HP StorageWorks XP24000/XP20000 Remote Web Console Error Codes Part number: AE131-96014 Second edition: September 2007
Legal and notice information © Copyright 2007 Hewlett-Packard Development Company, L.P. Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor's standard commercial license. The information contained herein is subject to change without notice.
Contents About this Guide . . . . . . . . . . . . . . . . . . . . . . . . . . Intended Audience . . . . . . . . . . Related Documentation . . . . . . . . Document Conventions . . . . . . . . Conventions for Storage Capacity Values Graphical Interface Illustrations . . . . HP Technical Support . . . . . . . . . Subscription Service . . . . . . . . . HP Websites . . . . . . . . . . . . Documentation Feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figures 4 1 Sample Message Window (Information Level Message) . . . . . . . . . . . . . . . . 13 2 Message Window Format . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tables 1 Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 Error Codes — Part Code 0001 . . . . . . . . . . . . . . . . . . . . . . . . . 14 3 Error Codes — Part Code 0002 . . . . . . . . . . . . . . . . . . . . . . . . . 21 4 Error Codes — Part Code 0003 5 Error Codes — Part Code 0004 . . . . . . . . . . . . . . . . . . . . . . . . . 25 . . . . . . . . . . . . . . . . . . . . . . . . . 49 6 Error Codes — Part Code 0005 7 Error Codes — Part Code 0006 . . . .
40 Error Codes — Part Code 4010 . . . . . . . . . . . . . . . . . . . . . . . . . 170 41 Error Codes — Part Code 4105 . . . . . . . . . . . . . . . . . . . . . . . . . 172 42 Error Codes — Part Code 5105 . . . . . . . . . . . . . . . . . . . . . . . . . 173 43 Error Codes — Part Code 5110 . . . . . . . . . . . . . . . . . . . . . . . . . 176 44 Error Codes — Part Code 5205 . . . . . . . . . . . . . . . . . . . . . . . . . . 176 45 Error Codes — Part Code 5210 . . . . . . . . . . . . . . .
83 Error Codes — Part Code 9210 . . . . . . . . . . . . . . . . . . . . . . . . . 379 84 Error Codes — Part Code 9605 . . . . . . . . . . . . . . . . . . . . . . . . . . 379 85 Error Codes — Part Code 9610 . . . . . . . . . . . . . . . . . . . . . . . . . 385 86 Error Codes — Part Code 10010 . . . . . . . . . . . . . . . . . . . . . . . . . 386 87 Acronyms and Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . .
About this Guide This document lists the error codes and error messages for the HP Remote Web Console for HP storage systems, and provides recommended action for the error conditions.
Conventions for Storage Capacity Values HP XP storage systems use the following values to calculate physical storage capacity values (hard disk drives): • • • • 1 1 1 1 KB (kilobyte) = 1,000 bytes MB (megabyte) = 1,0002 bytes GB (gigabyte) = 1,0003 bytes TB (terabyte) = 1,0004 bytes HP XP storage systems use the following values to calculate logical storage capacity values (logical devices): • • • • • 1 1 1 1 1 KB (kilobyte) = 1,024 bytes MB (megabyte) = 1,0242 bytes GB (gigabyte) = 1,0243 bytes TB (te
• http://www.hp.com/support/manuals Documentation Feedback HP welcomes your feedback. To make comments and suggestions about product documentation, send a message to storagedocsFeedback@hp.com. All submissions become the property of HP.
About this Guide
1 HP StorageWorks XP Remote Web Console for Storage System Messages and Error Codes Remote Web Console for Storage System Messages “Sample Message Window (Information Level Message)” on page 13 shows a typical message window displayed by the HP Remote Web Console for HP storage system software.
• The word R-VOL in TrueCopy for Mainframe messages is equivalent to S-VOL in Continuous Access messages. • Part code: The ID of the application that issued the message. In “Sample Message Window (Information Level Message)” on page 13 the part code is 110. • Message number: Decimal number within the range of 0000 to 99999. In “Sample Message Window (Information Level Message)” on page 13 the message number is 9102.
