HP StorageWorks XP24000/XP20000 Remote Web Console Error Codes Abstract This document lists the error codes and error messages for HP StorageWorks Remote Web Console for HP StorageWorks XP disk arrays, and provides recommended action for the error conditions.
© Copyright 2007, 2011 Hewlett-Packard Development Company, L.P. Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor's standard commercial license. The information contained herein is subject to change without notice.
Contents 1 Remote Web Console for Storage System Messages and Error Codes................4 Remote Web Console for Storage System Messages......................................................................4 Message Window Format..........................................................................................................4 Remote Web Console Error Codes..............................................................................................5 2 Support and Other Resources..................
1 Remote Web Console for Storage System Messages and Error Codes • “Remote Web Console for Storage System Messages” (page 4) • “Message Window Format” (page 4) • “Remote Web Console Error Codes” (page 5) Unless otherwise specified, the term storage system in this guide refers to the following disk arrays: • HP StorageWorks XP24000 Disk Array • HP StorageWorks XP20000 Disk Array The GUI illustrations in this guide were created using a Windows computer with the Internet Explorer browser.
Fatal error The server is unable to accept the request from Remote Web Console. One possible cause is that some process is in progress at the server. This message does not indicate an error. • Message text: Descriptive text that appears in the message window. It may include variables %s (character string) and %d (numeral). The values of these variables are determined when processing is performed.
Failure Levels. The failure levels for the error codes are: • 0: No Error • 1: Select MSG OK to end forcibly • 2: All Refresh or Exit is valid only • 3: All Refresh, Refresh, or Exit is valid and the buttons, other than the buttons of the functions in which the error occurred, are valid. • 4: To make refresh possible • 5: No status change • 6: No change with refreshing automatically • 7: Remote Web Console is automatically switched to view mode. If necessary, change the mode to Modify.
Table 1 Error Codes — Part Code 0001 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0001 2005 An error occurred during SVP If this problem persists call HP E processing. If this problem technical support. persists, call HP technical support. 2 0001 3000 An error occurred during SVP If this problem persists call HP E processing. If this problem technical support. persists, call HP technical support.
Table 1 Error Codes — Part Code 0001 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0001 4011 A network error occurred. The probable cause is: Log on again. E 1 • A timeout error occurred during communication with the SVP. A network error may occur when the load of another application program working on the same computer with Remote Web Console is high. Increase the value of the RMI timeout period when network error occurs.
Table 1 Error Codes — Part Code 0001 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0001 5400 Since the SVP is busy, the monitoring data cannot be obtained. Wait a few seconds, and then retry. W 3 Do either of the following if two users are displaying the Performance Monitor window or running the Export Tool: • Ask one of the users to display another window. • Ask one of the users to log off. • Wait for one of the users to quit the Export Tool.
Table 1 Error Codes — Part Code 0001 (continued) 10 Part Code Error Number Error Message 0001 5522 0001 Recommended Action Severity Level Failure Level An error occurred during SVP If the same problem persists processing. If this problem despite retrying, call HP persists, call HP technical technical support. support. E 2 5523 An error occurred during SVP If the same problem persists processing. If this problem despite retrying, call HP persists, call HP technical technical support. support.
Table 1 Error Codes — Part Code 0001 (continued) Part Code Error Number Error Message 0001 5637 0001 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 5638 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 1 Error Codes — Part Code 0001 (continued) 12 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0001 6540 No more users can be Delete unnecessary user registered, because the accounts. number of registered users has reached the maximum. Reduce the number of users, and then retry the operation. E 6 0001 6541 A network error occurred. The SVP is not ready, or an error occurred in the SVP. Reboot the SVP computer and E retry the request.
Table 1 Error Codes — Part Code 0001 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0001 56529 The available SLPR does not exist. Contact the storage administrator and have the SLPR set. Contact the storage administrator and have the SLPR set. E 2 0001 56545 The operation failed because Wait a few seconds, and the audit log is being then retry the operation. processed. Wait for a while, and then retry the operation.
Table 1 Error Codes — Part Code 0001 (continued) Part Code Error Number Error Message Recommended Action Severity Level 0001 65734 P9000 or XP Command View Advanced Edition version information ID is invalid. Check the setting, and then retry the operation. P9000 or XP Command View E Advanced Edition version information ID is invalid. Check the setting, and then retry the operation. 0001 66100 The Login could not be Call HP technical support.
Table 2 Error Codes — Part Code 0002 (continued) Part Code Error Number Error Message Recommended Action Severity Level 0002 2005 An error occurred during SVP If this problem persists call HP E processing. If this problem technical support. persists, call HP technical support. 2 0002 2006 An error occurred during SVP If this problem persists call HP E processing. If this problem technical support. persists, call HP technical support.
Table 2 Error Codes — Part Code 0002 (continued) 16 Part Code Error Number Error Message 0002 5010 0002 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 5040 The number of requests Reduce the number of exceeds the maximum requests and retry the number that can be operation. processed. Reduce the number of requests and retry the operation.
Table 2 Error Codes — Part Code 0002 (continued) Part Code Error Number Error Message 0002 6050 0002 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 6051 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 0002 6502 Now processing.
Table 2 Error Codes — Part Code 0002 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0002 56525 Because the settings across the multiple SLPRs are contained, the authority has been shifted to the storage administrator from the storage partition administrator. To continue the operation, contact the storage administrator. To perform other operations, select a function button.
Table 3 Error Codes — Part Code 0003 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0003 1011 An error occurred. If this problem persists, call HP technical support. The volume that links as an E expanded LU extends over CU#. The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact HP technical support. 2 0003 1012 LU path is set to a volume which links as an expanded LU.
Table 3 Error Codes — Part Code 0003 (continued) 20 Part Code Error Number Error Message Recommended Action 0003 1021 An error occurred. If this problem persists, call HP technical support. The specified volume does E not exist. (You have specified wrong CU#:LDEV#.) Or the LDEV (exclusively for mainframe) cannot be processed in this agent. The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact HP technical support.
Table 3 Error Codes — Part Code 0003 (continued) Part Code Error Number Error Message 0003 1030 0003 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 1031 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 3 Error Codes — Part Code 0003 (continued) 22 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0003 1041 The CU number and the LDEV number set in the VLL operation are the same as those of other volumes. Check and correct the settings. If Volume Initialize and Make Volume are specified at the same time, operate them separately. E 6 0003 1042 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support.
Table 3 Error Codes — Part Code 0003 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0003 1063 The specified WWN is already in use. Specify another WWN. Correct the specified contents, and request the setting of the configuration information again. E 6 0003 1064 You are trying to register the same WWN as an already registered one. Check the settings and request the setting of the configuration information again.
Table 3 Error Codes — Part Code 0003 (continued) 24 Part Code Error Number Error Message 0003 1104 0003 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 1105 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, please call HP technical support.
Table 3 Error Codes — Part Code 0003 (continued) Part Code Error Number Error Message Recommended Action 0003 1124 The command device setting and the command device security setting are incorrect. You cannot do any of the following to the same volume: The setting method of E command device/command device security is incorrect. The following settings are invalid. 1. Set command device + Release command device security 2.
Table 3 Error Codes — Part Code 0003 (continued) 26 Part Code Error Number Error Message Recommended Action 0003 1130 You cannot specify the Correct the specified E default nickname when contents, and request again. setting the nickname of a host group or a host. 6 0003 1131 No more host groups can be set, because the number of host groups has reached the maximum (254) that can be set in a port.
Table 3 Error Codes — Part Code 0003 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0003 1138 An error occurred. If this problem persists, call HP technical support. An error occurred. If this problem persists, call HP technical support. E 2 0003 1140 Because the Port Group setting is done, it is impossible to change. Release the Port Group setting. Release the Port Group setting. E 2 0003 1141 Processing in progress.
Table 3 Error Codes — Part Code 0003 (continued) 28 Part Code Error Number Error Message Recommended Action 0003 1182 An error occurred. If this problem persists, call HP technical support. If this problem persists call HP E technical support. 2 0003 1184 The port information is inconsistent with PCB mode information. Correct the port information W or the PCB mode information. 0 0003 1185 You are trying to insert in the linkage operation including LUSE.
Table 3 Error Codes — Part Code 0003 (continued) Part Code Error Number Error Message Recommended Action Severity Level 0003 1357 S-VOLs remain on the Fibre-RCU port. This operation may cause a fatal damage to the S-VOLs. Please stop this operation. If you want to continue this operation, please remove the S-VOLs from the RCU port first. The specified Port is for Fibre E XP Continuous Access. Delete a logical path, and then retry the operation.
Table 3 Error Codes — Part Code 0003 (continued) 30 Part Code Error Number Error Message 0003 1604 0003 Recommended Action Severity Level Failure Level The specified function is not Install the required program available because it requires product. Cache Residency for Mainframe. E 6 1613 Program products are not installed on the specified volume. Install the LUN Manager program product and the Open Volume Management program product.
Table 3 Error Codes — Part Code 0003 (continued) Part Code Error Number Error Message Recommended Action Severity Level 0003 1916 You cannot set the volumes in the same parity group across multiple CU groups. Correct the settings, and then E retry the operation. 6 0003 1917 The volume(s) in CLPR cannot Correct the settings, and then E be set across multiple CU retry the operation. groups. 6 0003 1919 The newly added LDEV has Check the blocked LDEV and W not been formatted.
Table 3 Error Codes — Part Code 0003 (continued) Part Code Error Number Error Message 0003 2010 The LDEV is being used by Check if the host is E the host, or an error occurred performing I/O operations during SVP processing. on the target path or volume. Recovery processing may take about 1 minute. Wait for a while. 6 0003 2011 The status of the storage system requires maintenance (for example, the subsystem is blocked, the shared memory is inconsistent, or some other problem occurs).
Table 3 Error Codes — Part Code 0003 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0003 2045 The current Cache Residency Wait a few seconds, and setting cannot be changed then retry the operation. because the prestaging operation is in progress. Please wait for a while, and then retry the operation. W 6 0003 2080 Prestaging not completed. Wait a few seconds, and E click [Refresh], and then change the same configuration again.
Table 3 Error Codes — Part Code 0003 (continued) 34 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0003 2087 The system is online to the mainframe host. Take the subsystem offline from the host. Take the storage system offline from the host. W 6 0003 2088 The XP Continuous Access pair is suspended. Add an alternative path. Add an alternative path.
Table 3 Error Codes — Part Code 0003 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0003 2095 A maintenance operation is in progress. For example: Wait for a moment and retry.
Table 3 Error Codes — Part Code 0003 (continued) 36 Part Code Error Number Error Message Recommended Action 0003 2200 The Concurrent Copy or Compatible XRC operation is in progress in the target volumes. Cancel the Concurrent Copy job or delete a Compatible XRC pair via the host. If the Concurrent Copy or the E Compatible XRC operation is in progress in the target volumes, cancel the Concurrent Copy job or delete a Compatible XRC pair via the host.
Table 3 Error Codes — Part Code 0003 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0003 2515 One of the following is defined: an XP Continuous Access pair, an XP Continuous Access Journal pair, or a Universal Replicator for Mainframe pair. Release the pair definition or E delete command devices defined by Business Continuity Manager, and then retry the operation. 6 Cancel or suspend the pair definition, and then retry the operation.
Table 3 Error Codes — Part Code 0003 (continued) Part Code Error Number Error Message 0003 3003 0003 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 3004 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 4 Error Codes — Part Code 0004 (continued) Part Code Error Number Error Message 0004 6012 0004 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 6013 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 6 Error Codes — Part Code 0006 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0006 1005 An error occurred. If this problem persists, call HP technical support. Call HP technical support. E 2 0006 1006 An error occurred. If this problem persists, call HP technical support. Call HP technical support. E 2 0006 1007 An error occurred. If this problem persists, call HP technical support. Call HP technical support.
Table 7 Error Codes — Part Code 0007 (continued) Part Code Error Number Error Message 0007 5306 0007 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 5307 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 7 Error Codes — Part Code 0007 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0007 6091 An error occurred while compressing a file. Call HP technical support. E 5 0007 6092 An error occurred while reading a file. If this problem persists, call HP technical support. W 5 0007 6093 The file to be downloaded was not found. The specified file was not W found. Check whether the file exists and retry the operation.
Table 8 Error Codes — Part Code 0010 (continued) Part Code Error Number Error Message Recommended Action 0010 6027 A network error occurred. The probable causes are: You cannot connect to the E SVP because of factors, such as a network error or SVP error. Check the IP address. If the IP address is correct, close the browser (also close the browser of the storage list), and log in again after waiting a while. If the problem persists, call HP technical support. • The SVP was not ready.
Table 8 Error Codes — Part Code 0010 (continued) 44 Part Code Error Number Error Message Recommended Action 0010 8101 The system cannot apply the new configuration. Do you want to refresh? Click [Refresh], and retry the W operation. 5 0010 9376 The capacity for storing the audit log file is running out. Download the audit log file. W 5 0010 55005 The specified file does not exist. Specify the existing file. W 5 0010 56000 An error occurred during file Check the file status. reading.
Table 8 Error Codes — Part Code 0010 (continued) Part Code Error Number Error Message 0010 59109 0010 59319 Recommended Action Severity Level Failure Level The free space to store the Download the audit log file. audit log file has run out. The old audit log information is deleted because it is overwritten with the new audit log information. W 5 It is important to save your Click [OK]. settings by using the Download File panel located on the Remote Web Console's Control Panel.
Table 9 Error Codes — Part Code 0105 (continued) 46 Part Code Error Number Error Message Recommended Action 0105 2086 The configuration of XP Continuous Access, Business Copy, ShadowImage for Mainframe, Auto LUN, Compatible FlashCopy(R), XP Snapshot, or Flex Copy XP has been defined. Reset the configuration definition, and then retry the operation.
Table 9 Error Codes — Part Code 0105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0105 2095 A maintenance operation is in progress. For example: Wait a few seconds and retry.
Table 9 Error Codes — Part Code 0105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0105 2511 The restore operation has failed, because the specified LDEV was not shredded or formatted. Shred or format the specified i LDEV. If the specified LDEV is an XP Thin Provisioning volume (TP-VOL), recover the pool first. 6 0105 2512 The restore operation has failed, because the system cannot access the specified LDEV. Call HP technical support.
Table 9 Error Codes — Part Code 0105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0105 2519 A Business Copy or Cancel the reserve volume, E ShadowImage for Mainframe and then retry the operation. reserve volume is defined. Cancel the reserve volume, and then retry the operation. 6 0105 2520 An Auto LUN pair is defined. Cancel the pair definition, E Cancel the pair definition, and then retry the operation. and then retry the operation.
Table 9 Error Codes — Part Code 0105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0105 6535 You cannot make changes Delete a logical path, and because a logical path to the then make configuration volume still remains. changes. E 6 0105 6536 The target volume cannot be Release the LUSE volume, E changed due to its LUSE and then request configuration. configuration changes again. 6 0105 8000 An error occurred during SVP Retry the operation.
Table 9 Error Codes — Part Code 0105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0105 58626 An XP Snapshot pair is defined. Cancel the pair definition, and then retry the operation. Cancel the pair definition, E and then retry the operation. 6 0105 58710 The specified volumes include remote command devices registered in the extended consistency group of Universal Replicator for Mainframe.
Table 10 Error Codes — Part Code 0110 (continued) 52 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0110 5510 The array is refreshing, or another user is changing the array's configuration. Try again later. The array is refreshing, or some other user is changing configuration. Log on again after a while. N 3 0110 5829 Modify mode has already been released. Change to Modify mode, again.
Table 10 Error Codes — Part Code 0110 (continued) Part Code Error Number Error Message 0110 9105 0110 Recommended Action Severity Level Failure Level The value that is under setup To close the window, click is not reflected yet. Do you [OK]. To not close the want to exit? window, click [Cancel]. i 0 9106 The value that is under setup To change the mode, click is not reflected yet. Do you [OK]. To not change the want to change the mode? mode, click [Cancel].
Table 10 Error Codes — Part Code 0110 (continued) Part Code Error Number Error Message 0110 59002 0110 Recommended Action Severity Level Failure Level The storage system is in Wait for a while, and then internal process, or some click [OK] and change the other user is changing the mode to Modify. configuration. Wait for a while, and then click [OK] and change the mode to Modify. Do you want to retry the operation to change the mode to Modify? W 0 59003 Succeeded to change the mode to Modify.
Table 11 Error Codes — Part Code 0190 (continued) Part Code Error Number Error Message Recommended Action Severity Level 0190 5007 Enter the location name. Input the location name and retry. 0190 5008 You cannot use the following Remove the invalid characters characters: " \ , ; : * ? < > and retry. |/ 0190 5009 You cannot use multi-byte characters. Remove the multi-byte characters and retry. 0190 5010 This page can be accessed by the administrator only. None.
Table 11 Error Codes — Part Code 0190 (continued) 56 Part Code Error Number Error Message Recommended Action 0190 5200 Security-file for download does not exist. Call HP technical support. 0190 5210 The number of storage devices exceeds the maximum. You cannot register anymore. 0190 5280 The Remote Web Console has already started. Exit Remote Web Console first, and then restart Remote Web Console. 0190 6001 Failed to open the storage list If the same error occurs again file.
