8653 Because the boot device is the S-VOL in the DeletePair command, the flag does not match. Check the target volume number.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level version does not support the CT Group operation. 7105 8946 A pair status cannot be Reset the Split time of changed because the Split Consistency Group from the time of Consistency Group is mainframe host. set. i 0 7105 8991 The command has been rejected, because the FlashCopy Mirroring V2 relationship exists.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message 7105 58000 The command has been Select a different volume or i rejected because the cascade release the consistency group request for creating cascade setting. pairs composed of volumes belonging to the same consistency group was issued. 0 7105 58001 The Add Pair command for Wait until the L1 pair status adding the L2 pair has been changes to Split, and then rejected because the L1 pair retry the operation.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level ShadowImage™ for Mainframe User's Guide: HP XP24000 Disk Array, HP XP20000 Disk Array for the relationship between the state of TrueCopy for Mainframe pair and the ShadowImage for Mainframe operations. 7105 58262 A pair cannot be created because shared memory for differential tables is insufficient. Add sufficient shared memory E to create a pair.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level microcodes coexisted in the storage system. 7105 58533 The operation failed, because Release the journal volume the specified S-VOL was a setting or specify another journal volume. volume. W 2 7105 58534 The operation failed, because Release the journal volume the specified T-VOL was a setting or specify another journal volume. volume.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level by Delta resync of Universal Replicator for Mainframe. for Delta resync cannot be specified as an S-VOL. Specify another volume. Failure Level 7105 58632 The reserve volume setting failed because the specified volume was used by Delta resync of Universal Replicator for Mainframe.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level for Mainframe pair and the ShadowImage for Mainframe operations. 7105 68767 The XP Business Copy Operation for FICON(R) Data Migration failed, because the specified pair consisted of an S-VOL other than a FICON(R) Data Migration Source Volume, or a T-VOL that is a FICON(R) Data Migration Source Volume.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level T-VOL of the specified pair was used by External Storage. 7105 68775 The command has been rejected, because the S-VOL of the specified pair is a FICON(R) Data Migration Source Volume. The specified operation i cannot be executed in the current pair configuration.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7105 68834 The command has been rejected, because the specified CTG is used by Business Copy. Use another CTG, or release i the pair of XP Business Copy where the specified CTG is in use. 0 7105 68854 The XP Business Copy Operation for FICON(R) Data Migration failed, because more than one T-VOL was assigned for the specified S-VOL.
Table 65 Error Codes — Part Code 7110 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7110 7440 An error occurred during processing. If this problem persists, call HP technical support. If this problem persists, call HP technical support. E 2 7110 8001 A time-out error occurred. Wait for the subsystem to recover to the normal condition, and then retry the operation. Retry the operation. If you get E the same message again, reboot the computer.
Table 65 Error Codes — Part Code 7110 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level W 5 Correct the number of selected S-VOLs and T-VOLs. 7110 55597 The entered values are Check the values, and then incorrect. Check the values enter correct values. and then enter correct values. 7110 58619 The operation cannot be Refresh the window, and then E executed because an invalid retry the operation. value is contained in the obtained information.
Table 65 Error Codes — Part Code 7110 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Recommended Action Severity Level Failure Level E 2 included in the specified pairs. Table 66 Error Codes — Part Code 8005 Part Code Error Number Error Message 8005 2002 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 66 Error Codes — Part Code 8005 (continued) Part Code Error Number Error Message 8005 6040 8005 Recommended Action Severity Level Failure Level An error occurred while Call HP technical support. connecting to the subsystem. Wait for a while, and then retry the operation. E 6 6050 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 66 Error Codes — Part Code 8005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level of Cache Residency Manager areas. CLPR No:%s 8005 55246 The total number of Cache Check the settings, and then Residency Manager areas set retry the operation. for the CLPRs and the maximum number of the Cache Residency Manager areas in the subsystem are not equal.
Table 66 Error Codes — Part Code 8005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level storage administrator. To perform other operations, select a function button. 8005 56526 The resources of other SLPR(s) Correct the settings, and then E cannot be accessed. retry the operation. 6 8005 57101 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 66 Error Codes — Part Code 8005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8005 68761 An error occurred on the DKC side. If this problem persists, call HP technical support. An error occurred on the DKC side. If this problem persists, call HP technical support. E 3 8005 68762 This functionality is not available. DKA Encryption License Key is required. Install the required program product.