Part Code Error Number Error Message Recommended Action 1001 A time-out error occurred. Please wait for the SVP to reboot, and then retry the operation. 0001 0001 Severity Level Failure Level The SVP reboots automatically. If the same error occurs despite retrying, call technical support.
Part Code Error Number Error Message Recommended Action 0001 4003 An error occurred. If this problem persists, please call technical support. 0001 4004 0001 Severity Level Failure Level Input the correct user name and log in again. E 2 An error occurred. If this problem persists, please call technical support. Input the correct password and log in again. E 2 4005 The user ID is already logged in.
Part Code Error Number Error Message Recommended Action 5099 An error occurred during SVP processing. If this problem persists, please call technical support. 0001 0001 Severity Level Failure Level If the same problem persists despite retrying, call technical support. E 2 5132 The specified user ID is already logged on, or the previous logon was not properly terminated. Please try again later. (By default, the session/RMI time-out is one minute.) Log on with other user's ID.
Part Code Error Number Error Message Recommended Action 5517 An error occurred during SVP processing. If this problem persists, please call technical support. 0001 Severity Level Failure Level If the same problem persists despite retrying, call technical support. E 2 5518 An error occurred during SVP processing. If this problem persists, please call technical support. If the same problem persists despite retrying, call technical support.
Part Code Error Number Error Message Recommended Action 0001 5556 The password is invalid. Check the setting, and then retry the operation. 0001 Severity Level Failure Level The password is invalid. Check the setting, then retry the operation. E 2 5557 The specified permission flag is invalid. Check the setting, and then retry the operation. The specified permission flag is invalid. Check the setting, then retry the operation. E 2 0001 5559 The specified authority flag is invalid.
Part Code Error Number Error Message Recommended Action 0001 6022 A file open error has occurred. Severity Level Failure Level If the same problem persists despite retrying, call technical support. E 2 6023 Failed to access the file. Check the setting, and then retry the operation. If the same problem persists despite retrying, please call technical support. Failed to access the file. Check the setting, then retry the operation.
Part Code 0001 0001 0001 Error Number Error Message Recommended Action 56545 The operation failed because the audit log is being processed. Please wait for a while, and then retry the operation. Severity Level Failure Level Please wait a while, then retry the operation. W 5 57106 An invalid value is included in the management file of the audit log. Please retry the operation. If the same problem persists despite retrying, call technical support.
Part Code Error Number Error Message Recommended Action 2008 An error occurred during SVP processing. If this problem persists, please call technical support. 0002 Severity Level Failure Level If nothing changes despite retrying, call technical support. E 3 2009 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists call technical support. E 2 0002 2010 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action 5130 0002 0002 Severity Level Failure Level A sequence error occurred. Please call the developer of the client program. Connection is terminated from the server due to the network failure etc. Please log on again. This error might occur and remain internally in the unlock function log when a user in View mode selects the Exit button, but this is not a problem. In other cases, call technical support.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0002 6502 Now processing. Please wait a while, and then retry the operation. Please log in again after a while. i 0 0002 6531 The SVP is busy. Please wait for a while, and then retry the operation. If the same problem persists despite retrying, call technical support. E 3 0002 7030 An error occurred during SVP processing. If this problem persists, please call technical support.
Part Code 0002 0002 Error Number Error Message Recommended Action 58578 An error occurred in the storage system. The configuration may be inconsistent. Please select [All Refresh] and refresh the configuration. 66100 The Login could not be performed because a function failed to start during SVP initialization. Please call technical support. Severity Level Failure Level Click [All Refresh] and refresh the configuration. E 2 Please call technical support.
Part Code 0003 0003 0003 0003 0003 0003 0003 26 Error Number Error Message Recommended Action Severity Level Failure Level Failed to remove the path. The specified path is the last path of the volumes used for Continuous Access, Business Copy, Cross-system Copy, Auto LUN, or XP Snapshot. Check the setting. E 6 1009 The emulation type of the volumes combined into a LUSE volume is not for open systems. The Configuration information has been already changed.