Table 11 Error Codes — Part Code 0190 (continued) Part Code Error Number Error Message Recommended Action 0190 9001 Are you sure you want to delete the selected storage device entry? None. 0190 9100 Are you sure you want to compress files? Reply to this message. 0190 57004 Specify both the certificate file and the key file. Specify both the certificate file and the key file, and then retry the operation. 0190 59304 Are you sure you want to change the setting? Reply to this message.
Table 12 Error Codes — Part Code 0210 (continued) 58 Part Code Error Number Error Message 0210 55618 0210 Recommended Action Severity Level Failure Level Authority of all administrator Check the settings. roles cannot be set to Disable. W 5 55619 Authority of the account administrator role will be lost. Do you want to continue the operation? W 1 0210 55621 Save the setting by using the Click [OK]. setting backup function because you may need to set the Remote Web Console again.
Table 12 Error Codes — Part Code 0210 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0210 65637 Are you sure you want to disable the specified user? To disable the specified user, E click [OK]. Otherwise, click [Cancel]. 5 0210 65638 Are you sure you want to enable the specified user? To enable the specified user, E click [OK]. Otherwise, click [Cancel].
Table 13 Error Codes — Part Code 0290 (continued) 60 Part Code Error Number Error Message Recommended Action 0290 5103 Select [NO] for the Polling Check the settings. period for checking obstacles Option. 0290 5104 Status Window Hidden Option is specified. Select [No]. 0290 6010 The user account list was Reopen. modified by the administrator while you were making settings. 0290 6020 The user ID was deleted by the administrator. Terminate the process.
Table 13 Error Codes — Part Code 0290 (continued) Part Code Error Number Error Message Recommended Action Severity Level 0290 6170 Failed to open the user account list file. If the same error occurs again despite retrying, call HP technical support. 0290 6180 Failed to open the user account list file. If the same error occurs again despite retrying, call HP technical support. 0290 6190 Failed to open the environment file.
Table 13 Error Codes — Part Code 0290 (continued) 62 Part Code Error Number Error Message Recommended Action 0290 9001 Are you sure you want to None. delete the selected user entry? 0290 9002 Are you sure you want to register the parameters? 0290 9003 Are you sure you want to None. change the write permission? 0290 9004 Are you sure you want to change the password? None. 0290 9005 Are you sure you want to restore these files? Reply to this message.
Table 13 Error Codes — Part Code 0290 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0290 56343 The size of the user account list file is too large. Check the size of the file, decrease the size, and retry the operation. 0290 56344 The size of the environment file is too large. Check the size of the file, decrease the size, and retry the operation. 0290 56345 The size of the file is too large.
Table 14 Error Codes — Part Code 0305 64 Part Code Error Number Error Message 0305 6001 0305 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 7060 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 14 Error Codes — Part Code 0305 (continued) Part Code Error Number Error Message 0305 7209 0305 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 7210 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 15 Error Codes — Part Code 0310 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0310 65685 0 cannot be specified in all the fields. Correct the settings, and then W retry the operation. 5 0310 65686 The OS being used does not Correct the settings, and then W support Ipv6. retry the operation. 5 0310 65687 Specify a value between 0 to Correct the settings, and then W 256 in each field for IPv4. retry the operation.
Table 16 Error Codes — Part Code 0405 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0405 5073 To install/uninstall this program product, you must install/uninstall another program product first. Install or remove the related program product first.
Table 16 Error Codes — Part Code 0405 (continued) Part Code Error Number Error Message Recommended Action 0405 5077 To uninstall this program product, you must uninstall another program product first. To uninstall this program W product, you should uninstall another program product first. 5 To uninstall this program W product, you should uninstall another program product first.
Table 16 Error Codes — Part Code 0405 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level ----------------------------------------------------TrueCopy TrueCopy for Asynchronous Mainframe for Mainframe Universal TrueCopy for Replicator for Mainframe Mainframe XP XP Continuous Continuous Access Access Asynchronous XP Continuous Access Journal XP Continuous Access XP External Storage Access Manager XP Continuous Access XP Snapshot Business Copy Performan
Table 16 Error Codes — Part Code 0405 (continued) 70 Part Code Error Number Error Message Recommended Action 0405 5503 You have attempted to install an Emergency key to the option for which a Permanent key has been installed. To install the Emergency key forcibly by using the license key file, specify Only Normal & Warning and retry this operation. To install the Emergency key forcibly by using the license key code, select [OK].
Table 16 Error Codes — Part Code 0405 (continued) Part Code Error Number Error Message 0405 7064 0405 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 7101 The program product has already been installed. W 5 0405 7111 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support.
Table 16 Error Codes — Part Code 0405 (continued) 72 Part Code Error Number Error Message Recommended Action 0405 8003 The subsystem status is invalid. Call HP technical support. Isolate the abnormal section E following the procedure below: 1. Rebooting the computer. If this does not fix the problem: 2. Checking the LAN card/LAN cable. If this does not fix the problem: 3. Checking the IP address of the computer. If this does not fix the problem: 4. Replacing the computer.
Table 16 Error Codes — Part Code 0405 (continued) Part Code Error Number Error Message 0405 56509 0405 Recommended Action Severity Level Failure Level The permanent key cannot be Obtain the block license used after the license is again. changed to the block license. E 5 56524 This function cannot be used Select another window. To by the storage partition set this function, contact the administrator. storage administrator.
Table 16 Error Codes — Part Code 0405 (continued) Part Code Error Number Error Message 0405 65091 0405 66018 Recommended Action Severity Level Failure Level The licensed capacity is Add the licensed capacity. insufficient. The program product is installed but it will be invalid unless you add the licensed capacity during the valid period. W 5 The program product has Purchase the license of the been uninstalled because the program product to use it Term license has expired. continuously.
Table 18 Error Codes — Part Code 0410 (continued) Part Code Error Number Error Message Recommended Action Severity Level 0410 55002 A file name is invalid due to Check the file name and retry W one of the following reasons: the operation. Failure Level 0 • The file name is not specified. • The file name consists of more than 200 characters. • The file name includes an inappropriate character. 0410 55232 Setting capacity exceeded the remaining permitted capacity.
Table 18 Error Codes — Part Code 0410 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0410 59307 Do you want to discard the change and restore the setting? Click [OK] to restore the setting. i 5 0410 59317 The setting of the program product has been changed. Be sure to back up the configuration information. Click [OK].
Table 19 Error Codes — Part Code 0505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0505 6502 A time-out error occurred. Wait for a while, and then retry the operation. If this problem persists, call HP technical support. Wait a few seconds, and retry the operation. W 6 0505 6506 Communication busy. Retry later. Wait a few seconds, and retry the operation.
Table 19 Error Codes — Part Code 0505 (continued) Part Code Error Number Error Message Recommended Action 0505 8401 The status of the storage system requires maintenance (for example, the subsystem is blocked, the shared memory is inconsistent, or some other problem occurs). Check the status of the disk W storage system (for example, the storage system is blocked, the shared memory is inconsistent, or some other problem occurs). If this problem persists, call HP technical support.
Table 22 Error Codes — Part Code 0605 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0605 2011 The status of the storage system requires the maintenance (for example, the subsystem is blocked, the shared memory is inconsistent, or some other factor). Call HP technical support. Check the status of the disk W storage system (if the storage system is blocked, inconsistency of shared memory, or some other factor).
Table 22 Error Codes — Part Code 0605 (continued) Part Code Error Number Error Message Recommended Action 0605 2200 The Concurrent Copy or the Compatible XRC operation is in progress in the target volumes. If the Concurrent Copy or the W Compatible XRC operation is in progress in the target volumes, cancel the Cancel the Concurrent Copy Concurrent Copy job or job or delete a Compatible delete a Compatible XRC pair via the host. If the XRC pair via the host.
Table 22 Error Codes — Part Code 0605 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0605 2516 One of the following is Cancel or suspend the pair defined: a XP Continuous definition, and then retry the Access pair, a XP Continuous operation. Access Journal pair, or a Universal Replicator for Mainframe pair. Please delete the pair definition or suspend the pair, and then retry the operation.
Table 22 Error Codes — Part Code 0605 (continued) 82 Part Code Error Number Error Message 0605 5099 0605 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 5511 The program product is not installed. W 5 0605 5827 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support.
Table 22 Error Codes — Part Code 0605 (continued) Part Code Error Number Error Message 0605 8000 0605 Recommended Action Severity Level Failure Level An error occurred during SVP Retry the operation. If this processing. If this problem problem persists, call HP persists, call HP technical technical support. support. E 3 8001 An error occurred during SVP Retry the operation. If this processing. If this problem problem persists, call HP persists, call HP technical technical support. support.
Table 22 Error Codes — Part Code 0605 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0605 8955 An error occurred on the DKC side. If this problem persists, call HP technical support. An error occurred on the DKC side. If this problem persists, call HP technical support. E 3 0605 8956 An error occurred on the DKC side. If this problem persists, call HP technical support. An error occurred on the DKC side.
Table 22 Error Codes — Part Code 0605 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0605 8967 An error occurred on the DKC side. If this problem persists, call HP technical support. An error occurred on the DKC side. If this problem persists, call HP technical support. E 3 0605 8968 An error occurred on the DKC side. If this problem persists, call HP technical support. An error occurred on the DKC side.
Table 22 Error Codes — Part Code 0605 (continued) Part Code Error Number Error Message Recommended Action Severity Level 0605 56507 The licensed capacity for a program product will become insufficient because of a configuration change. The licensed capacity for a E program product will become insufficient because of a configuration change. Add licensed capacity from the License Key window. Add licensed capacity from the License Key window.
Table 22 Error Codes — Part Code 0605 (continued) Part Code Error Number Error Message Recommended Action 0605 56519 The reserved volume setting of Business Copy, ShadowImage for Mainframe or Compatible FlashCopy(R) is defined. Release the reserved volume setting of Business Copy, ShadowImage for Mainframe or Compatible FlashCopy(R), and then retry the operation. Release the reserved volume E setting of XP Business Copy, ShadowImage for Mainframe or FlashCopy Mirroring, and then retry the operation.
Table 22 Error Codes — Part Code 0605 (continued) 88 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0605 58332 The external volume is blocked. Ensure that the external volume is not blocked, and then retry the operation. E 5 0605 58406 The Delete Volume operation cannot be performed to the volume being used by XP Continuous Access Journal or Universal Replicator for Mainframe.
Table 22 Error Codes — Part Code 0605 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0605 58623 The specified operation cannot be performed, because the XP Snapshot pair using the pool volumes to be maintained is in PSUS status or being restored. Resynchronize or release the E pair definition of the XP Snapshot pair using the pool volume to be maintained, and then retry the operation. 5 Cancel the pair definition, E and then retry the operation.
Table 22 Error Codes — Part Code 0605 (continued) 90 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0605 65801 There are no setting lines of the ExG. Check the contents of the spreadsheet. E 5 0605 65802 There are no setting lines of TargetPathGroup. Check the contents of the spreadsheet. E 5 0605 66004 The description of the operation tag is invalid. Check the contents of the spreadsheet.
Table 22 Error Codes — Part Code 0605 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0605 66508 The size of the defined volume is invalid. Check the contents of the spreadsheet. E 5 0605 66509 The total of the volume size defined in the external volume exceeds the external volume size. Check the contents of the spreadsheet. E 5 0605 66510 The emulation type defined in the volume cannot be used. Check the contents of the spreadsheet.
Table 22 Error Codes — Part Code 0605 (continued) 92 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0605 66696 The number of digits of PathMode is invalid. Check the contents of the spreadsheet. E 5 0605 66697 The value entered as PathMode is outside the setting range. Check the contents of the spreadsheet. E 5 0605 66698 The number of alternate Path Check the contents of the definitions that can be set to spreadsheet.
Table 22 Error Codes — Part Code 0605 (continued) Part Code Error Number Error Message 0605 66716 0605 Recommended Action Severity Level Failure Level The number of digits of CLPR Check the contents of the is invalid. spreadsheet. E 5 66717 The format of CLPR is invalid. Check the contents of the spreadsheet. E 5 0605 66718 The value entered as CLPR is Check the contents of the outside the setting range. spreadsheet. E 5 0605 66719 The number of digits of Emulation is invalid.
Table 22 Error Codes — Part Code 0605 (continued) 94 Part Code Error Number Error Message 0605 66746 0605 Recommended Action Severity Level Failure Level The format of SSID is invalid. Check the contents of the spreadsheet. E 5 66747 The value entered as SSID is outside the setting range. Check the contents of the spreadsheet. E 5 0605 66797 There is an error in the lower Check the contents of the level of the hierarchized spreadsheet. parameter.
Table 22 Error Codes — Part Code 0605 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0605 68741 The Disconnect Subsystem command or the Disconnect Volume command cannot be executed for an external volume that includes pool volumes registered in the Pool that has the association with a normal XP Thin Provisioning volume. Change the status of the associated XP Thin Provisioning volume to Blockade, and then retry the operation.
Table 22 Error Codes — Part Code 0605 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0605 68871 The specified volumes include remote command devices being used with mirrors in the journal group of XP Continuous Access Journal or the Universal Replicator for Mainframe. Release the allocation of mirrors in the journal group for the remote command device. Release the allocation of mirrors in the journal group for the remote command device.
Table 23 Error Codes — Part Code 0610 (continued) Part Code Error Number Error Message Recommended Action Severity Level 0610 9060 Are you sure you want to delete the selected row? To continue processing, click W [OK]. To stop processing, click [Cancel]. 0 0610 9130 The available numerical values for the ExG range from 1 to 16,384. Enter the numerical value to ExG again. i 0 0610 9131 It takes time to execute the request.
Table 23 Error Codes — Part Code 0610 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0610 59034 The processing of this To continue processing, click W command takes some time to [OK]. To stop processing, complete. Do you still want click [Cancel]. to execute the command? After you execute the command, click [Refresh] on the File menu to check the progress. 0 0610 59037 The number of paths registered to a port has reached the maximum.
Table 23 Error Codes — Part Code 0610 (continued) Part Code Error Number Error Message Recommended Action Severity Level 0610 59061 Failed to have the number of Specify fewer alternate paths, i paths the same as the number and then retry the operation. of the specified alternate paths. 0 0610 59062 Failed to assign a normal path. i 0 0610 59063 The number of paths Define a path from a new i registered in the port reached port to the external volume, the maximum. and then retry the operation.
Table 23 Error Codes — Part Code 0610 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0610 69008 An emulation type cannot be Set the emulation type that applied is specified. can be applied in the Set External Volume Parameter dialog box or Edit Policy dialog box. W 0 0610 69009 External volume that can be added was not detected by the search of Volume Discovery.
Table 23 Error Codes — Part Code 0610 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0610 69027 A CLPR number cannot be applied for [Set External Volume Parameter] dialog box or [Edit Policy] dialog box is specified. Specify the CLPR number that E can be applied for [Set External Volume Parameter] dialog box or [Edit Policy] dialog box and retry the operation.
Table 26 Error Codes — Part Code 1005 Part Code Error Number Error Message Recommended Action 1005 1002 The specified volume cannot Select another volume. be set as a command device or a component of a LUSE volume, because it is being used as the volume of XP Continuous Access, Business Copy, Auto LUN, or XP Snapshot. Severity Level Failure Level E 6 Please select another volume.
Table 26 Error Codes — Part Code 1005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 1005 1011 An error occurred. If this problem persists, call HP technical support. The volume that links as an E expanded LU extend over CU#. The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact HP technical support. 2 1005 1012 LU path is set to a volume which links as an expanded LU.
Table 26 Error Codes — Part Code 1005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 1005 1021 An error occurred. If this problem persists, call HP technical support. The specified volume does not E exist. (You have specified wrong CU#:LDEV#.) Or the LDEV (exclusively for mainframe) cannot be processed in this agent. The error does not occur normally because it is guarded in the screen.
Table 26 Error Codes — Part Code 1005 (continued) Part Code Error Number Error Message Recommended Action Severity Level 1005 1050 The following volumes cannot be specified when you change expanded LU configurations: The configuration information E has been already changed. Failure Level 6 Check the settings, and request the setting of the • Volumes reserved by Auto configuration information again. LUN 1005 1059 An error occurred. If this problem persists, call HP technical support.
Table 26 Error Codes — Part Code 1005 (continued) Part Code Error Number Error Message Recommended Action 1005 1108 The following volumes cannot Check the setting, and then be specified when you retry the operation. change the command device configurations: Severity Level Failure Level E 6 • Volumes reserved by Auto LUN • Volumes other than the open-system volumes (including unmounted volumes) • System Disk volume 1005 1110 An error occurred. If this problem persists, call HP technical support.
Table 26 Error Codes — Part Code 1005 (continued) Part Code Error Number Error Message Recommended Action 1005 1127 An error occurred. If this problem persists, call HP technical support. CHA high-speed mode is E specified to unmounted CHA. The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact HP technical support. 2 1005 1128 An error occurred. If this problem persists, call HP technical support.
Table 26 Error Codes — Part Code 1005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 1005 1135 An error occurred. If this problem persists, call HP technical support. When PORT information E (Fibre Address/Fibre Topology/Channel Speed) is set, multiple change instructions are set to the same PORT. The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact HP technical support.