Table 67 Error Codes — Part Code 8105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level E 6 The configuration information E has been already changed. 6 • Volumes reserved by Auto LUN • System Disk volume 8105 1007 Failed to remove the path. Check the setting. The specified path is the last path of the volumes used for XP Continuous Access, Business Copy, Auto LUN, or XP Snapshot.
Table 67 Error Codes — Part Code 8105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level cannot be processed in this agent. The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact HP technical support. 8105 1022 An error occurred. If this problem persists, call HP technical support. Host mode is invalid. (The E specified value is not in the specification.
Table 67 Error Codes — Part Code 8105 (continued) Part Code Error Number Error Message Recommended Action Check the setting. it is guarded in the screen. In the unlikely event that this error occurs, contact HP technical support. Severity Level Failure Level 8105 1061 An error occurred. If this problem persists, call HP technical support. You are trying to perform E LUN Security operation for a port where LUN Security function is invalid.
Table 67 Error Codes — Part Code 8105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level W 5 change the command device requested for volumes other configurations: than open volumes (including • Volumes reserved by Auto uninstalled volumes). The error does not occur normally LUN because it is guarded in the • Volumes other than the screen. In the unlikely event open-system volumes that this error occurs, contact (including unmounted HP technical support.
Table 67 Error Codes — Part Code 8105 (continued) Part Code Error Number Error Message enable command device security on the volume. 8105 1125 There are no host groups where the WWN will be registered. Recommended Action Severity Level Failure Level error occurs, contact HP technical support. The configuration information E has been already changed. 6 Check the settings, and request the setting of the configuration information again.
Table 67 Error Codes — Part Code 8105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level the maximum that can be set Check the settings, and in a port. request the setting of the configuration information again. 8105 1135 An error occurred. If this problem persists, call HP technical support. When the PORT information E (Fibre Address/Fibre Topology/Channel Speed) is set, multiple change instructions are set to the same port.
Table 67 Error Codes — Part Code 8105 (continued) Part Code Error Number Error Message Recommended Action 8105 1201 The selection of High Speed mode/MIX mode is invalid. The specified port cannot be changed to High Speed mode/MIX mode. Change the parameter to a E path where the High Speed mode/MIX mode can be set, and then retry the operation. 5 8105 1203 High Speed mode/MIX mode was specified.
Table 67 Error Codes — Part Code 8105 (continued) Part Code Error Number Error Message Recommended Action Severity Level 8105 1355 The host mode of the host group connected to the Initiator port cannot be changed. The port you are trying to set E is for XP Continuous Access. You must change the attribute (Target or RCU Target) when adding a WWN. 6 8105 1356 The host group cannot be added to the Initiator port. The port you are trying to set E is for XP Continuous Access.
Table 67 Error Codes — Part Code 8105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8105 1911 The specified volume contains Select another volume. Pool-VOLs. E 6 8105 1912 The specified volume is a Correct the settings, and then E remote command device, and retry the operation. therefore the command device setting or the command device security setting cannot be set or released.
Table 67 Error Codes — Part Code 8105 (continued) Part Code Error Number Error Message Recommended Action 8105 2011 The status of the storage system requires maintenance (for example, the subsystem is blocked, the shared memory is inconsistent, or some other problem occurs). Check the status of the disk E storage system (for example, the storage system is blocked, the shared memory is inconsistent, or some other problem occurs). If this problem persists, call HP technical support.
Table 67 Error Codes — Part Code 8105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Access pair, a XP Continuous defined by Business Access Journal pair, or a Continuity Manager, and Universal Replicator for then retry the operation. Mainframe pair. Alternatively, command devices defined by Business Continuity Manager are included.
Table 67 Error Codes — Part Code 8105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level reserved volume, and then retry the operation. 8105 3002 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 8105 3003 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 67 Error Codes — Part Code 8105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8105 5705 Configuration File Loader is not installed. Install the Configuration File Loader. W 5 8105 5710 The specified CHA does not exist. Correct the name of CHA. W 0 8105 5711 The specified port does not exist. Correct the name of the port.