Part Code 0003 0003 0003 Error Number 1018 1020 1021 Error Message Recommended Action Severity Level Failure Level An error occurred. If this problem persists, please call technical support. The specified port does not exist. You have specified a wrong port number. Or the specified port type (exclusively for mainframe) cannot be processed in this agent. The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact technical support.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level The specified LU path does not exist. The Configuration information has been already changed. Please check the settings and request the setting of the configuration information again. E 6 The specified value of the command device setting is invalid. Check the setting. The specified value of the command device setting is invalid. (The specified value is not in the specification.
Part Code 0003 Error Number 1037 Error Message Recommended Action Severity Level Failure Level The free space remaining in the parity group is not enough to install a customized volume (CV). There is no capacity left in the logical parity group to create CV. The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact technical support.
Part Code 0003 Error Number 1049 Error Message Recommended Action An error occurred during SVP processing. If this problem persists, please call technical support. Severity Level Failure Level If this problem persists, call technical support. E 2 E 2 0003 1050 An error occurred. If this problem persists, please call technical support. Reserve volume of Auto LUN or Just in Time volume is included to a volume which links as an expanded LU.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level WWN number, which is not registered, is specified. (When deleting, or changing) The Configuration information has been already changed. Please check the settings and request the setting of the configuration information again. E 6 You are trying to register the same host group number as the already registered one. The Configuration information has been already changed.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Command device setting is requested for Reserve volume of Auto LUN/Just in Time volume. Or it is requested for volumes other than open volumes (including uninstalled volumes). The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact technical support.
Part Code 0003 0003 0003 0003 0003 0003 Error Number Error Message Recommended Action Severity Level Failure Level The command device setting and the command device security setting are incorrect. You cannot do any of the following to the same volume: • Specify the volume as a command device and disable command device security on the volume. • Specify the volume as a non-command device and enable command device security on the volume.
Part Code 0003 0003 0003 0003 0003 0003 0003 34 Error Number Error Message Recommended Action 1130 You cannot specify the default nickname when setting the nickname of a host group or a host. Severity Level Failure Level Correct the specified contents, and request again. E 6 1131 No more host groups can be set, because the number of host groups has reached the maximum (254) that can be set in a port.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level The Configuration information has been already changed. Please check the settings and request the setting of the configuration information again. E 6 0003 1137 Failed to form a LUSE volume because the number of LUSE volumes exceeds the maximum that can be set in a disk array subsystem. 0003 1138 An error occurred. If this problem persists, please call technical support. An error occurred.
Part Code Error Number Error Message Recommended Action 0003 1174 The specified host ID is already registered. 0003 1175 0003 Severity Level Failure Level Please correct the settings, then retry. E 6 Fibre port settings cannot be made to an iSCSI port. Please correct the settings, then retry. E 6 1176 High-speed mode cannot be set to iSCSI packages. Please correct the settings, then retry. E 6 0003 1177 The specified host is already registered.
Part Code Error Number Error Message Recommended Action 1192 When a path is defined from an iSCSI port to a volume, the volume cannot be configured as a command device. Also, paths cannot be defined from iSCSI ports to command devices. Severity Level Failure Level Please correct the settings, then retry. E 6 1193 You cannot add paths to Continuous Access/Business Copy/Cross-system Copy pair volumes. Please correct the settings, then retry.
Part Code Error Number 0003 1350 Error Message Recommended Action You could not add the path to the initiator or external port. Severity Level Failure Level To add a path, change the attribute of the specified port to Target or RCU Target. E 6 1351 The high-speed or initiator/external mix mode cannot be set to the specified port because of the attribute of the port.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Enable the Cache mode of this volume, then retry the operation, or remove the volume from the volumes to be set. E 2 0003 1359 Cache Residency Manager cannot be set for this volume because its Cache mode is set to Disable. 0003 1360 A Cross-system Copy volume cannot be defined as a system LU. Specify a volume that you can define as a system LU, then retry the operation.
Part Code Error Number Error Message Recommended Action 1604 The specified function is not available because it requires Cache Residency Manager. Severity Level Failure Level Please install the required program product. E 6 1613 Program products are not installed on the specified volume. Install the LUN Manager program product and the Open Volume Management program product. i 6 0003 1900 Maintenance operation is being executed by the SVP.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Correct the settings, then retry the operation. E 6 0003 1915 The specified LDEV number is invalid. The LDEV number of the CU group which is not set in CHA cannot be specified. 0003 1916 You cannot set the volumes in the same parity group across multiple CU groups. Correct the settings, then retry the operation. E 6 0003 1917 The volume(s) in CLPR cannot be set across multiple CU groups.