Table 26 Error Codes — Part Code 1005 (continued) Part Code Error Number Error Message Recommended Action 1005 1182 An error occurred. If this problem persists call HP technical support. If this problem persists call HP E technical support. 2 1005 1183 The port information is inconsistent with PCB mode information. Correct the port information W or the PCB mode information. 0 1005 1184 The port information is inconsistent with PCB mode information.
Table 26 Error Codes — Part Code 1005 (continued) Part Code Error Number Error Message Recommended Action 1005 1203 High Speed mode/MIX mode was specified. However, there are addresses to which High Speed mode/MIX mode cannot be set in the Fibre Addresses of the specified ports. The configuration information E has been already changed. High Speed mode/MIX mode was specified. However, there are topologies to which High Speed mode/MIX mode cannot be set in the topologies of the specified ports.
Table 26 Error Codes — Part Code 1005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 1005 1357 S-VOLs remain on the Fibre-RCU port. This operation may cause a fatal damage to the S-VOLs. Please stop this operation. If you want to continue this operation, please remove the S-VOLs from the RCU port first. The specified port is for Fibre E XP Continuous Access. Delete a logical path, and then retry the operation.
Table 26 Error Codes — Part Code 1005 (continued) 112 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 1005 1906 The specified volume cannot Select another volume. be set as a command device because it is being used as a V-VOL for XP Snapshot. E 6 1005 1912 The specified volume is a Correct the settings, and then E remote command device, and retry the operation.
Table 26 Error Codes — Part Code 1005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 1005 2032 Communication busy. Retry later. Retry the operation later. E 3 1005 2082 Processing is disabled because the host is mounted or the device is reserved. The host is mounted or the device is reserved. Unmount the host and cancel reservation of the device. If the host is an AIX host, unmount the host, and execute the varyoffvg command.
Table 26 Error Codes — Part Code 1005 (continued) Part Code Error Number Error Message Recommended Action 1005 2504 No settings can be made Release the reserved attribute W because of a volume reserved of the target volume by using for RAID Manager. Data Retention Utility. 5 1005 3002 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 26 Error Codes — Part Code 1005 (continued) Part Code Error Number Error Message 1005 6040 1005 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 6050 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 26 Error Codes — Part Code 1005 (continued) Part Code Error Number Error Message 1005 55571 1005 1005 Recommended Action Severity Level Failure Level The target cannot be set Check the setting. because the number of targets exceeds the maximum that can be set in a port. E 6 55574 The setting of the specified port cannot be changed because the attribute of the specified port is Initiator or External. E 6 56301 An error occurred during SVP If this problem persists, call processing.
Table 26 Error Codes — Part Code 1005 (continued) Part Code Error Number Error Message Recommended Action Severity Level 1005 65660 The XP Thin Provisioning volume is not associated with a pool. Associate the XP Thin Provisioning and a pool first. Associate the XP Thin E Provisioning volume with the same pool, and then retry the operation. 1005 65672 XP Thin Provisioning Select another volume. volume(s) cannot be combined into LUSE volumes.
Table 27 Error Codes — Part Code 1010 (continued) 118 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 1010 5053 No port is specified. Check the content of the operation. W 5 1010 5054 You must map at least one Check the content of the path to the command device. operation. W 5 1010 5056 The specified LUN does not exist in the system. Check the content of the operation. W 5 1010 5057 No LUN is specified. Check the content of the operation.
Table 27 Error Codes — Part Code 1010 (continued) Part Code Error Number Error Message Recommended Action 1010 9017 LUN security will be applied to the specified command device. Do you want to continue? To continue processing, click i [OK]. Otherwise, click [Cancel]. 0 1010 9019 The LUN will not be specified as a command device. Also, command device security will be disabled on the LUN. Do you want to continue? i 0 1010 9103 Do you want to change? i 0 1010 9150 Select the free LUN.
Table 28 Error Codes — Part Code 1110 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 1110 1064 The specified host is already in use. Correct the specified contents, and request the setting of the configuration information again. W 5 1110 1065 The specified name is already Correct the specified in use. contents, and request the setting of the configuration information again.
Table 28 Error Codes — Part Code 1110 (continued) Part Code Error Number Error Message 1110 5050 The system cannot drop the host onto the port. 1110 5051 The system cannot drop the host to the root. 1110 5052 The system cannot move the host. Specified host already exists in the destination. 1110 Recommended Action Severity Level Failure Level W 5 Check the content of the operation. W 5 Check the content of the operation.
Table 28 Error Codes — Part Code 1110 (continued) 122 Part Code Error Number Error Message 1110 9010 1110 Recommended Action Severity Level Failure Level All the hosts connected to the target port can access only the LUNs defined in group #00. Therefore, the file system may become corrupt while the LUNs defined in all other groups are inaccessible. Are you sure you want to continue this operation? i 0 9011 Only the host registered in the group can access the LUNs defined to the group.
Table 28 Error Codes — Part Code 1110 (continued) Part Code Error Number Error Message 1110 9100 1110 Recommended Action Severity Level Failure Level There are different security settings in the group. Do you want to re-configure? i 0 9101 There are some WWN To execute the operation in groups or LUN groups that Preview, click [OK]. don't have enough members.
Table 28 Error Codes — Part Code 1110 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 1110 59336 The host is to be moved. Do you want to continue? To continue processing, click W [OK]. To stop processing, click [Cancel]. 1110 65751 You cannot use the following Remove the prohibited characters for the UUID: \ / characters from the UUID. , : ; * " < > | You cannot use spaces for the first and the last characters in the UUID.
Table 29 Error Codes — Part Code 1205 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 1205 58387 A communication error If the same problem persists W occurred while executing the despite retrying, check the contents of the setting. LAN setting between the SVP and the disk storage system. If this problem persists, call HP technical support. (Obtain trace information by using the FD Dump tool.) 5 1205 58389 The specified function is not supported.
Table 30 Error Codes — Part Code 1305 (continued) Part Code Error Number Error Message 1305 66575 1305 Recommended Action Severity Level Failure Level Serial number tag exists in Check the contents of the the spreadsheet. However, spreadsheet. the serial number is not set or the destination serial number is different. E 5 66576 The operation tag is not defined. Check the contents of the spreadsheet.
Table 31 Error Codes — Part Code 1310 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 1310 69047 The specified command is not See the user guide. supported. E 5 1310 69048 The operation cannot be executed because the authority of Storage Administrator Role is not “Enable”. Display the account window E of the Remote Web Console, and then set the Storage Administrator Role authority of the user who executes this operation to Enable.
Table 32 Error Codes — Part Code 2005 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 2005 1002 The specified volume cannot Select another volume. be set as a command device or a component of a LUSE volume, because it is being used as the volume of XP Continuous Access, Business Copy, Auto LUN, or XP Snapshot. E 6 E 6 The configuration information E has been already changed. 6 Please select another volume.
Table 32 Error Codes — Part Code 2005 (continued) Part Code Error Number Error Message Recommended Action 2005 1028 The number of volumes you intend to combine into a LUSE volume exceeds the maximum. The configuration information E has been already changed. 2005 1050 Severity Level Failure Level 6 Check the settings, and request the setting of the configuration information again. The following volumes cannot Check the settings, and then be specified when you retry the operation.
Table 32 Error Codes — Part Code 2005 (continued) Part Code Error Number Error Message Recommended Action 2005 1365 The different drive types Retry the operation after you E cannot be combined to form make sure the different drive a LUSE volume. types (FC drive, SATA drive, and SSD) are not coexisting. 6 2005 1599 This functionality is not available. Open Volume Management or LUN Manager is required. Install the necessary program E product.
Table 32 Error Codes — Part Code 2005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 2005 2015 An error occurred while connecting to the subsystem. Wait for a while, and then retry the operation. A communication error occurs. If the error occurs after retrying, call HP technical support. E 6 2005 2032 Communication busy. Retry later. Retry the operation later.
Table 32 Error Codes — Part Code 2005 (continued) 132 Part Code Error Number Error Message 2005 5013 2005 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 6 6012 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 33 Error Codes — Part Code 2010 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 2010 5030 The LUSE volume cannot be Correct the settings, and then W released because the access retry. attribute of the specified volume is not Read/Write. 5 2010 5031 Select the non-LUSE LDEV. Correct the specified content, W and retry. 5 2010 5032 There are no LDEVs available Correct the specified content, W to set the LUSE top volume. and retry.
Table 33 Error Codes — Part Code 2010 (continued) Part Code Error Number Error Message 2010 9151 2010 Recommended Action Severity Level Failure Level Select the LUSE volume. i 0 9152 Warning: It is required to assign the LU Path for the LUSE volume. Do you want to continue? i 0 2010 9153 Select the first LDEV of the LUSE volume. i 0 2010 9355 The specified volumes will be To continue processing, click i expanded to LUSE volume. [OK].
Table 34 Error Codes — Part Code 3005 (continued) Part Code Error Number Error Message 3005 2085 3005 Recommended Action Severity Level Failure Level Copying is in progress for XP Wait for a while and then Continuous Access, Business retry. Copy, ShadowImage for Mainframe, Auto LUN, or Compatible FlashCopy(R) pairs. Please wait for a while and then retry.
Table 34 Error Codes — Part Code 3005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3005 2094 Some Business Copy, ShadowImage for Mainframe, or Compatible FlashCopy(R) pairs exist. Please change the status of their volumes to Simplex. Some XP Business Copy, W ShadowImage for Mainframe, or FlashCopy Mirroring pairs exist. Change the status of their volumes to Simplex. 6 3005 2095 A maintenance operation is in progress.
Table 34 Error Codes — Part Code 3005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3005 2204 Devices to be maintained include journal volumes. Delete or suspend all pairs belonging to journal volumes to be maintained. Devices to be maintained E include journal volumes. Delete or suspend all pairs belonging to journal volumes to be maintained. 6 3005 2205 Devices to be maintained Devices to be maintained E include journal volumes.
Table 34 Error Codes — Part Code 3005 (continued) 138 Part Code Error Number Error Message Recommended Action Severity Level 3005 2518 One of the following is defined: a Business Copy pair, a ShadowImage for Mainframe pair, or a Compatible FlashCopy(R) pair. Split the pair, and then retry the operation. If a reserve volume is defined, cancel the reservation. If the Quick Split mode is on, suspend the pair, and then split. Split the pair, and then retry E the operation.
Table 34 Error Codes — Part Code 3005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3005 5874 The program product required for using the shredding function is not installed. Install the required program product. E 6 3005 5875 The specified volume is formatting or shredding. Retry the operation later. E 6 3005 6000 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support.
Table 34 Error Codes — Part Code 3005 (continued) Part Code Error Number Error Message 3005 8000 3005 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 8001 A communication time-out error occurred in the disk subsystem. Please wait for a while, and then retry the operation. If this problem persists, call HP technical support.
Table 34 Error Codes — Part Code 3005 (continued) Part Code Error Number Error Message Recommended Action 3005 55509 An error occurred during SVP If this problem persists, call processing. HP technical support. Severity Level Failure Level E 2 E 2 E 2 E 2 E 2 E 2 If this problem persists, call HP technical support. 3005 55510 An error occurred during SVP If this problem persists, call processing. HP technical support. If this problem persists, call HP technical support.
Table 34 Error Codes — Part Code 3005 (continued) Part Code Error Number Error Message Recommended Action 3005 56303 An error occurred during SVP If this problem persists, call processing. HP technical support. Severity Level Failure Level E 2 If this problem persists, call HP technical support. 3005 56524 This function cannot be used Select another window. To by the storage partition set this function, contact the administrator. storage administrator.
Table 34 Error Codes — Part Code 3005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3005 58466 The specified logical volume cannot be registered, because an SCSI path is set to the logical volume. Specify another logical volume. E 6 3005 58467 The specified volume cannot be set as a Pool-VOL, because it exceeds the licensed capacity. The current licensed capacity E is insufficient. Purchase a new license key to increase the licensed capacity.
Table 34 Error Codes — Part Code 3005 (continued) Part Code Error Number Error Message Recommended Action Severity Level 3005 58570 V-VOL management area is being used. Delete the XP Snapshot pairs, E and then retry the operation. Failure Level 6 Delete the XP Snapshot pair(s), and then retry the operation. 3005 58571 The specified operation Check the pool-VOL setting. cannot be executed because the Pool-VOL is not mounted.
Table 34 Error Codes — Part Code 3005 (continued) Part Code Error Number Error Message 3005 65650 3005 Recommended Action Severity Level Failure Level The specified volume is used Check the setting of the as a System Disk volume. specified volume. E 6 65659 The specified volume is used Check the setting of the as an XP Thin Provisioning specified volume. volume. E 6 3005 65671 The pool volumes associated with the XP Thin Provisioning volume is included in the items to be maintained.
Table 34 Error Codes — Part Code 3005 (continued) 146 Part Code Error Number Error Message Recommended Action 3005 65692 The specified volumes contain Select only the volumes that E volumes that quick format quick format can be executed cannot be executed. Select and execute quick format. only the volumes that quick format can be executed and execute quick format. 6 3005 65693 Quick format cannot be executed.
Table 34 Error Codes — Part Code 3005 (continued) Part Code Error Number Error Message 3005 68726 3005 Recommended Action Severity Level Failure Level The capacity of XP Thin Check volume capacity for Provisioning volume (TP-VOL) the TP-VOL. is insufficient. E 6 68727 Shared memory is being initialized. Wait a few seconds, and then retry the operation. Wait a few seconds, and then retry the operation. E 6 3005 68728 The pool is in an abnormal state.
Table 34 Error Codes — Part Code 3005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3005 68797 Restoration of the pool has failed. Pool cannot be restored when: When the pool cannot be restored, do the following: E 6 E 6 • processing takes time, because blocked parts exist in the storage system. • the Pool-VOL is blocked.
Table 34 Error Codes — Part Code 3005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3005 68799 Failed to change the threshold of the pool. The threshold of the pool cannot be changed when: When the pool threshold cannot be changed, do the following: E 6 • the threshold is set below the usage rate of the pool. • Update the display content and confirm the usage rate of the pool.
Table 34 Error Codes — Part Code 3005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3005 68824 The specified volume is currently used by XP Continuous Access or XP External Storage Access Manager. Wait until the process of XP Continuous Access or XP External Storage Access Manager is completed, and then retry the operation.
Table 35 Error Codes — Part Code 3010 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3010 1046 The number of Cache Residency Manager settings has exceeded the maximum number of available Cache Residency Manager areas. Reduce the number of Cache W Residency Manager settings, and then retry the operation. 5 3010 5010 The specified SSID falls out of range. Specify a valid SSID, and then retry the operation. Correct the specified content, W and retry.
Table 35 Error Codes — Part Code 3010 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3010 5054 Execute any of the corresponding items below before deleting LDEV: Check the content of the operation. W 5 Check the content of the operation. W 5 However, LDEV cannot be deleted when it is a remote command device. • delete the paths associated with the LDEV. • release the LUSE volume. • release the reserved volume of Auto LUN.
Table 35 Error Codes — Part Code 3010 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3010 5058 Volume Initialize cannot be performed because the number of volumes that can be created in the parity group is exceeded. Reduce the number of volumes in the parity group, and then retry. W 5 3010 5060 The setting capacity in the VLL Enter the correct value. operation is outside the setting range. Set the capacity within the specified range.
Table 35 Error Codes — Part Code 3010 (continued) Part Code Error Number Error Message Recommended Action 3010 9001 Custom volume operation has The normal end was carried i completed. out. Click [OK] and close the dialog. 0 3010 9010 Do you want to set the following custom volume? i 0 3010 9011 The specified volume will be initialized. The stored data in the volume will be deleted. Do you want to continue? i 0 3010 9012 The following normal volume will be restored.
Table 35 Error Codes — Part Code 3010 (continued) Part Code Error Number Error Message Recommended Action 3010 55033 There is no specifiable LDEV Click [OK]. number. Probable causes and solutions are: Severity Level Failure Level W 0 W 0 • The CU number that can be specified for the started SLPR is not assigned. Contact the storage administrator. • All LDEVs in the usable CU are already used. • Check whether the LDEVs are used by another SLPR. Alternatively, contact the storage administrator.
Table 35 Error Codes — Part Code 3010 (continued) Part Code Error Number Error Message Recommended Action Severity Level 3010 58209 An error occurred in format processing or in Write to Control Blocks processing. Confirm whether the external E volume is zero formatted when an error occurs in Write to Control Blocks processing. Execute zero format processing when the external volume is not zero formatted. Failure Level 0 Retry the operation if the error occurred in the format processing.
Table 35 Error Codes — Part Code 3010 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3010 65647 Reset operation cannot be Reduce the number of W performed because the volumes in the parity group, number of volumes that can and then retry the operation. be created in the parity group exceeds the maximum. 5 3010 65711 You are trying to execute Quick Format to a volume that does not support Quick Format. Specify another volume or select Format.
Table 35 Error Codes — Part Code 3010 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3010 69045 System Disk becomes an To continue processing, click i inaccessible volume from the OK. To stop processing, click host because of the area used Cancel. in the disk subsystem. Do you want to continue? 5 3010 69061 Do you want to format logical Click [OK] to execute Quick i devices with Quick Format? Format. Click [No] to execute format.