Table 67 Error Codes — Part Code 8105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8105 5752 The group name does not exist. Correct the group name. W 0 8105 5753 There is a difference between Correct the port ID and the the current port ID/group ID group ID. and the specified one. W 0 8105 5754 The intermediate volume cannot be specified as a command device. Correct the CU and LDEV.
Table 67 Error Codes — Part Code 8105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8105 5790 A program error occurred under internal process. If nothing changes despite retrying, call HP technical support. W 0 8105 6012 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 8105 6023 The SVP is busy.
Table 67 Error Codes — Part Code 8105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Severity Level Failure Level function tag to a decimal numeral. Table 68 Error Codes — Part Code 8107 Part Code Error Number Error Message Recommended Action 8107 5641 The number of lines exceeds Check the setting. the maximum number of lines of a spreadsheet.
Table 69 Error Codes — Part Code 8110 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8110 5634 An error occurred during processing. If this problem persists, call HP technical support. If the same problem persists despite retrying, call HP technical support. E 2 8110 5772 Modify mode released due to inactivity. Restart Modify mode (press the mode-switching button again) to continue. Modify mode released due E to inactivity.
Table 70 Error Codes — Part Code 8111 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8111 5630 The file specified by [File Name on Client] cannot be read. Correct the specified contents, and retry the operation. E 1 8111 5631 The object specified by [File Correct the specified Name on Client] is not a file. contents, and retry the operation. E 1 8111 5632 Modify mode released due to inactivity.
Table 73 Error Codes — Part Code 8310 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level i 0 function exceeds the number On-Demand function, and of ports installed. then retry the operation. 8310 55111 The selected port cannot be Release the port’s path disabled by the On-Demand setting, and then retry the function because it is operation. path-defined.
Table 74 Error Codes — Part Code 8505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level If this problem persists, call HP technical support to reboot the SVP computer. E 3 E 3 persists, call HP technical support. 8505 8001 A communication time-out error occurred. 8505 8002 An error occurred during SVP If the same problem persists processing. If this problem despite retrying, call HP persists, call HP technical technical support. support.
Table 74 Error Codes — Part Code 8505 (continued) Part Code Error Number Error Message Recommended Action SLPR No:%s If this problem persists, call HP technical support. SLPR No:%s Severity Level Failure Level 8505 55016 The value set as the maximum number of connections to each SLPR is invalid. SLPR No:%s Set the correct value for the E maximum number of connections to the SLPR, and then retry the operation. If this problem persists, call HP technical support.
Table 74 Error Codes — Part Code 8505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level retrying, call HP technical support. 8505 55026 The specified port name (port Specify the correct port name E number) is invalid. (port number), and then retry the operation. If this problem persists, call HP technical support. 5 8505 55027 The cache size is incorrect. Correct the settings of the E cache size, and then retry the operation.
Table 74 Error Codes — Part Code 8505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8505 56527 While another user is logged into Remote Web Console, you cannot edit the information of the SLPR that the user owns. SLPR No:%s Confirm that no user is logged into Remote Web Console, and then retry the operation. E 5 8505 56536 The installation status of the SLPR has changed.
Table 74 Error Codes — Part Code 8505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level system. Wait for a while, and then retry the operation. 8505 58317 CLPR capacity is being Wait a few seconds, and changed in the storage then retry the operation. system. Wait for a while, and then retry the operation. W 5 8505 58318 An error occurred on the If this problem persists, call DKC, while obtaining HP technical support.
Table 76 Error Codes — Part Code 8510 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8510 5030 The display information has not been changed. Specify what you want to register, and retry the operation. W 0 8510 7060 An error occurred in client logic. If this problem persists, call HP technical support. E 2 8510 7301 An error occurred in client logic. If this problem persists, call HP technical support.
Table 76 Error Codes — Part Code 8510 (continued) Part Code Error Number Error Message 8510 55636 The CLPR that has some Migrate all parity groups in parity groups cannot be the CLPR to another CLPR, deleted. Migrate all parity and then delete the CLPR. groups in the CLPR to another CLPR, and then delete the CLPR. 8510 57001 The partition configuration may contain some inconsistent information. To initialize partition configuration, select the Yes button. To stop the operation, select the No button.