Part Code Error Number Error Message Recommended Action 2010 The LDEV is being used by the host, or an error occurred during SVP processing. Recovery processing may take about 1 minute. Please wait for a while. Severity Level Failure Level Check if the host is performing I/O operations on the target path or volume. E 6 2011 The status of the storage system requires maintenance (for example, the subsystem is blocked, the shared memory is inconsistent, or some other problem occurs).
Part Code 0003 0003 0003 0003 0003 0003 0003 0003 Error Number Error Message Recommended Action The current Cache Residency Manager setting cannot be changed because the prestaging operation is in progress. Please wait for a while, and then retry the operation. 2080 2081 Severity Level Failure Level Please wait a while, then retry the operation. E 6 Prestaging not completed. Wait a while, and click [Refresh], then change the same configuration again.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Take the storage system offline from the host. W 6 0003 2087 The system is online to the mainframe host. Take the subsystem offline from the host. 0003 2088 The Continuous Access pair is suspended. Add an alternative path. Add an alternative path. W 6 2089 The corresponding CHA might contain the last path between the MCU and RCU of Continuous Access. Make sure that there is an alternative path from the MCU.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Please wait for a moment and retry. E 6 0003 2095 A maintenance operation is in progress.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 2200 The Concurrent Copy or the HP StorageWorks XP for Compatible Extended Remote Copy (XRC) Software operation is in progress in the target volumes. Cancel the Concurrent Copy job or delete a Compatible XRC pair via the host. If the Concurrent Copy or the Compatible XRC operation is in progress in the target volumes, cancel the Concurrent Copy job or delete a Compatible XRC pair via the host.
Part Code 0003 0003 0003 0003 0003 0003 Error Number Error Message Recommended Action 2510 No path can be set to the specified volume because the addition of volumes is not finished. Severity Level Failure Level Please call technical support and finish adding volumes. E 6 2515 One of the following is defined: a Continuous Access pair, a HP StorageWorks XP Continuous Access Journal Software pair, or a Universal Replicator for Mainframe pair.
Part Code Error Number Error Message Recommended Action 0003 2520 An Auto LUN pair is defined. Cancel the pair definition, and then retry the operation. 0003 2521 Severity Level Failure Level Cancel the pair definition, then retry the operation. E 6 An Auto LUN pair is defined. Cancel the pair definition, cancel the reserve volume, and then retry the operation. Cancel the pair definition, cancel the reserve volume, then retry the operation. E 6 2522 An Auto LUN reserved volume is defined.
Table 5 Error Codes — Part Code 0004 Part Code Error Number Error Message Recommended Action 2006 An error occurred during SVP processing. If this problem persists, please call technical support. 0004 Severity Level Failure Level If this problem persists, call technical support. E 2 6000 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 0004 6001 A time-out error occurred.
Table 6 Error Codes — Part Code 0005 Part Code Error Number Error Message Recommended Action Severity Level Failure Level If this problem persists, call technical support. E 2 0005 5099 An error occurred during SVP processing. If this problem persists, please call technical support. 0005 5200 This functionality is not available. HP StorageWorks XP SNMP Agent is required. Install the program product. E 6 0005 5201 This functionality is not available. Parallel Access Volume is required.
Table 8 Error Codes — Part Code 0007 Part Code Error Number Error Message Recommended Action Severity Level Failure Level If this problem persists, call technical support. E 2 0007 5013 An error occurred during SVP processing. If this problem persists, please call technical support. 0007 5301 An error occurred. If this problem persists, please call technical support. An error occurred. If this problem persists, call technical support. E 2 5302 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action 0007 6092 An error occurred while reading a file. 0007 0007 Severity Level Failure Level Please call technical support. E 5 6093 The file to be downloaded was not found. The specified file was not found. Please check whether the file exists and retry the operation. W 5 56546 Another user is downloading the file. Please wait for a while, and then retry the operation. Please wait a while, then retry the operation.