Table 36 Error Codes — Part Code 3110 (continued) Part Code Error Number Error Message Recommended Action Severity Level 3110 55504 Because CLPR numbers of the specified pool volumes, internal volumes/external volumes, cache modes, and the internal volume information coexist, the pool volumes cannot be registered in the pool. If the pool volumes cannot be W registered, do the following: Failure Level 5 • Check if two or more CLPR numbers of the pool volumes exist.
Table 37 Error Codes — Part Code 3205 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3205 2085 Copying is in progress XP Wait a few seconds, and Continuous Access, Business then retry the operation. Copy, ShadowImage for Mainframe, Auto LUN, Compatible FlashCopy(R), or Flex Copy XP pairs. Please wait for a while, and then retry the operation.
Table 37 Error Codes — Part Code 3205 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3205 2201 Processing cannot be performed because of Data Retention settings. Correct settings, and then retry. W 5 3205 3003 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 3205 5013 An error occurred during SVP If this problem persists, call processing.
Table 37 Error Codes — Part Code 3205 (continued) 162 Part Code Error Number Error Message 3205 8000 3205 Recommended Action Severity Level Failure Level An error occurred during SVP Retry the operation. If this processing. If this problem problem persists, call HP persists, call HP technical technical support. support. E 3 8001 An error occurred during SVP Retry the operation. If this processing. If this problem problem persists, call HP persists, call HP technical technical support.
Table 37 Error Codes — Part Code 3205 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3205 8959 An error occurred on the DKC side. If this problem persists, call HP technical support. An error occurred on the DKC side. If this problem persists, call HP technical support. E 3 3205 8960 An error occurred on the DKC side. If this problem persists, call HP technical support. An error occurred on the DKC side.
Table 37 Error Codes — Part Code 3205 (continued) Part Code Error Number Error Message Recommended Action 3205 8971 Failed to update the configuration information. Call HP technical support. Reboot the SVP computer, E and retry the operation. If this problem persists, call HP technical support. 2 3205 8978 An error occurred on the DKC side. If this problem persists, call HP technical support. An error occurred on the DKC side. If this problem persists, call HP technical support.
Table 37 Error Codes — Part Code 3205 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3205 68740 Delete volume operation cannot be performed to the XP Thin Provisioning volume associated with a pool. Release the association with the pool, and then retry the operation. The delete volume operation cannot be performed to the XP Thin Provisioning volume associated with a pool. Release the association with the pool, and then retry the operation.
Table 38 Error Codes — Part Code 3210 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3210 55001 The specified V-VOL group cannot be deleted. Check the specified content, and retry the operation. W 5 A V-VOL group cannot be deleted when it contains the following volumes: • A volume with path definition. • A LUSE volume. 3210 55002 The maximum number of V-VOL Groups is already registered. Check the setting range, and W then retry the operation.
Table 38 Error Codes — Part Code 3210 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3210 59001 Are you sure you want to delete the selected V-VOL group? To continue processing, click i [OK]. Otherwise, click [Cancel]. 5 3210 59201 The V-VOL group information To continue processing, click i is to be set with free setting. [OK]. Otherwise, click [Cancel].
Table 38 Error Codes — Part Code 3210 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3210 65754 The same operation cannot be done, because the discarding zero data is currently being executed. Check the content of the operation. W 5 3210 65755 Cancel operation of the Check the content of the discarding zero data cannot operation. be performed because the system is not executing the zero data discarding. W 5 3210 65766 Set volumes.
Table 38 Error Codes — Part Code 3210 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3210 69057 The emulation type of an XP Thin Provisioning volume (TP-VOL) that is set to OPEN-0V will change to OPEN-V. To continue processing, click W [Normal] or [Force]. To stop processing, click [Cancel]. 5 The emulation type of an XP To continue processing, click W Thin Provisioning volume [Normal] or [Force].
Table 39 Error Codes — Part Code 3305 Part Code Error Number Error Message 3305 1035 3305 1036 Recommended Action Severity Level Failure Level The SSIDs are not defined. If If this problem persists, call this problem persists, call HP HP technical support. technical support. E 2 The size of the specified The size of volume that can volume is outside the setting be set differs by the type of range. emulation.
Table 39 Error Codes — Part Code 3305 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3305 1075 In the VLL operation (Install CV, Make Volume, Volume Initialize and Volume to Space), there are some operations which cannot be set together are specified. The operations that can be set together at a time are Make Volume and Volume Initialize only.
Table 39 Error Codes — Part Code 3305 (continued) Part Code Error Number Error Message Severity Level Failure Level 3305 1913 The setting cannot be made Check the setting. because the specified LDEV is a remote command device. E 6 3305 1914 The number of V-VOL(s) has Correct the settings, and then E exceeded the maximum retry the operation. number of V-VOL(s) that can be set in a storage system. 6 3305 1919 The newly added LDEV has Check the blocked LDEV and W not been formatted.
Table 39 Error Codes — Part Code 3305 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3305 2085 Copying is in progress for XP Continuous Access, Business Copy, ShadowImage for Mainframe, Auto LUN, Compatible FlashCopy(R) pairs. Please wait for a while, and then retry the operation. Wait a few seconds, and then retry the operation.
Table 39 Error Codes — Part Code 3305 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3305 2093 Some Business Copy, ShadowImage for Mainframe, or Compatible FlashCopy(R) pairs exist. Please resynchronize them. Resynchronize some existing XP Business Copy, ShadowImage for Mainframe, or FlashCopy Mirroring pairs. W 6 3305 2094 Some Business Copy, ShadowImage for Mainframe, or Compatible FlashCopy(R) pairs exist.
Table 39 Error Codes — Part Code 3305 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3305 2205 Devices to be maintained Delete all pairs to which the include journal volumes. journal volumes belong. Delete all pairs to which the journal volumes belong. E 6 3305 2515 One of the following is defined: a XP Continuous Access pair, a XP Continuous Access Journal pair, or a Universal Replicator for Mainframe pair.
Table 39 Error Codes — Part Code 3305 (continued) 176 Part Code Error Number Error Message Recommended Action Severity Level 3305 2520 An Auto LUN pair is defined. Release the pair definition, E Release the pair definition and then retry the operation. and then retry the operation. 6 3305 2521 An Auto LUN pair is defined. Release the pair definition. If a reserve volume is defined, cancel the reservation and then retry the operation.
Table 39 Error Codes — Part Code 3305 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3305 6092 An error occurred during SVP processing. If this problem persists, call HP technical support. If this problem persists, call HP technical support. E 2 3305 55500 An error occurred during SVP processing. If this problem persists, call HP technical support. If this problem persists, call HP technical support.
Table 39 Error Codes — Part Code 3305 (continued) 178 Part Code Error Number Error Message Recommended Action 3305 65692 The format processing for the Execute the format processing W added volume has not been for the added volume. executed because the specified volumes contain volumes that quick format cannot be executed Execute the format processing for the added volume.
Table 39 Error Codes — Part Code 3305 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3305 65741 An error occurred during SVP processing. If this problem persists, call HP technical support. If this problem persists, call HP technical support. E 2 3305 65742 An error occurred during SVP processing. If this problem persists, call HP technical support. If this problem persists, call HP technical support.
Table 39 Error Codes — Part Code 3305 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3305 68892 The item to be formatted Restore the pool that has E includes an XP Thin been blocked by the XP Thin Provisioning volume Provisioning function. (TP-VOL). However, the TP-VOL cannot be formatted because there is a pool that has been blocked. Restore the blocked pool first, and then retry the operation.
Table 40 Error Codes — Part Code 4005 (continued) Part Code Error Number Error Message 4005 6040 4005 Severity Level Failure Level An error occurred while If this problem persists, call connecting to the subsystem. HP technical support. Wait for a while, and then retry the operation. E 6 6502 Processing in progress. Please wait for a while, and then retry the operation. W 0 4005 7060 An error occurred during SVP If this problem persists, call processing. HP technical support.
Table 40 Error Codes — Part Code 4005 (continued) Part Code Error Number Error Message Recommended Action 4005 55265 The parity group that contains Check the settings, and then the volume(s) to which Cache retry the operation. Residency is set cannot be migrated to another CLPR. Severity Level Failure Level E 6 Please remove the Cache Residency settings from the volumes, and then migrate the parity group.
Table 40 Error Codes — Part Code 4005 (continued) Part Code Error Number Error Message Recommended Action Severity Level 4005 55540 The specified function is not Install the required program E available because it requires product. When an SLPR is Cache Residency Manager. allocated, install a necessary program product for the SLPR. 6 4005 55541 The specified function is not Install the required program available because it requires product. Cache Residency Manager for Mainframe.
Table 40 Error Codes — Part Code 4005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 4005 58514 Currently running microcode version does not support the specified operation. Call HP technical support. E 2 4005 58709 A maintenance operation is in progress. For example: Wait a few seconds, and then retry the operation.
Table 41 Error Codes — Part Code 4010 (continued) Part Code Error Number Error Message Recommended Action Severity Level 4010 5030 No deletion area is specified. Correct the specified content, W Retry the operation to specify and retry. the deletion area. 5 4010 5058 The Cache Residency settings Correct the Cache Residency W that exceed the maximum settings, and then retry the size or maximum available operation. area are invalid.
Table 42 Error Codes — Part Code 4105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 4105 7060 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 4105 7111 An error occurred during server processing. If this problem persists, call HP technical support. An error occurred during SVP E processing. If this problem persists, call HP technical support.
Table 43 Error Codes — Part Code 5105 Part Code Error Number Error Message 5105 2002 5105 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 2003 An error occurred during SVP processing. If this problem persists, call HP technical support. Use the SVP to check if the DKC is in the normal status, and then retry.
Table 43 Error Codes — Part Code 5105 (continued) Part Code Error Number Error Message 5105 6000 5105 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 6002 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 43 Error Codes — Part Code 5105 (continued) Part Code Error Number Error Message 5105 8916 5105 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 8918 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 44 Error Codes — Part Code 5110 Part Code Error Number Error Message Recommended Action Severity Level 5110 59030 The monitoring data saved at To continue processing, click i present will be deleted. [OK]. Otherwise, click [Cancel]. Failure Level 5 The monitoring data currently saved will be deleted when you change the setting of the monitoring switch. If necessary, use the Export Tool to save the monitoring data.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message 5205 1080 The command was rejected due to one of the following reasons. Recommended Action Severity Level Recover the blocked volume, E and then retry the operation. Also, the system disk cannot • The specified volume was be used as a P-VOL. Specify another volume. blocked. Failure Level 6 • The specified volume was used as a system disk. 5205 1081 The specified volume(s) are used as a command device.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 5205 1117 The volume specified as a migration source is already used as a volume of Concurrent Copy. The specified volume is already used by Concurrent Copy. Specify another volume. E 6 5205 1118 The volume specified as a migration source is already used as a volume of Concurrent Copy. The specified volume is already used by Concurrent Copy.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message 5205 1213 The command was rejected due to one of the following reasons. Recommended Action Severity Level Recover the blocked volume, E and then retry the operation. Also, the system disk cannot • The volume specified as a be used as a P-VOL. Specify another volume. migration source was Failure Level 6 blocked. • The volume specified as a migration source was used as a system disk.
Table 45 Error Codes — Part Code 5205 (continued) 194 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 5205 1223 The volume(s) are already used by Auto LUN. Retry the same operation. If nothing changes, call HP technical support. E 6 5205 1224 The volume(s) are already used by Auto LUN. Retry the same operation. If nothing changes, call HP technical support. E 6 5205 1225 The selected source volume and destination volume are the same volume.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message 5205 1233 5205 Recommended Action Severity Level Failure Level The volume specified as a Specify another volume. migration target cannot be migrated, because it is already used as a volume of ShadowImage for Mainframe, XP Business Copy, or Compatible FlashCopy(R).
Table 45 Error Codes — Part Code 5205 (continued) 196 Part Code Error Number Error Message 5205 1243 5205 Recommended Action Severity Level Failure Level The specified volume is not a Retry the same operation. If source volume. nothing changes, call HP technical support. E 6 1246 The number of plans that could be executed at once exceeds the maximum. Retry the same operation. If nothing changes, call HP technical support. E 6 5205 1247 The volume is already a source volume.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 5205 2029 A data transfer failure was detected. Call HP technical support. E 6 5205 2030 A data transfer failure was detected. Call HP technical support. E 6 5205 2033 The SVP is now updating the statistics data. Wait for a while, and then select the [Refresh] button. The SVP is collecting the W latest data. Internal processing in progress.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message Recommended Action 5205 5506 The specified volume cannot be migrated, because it is used as a P-VOL in either of the following statuses. See the notes in the E Interoperability with Other Products section in the HP StorageWorks • A volume of XP Business XP24000/XP20000 Auto LUN Software User's Guide Copy or TrueCopy for Mainframe in the state of for the relationship between XP Continuous Access, pending.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message Recommended Action Severity Level 5205 6510 The disk subsystem is busy. Please wait for a while, and then retry the operation. Retry the same operation W several times. If the same error occurs, call HP technical support. 5 5205 6511 Check pair status. Check pair status. E 6 5205 6512 Check pair status. Check pair status. E 6 5205 6531 The SVP is busy.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message Recommended Action Severity Level 5205 7407 Cannot make proper migration plan for this function. Retry the same operation E several times. If the same error occurs, call HP technical support. 6 5205 7408 There is not enough valid monitoring data in the specified term. Retry the same operation E several times. If the same error occurs, call HP technical support.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message Recommended Action Severity Level 5205 7420 There is insufficient Auto LUN Retry the same operation E data to create migration several times. If the same plans. Check the following: error occurs, call HP technical support.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message Recommended Action Severity Level 5205 8530 An internal logic error occurred. Check the volume, or quit E using XP Continuous Access. 0 5205 8531 An internal logic error occurred. Check the volume, or quit E using XP Continuous Access. 0 5205 8671 The sizes of the source and the target volumes are not equal.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message Recommended Action Severity Level 5205 55225 The specified plan was not The specified plan cannot be E created with the Remote Web released with Remote Web Console. Console. 6 5205 55226 The specified plan was not The specified plan cannot be E created with the Remote Web released with Remote Web Console. Console. 6 5205 55227 The specified volume is already reserved with a different owner ID by Auto LUN.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 5205 55524 The specified volume(s) are already being used as XP Snapshot volume(s). Select another volume. E 6 5205 55525 The specified volume(s) are already being used as V-VOL(s). Select another volume. E 6 5205 55526 The specified volume(s) are already being used as Pool-VOL(s). Select another volume.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message 5205 55598 5205 Severity Level Failure Level The specified volume is used Check the setting of the as a Delta resync volume for specified volume. XP Continuous Access Journal or Universal Replicator for Mainframe. E 6 55599 The volume specified as a migration target is used as a volume of Delta resync for XP Continuous Access Journal or Universal Replicator for Mainframe.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message 5205 57101 5205 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 57102 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 5205 65699 The specified volume cannot be used because Quick Format is performed on the specified volume. Retry the operation after the quick format is completed. E 6 5205 65700 The volume specified as a migration source cannot be used, because it is being used by FICON(R) Data Migration. Specify another volume.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 5205 65712 The specified plan cannot be migrated, because the plan is a combination of an internal volume of OPEN-V and a XP Thin Provisioning volume of OPEN-0V. See the notes in the Interoperability with Other Products section in the HP StorageWorks XP24000/XP20000 Auto LUN Software User's Guide for the combination of the volumes that cannot be migrated.
Table 45 Error Codes — Part Code 5205 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 5205 65749 The volume specified as a migration source cannot be used, because it is a volume of XP Thin Provisioning in zero data discarding. Retry the operation after the zero data discarding operation has completed.
Table 46 Error Codes — Part Code 5210 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 5210 59071 This migration plan extends across multiple SLPRs. If you perform this operation, the storage partition administrator will become unable to operate. Do you want to continue this operation? To continue processing, click i [OK]. To stop processing, click [Cancel].
Table 47 Error Codes — Part Code 5305 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 5305 2033 The SVP is now updating the Wait a few seconds, and statistics data. Wait for a click [Refresh]. while, and then select the [Refresh] button. W 3 5305 2145 A connection error has occurred. 5305 3003 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 47 Error Codes — Part Code 5305 (continued) 212 Part Code Error Number Error Message 5305 5110 5305 Recommended Action Severity Level Failure Level The number of WWN(s) that Check the specified content, is monitored exceeds the and retry. maximum. W 6 5111 The number of the WWN Check the specified content, exceeds the maximum and retry. number that can be registered on an Performance Control group. W 6 5305 5112 The specified WWN is registered on a Performance Control group.
Table 47 Error Codes — Part Code 5305 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 5305 7428 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 5305 8002 The subsystem status is invalid. Call HP technical support. Retry the same operation E several times. If the same error occurs, call HP technical support.
Table 47 Error Codes — Part Code 5305 (continued) Part Code Error Number Error Message 5305 56524 5305 56525 Recommended Action Severity Level Failure Level This function cannot be used Select another window. To by the storage partition set this function, contact the administrator. storage administrator. E 3 Because the settings across the multiple SLPRs are contained, the authority has been shifted to the storage administrator from the storage partition administrator.