Table 76 Error Codes — Part Code 8510 (continued) Part Code Error Number Error Message 8510 59110 8510 59114 Recommended Action Severity Level Failure Level SSIDs that are associated Check the settings. with the selected CU cannot be added to this SLPR, because too many SSIDs have been set in the SLPR. Delete unnecessary SSIDs from this SLPR, and then retry the operation. W 0 Ports in high-speed mode are Check the settings. set across multiple SLPRs.
Table 77 Error Codes — Part Code 8605 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8605 66822 The contents of the e-mail address information file are invalid. Register the email address information file again. E 5 8605 66823 A failure occurred while Check the state of E communicating with the SMTP communication with the SMTP server. server to solve this problem.
Table 78 Error Codes — Part Code 8610 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8610 65765 The same e-mail addresses are specified. Remove the duplicated email W addresses, and then register it again. 5 8610 69081 Send a test message. OK? Confirm the message, and then reply. i 5 8610 69082 Sending test message has been completed. Confirm the message, and then reply.
Table 79 Error Codes — Part Code 9005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level persists, call HP technical support. 9005 7112 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 9005 7113 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 80 Error Codes — Part Code 9007 Part Code Error Number Error Message 9007 5099 9007 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 6012 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 82 Error Codes — Part Code 9105 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 9105 5511 The program product is not installed. Click [OK], and then install the program product. W 5 9105 5600 The settings of the security group are invalid. Click [OK], correct the security group settings, and then retry the operation. W 0 9105 5601 The settings of the host group Click [OK], correct the host W are invalid.
Table 82 Error Codes — Part Code 9105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level persists call HP technical support. 414 9105 7111 An error occurred during SVP processing. If this problem persists, call HP technical support. An error occurred during SVP E processing. If this problem persists, call HP technical support. 3 9105 7310 Unregistered error code. If this problem persists, call HP technical support.
Table 83 Error Codes — Part Code 9107 Part Code Error Number Error Message Recommended Action Severity Level 9107 6012 An error occurred during SVP processing. If this problem persists, call HP technical support. An error occurred during SVP E processing. If this problem persists, call HP technical support. 9107 7060 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 84 Error Codes — Part Code 9110 (continued) 416 Part Code Error Number Error Message Recommended Action 9110 5619 The R-VOL/T-VOL cannot be set to the specified security group. Click [OK]. Ensure that the W R-VOL/T-VOL is not set to the specified security group, and retry the operation. 9110 5620 The selected volumes include Click [OK], check the some invalid volumes. selected volumes, and retry the operation. W 0 9110 5621 No item is selected.
Table 84 Error Codes — Part Code 9110 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 9110 9084 The specified group includes To delete the group, click some hosts. Are you sure you [Yes]. Otherwise, click [No]. want to delete the group? i 0 9110 9101 Do you want to cancel? To cancel the operation, click i [Yes]. Otherwise, click [No]. 0 9110 9102 Do you want to apply? To apply, click [Yes]. Otherwise, click [No].
Table 85 Error Codes — Part Code 9205 (continued) 418 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 9205 5041 The number of issued commands exceeds the maximum. Reduce the number of set demands. W 5 9205 5511 The program product is not installed. Install the program product. W 5 9205 6012 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 85 Error Codes — Part Code 9205 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 9205 8126 The logical volume is configured as a command device. Check the logical volume E configuration, and then retry the operation. 9205 8136 The command was rejected, The currently licensed because the licensed capacity capacity is insufficient. To was exceeded. increase the licensed capacity, buy a new license key.
Table 85 Error Codes — Part Code 9205 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 9205 66008 The number of digits is invalid. Check the contents of the Volume Retention Manager spreadsheet. E 5 9205 66009 The entered value is outside the setting range. Check the contents of the Volume Retention Manager spreadsheet. E 5 9205 66010 The format is invalid. Check the contents of the Volume Retention Manager spreadsheet.