Part Code Error Number Error Message Recommended Action 7060 0010 Severity Level Failure Level A client processing error occurred. Please delete the cache file of the browser, restart the browser and log on again. If this problem persists call technical support. E 2 7440 An error occurred during processing. If this problem persists please call technical support. An error occurred. If this problem persists, call technical support. E 2 0010 8101 The system cannot apply the new configuration.
Part Code Error Number Error Message Recommended Action 0010 59013 The specified file already exists. Do you want to overwrite this file? Severity Level Failure Level To overwrite the file, click [OK]. Otherwise, click [Cancel]. W 0 59109 The free space to store the audit log file has run out. The old audit log information is deleted because it is overwritten with the new audit log information. Please download the audit log file.
Part Code Error Number Error Message Recommended Action 2085 Copying is in progress for Continuous Access, Business Copy, ShadowImage for Mainframe, Auto LUN, Compatible FlashCopy, or Cross-system Copy pairs. Please wait for a while and then retry. 0105 Severity Level Failure Level Please wait a while, then retry. W 6 2086 The configuration of Continuous Access, Business Copy, ShadowImage for Mainframe, Auto LUN, Compatible FlashCopy, XP Snapshot, or Cross-system Copy has been defined.
Part Code 0105 0105 0105 Error Number Error Message Recommended Action 2093 Some Business Copy, ShadowImage for Mainframe, Compatible FlashCopy, or Cross-system Copy pairs exist. Please resynchronize them. Severity Level Failure Level Please resynchronize the Business Copy, ShadowImage for Mainframe, Compatible FlashCopy, or Cross-system Copy pairs. W 6 2094 Some Business Copy, ShadowImage for Mainframe, Compatible FlashCopy, or Cross-system Copy pairs exist.
Part Code 0105 0105 0105 0105 0105 0105 0105 0105 Error Number Error Message Recommended Action 2202 The specified volume cannot be processed due to the effect of the access attribute assigned by Volume Retention Manager. Check the settings, and then retry the operation. Severity Level Failure Level Check the settings, then retry the operation. E 6 2203 Processing cannot be performed because of HP StorageWorks XP Volume Security settings. Please correct settings, then retry.
Part Code Error Number Error Message Recommended Action 2518 A Business Copy, ShadowImage for Mainframe, Compatible FlashCopy, or Cross-system Copy pair is defined. Cancel the pair definition, and then retry the operation. If a reserve volume is defined, cancel it. If a high speed split is in progress, first suspend and then cancel the pair. 0105 Severity Level Failure Level Cancel the pair definition, then retry the operation. If a reserve volume is defined, cancel it.
Part Code Error Number Error Message Recommended Action 6023 An error occurred during SVP processing. If this problem persists, please call technical support. 0105 Severity Level Failure Level If this problem persists, call technical support. E 3 6533 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Please resynchronize or release the pair definition of the XP Snapshot pair using the pool volume to be maintained, then retry the operation. E 6 0105 58623 The specified operation cannot be performed, because the XP Snapshot pair using the pool volumes to be maintained is in PSUS status or being restored. Please resynchronize the pair or release the pair definition, and then retry the operation.
Part Code Error Message Recommended Action Severity Level Failure Level 5084 The evaluation license for this product (Remote Web Console) is not installed. Please install. Install Remote Web Console program product. i 5 5085 The maximum permissible capacity of program product became insufficient. Please install additional license key(s) to expand the license capacity of this software title. Please install additional license key(s) to expand the license capacity of this software title.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level W 5 i 5 i 0 0110 8201 The system detects an error. Retry the same operation several times. If the same error occurs, call technical support. 0110 9002 The requested operation is complete. Click [OK]. 0110 9100 Do you want to exit? 0110 9101 Do you want to cancel? To cancel, click [OK]. i 0 0110 9102 Do you want to apply? To execute the operation in Preview, click [OK], if not click [Cancel].