Table 47 Error Codes — Part Code 5305 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 5305 58574 An error occurred while connecting to the subsystem. Wait for a while, and then retry the operation. The error may be caused by a temporary communication failure. Reboot the SVP or click [Refresh All] on the File menu of Remove Web Console and refresh the configuration information to recover from the error.
Table 49 Error Codes — Part Code 5310 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 5310 1110 You cannot use the following Remove the prohibited characters for the name: characters from the nickname. \/,:;*"<>| W 5 Enter a correct value, and retry. W 5 You cannot use spaces for the first and the last characters in the name. 5310 5000 The specified WWN is invalid.
Table 49 Error Codes — Part Code 5310 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 5310 5133 A WWN registered on an Performance Control group cannot be deleted. Delete the WWN from Performance Control Group first. W 5 5310 5134 The attribute of the WWN is Set the attribute together. different from that of the Performance Control group. W 5 5310 5136 This WWN is already registered as a different Nickname. Check the content, and retry.
Table 49 Error Codes — Part Code 5310 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 5310 9329 To continue initialization, select OK on the next window. To quit the operation, select Cancel on the next window. If you click [OK] on the next W window, the settings on port control will be initialized. To quit the operation, click [Cancel] on the next window. 5 5310 9330 To continue initialization, select OK on the next window.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message 6005 6012 6005 Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 6023 The SVP is busy. Please wait If the same problem persists for a while, and then retry the despite retrying, call HP operation. technical support. W 3 6005 8000 A time-out error occurred. Retry the operation.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6005 8704 The specified number of Check the paths status and paths is less than the reestablish the paths. minimum number of paths on the RCU option screen due to a communication error between the MCU and the RCU. W 4 6005 8705 The path could not be deleted Either a communication error W due to a communication error occurred between the MCU between MCU and RCU.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6005 8714 An internal error occurred. Call HP technical support. E 4 6005 8715 Invalid number of paths. The specified number of E paths is not within the acceptable path range of 0 to 4. Verify the number of paths and retry the operation. 4 6005 8717 Invalid Destination Link Address. The specified logical address E must be either 00 or 01.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action 6005 8728 The number of minimum Take either of the following i paths exceeds the number of actions: normal paths. 1. Add normal paths, and then delete the paths. 2. Decrease the number of minimum paths, and then delete the paths. 4 6005 8729 An internal error occurred. E 4 6005 8730 Invalid Logical Addresses are Take either of the following specified. actions: 1.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6005 8739 NVS status of MCU is not active. The MCU NVS status i specified by the host is not active. Set the NVS to on for the MCU, using any attached host, and then retry the operation. 4 6005 8740 NVS status of RCU is not active. The RCU NVS status specified i by the host is not active. Use any attached host to set the NVS to on for the MCU, and then retry the operation.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action 6005 8745 A volume cannot be used as Select another volume. an R-VOL when: Severity Level Failure Level i 4 • it is used by Compatible XRC. • it is used by PPRC or XP Continuous Access. • it is used by Concurrent Copy. • it is in a reserved condition. • it is used by XP Continuous Access Journal or Universal Replicator for Mainframe.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action 6005 8755 The serial number, SSID or CU number of the RCU is invalid. Take either of the following E actions: 1. Check the serial number, SSID or CU number of the RCU, and retry the operation with correct parameters. 2. Check the connection LCP ports of the RCU. Connect the path correctly, and retry the operation. 4 6005 8756 MCU disk array cache is not Check the storage system i active.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action 6005 8766 XP Continuous Access is not supported under the R-VOL Device emulation type. The device emulation type of i the R-VOL does not support XP Continuous Access. Call HP technical support. 6005 8768 The RCU is still in another XP The RCU containing the Continuous Access condition. R-VOL is being used as the RCU for XP Continuous Access.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action 6005 8776 A volume cannot be used as Select another volume. an M-VOL when: Severity Level Failure Level i 4 • it is used by XP Continuous Access Journal or Universal Replicator for Mainframe. • it is used by ShadowImage for Mainframe or Compatible FlashCopy(R). 6005 8777 Combination of MCU with RCU controller type is not supported.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6005 8791 The specified M-VOL is still online from another HOST. Vary the concerned path i offline from the other host, and then retry the operation. 4 6005 8792 Add Pair operation failed because the Volume Retention Manager function is not installed in the specified RCU. Install Volume Retention i Manager in the MCU and the RCU, and then retry the operation.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6005 8796 The operation failed because Check the status of the i the specified R-VOL applied specified R-VOL from the host to any of the following: or the SVP. Failure Level 4 • A T-VOL of ShadowImage for Mainframe or Compatible FlashCopy(R). • An S-VOL of Business Copy. • A reserved volume of ShadowImage for Mainframe or Business Copy.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action 6005 8803 Too many RCUs in this CT Group. The add pair operation failed i because there are too many RCUs in this CT group. If the timer type is None, and then 4 RCU have already been added. If the timer type is Local or System, and then 1 RCU has already been added. Check configuration of CT group numbers already used on both MCU and RCU. Register a new CT group.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6005 8809 Wait. Retry Add Pair (Paircreate)/Resume Pair (Pairresync) operation in a few minutes. Add/resume pair operation failed. The specified volume or another volume in the same group being changed to simplex/suspend status in RCU. After a few minutes, refresh and check the XP Continuous Access window.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6005 8820 The specified R-VOL is not a permissible condition of XP Continuous Access. The XP Continuous Access operation failed, because R-VOL has one of the following conditions: 1. The volume is blocked. 2. The volume is under maintenance. 3. The volume is copying data (correction copy or drive copy) 4. The volume is in the correction access condition.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6005 8832 Wait a few minutes and retry the Add Pair (Paircreate) / Resume Pair (Pairresync) operation. Check the status of the i specified M-VOL (P-VOL), and then retry the Add Pair (Paircreate) / Resume Pair (Pairresync) operation in a few minutes. 4 6005 8833 Wait a few minutes and retry the Add Pair (Paircreate) / Resume Pair (Pairresync) operation.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6005 8843 Suspend(Pairsplit-r) operation failed because specified volume or other volume in the same group is not in permissible status. The operation failed, because i of one of the following reasons: Failure Level 4 • The specified volume is simplex. • There is no duplex or duplex-pending volume in the group.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6005 8852 R-VOL status change failed after M-VOL status change. Confirm R-VOL status. Confirm the R-VOL status. E 4 6005 8854 Delete Pair (Pairsplit-S) operation failed because M-VOL is in Simplex (SMPL) status. The operation failed, because i of one of the following reasons: 4 • The specified volume is simplex.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action 6005 8859 Delete Pair (Pairsplit-S) operation with C/T option failed because some R-VOLs in the group are in Duplex (PAIR) or Pending (COPY) status. The pair status does not allow i this operation. Refresh and confirm the pair status information on the window first. If the R-VOL status is valid, retry the operation. 4 6005 8860 An internal error occurred. Call HP technical support.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6005 8876 There are no PCBs which corresponds to the specified port type. Confirm the PCB type and try i the operation again with a correct parameter. 4 6005 8877 An internal error occurred. Call HP technical support. E 4 6005 8878 CT Group is not active. Verify that the CT group is active in the MCU.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6005 8897 LUs exist on the port. Delete the LUs defined on the E port and retry the operation. 4 6005 8898 Pending data exists on the port. Add another path, or delete all pairs on the RCU. Then retry the operation. i 4 6005 8899 An internal error occurred. Call HP technical support.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6005 8907 The extended SM is not equipped in RCU. Install the extended shared E memory to RCU according to the installation instruction of the extended shared memory for remote copy (Shared Memory Size Configuration dialog box). 5 6005 8908 Invalid parameter. Check the value of the specified parameter, and retry. i 4 6005 8909 A Port exchange error occurred.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6005 8922 The specified MCU does not support serial remote copy connections. Confirm whether the MCU supports serial remote copy connections. Install the microcode of version that supports serial remote copy connections, or use fibre remote copy connections. E 4 6005 8923 The specified RCU does not support serial remote copy connections.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6005 8938 The Paircreate operation with the serial remote copy connection failed because there are pairs with the Fibre Channel remote copy connection in the specified MCU. Delete all the pairs with the Fibre Channel remote copy connection in the specified MCU, and then retry the operation. i 4 6005 8939 The specified M-VOL cannot be used.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message 6005 8973 6005 Recommended Action Severity Level Failure Level The operation failed because Check the status of the the specified R-VOL was used specified R-VOL. for Flex Copy XP. i 4 8975 Failed to create a pair, Check the status of the because the specified R-VOL specified R-VOL. is path-defined from the iSCSI port.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6005 8989 The specified M-VOL is a volume used by FlashCopy Mirroring V2. Check the version of the microcode of the storage system. i 4 The operation failed because If the microcode of the of one of the following storage system supports the reasons.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6005 58320 The operation failed because If the Add Pair (Paircreate) W the specified R-VOL was used operation failed: by XP Continuous Access • When the RCU runs on the Journal or Universal 2DC configuration in Replicator for Mainframe.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action 6005 58452 A pair cannot be created because the licensed capacity of Data Retention Utility on the RCU side is insufficient or Data Retention Utility is not installed on the RCU. Check the licensed capacity i of Data Retention Utility on the RCU side, or confirm whether Data Retention Utility is installed on the RCU.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message 6005 58498 6005 Recommended Action Severity Level Failure Level A pair cannot be created Specify another volume. because the specified M-VOL is being used as a pool volume. i 5 58499 A pair cannot be created because the specified R-VOL is being used as a pool volume. i 5 6005 58509 A communication time-out Wait a few seconds, and error occurred between MCU then retry the operation. and RCU.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6005 58712 The licensed capacity of XP Continuous Access or TrueCopy for Mainframe on the RCU is insufficient. Check the licensed capacity W of this program product and the related program products.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6005 58715 The licensed capacity of XP Continuous Access Asynchronous or TrueCopy Asynchronous for Mainframe on the MCU is insufficient. Check the licensed capacity W of this program product and the related program products.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6005 68757 The Paircreate operation failed because the specified S-VOL, which is an XP Thin Provisioning volume, is already used by another program product. Select another volume that is W not used by other program products such as XP Business Copy, XP Snapshot, and XP Auto LUN, or cancel the use of the volume operated by the other program products and retry the operation.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message 6005 68796 The operation failed. The Refresh the window, and W operation cannot be confirm the pair status of the accepted in the pair status of specified volume. the specified volume. 0 6005 68812 A pair could not be created because the specified R-VOL was an XP Thin Provisioning volume whose capacity was being changed.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6005 68827 The operation failed, because • The serial number of the W there was an error in the local DKC cannot be set specified parameter. as the serial number of the other DKC. Check the input serial number of the other DKC. Failure Level 0 • A quorum disk cannot be registered in a same external storage device with a different quorum disk ID.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6005 68872 The operation failed, because Check the volume setting. the specified volume was not a volume of External Storage. W 0 6005 68873 The operation failed, because Specify another volume, or W the specified volume was release the LU path definition. defined in the LU path.
Table 50 Error Codes — Part Code 6005 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6005 68891 The operation failed, because Confirm the serial numbers of W the following specified the MCU and RCU, and parameters did not match the confirm the quorum disk ID. information in the quorum disk.
Table 51 Error Codes — Part Code 6007 (continued) Part Code Error Number Error Message 6007 6002 6007 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 6012 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 6007 6022 The SVP is busy.
Table 52 Error Codes — Part Code 6010 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6010 5030 The displayed information has not been changed. Specify what you register, and retry. W 0 6010 5034 There are no RCUs in the CU. Correct the specified Try again after registering contents, and retry. RCUs. W 5 6010 5035 There are no CT groups for Register a CT group, and the asynchronous XP retry. Continuous Access.
Table 52 Error Codes — Part Code 6010 (continued) Part Code Error Number Error Message 6010 7303 6010 Recommended Action Severity Level Failure Level An error occurred in the client Call HP technical support. logic. E 2 7440 An error occurred during processing. If this problem persists, call HP technical support. If this problem persists, call HP technical support. E 2 6010 8101 The system cannot apply the new configuration. Do you want to refresh? Click [Refresh], and retry.
Table 52 Error Codes — Part Code 6010 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6010 9070 Are you sure you want to delete the specified RCUs? To delete the specified RCU, click [OK]. Otherwise, click [Cancel]. i 0 6010 9071 Are you sure you want to delete the paths of a specified RCU? To delete the specified path, click [OK]. Otherwise, click [Cancel].
Table 52 Error Codes — Part Code 6010 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6010 9113 Are you sure you want to clear SIMs of XP Continuous Access? To clear the XP Continuous Access related SIM, click [OK]. Otherwise, click [Cancel]. W 0 6010 9114 The value has been changed. To continue the process, click i Do you want to continue the [OK]. Otherwise, click operation? [Cancel].
Table 52 Error Codes — Part Code 6010 (continued) Part Code Error Number Error Message 6010 9129 6010 Recommended Action Severity Level Failure Level Recovered from the error that Click [OK] to continue occurred when copying processing. started. i 0 9154 As a result of this operation, Follow the instructions in the you will not be able to re-start message. ERASE R-VOL operation. To delete the pair forcibly, try again with Force option. W 0 6010 9155 The history file has been updated.
Table 52 Error Codes — Part Code 6010 (continued) Part Code Error Number Error Message Recommended Action 6010 9308 You set the same path more than once. The duplicate paths are excluded. Because there were W overlapped paths in the added paths, the overlapped paths were eliminated. Click [OK] and continue. 0 6010 9309 All paths which you set have already been registered. This operation will terminate because there is no path which can be added.
Table 52 Error Codes — Part Code 6010 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6010 9360 The specified value exceeds the range. Alternatively, the relationship between the specified values is not appropriate. Check the specified values and retry the operation. W 0 6010 55035 If you plan to create a pair with the specified LUSE volumes, a DKC path is required. Select Add RCU command, and then register a DKC path.
Table 52 Error Codes — Part Code 6010 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6010 59030 The monitoring data saved at To continue the operation, present will be deleted. click [OK]. To cancel the operation, click [Cancel]. i 5 To continue processing, click i [OK]. To stop processing, click [Cancel]. 5 The monitoring data currently saved will be deleted if you change the setting of the monitoring switch.
Table 52 Error Codes — Part Code 6010 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6010 65772 An external volume is assigned to two or more quorum disk IDs. An external volume cannot be used for multiple quorum disk IDs. Assign another external volume not used in the quorum disk IDs, and then retry the operation.
Table 52 Error Codes — Part Code 6010 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6010 69034 The number of preview data exceeds the maximum. Click [OK]. Apply the Preview data to the disk storage system, and then retry the operation. W 0 Select M-VOLs so that different CU numbers do not coexist in the M-VOLs, and retry the operation. W 5 W 5 No more preview data can be stored.
Table 53 Error Codes — Part Code 6105 Part Code Error Number Error Message Recommended Action 6105 56524 This function cannot be used Select another window. To by the storage partition set this function, contact the administrator. storage administrator.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message 6505 7111 6505 Recommended Action Severity Level Failure Level An error occurred during SVP If the error occurs after processing. If this problem retrying, call HP technical persists, call HP technical support. support. E 2 7310 This error code is not registered. If the error occurs after retrying, call HP technical support. E 5 6505 8000 An error occurred during SVP Retry the operation.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message 6505 8706 6505 Recommended Action Severity Level Failure Level Parameter specified by XP Enter the correct data. Continuous Access operation is invalid. i 4 8708 The pair status of the secondary data volume is incorrect. Refresh the window, and check the pair status. If possible, retry the operation on the secondary data volume. i 4 6505 8709 XP Continuous Access operation was rejected.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message 6505 8721 6505 Recommended Action Severity Level Failure Level Path creation has not finished Check the path connections yet. between the local and the remote storage systems, and then retry the operation. E 4 8722 Path creation failed. Check the path connections between the local and the remote storage systems, and then retry the operation.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 8731 The existing logical addresses Delete the DKC once, and are not the same. then add the DKC using the same logical address. i 4 6505 8733 XP Continuous Access Journal or Universal Replicator for Mainframe is not installed in the subsystem.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 8744 The specified primary data volume cannot be used. Check whether the primary data volume is in any of the following conditions: W 4 • Data in the primary data volume is being copied; correction copy or drive copy is in progress. • The primary data volume is in correction access condition. • The primary data volume is blocked.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 8753 An internal error occurred. Check the SSB log, and then E call HP technical support. 6505 8757 One side of the cache or the Check the status of the cache W shared memory is blocked in and the shared memory in the the primary storage system. primary storage system. Ensure that the cache and shared memory is not blocked.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 8795 The operation failed because Check the status of the i the specified primary data primary data volume from the volume was used by Business host or the SVP. Copy or ShadowImage for Mainframe and satisfied one of the following conditions: Failure Level 4 • The volume was a Business Copy S-VOL in non-PSUS status.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action 6505 8819 The specified secondary data Check the status of the volume must not be: secondary data volume.