Table 87 Error Codes — Part Code 9605 Part Code Error Number Error Message 9605 5013 9605 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 5030 No commands are issued. Issue a command again. E 5 9605 5041 The number of issued commands exceeds the maximum. Decrease the number of commands.
Table 87 Error Codes — Part Code 9605 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 9605 8120 The specified logical volume does not exist. Specify an open-system volume. E 5 9605 8122 This logical volume is busy. Retry a little later. E 5 9605 8123 This function is not supported. Check whether the E DKCMAIN microcode version and the SVP microcode version are mismatched. 5 9605 8124 This logical volume is a mainframe volume.
Table 87 Error Codes — Part Code 9605 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level whose access attribute is not Read Only or Protect. 9605 8151 You cannot shorten the retention term of the logical volume. To shorten it, call HP technical support. You cannot shorten the E retention term of the logical volume. To shorten it, call HP technical support. 5 9605 8152 You cannot set a retention term to any mainframe volumes.
Table 87 Error Codes — Part Code 9605 (continued) Part Code Error Number Error Message 9605 58414 9605 Recommended Action Severity Level Failure Level The attribute of the P-VOL or Select another volume. the S-VOL of the XP Snapshot cannot be changed. E 5 58415 The VMA of the pool volume Select another volume. cannot be changed. E 5 9605 58417 The VMA of the P-VOL or the Select another volume. S-VOL of the XP Snapshot cannot be changed.
Table 87 Error Codes — Part Code 9605 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 9605 58433 An access attribute is set to the specified extent. Release the access attribute of the extent. E 5 9605 58434 This logical volume is busy. Retry a little later. E 5 9605 58435 This logical volume is busy. Retry a little later. E 5 9605 58436 The access attribute of the logical volume has already been changed.
Table 87 Error Codes — Part Code 9605 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level that of the external volume 1. Execute the Volume with which the logical volume Initialize operation on the is mapped. external group to which the logical volume belongs in the Customized Volume window, and create a volume having the same capacity as the external volume. 2.
Table 88 Error Codes — Part Code 9610 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level Recommended Action Severity Level Failure Level deleted. Do you want to continue the operation? Table 89 Error Codes — Part Code 10010 Part Code Error Number Error Message 10010 55011 0 cannot be specified in all Reply to the message. the fields or the Class A field. W 5 10010 55638 The same IP address, user ID Reply to the message.
2 Support and Other Resources Related Documentation • HP XP24000/XP20000 Disk Array Owner Guide • HP XP24000/XP20000 Remote Web Console User Guide You can find these documents on the HP Manuals website: http://www.hp.com/support/manuals In the Storage section, click Disk Storage Systems and then select a product.
After registering, you will receive email notification of product enhancements, new driver versions, firmware updates, and other product resources. HP Websites For additional information, see the following HP websites: • http://www.hp.com • http://www.hp.com/go/storage • http://www.hp.com/support/manuals • http://www.hp.com/storage/spock Documentation Feedback HP welcomes your feedback. To make comments and suggestions about product documentation, send a message to storagedocsFeedback@hp.com.
Glossary A API Application program interface. C CCI Command control interface. An HP RAID manager. CHA Channel adapter. A device that provides the interface between the array and the external host system. Occasionally, this term is used synonymously with the term channel host interface processor (CHIP). CLPR Cache logical partition. CT Consistency. CTG Consistency group. CU Control unit. CU Control unit. CV Customized volume. D DASD Direct-access storage device. DFW DASD fast write.
M M-VOL Main volume. MCU Main control unit. MU Mirror unit. N NVS Nonvolatile storage. P P-VOL Primary volume. P.P. Program Product. PB Petabyte; equals 1,000^5 bytes (for physical storage such as hard disk drives) or 1,024 TB or 1,024^5 bytes (for logical storage). PCB Printed circuit board. PDEV Physical device. PS Power supply. PSUE Pair suspended-error (status). PSUS Pair suspended-split (status). R R-VOL Remote volume. RCP Remote control port. RCU Remote control unit.
V V-VOL Virtual volume. VDEV Virtual device. VLL Virtual LVI/LUN. VMA Volume management area. W WWN 432 Glossary World wide name.