Table 54 Error Codes — Part Code 6505 (continued) 274 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 8835 The Add Pair (Paircreate) operation failed because you tried to create volume pairs which exceeded the licensed capacity of the secondary subsystem. See the license key at the secondary storage system and check the licensed capacity of volumes. To create more pairs, purchase a license key for larger capacity.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 8922 The primary subsystem does not support remote copy via serial interface. Check whether the primary storage system supports remote copy via serial interface. Install the microcode that supports remote copy via serial interface, or execute remote copy via fibre interface. E 4 6505 8924 Logical paths are defined to the port on the remote subsystem.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 8977 The Add Pair (Paircreate) Check the status of the operation failed because the specified secondary data specified secondary data volume. volume was used by Flex Copy XP. W 0 6505 8980 The operation failed because the licensed capacity of Volume Retention Manager on the remote subsystem was exceeded.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message 6505 58017 6505 Recommended Action Severity Level Failure Level The specified volume is being Check the status of the connected by a mainframe specified volume from the host. mainframe host. i 0 58018 The specified volume is a reserve volume of a mainframe host. Check the status of the specified volume from the mainframe host.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 58031 The threshold for starting creation of asynchronous journal must be larger than the threshold for ending creation of asynchronous journal. Ensure that the threshold for starting creation of asynchronous journal is larger than the threshold for ending creation of asynchronous journal.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 58070 Invalid parameter (Suspend Condition-Master Journal Failure). Check the specified Suspend i Condition parameter. 0 6505 58071 Invalid parameter (Suspend Condition-Restore Journal Failure). Check the specified Suspend i Condition parameter. 0 6505 58072 The pair status has not changed yet.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message 6505 58084 6505 Recommended Action Severity Level Failure Level The specified primary data Check the status of the volumes cannot be paired specified primary data with another volume, because volume. the primary data volume is used as a journal volume. i 0 58085 The specified primary data Check data volumes in the volume is not registered in the specified primary journal specified journal group. group.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 58096 The specified volume is a reserve volume of a mainframe host. Check the status of the specified volume from the mainframe host. i 0 6505 58097 XP Continuous Access Journal or Universal Replicator for Mainframe is not installed in the primary subsystem.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 58105 XP Continuous Access Journal or Universal Replicator for Mainframe is not installed in the remote subsystem. XP Continuous Access Journal i or Universal Replicator for Mainframe must be installed in both the local and remote storage systems when you create paths or pairs with XP Continuous Access Journal or Universal Replicator for Mainframe.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 58270 The Add Pair (Paircreate) operation failed because of either of the following reasons. Check the mirror status and W the mirror ID of the specified restore journal group. 0 Check the following items on i the Data Retention Utility window if the specified secondary data volume is an open-system volume.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message 6505 58277 6505 6505 Recommended Action Severity Level Failure Level The specified secondary data Check data volumes in the volume is not registered in the specified secondary journal specified journal group. group. i 0 58278 The specified restore journal group is not registered. Check the status of the specified restore journal group.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message 6505 58287 6505 Recommended Action Severity Level Failure Level The command was rejected Check the command because the command was parameters. issued to the secondary data volume. The command is supposed to be issued to the primary data volume. i 0 58288 The specified primary data Check the status of the volume is already paired with specified primary data another volume. volume.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 58296 The specified volume is used Check whether the specified W by another program product.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 58323 The Add Pair (Paircreate) Specify another primary data W operation failed because the volume, and retry the specified primary data operation. volume was being used by XP Continuous Access Asynchronous or TrueCopy Asynchronous for Mainframe. 0 6505 58324 The Add Pair (Paircreate) Confirm the controller type of W operation failed because the the RCU.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message 6505 58329 6505 Recommended Action Severity Level Failure Level The Add Pair (Paircreate) Call HP technical support. operation or the Resume Pair (Pairresync) operation cannot be performed because the journal cache for the master journal group is not empty and contains data. W 0 58333 The parameter related to the Check the attribute of the inflow cannot be changed specified journal group.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 58342 The specified volume cannot be used as a journal volume because of a Data Retention Utility setting or a Volume Retention Manager setting. Check the setting of the W volume in the Data Retention Utility window or the Volume Retention Manager window.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message 6505 58353 The operation failed because the specified secondary data volume was one of the following: • • • • Recommended Action Severity Level Extract the possible W combination of program products from the combinations of program products described in the An S-VOL of Business message. Check the status of Copy.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message 6505 58355 The specified secondary data Check whether the specified volume is used by one of the secondary data volume is following program products. used by the following program products.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 58485 The Add Pair (Paircreate) Confirm the state of the W operation failed because the specified primary data in the specified primary data XP Snapshot window. volume was one of the following: Failure Level 5 • the specified volume was a P-VOL of XP Snapshot and was in Reverse Copy status. • the specified volume was an S-VOL of XP Snapshot.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action 6505 58502 The operation failed because the capacity of the secondary subsystem has exceeded the licensed capacity of Data Retention Utility. Confirm the licensed capacity W of the Data Retention Utility of the secondary storage system. To perform the specified operation, purchase a license key that allows you to use a capacity larger than the current capacity.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 58532 The Add Pair (Paircreate) Check the emulation type of operation failed because the the master and the restore emulation type of the master journal group. journal group was different from the emulation type of the restore journal group.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 58564 The Add Pair (Paircreate) operation failed because the specified primary data volume is being shredded by Data Retention Utility. Confirm that the shredding W has completed in the Data Retention Utility window, and then retry the operation. 0 Retry the operation after the shredding is completed.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action 6505 58595 The Paircreate operation failed because the XP Continuous Access Journal function of the secondary subsystem does not support LUSE volumes. Confirm that the XP W Continuous Access Journal function of the secondary storage system supports LUSE volumes.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message 6505 58606 6505 Recommended Action Severity Level Failure Level Journal groups cannot be Check the status of the deleted from the extended specified extended consistency group (EXCTG), consistency group (EXCTG). because the specified EXCTG was not registered. W 0 58607 Journal groups cannot be Check the journal groups in deleted from the extended the specified extended CT consistency group (EXCTG), group.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action 6505 58616 The specified journal group Check the state of the journal W cannot be added to extended group in the storage system consistency group (EXCTG). where the specified journal group belongs to, or the installation status of the program product.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message 6505 58629 The specified operation failed If this problem persists call HP because of a temporary path technical support. failure. Retry the operation. If this problem persists, call HP technical support. 6505 58641 The specified volume cannot be used as a journal volume because the volume is set by Cache Residency Manager or Cache Residency Manager for Mainframe.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 58685 Delta resync operation failed because the specified primary data volume was not a data volume of XP Continuous Access or TrueCopy for Mainframe, or the pair status of the primary data volume was invalid.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action 6505 58690 The recovery to the status Check the status on the ready for Delta resync failed, primary data volume. because the status of the specified primary data volume was one of the following: Severity Level Failure Level W 0 • The primary data volume is being copied; correction copy or drive copy is in progress. • The primary data volume is in correction access status.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Severity Level Failure Level 6505 58696 The specified volume cannot Check the I/O suppression be used as a journal volume mode of the specified because the volume is an volume. external volume to which the I/O suppression mode is enabled. W 0 6505 58697 The journal volume cannot be Check the mirror status of the W deleted from the specified specified journal group. journal group because of the mirror status.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action 6505 58704 The operation to change the status to the status ready for Delta resync failed because the status of the volumes was one of the following: Check the status of the data W volumes in the XP Continuous Access, TrueCopy for Mainframe, XP Continuous Access Journal, or Universal Replicator for Mainframe window. 0 Check the status of the specified secondary data volume.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 58717 The licensed capacity of XP Continuous Access Asynchronous or TrueCopy Asynchronous for Mainframe on the RCU is insufficient. Check the licensed capacity W of this program product and the related program products.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6505 58720 The licensed capacity of XP Continuous Access Asynchronous or TrueCopy Asynchronous for Mainframe on the MCU is insufficient. Check the licensed capacity W of this program product and the related program products.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 66592 The format of CU (P-VOL) is invalid. Check the contents of the spreadsheet. E 5 6505 66593 The value entered as CU (P-VOL) is outside the setting range. Check the contents of the spreadsheet. E 5 6505 66594 The number of digits of LDEV Check the contents of the (P-VOL) is invalid. spreadsheet.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message 6505 66612 6505 Recommended Action Severity Level Failure Level The format of CU (local VOL) Check the contents of the is invalid. spreadsheet. E 5 66613 The value entered as CU (local VOL) is outside the setting range. Check the contents of the spreadsheet. E 5 6505 66614 The number of digits of LDEV Check the contents of the (local VOL) is invalid. spreadsheet.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message 6505 66633 6505 Recommended Action Severity Level Failure Level The number of digits of R-JNL Check the contents of the is invalid. spreadsheet. E 5 66634 The format of R-JNL is invalid. Check the contents of the spreadsheet. E 5 6505 66635 The value entered as R-JNL is Check the contents of the outside the setting range. spreadsheet. E 5 6505 66636 The number of digits of VOL pair type is invalid.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 66654 The number of digits of Range is invalid. Check the contents of the spreadsheet. E 5 6505 66655 The format of Range is invalid. Check the contents of the spreadsheet. E 5 6505 66656 The value entered as Range is outside the setting range. Check the contents of the spreadsheet. E 5 6505 66657 The number of digits of Priority is invalid.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 66675 The syntax of the definition statement is invalid. Check the contents of the spreadsheet. E 5 6505 66676 The specified P-VOL is not mounted. Check the contents of the spreadsheet. E 5 6505 66677 The specified P-VOL is not mounted. Check the contents of the spreadsheet.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action 6505 68007 The Add Pair (Paircreate) operation failed. Confirm that the LDKC W number of the secondary data volume and the LDKC number of the restore journal group is the same. 0 The LDKC number of the specified secondary data volume is different from the LDKC number of the specified restore journal group.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action 6505 68024 The operation failed because Check the microcode version W the current microprogram of the connected storage version does not support system. Delta Resync. 0 6505 68025 The specified primary data Install the Disaster Recovery volume is used as a pair Extended function in the volume of XP Continuous primary storage system.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action 6505 68781 The specified operation failed The specified master journal because “LU” was specified group runs on the 2DC for the Error Level. configuration in which XP Continuous Access or XP Please specify “Group” for the Error Level, and retry the External Storage Access Manager cooperates. operation Severity Level Failure Level W 0 W 0 W 0 W 0 Specify Group for the Error Level.
Table 54 Error Codes — Part Code 6505 (continued) 314 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 68811 The specified volume cannot be used as a journal volume because it is used by FICON(R) Data Migration. Specify a volume that is not used by FICON(R) Data Migration. W 0 6505 68812 A pair could not be created because the specified secondary data volume was an XP Thin Provisioning volume whose capacity was being changed.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 68850 The operation failed, because Specify Group for the the consistency (CT) group of [Range], and then retry the specified data volume was operation. being shared with multiple primary and secondary storage systems, and LU was specified for the [Range].
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 68863 The operation failed, because Confirm the number of remote W the number of assignable command devices that has remote command device to a been assigned to a mirror. mirror exceeded the maximum.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action 6505 68905 The operation failed because Verify the attribute of the the attribute of the specified specified journal group. journal group was Master & Restore. The following options cannot be changed for the Master & Restore journal group. Severity Level Failure Level W 5 • Data overflow watch. • Use of cache. 6505 68906 A journal volume cannot be Call HP technical support.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action 6505 68914 The operation failed because the specified primary data volume was used by another mirror of the journal group, and the status of a pair in the mirror was in transition (COPY/ Suspending/ Deleting/ HOLDING). Verify that the status transition W of the pair in the mirror is completed, and then retry the operation.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action 6505 68917 The operation failed because Verify the status of specified the specified secondary data secondary data volume. volume was in one of the following status. Severity Level Failure Level W 5 • The consistency (CT) group of the specified data volume was being shared by multiple primary and secondary storage systems. • It is a LUSE volume.
Table 54 Error Codes — Part Code 6505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 68925 The operation to create a Verify the primary data pair for Delta resync failed volume. because the pair status of the specified primary data volume was not PAIR. W 5 6505 68926 Delta resync operation failed because the pair status of the specified primary data volume was not appropriate.
Table 56 Error Codes — Part Code 6510 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6510 5030 The displayed information has not been changed. Specify the data that you want to register in the SVP and retry the operation. W 0 6510 5137 The Operation value is invalid. Specify the correct value. Check the contents, and retry. W 0 6510 5138 The value specified for Check the contents, and retry. W Gathering Interval is invalid.
Table 56 Error Codes — Part Code 6510 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6510 9024 Are you sure you want to Ensure that the associated exchange the specified ports? channel paths are offline. Confirm the associated channel paths are off-line. W 5 6510 9025 Are you sure you want to Remove the remote copy W switch the ports? If the remote paths that are associated with copy paths exist on the ports, the ports. delete them beforehand.
Table 56 Error Codes — Part Code 6510 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6510 9115 The monitoring was stopped by another operator. The graph will be closed. Click [OK]. i 0 6510 9116 Another operator has Click [OK]. changed the Gathering Interval value. The graph will be closed. i 0 6510 9117 Are you sure you want to close the graph? To close the graph, click [OK]. Otherwise, click [Cancel].
Table 56 Error Codes — Part Code 6510 (continued) Part Code Error Number Error Message Recommended Action 6510 9308 You set the same path more than once. The duplicate paths are excluded. Because there are duplicated W paths in the added paths, the duplicated paths will be eliminated. Click [OK] to continue. 0 6510 9309 All paths which you set have already been registered. This operation will terminate because there is no path which can be added.
Table 56 Error Codes — Part Code 6510 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6510 55229 You want to forcibly delete pairs, but there are some pairs where Group is not specified as the range. Specify normal deletion, or specify Group as the range. W 0 W 0 Specify Group as the range when you want to forcibly delete pairs. 6510 55644 [Warning] To delete pairs, click [Yes]. There are some pairs where Otherwise, click [No].
Table 56 Error Codes — Part Code 6510 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6510 59010 WARNING: Check the contents of the W primary and secondary Initial copy mode None is volumes. If the contents selected for some volume match, click [Yes]. Otherwise, pair. Are you sure that the primary data volume and the click [No].
Table 56 Error Codes — Part Code 6510 (continued) Part Code Error Number Error Message Recommended Action 6510 59043 The number of journal volumes in some journal groups exceeds the maximum. Adjust the number of journal volumes. Reduce the number of journal W volumes to be registered, or increase the number of journal volumes to be deleted. 0 6510 59100 The same volume is stored more than once in the Preview list.
Table 56 Error Codes — Part Code 6510 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6510 59115 The number of Preview data may have exceeded the limit, or too large number of data is selected. Check the amount of the W Preview data. If the amount of the Preview data is too large, clear the Preview data by clicking [Apply], and retry the operation. Failure Level 5 If the amount of Preview data is small or there is no Preview data, too much data is selected.
Table 56 Error Codes — Part Code 6510 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6510 59329 The serial number of the local DKC is entered. Select the check box when you add the journal group of the local DKC to the extended consistency group (EXCTG). Check the check box when W you add the journal group of the local DKC to the extended consistency group (EXCTG).
Table 56 Error Codes — Part Code 6510 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6510 65806 The operation failed because Verify the journal group of the journal group of the the specified data volume. specified data volume was not a journal group for the 3DC configuration of three XP Continuous Access Journal sites.
Table 56 Error Codes — Part Code 6510 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6510 69018 There are two or more LDKC numbers for the specified data volume. In this operation, specify only one LDKC number. Check the LDKC number for the specified data volume, and specify only one LDKC number. W 0 6510 69019 The number of data volumes exceeds the maximum. Reduce the number of data W volumes and retry the operation.
Table 58 Error Codes — Part Code 6610 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6610 7303 An error occurred in client logic. Call HP technical support. E 2 6610 7440 An error occurred during processing. If this problem persists, call HP technical support. If the error occurs after retrying, call HP technical support. E 2 6610 8101 The system cannot apply the new configuration. Do you want to refresh? Click [Refresh], and retry.
Table 58 Error Codes — Part Code 6610 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6610 9104 Do you want to change the mode? To apply settings in the Preview list to the disk storage system, click [OK]. i 0 6610 9105 The value that is under setup To discard the current settings i is not reflected yet. Do you and close the window, click want to exit? [OK]. Otherwise, click [Cancel].
Table 58 Error Codes — Part Code 6610 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6610 9122 Are you sure you want to export pair status? To export, click [OK]. To cancel the operation, click [Cancel]. i 0 6610 9127 Are you sure you want to close all active graphs? To close the graphs, click [OK]. Otherwise, click [Cancel]. i 0 6610 9128 The specified volume was not Click [OK], and then specify i found. the correct volume.
Table 58 Error Codes — Part Code 6610 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6610 55039 You are specifying Group for the range and trying to manipulate the same mirror. Select only one data volume pair in the mirror when you specify Group for the range. Check the range setting. If i you specify Group, select only one data volume pair in the mirror. 0 6610 55202 The specified controller ID cannot be used.
Table 58 Error Codes — Part Code 6610 (continued) Part Code Error Number Error Message 6610 59004 6610 Severity Level Failure Level An error occurred. Check the Check the error information. error details. i 0 59005 An invalid value is specified. Specify the valid value. i 0 6610 59006 No more journal volumes can Check the number of journal i be registered, or too many volumes in the specified volumes are selected. journal group, or check the number of the selected volumes.
Table 58 Error Codes — Part Code 6610 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6610 59031 The monitoring data saved at present will be deleted when the monitoring switch is set to Enable the next time. To continue processing, click i [OK]. To stop processing, click [Cancel]. Failure Level 5 The monitoring data currently saved will be deleted when you change the setting of the monitoring switch. If necessary, use the Export Tool to save the monitoring data.
Table 58 Error Codes — Part Code 6610 (continued) Part Code Error Number Error Message Recommended Action 6610 59100 The same volume is stored more than once in the Preview list. Use the sort function to W identify volumes with the same LDKC number, the same CU number and the same LDEV number. 0 Use the sort function to identify volumes with the same LDKC number, the same CU number and the same LDEV number.
Table 58 Error Codes — Part Code 6610 (continued) Part Code Error Number Error Message Recommended Action Severity Level 6610 59115 The number of Preview data may have exceeded the limit, or too large number of data is selected. Check the amount of the W Preview data. If the amount of the Preview data is too large, clear the Preview data by clicking [Apply], and then retry the operation. Failure Level 5 If the amount of Preview data is small or there is no Preview data, too much data is selected.
Table 58 Error Codes — Part Code 6610 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6610 59323 The entered parameter is invalid. Check the entered parameter. W 0 Check whether the specified W journal groups include journal groups which belong to an extended consistency group (EXCTG). 0 The serial number, the LDKC number or the journal group to be added is not specified.
Table 58 Error Codes — Part Code 6610 (continued) Part Code Error Number Error Message 6610 59335 6610 Recommended Action Severity Level Failure Level The value of the path watch Check the value of the path time is not entered or is watch time. outside the range. Check the value of the path watch time. W 0 65663 The specified LDKC number is incorrect. Specify the correct LDKC number. Specify the correct LDKC number.
Table 58 Error Codes — Part Code 6610 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6610 69019 The number of data volumes exceeds the maximum. Reduce the number of data W volumes and retry the operation. When the number of volume pairs has already reaches the maximum value, you cannot create volume pairs any further.
Table 59 Error Codes — Part Code 6805 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6805 8659 Install necessary PCBs. Install necessary PCBs. E 3 6805 55009 An invalid cache resource number (CLPR No.) was detected. Correct the cache resource E number (CLPR No.), and then retry the operation. If this problem persists, call HP technical support. 3 6805 55010 An invalid storage resource number (SLPR No.) was detected.
Table 59 Error Codes — Part Code 6805 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6805 55219 The Sleep Time setting is incorrect. Correct the setting, and then retry. If the same problem persists despite retrying, call HP technical support. W 5 6805 55220 The SLPR number is duplicated. Correct the setting, and then retry. If the same problem persists despite retrying, call HP technical support.
Table 60 Error Codes — Part Code 6810 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6810 55219 The Sleep Time setting is incorrect. Correct the setting, and then retry. If the same problem persists despite retrying, call HP technical support. i 0 6810 59046 This function will apply the To continue processing, click i setting to all the target CLPRs. [OK]. To stop processing, This function will overwrite click [Cancel].
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message 7005 6023 7005 Recommended Action Severity Level Failure Level The SVP is busy. Please wait If the same problem persists for a while, and then retry the despite retrying, call HP operation. technical support. W 3 6502 Processing in progress. Please wait for a while, and then retry the operation. Wait a few seconds, and retry the operation. W 0 7005 6503 The target volume status is being changed to SMPL.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7005 8505 The command has been rejected, because the operation will not function with the current pair status. See the section describing E creating pairs and the pair status in the HP StorageWorks XP24000/XP20000 Business Copy Software User's Guide for the relationship between the status of pairs and the commands that can be accepted.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message 7005 8518 7005 Recommended Action Severity Level Failure Level You cannot create a pair, Check the emulation type. because the track format is different for each. Make sure that the specified emulation type is the same for both. i 0 8519 You cannot set a pair Check the volume capacity. because the number of cylinders is different for each. Make sure that the capacity is the same for both.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7005 8533 The command has been rejected, because the emulation type of the specified volume is not supported or the specified S-VOL is used as a data volume of XP Continuous Access Journal. Specify the volume of the W supported emulation type.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7005 8549 The P-VOL is not implemented. You cannot execute the operation for the volume which is not implemented. i 0 7005 8550 The command has been E • Restore the blocked rejected, because the volume, and then retry the specified P-VOL is blocked or operation. used as a system disk. • The system disk cannot be specified as a P-VOL. Specify another volume.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7005 8562 The command code sender is Call HP technical support. invalid. E 0 7005 8563 The volume type is invalid. Check the contents, and retry. i 0 7005 8564 The volume type is invalid. Check the contents, and retry. i 0 7005 8565 The command code sender is Call HP technical support. invalid.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7005 8580 The specified volume is for backup servers only. You cannot use the volume. Specify other volume, and retry the operation. i 0 7005 8581 The specified volume is not for backup servers only. Check the contents, and retry. i 0 7005 8582 The emulation type of the target volume is being changed. Wait a few seconds, and retry the operation.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level 7005 8597 The command has been rejected, because the number of pairs created with the specified P-VOL has reached the maximum. Pairs cannot be created with W the specified P-VOL any more. See the Create Pair Operation section in the HP StorageWorks XP24000/XP20000 Business Copy Software User's Guide for the composition of pairs.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7005 8608 The specified S-VOL is not defined. Refresh the screen, and retry the operation. i 0 7005 8609 The specified volume is not set as a reserved volume. Check the contents, and retry. i 0 7005 8610 The S-VOL is a target volume Release the XP Auto LUN for Auto LUN. setting. i 0 7005 8611 The specified volume is an S-VOL. Check the volume status.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7005 8623 The command has been rejected because the specified volume is used as S-VOL of XP Continuous Access pair or XP External Storage Access Manager pair. The S-VOL of XP Continuous Access pair or XP External Storage Access Manager pair cannot be used as a reserved volume. Specify another volume.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7005 8638 The command has been rejected, because the specified P-VOL is set for use in Cache Residency Manager. You cannot execute the specified operation. Release the Cache Residency Manager setting for the operation. i 0 7005 8639 The command has been You cannot execute the rejected, because the specified operation.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message 7005 8647 7005 Recommended Action Severity Level Failure Level The Reverse Copy command Delete the XP Continuous has been rejected, because Access pair. the S-VOL is shared as the S-VOL of a XP Continuous Access pair. i 0 8648 The boot device and the P-VOL do not match in the Paircreate command. Check the specified volume number.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7005 55264 The command was rejected, because you tried to create a volume pair formed with a volume to which VMA is set by Data Retention Utility and a volume without VMA. You cannot create a pair using these volumes. i 0 Increase the licensed E capacity of Data Retention Utility, and retry the operation.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level 7005 58001 The operation of the L2 pair failed because the L1 pair was in COPY(SP) status, PSUS(SP) status or COPY(RS-R) status. Wait until the L1 pair status i changes to PSUS or PAIR, and then retry the operation. 0 7005 58002 The Quick Restore command has been rejected because the specified pair is composed of a normal volume and a customized volume (CV).
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action 7005 58262 A pair cannot be created because shared memory for differential tables is insufficient. Add sufficient shared memory E to create a pair. 7005 58299 The operation failed because Check the requirements for the specified P-VOL was a using the volume with XP data volume of XP Continuous Continuous Access Journal. Access Journal.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7005 58480 The operation cannot be performed, because the specified S-VOL is a V-VOL for XP Snapshot. Specify another volume. W 5 7005 58481 The operation cannot be performed, because the specified S-VOL is a pool volume. Release the pool volume or select another volume.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action 7005 58573 This function is not supported. Check whether the E DKCMAIN microcode version and the SVP microcode version are mismatched. 3 7005 58574 An error occurred while If this problem persists, call connecting to the subsystem. HP technical support. Wait for a while, and then retry the operation.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level 7005 58630 The operation failed because the specified P-VOL was used by Delta resync of XP Continuous Access Journal. The command cannot be W executed in the current status of XP Continuous Access Journal pair.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7005 68739 The command has been rejected, because the specified reserved volume is an XP Thin Provisioning volume not associated with a pool. Associate the XP Thin Provisioning volume with a pool, and then retry the operation. i 5 7005 68743 The command has been rejected, because Quick Format is performed on the specified P-VOL.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7005 68803 The Quick Restore command has been rejected because P-VOL or S-VOL of Business Copy is combined with XP Continuous Access Asynchronous, and also CLPR numbers of P-VOL and S-VOL of Business Copy are different in the specified pair. Delete the XP Continuous i Access Asynchronous pair, and then retry the operation, or use Reverse Resync instead.
Table 61 Error Codes — Part Code 7005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7005 68839 The command has been rejected, because the specified reserved volume is a volume of XP Thin Provisioning whose zero data is being discarded. Wait until the process of i discarding zero data is completed, and then retry the operation. 7005 68867 The command has been Specify another volume.
Table 63 Error Codes — Part Code 7010 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7010 5121 The data has been changed. If you select another tab (page), the settings will be discarded. Are you sure you want to continue? Apply the data in the Preview W List. To stop the transaction, click [OK] and continue the operation. 0 7010 5122 No data has been changed. Go on to the next operation. W 0 7010 5123 The password is invalid.
Table 63 Error Codes — Part Code 7010 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7010 9002 The request operation has completed. The operation was ended normally. Execute the next operation. i 0 7010 9005 An error occurred. Check the An error occurred during the i error code. indicated operation. See the error code for each operation in the Preview List. 0 7010 9101 Do you want to cancel? To cancel, click [OK].
Table 63 Error Codes — Part Code 7010 (continued) Part Code Error Number Error Message Recommended Action Severity Level 7010 66102 Information was updated by Click [OK], and then continue W other users. The list will scroll the operation. to the top. 5 7010 66560 The maximum number of Change the number of pairs Pairs or Volumes that can be or volumes displayed in displayed in the Preview List Preview to 16,384 or less. is 16,384.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7105 8501 The command has been rejected, because the previous command is being processed. Wait until the previous operation completes. W 5 7105 8502 You cannot reserve the Delete the XP Continuous volume, because a XP Access pair. Continuous Access pair exists in the same subsystem frame.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7105 8511 You cannot reserve the volume, because a path group is set. Detach the S-VOL from the host, or delete the XP Continuous Access path. i 0 7105 8512 Cannot perform Resync or Suspend operation because of the path group setting. Vary the S-VOL offline from i the mainframe host, and then issue the command again.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7105 8528 An internal logic error occurred. Call HP technical support. E 0 7105 8529 An internal logic error occurred. Call HP technical support. E 0 7105 8530 An internal logic error occurred. Call HP technical support. E 0 7105 8531 An internal logic error occurred. Call HP technical support.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7105 8542 Failed to complete the initial shared memory setup. Call HP technical support. E 0 7105 8543 The shared memory size is different. Call HP technical support. E 0 7105 8544 16 Mbytes of shared memory Check the contents, and retry. i is available. 0 7105 8545 A power supply failure is detected. Call HP technical support.
Table 64 Error Codes — Part Code 7105 (continued) 374 Part Code Error Number Error Message Recommended Action Severity Level 7105 8558 The command has been rejected, because the specified volume is blocked or used as a system disk. E • Restore the blocked volume, and then retry the operation. Failure Level 5 • The system disk cannot be specified as a reserved volume. Specify another volume. 7105 8559 The volume is being formatted. Wait until the volume is formatted, and retry the operation.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7105 8575 The selected volume is not a reserved volume. Check the status of the volume. i 0 7105 8576 No reserved volume is available for use. Check the contents, and retry. i 0 7105 8577 The number of reserved volumes to be defined exceeds the maximum. Stop the operation of the Reserve volume setting, or delete the Reserve volume.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message 7105 8593 7105 Recommended Action Severity Level Failure Level The S-VOL is a source volume Release the XP Auto LUN for Auto LUN. setting. i 0 8594 The S-VOL is a target volume Release the XP Auto LUN for Auto LUN. setting. i 0 7105 8595 The specified S-VOL does not Refresh, and then retry the exist. operation. i 0 7105 8596 The specified volume is a reserved volume.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7105 8607 The command has been rejected, because the specified T-VOL is used as a M-VOL of TrueCopy for Mainframe pair. The requested command W cannot be executed in the current status of TrueCopy for Mainframe pair.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7105 8622 The command has been rejected, because the specified volume is used as a M-VOL of TrueCopy for Mainframe pair. The P-VOL of TrueCopy for Mainframe pair cannot be used as a reserved volume. Specify another volume. W 5 7105 8623 The command has been rejected, because the specified volume is used as a R-VOL of TrueCopy for Mainframe pair.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7105 8638 The command has been rejected, because the specified S-VOL is set for use in Cache Residency Manager for Mainframe. You cannot execute the specified operation. Release the Cache Residency Manager for Mainframe setting for the operation.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7105 8649 Because the boot device is the T-VOL in the DeletePair command, the flag does not match. Check the specified volume number. i 0 7105 8650 The boot device and the S-VOL do not match in the AddPair, Resync, or DeletePair command. Check the specified volume number. i 0 7105 8651 The SSID is invalid. Check the contents, and retry.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level 7105 8920 Because a L1 pair is F-Copy, Wait for Flash Copy i you cannot operate to L2. processing of a L1 pair being finished, and then execute operation of target pair. 0 7105 8941 The command was rejected because the specified CT Group is already used. Correct the specified CT Group and retry the operation again.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message 7105 56303 7105 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 56524 This function cannot be used by the storage partition administrator. Select another window. To set this function, contact the storage administrator.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level 7105 58260 The command has been rejected, because the specified S-VOL is used as a M-VOL of TrueCopy for Mainframe pair. The requested command W cannot be executed with the current status of the TrueCopy for Mainframe pair.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action 7105 58351 The Quick Restore command has been rejected, because the specified pair is composed of internal and external volumes, and also used as a Universal Replicator for Mainframe pair. Stop using the specified pair i for Universal Replicator for Mainframe, or specify a different pair, and then retry the operation.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7105 58575 An error occurred while connecting to the subsystem. Wait for a while, and then retry the operation. If this problem persists, call HP technical support. E 6 7105 58585 The operation failed because Volumes that do not belong the CU group of the specified to CU group 0 are currently volume is not supported. not supported. Specify another volume.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7105 68747 The command has been rejected because FICON(R) Data Migration Source Volume is used in the specified pair, and T-VOL is used with other program products. Cancel the setting to use the T-VOL with other program products, and then retry the operation.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7105 68770 The XP Business Copy Release the Cache Residency i Operation for FICON(R) Data Manager for Mainframe Migration failed, because the setting in the T-VOL. Cache Residency Manager for Mainframe setting was set in the T-VOL of the specified pair.
Table 64 Error Codes — Part Code 7105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7105 68803 The Quick Restore command has been rejected because S-VOL or T-VOL of ShadowImage for Mainframe is combined with TrueCopy Asynchronous for Mainframe, and also CLPR numbers of S-VOL and T-VOL of ShadowImage for Mainframe are different in the specified pair.
Table 65 Error Codes — Part Code 7110 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7110 5121 The data has been changed. If you select another tab (page), the settings will be discarded. Are you sure you want to continue? Apply the data in the Preview W List. To stop the transaction, click [OK] and continue the operation. 0 7110 5122 No data has been changed. Go on to the next operation. W 0 7110 5123 The password is invalid.
Table 65 Error Codes — Part Code 7110 (continued) Part Code Error Number Error Message Recommended Action 7110 9108 The option has been To continue processing, click W changed. If you continue [OK]. Otherwise, click processing before applying [Cancel]. the change, the option will be reset to the current setting. Do you want to continue processing? 0 7110 9109 Do you want to execute the Set Over operation? To continue processing, click W [OK]. Otherwise, click [Cancel].
Table 65 Error Codes — Part Code 7110 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7110 65662 The data has been changed. To continue processing, click W The settings will be discarded [OK]. Otherwise, click if you continue the [Cancel]. processing. Do you want to switch the LDKC? 5 7110 65729 Pairs cannot be created any more because XP Business Copy Operation for FICON(R) Data Migration is already registered to the specified volume.
Table 66 Error Codes — Part Code 8005 (continued) Part Code Error Number Error Message 8005 5099 8005 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 5510 The storage system is in internal process, or some other user is changing configuration. After you reply to this message, a window that shows only the Refresh button will be displayed.
Table 66 Error Codes — Part Code 8005 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8005 8001 An error occurred while connecting to the subsystem. Wait for a while, and then retry the operation. Retry the same operation E several times. If the same error occurs, call HP technical support. 6 8005 8100 An error occurred while connecting to the subsystem. Wait for a while, and then retry the operation. Retry the same operation E several times.
Table 66 Error Codes — Part Code 8005 (continued) Part Code Error Number Error Message Recommended Action 8005 55265 The parity group that contains Check the settings, and then the volume(s) to which Cache retry the operation. Residency Manager is set cannot be migrated to another CLPR. Severity Level Failure Level E 6 Remove the Cache Residency Manager settings from the volumes, and then migrate the parity group.
Table 66 Error Codes — Part Code 8005 (continued) Part Code Error Number Error Message 8005 58574 8005 Severity Level Failure Level An error occurred while If this problem persists, call connecting to the subsystem. HP technical support. Wait for a while, and then retry the operation. E 6 58575 An error occurred while If this problem persists, call connecting to the subsystem. HP technical support. Wait for a while, and then retry the operation.
Table 67 Error Codes — Part Code 8105 Part Code Error Number Error Message 8105 1002 The specified volume cannot Select another volume. be set as a command device or a component of a LUSE volume, because it is being used as the volume of XP Continuous Access, Business Copy, Auto LUN, or XP Snapshot. Select another volume. 8105 8105 8105 Severity Level Failure Level E 6 1003 You are trying to set multiple The configuration information E paths to the same volume has been already changed.
Table 67 Error Codes — Part Code 8105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8105 1011 An error occurred. If this problem persists, call HP technical support. The volume which links as an E expanded LU extend over CU#. The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact HP technical support. 2 8105 1012 LU path is set to a volume which links as an expanded LU.
Table 67 Error Codes — Part Code 8105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8105 1024 An error occurred. If this problem persists, call HP technical support. Fibre topology information is E invalid. (The specified value is not in the specification.) The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact HP technical support.
Table 67 Error Codes — Part Code 8105 (continued) Part Code Error Number Error Message Recommended Action Severity Level 8105 1064 You are trying to register the same WWN as the already registered one. Check the settings and request the setting of the configuration information again. The configuration information W has been already changed. Correct the specified contents, and request the setting of the configuration information again.
Table 67 Error Codes — Part Code 8105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8105 1111 An error occurred. If this problem persists, call HP technical support. A nickname is not specified E when the configuration change of LUN-Security is requested. The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact HP technical support. 2 8105 1116 An error occurred.
Table 67 Error Codes — Part Code 8105 (continued) Part Code Error Number Error Message Recommended Action 8105 1127 An error occurred. If this problem persists, call HP technical support. CHA high-speed mode is E specified to an unmounted CHA. The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact HP technical support. 2 8105 1128 An error occurred. If this problem persists, call HP technical support.
Table 67 Error Codes — Part Code 8105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8105 1135 An error occurred. If this problem persists, call HP technical support. When the PORT information E (Fibre Address/Fibre Topology/Channel Speed) is set, multiple change instructions are set to the same port. The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact HP technical support.
Table 67 Error Codes — Part Code 8105 (continued) Part Code Error Number Error Message Recommended Action 8105 1203 High Speed mode/MIX mode was specified. However, there are addresses to which High Speed mode/MIX mode cannot be set in the Fibre Addresses of the specified ports. The configuration information E has been already changed. High Speed mode/MIX mode was specified. However, there are topologies to which High Speed mode/MIX mode cannot be set in the topologies of the specified ports.
Table 67 Error Codes — Part Code 8105 (continued) Part Code Error Number Error Message Recommended Action 8105 1356 The host group cannot be added to the Initiator port. The port you are trying to set E is for XP Continuous Access. You must change the attribute (Target or RCU Target) when adding a host group. 6 8105 1357 S-VOLs remain on the Fibre-RCU port. This operation may cause a fatal damage to the S-VOLs. Stop this operation.
Table 67 Error Codes — Part Code 8105 (continued) Part Code Error Number Error Message 8105 1912 The specified volume is a Correct the settings, and then E remote command device, and retry the operation. therefore the command device setting or the command device security setting cannot be set or released. 6 8105 1918 An external volume is mapped to the external port to be operated. Delete the external volume that is mapped to the external port to be operated, and then retry the operation.
Table 67 Error Codes — Part Code 8105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8105 2015 An error occurred while connecting to the subsystem. Wait for a while, and then retry the operation. A communication error occurs. If the error occurs after retrying, call HP technical support. E 6 8105 2082 Processing is disabled because the host is mounted or the device is reserved. The host is mounted or the E device is reserved.
Table 67 Error Codes — Part Code 8105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8105 2516 A XP Continuous Access, XP Continuous Access Journal, or Universal Replicator for Mainframe pair is defined. Cancel or suspend the pair definition, and then retry the operation. Cancel or suspend the pair definition, and then retry the operation.
Table 67 Error Codes — Part Code 8105 (continued) Part Code Error Number Error Message 8105 3006 8105 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 3007 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 67 Error Codes — Part Code 8105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8105 5721 The parameter is invalid. Correct the invalid parameter. W 0 8105 5730 Duplicate definition error. Write one definition only in each tag. W 0 8105 5731 The current information is invalid. Correct the current information. W 0 8105 5740 There is a difference between Correct the name of the CHA. W the current CHA and the specified CHA.
Table 67 Error Codes — Part Code 8105 (continued) 410 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8105 5757 The same WWN is already registered. Correct the WWN. W 0 8105 5758 No name can be added to the group ID (00). Correct the group ID. W 0 8105 5759 The same name is already registered. Correct the name. W 0 8105 5761 The WWN does not exist. Correct the WWN. W 0 8105 5762 The name does not exist. Correct the name.
Table 67 Error Codes — Part Code 8105 (continued) Part Code Error Number Error Message Recommended Action Severity Level 8105 6524 The port information is inconsistent with PCB mode information. Correct the port information W or the PCB mode information. 8105 7060 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 68 Error Codes — Part Code 8107 Part Code Error Number Error Message 8107 5641 8107 8107 Recommended Action Severity Level Failure Level The number of lines exceeds Check the setting. the maximum number of lines of a spreadsheet. E 6 5642 The number of characters exceeds the maximum number of characters of a spreadsheet. E 6 5643 A time-out error occurred. If the error occurs after Wait for the SVP to reboot, retrying, call HP technical and then retry the operation. support.
Table 69 Error Codes — Part Code 8110 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8110 5773 The file path of the specified file by [File Name on Client] is incorrect. Correct the specified contents, and retry the operation. E 1 8110 5774 The file specified by [File Name on Client] is write-protected. Correct the specified contents, and retry the operation. E 1 8110 5775 A file access error occurred.
Table 70 Error Codes — Part Code 8111 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8111 5632 Modify mode released due to inactivity. Restart Modify mode (press the mode-switching button again) to continue. Modify mode released due E to inactivity. Restart Modify mode (press the mode-switching button again) to continue. 1 8111 5633 The file path should be from 1 to 255 characters. Correct the specified contents, and retry the operation.
Table 73 Error Codes — Part Code 8310 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8310 59018 The On-Demand status of all the groups of ports under the selected CHA is going to be changed. Do you want to continue? To change the On-Demand i status of all the groups of ports under the selected CHA, click [OK]. Otherwise, click [Cancel]. 0 8310 59019 The On-Demand status of the selected group of ports is going to be changed.
Table 74 Error Codes — Part Code 8505 (continued) Part Code Error Number Error Message Severity Level Failure Level 8505 8002 An error occurred during SVP If the same problem persists processing. If this problem despite retrying, call HP persists, call HP technical technical support. support. E 3 8505 8401 The status of the disk subsystem requires maintenance (for example, the subsystem is blocked, the shared memory is inconsistent, or some other factor). Call HP technical support.
Table 74 Error Codes — Part Code 8505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8505 55016 The value set as the maximum number of connections to each SLPR is invalid. SLPR No:%s Set the correct value for the E maximum number of connections to the SLPR, and then retry the operation. If this problem persists, call HP technical support.
Table 74 Error Codes — Part Code 8505 (continued) Part Code Error Number Error Message 8505 55026 The specified port name (port Specify the correct port name E number) is invalid. (port number), and then retry the operation. If this problem persists, call HP technical support. 5 8505 55027 The cache size is incorrect. Correct the settings of the E cache size, and then retry the operation. If this problem persists, call HP technical support.
Table 74 Error Codes — Part Code 8505 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8505 56527 While another user is logged into Remote Web Console, you cannot edit the information of the SLPR that the user owns. SLPR No:%s Confirm that no user is logged into Remote Web Console, and then retry the operation. E 5 8505 56536 The installation status of the SLPR has changed.
Table 74 Error Codes — Part Code 8505 (continued) Part Code Error Number Error Message 8505 58316 8505 Recommended Action Severity Level Failure Level Parity groups in CLPR are Wait a few seconds, and being migrated in the storage then retry the operation. system. Wait for a while, and then retry the operation. W 5 58317 CLPR capacity is being Wait a few seconds, and changed in the storage then retry the operation. system. Wait for a while, and then retry the operation.
Table 76 Error Codes — Part Code 8510 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8510 5030 The display information has not been changed. Specify what you want to register, and retry the operation. W 0 8510 7060 An error occurred in client logic. If this problem persists, call HP technical support. E 2 8510 7301 An error occurred in client logic. If this problem persists, call HP technical support.
Table 76 Error Codes — Part Code 8510 (continued) Part Code Error Number Error Message 8510 55636 The CLPR that has some Migrate all parity groups in parity groups cannot be the CLPR to another CLPR, deleted. Migrate all parity and then delete the CLPR. groups in the CLPR to another CLPR, and then delete the CLPR. 8510 57001 The partition configuration may contain some inconsistent information. To initialize partition configuration, select the Yes button. To stop the operation, select the No button.
Table 76 Error Codes — Part Code 8510 (continued) Part Code Error Number Error Message 8510 59110 8510 59114 Recommended Action Severity Level Failure Level SSIDs that are associated Check the settings. with the selected CU cannot be added to this SLPR, because too many SSIDs have been set in the SLPR. Delete unnecessary SSIDs from this SLPR, and then retry the operation. W 0 Ports in high-speed mode are Check the settings. set across multiple SLPRs.
Table 77 Error Codes — Part Code 8605 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8605 66822 The contents of the e-mail address information file are invalid. Register the email address information file again. E 5 8605 66823 A failure occurred while Check the state of E communicating with the SMTP communication with the SMTP server. server to solve this problem.
Table 78 Error Codes — Part Code 8610 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8610 65765 The same e-mail addresses are specified. Remove the duplicated email W addresses, and then register it again. 5 8610 69081 Send a test message. OK? Confirm the message, and then reply. i 5 8610 69082 Sending test message has been completed. Confirm the message, and then reply.
Table 79 Error Codes — Part Code 9005 (continued) Part Code Error Number Error Message 9005 7111 9005 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 7112 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 80 Error Codes — Part Code 9007 Part Code Error Number Error Message 9007 5099 9007 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 6012 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 82 Error Codes — Part Code 9105 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 9105 5511 The program product is not installed. Click [OK], and then install the program product. W 5 9105 5600 The settings of the security group are invalid. Click [OK], correct the security group settings, and then retry the operation. W 0 9105 5601 The settings of the host group Click [OK], correct the host W are invalid.
Table 82 Error Codes — Part Code 9105 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 9105 7060 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists call HP technical support. E 3 9105 7111 An error occurred during SVP processing. If this problem persists, call HP technical support. An error occurred during SVP E processing. If this problem persists, call HP technical support.
Table 83 Error Codes — Part Code 9107 Part Code Error Number Error Message Recommended Action Severity Level 9107 6012 An error occurred during SVP processing. If this problem persists, call HP technical support. An error occurred during SVP E processing. If this problem persists, call HP technical support. 9107 7060 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 84 Error Codes — Part Code 9110 (continued) Part Code Error Number Error Message Recommended Action Severity Level 9110 5619 The R-VOL/T-VOL cannot be set to the specified security group. Click [OK]. Ensure that the W R-VOL/T-VOL is not set to the specified security group, and retry the operation. 9110 5620 The selected volumes include Click [OK], check the some invalid volumes. selected volumes, and retry the operation. W 0 9110 5621 No item is selected.
Table 84 Error Codes — Part Code 9110 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 9110 9084 The specified group includes To delete the group, click some hosts. Are you sure you [Yes]. Otherwise, click [No]. want to delete the group? i 0 9110 9101 Do you want to cancel? To cancel the operation, click i [Yes]. Otherwise, click [No]. 0 9110 9102 Do you want to apply? To apply, click [Yes]. Otherwise, click [No].
Table 85 Error Codes — Part Code 9205 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 9205 5041 The number of issued commands exceeds the maximum. Reduce the number of set demands. W 5 9205 5511 The program product is not installed. Install the program product. W 5 9205 6012 An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support.
Table 85 Error Codes — Part Code 9205 (continued) Part Code Error Number Error Message Recommended Action 9205 8126 The logical volume is configured as a command device. Check the logical volume E configuration, and then retry the operation. 9205 8136 The command was rejected, The currently licensed because the licensed capacity capacity is insufficient. To was exceeded. increase the licensed capacity, buy a new license key.
Table 85 Error Codes — Part Code 9205 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 9205 66008 The number of digits is invalid. Check the contents of the Volume Retention Manager spreadsheet. E 5 9205 66009 The entered value is outside the setting range. Check the contents of the Volume Retention Manager spreadsheet. E 5 9205 66010 The format is invalid. Check the contents of the Volume Retention Manager spreadsheet.
Table 87 Error Codes — Part Code 9605 Part Code Error Number Error Message 9605 5013 9605 Recommended Action Severity Level Failure Level An error occurred during SVP If this problem persists, call processing. If this problem HP technical support. persists, call HP technical support. E 2 5030 No commands are issued. Issue a command again. E 5 9605 5041 The number of issued commands exceeds the maximum. Decrease the number of commands.
Table 87 Error Codes — Part Code 9605 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 9605 8120 The specified logical volume does not exist. Specify an open-system volume. E 5 9605 8122 This logical volume is busy. Retry a little later. E 5 9605 8123 This function is not supported. Check whether the E DKCMAIN microcode version and the SVP microcode version are mismatched. 5 9605 8124 This logical volume is a mainframe volume.
Table 87 Error Codes — Part Code 9605 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 9605 8150 You tried to set a retention Check the logical volume, E term to a logical volume and then retry the operation. whose access attribute is not Read Only or Protect. 5 9605 8151 You cannot shorten the retention term of the logical volume. To shorten it, call HP technical support. You cannot shorten the E retention term of the logical volume.
Table 87 Error Codes — Part Code 9605 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 9605 58413 The attribute of the virtual volume of the XP Snapshot cannot be changed. Select another volume. E 5 9605 58414 The attribute of the P-VOL or Select another volume. the S-VOL of the XP Snapshot cannot be changed. E 5 9605 58415 The VMA of the pool volume Select another volume. cannot be changed.
Table 87 Error Codes — Part Code 9605 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 9605 58432 A VMA cannot be set up on this logical volume because Auto LUN is using the logical volume. Release XP Auto LUN's use of E the logical volume, or set up the VMA on another logical volume. 5 9605 58433 An access attribute is set to the specified extent. Release the access attribute of the extent. E 5 9605 58434 This logical volume is busy.
Table 87 Error Codes — Part Code 9605 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 9605 58448 The specified logical volume Retry the operation after the E is blocked, or the LDEV is logical volume has recovered being formatted or shredded. from the blocked status or after the LDEV has been formatted or shredded. 5 9605 58449 The capacity of the logical Do one of the following: E volume is not the same as 1.
Table 88 Error Codes — Part Code 9610 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 9610 58405 There is an invalid value in the Extent information. If this problem persists, call HP technical support. E 3 9610 59106 If you set VMA, all the data To set VMA, click [OK]. or part of the data written in Otherwise, click [Cancel]. the logical volume will be deleted.
Table 90 Error Codes — Part Code 10110 (continued) Part Code Error Number Error Message Recommended Action Severity Level Failure Level 10110 65720 The length of the character string of the specified password is invalid. Specify a valid password. W 5 10110 65725 Specify the file name. Specify the file name.
2 Support and Other Resources Related Documentation • HP StorageWorks XP24000/XP20000 Disk Array Owner Guide • HP StorageWorks XP24000/XP20000 Remote Web Console User Guide You can find these documents on the HP Manuals website: http://www.hp.com/support/manuals In the Storage section, click Disk Storage Systems and then select a product.
http://www.hp.com/go/e-updates After registering, you will receive email notification of product enhancements, new driver versions, firmware updates, and other product resources. HP Websites For additional information, see the following HP websites: • http://www.hp.com • http://www.hp.com/go/storage • http://www.hp.com/support/manuals • http://www.hp.com/storage/spock Documentation Feedback HP welcomes your feedback.
Glossary A API Application program interface. C CCI Command control interface. An HP RAID manager. CHA Channel adapter. A device that provides the interface between the array and the external host system. Occasionally, this term is used synonymously with the term channel host interface processor (CHIP). CLPR Cache logical partition. CT Consistency. CTG Consistency group. CU Control unit. CU Control unit. CV Customized volume. D DASD Direct-access storage device. DFW DASD fast write.
M M-VOL Main volume. MCU Main control unit. MU Mirror unit. N NVS Nonvolatile storage. P P-VOL Primary volume. P.P. Program Product. PB Petabyte; equals 1,000^5 bytes (for physical storage such as hard disk drives) or 1,024 TB or 1,024^5 bytes (for logical storage). PCB Printed circuit board. PDEV Physical device. PS Power supply. PSUE Pair suspended-error (status). PSUS Pair suspended-split (status). R R-VOL Remote volume. RCP Remote control port. RCU Remote control unit.
V V-VOL Virtual volume. VDEV Virtual device. VLL Virtual LVI/LUN. VMA Volume management area. W WWN 448 Glossary World wide name.