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Please wait for a while, then click [OK] and change the mode to Modify. W 0 0110 59002 The storage system is in internal process, or some other user is changing the configuration. Please wait for a while, then click [OK] and change the mode to Modify. Do you want to retry the operation to change the mode to Modify? 0110 59003 Succeeded to change the mode to Modify. Reply to the message.
Part Code Error Number Error Message Recommended Action 0190 5005 Enter the IP address. Input the IP address and retry. 0190 5006 Enter numerical values for the IP address. Input the IP address with the numerical value and retry. 0190 5007 Enter the location name. Input the location name and retry. 0190 5008 You cannot use the following characters: " \ , ; : * ? < >|/ Remove the invalid characters and retry. 0190 5009 You cannot use multi-byte characters.
Part Code Error Number Error Message Recommended Action 0190 5100 The files is compressing now. After completing FDCOPY which is booted last time, retry the operation. 0190 5110 Failed to compress the trace files. If the same error occurs again despite retrying, call technical support. 0190 5200 Security-file for download does not exist. Please call technical support. 0190 5210 The number of storage devices exceeds the maximum. You cannot register anymore.
Part Code Error Number Error Message Recommended Action 0190 6018 A permission error occurred. (Trace File Download Permission) Reboot the process. 0190 9000 Are you sure you want to register the storage device entry? None. 0190 9001 Are you sure you want to delete the selected storage device entry? None. 0190 9100 Are you sure you want to compress files? Reply to this message. 0190 57004 Specify both the certificate file and the key file.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 0210 55616 [New Password] does not match the re-entered [Re-enter New Password]. Specify a valid password. W 5 0210 55617 The specified user ID was deleted by the administrator. Specify another user ID. W 5 0210 55618 Authority of all administrator roles cannot be set to Disable. Check the settings. W 5 0210 55619 Authority of the account administrator role will be lost.
Part Code Error Number Error Message Recommended Action 0210 65637 Are you sure you want to disable the specified user? 0210 65638 Are you sure you want to enable the specified user? Severity Level Failure Level To disable the specified user, click [OK]. Otherwise, click [Cancel]. E 5 To enable the specified user, click [OK]. Otherwise, click [Cancel].
Part Code Error Number Error Message Recommended Action Check the settings. 0290 5102 The Status Window Hidden Option is specified but [NO] is not selected for the Polling period for checking obstacles Option. Are you sure you want to register the parameters? 0290 5103 Select [NO] for the Polling period for checking obstacles Option. Check the settings. 0290 5104 Status Window Hidden Option is specified. Select [No]. Check the settings.
Part Code Error Number Error Message Recommended Action 0290 6160 Failed to open the user account list file. If the same error occurs again despite retrying, call technical support. 0290 6170 Failed to open the user account list file. If the same error occurs again despite retrying, call technical support. 0290 6180 Failed to open the user account list file. If the same error occurs again despite retrying, call technical support. 0290 6190 Failed to open the environment file.
Part Code Error Number Error Message Recommended Action 0290 9002 Are you sure you want to register the parameters? None. 0290 9003 Are you sure you want to change the write permission? None. 0290 9004 Are you sure you want to change the password? None. 0290 9005 Are you sure you want to restore these files? Reply to this message. 0290 56111 File name is not specified. Specify the file name, then retry the operation. 0290 56121 File name is not specified.
Part Code Error Number Error Message Recommended Action 0290 56344 The size of the environment file is too large. Check the size of the file, decrease the size and retry the operation. 0290 56345 The size of the file is too large. Check the size of the file, decrease the size and retry the operation. 0290 56411 Failed to create the file. If this problem persists, call technical support. 0290 56421 Failed to create the file. If this problem persists, call technical support.
Part Code Error Number Error Message Recommended Action 7103 An error occurred during SVP processing. If this problem persists, please call technical support. 0305 Severity Level Failure Level If this problem persists, call technical support. E 2 7110 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 0305 7201 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action 0305 56525 Because the settings across the multiple SLPRs are contained, the authority has been shifted to the storage administrator from the storage partition administrator. To continue the operation, please contact the storage administrator. To perform other operations, select a function button. 0305 56526 The resources of other SLPR(s) cannot be accessed.
Part Code Error Number Error Message Recommended Action 0405 5071 Unable to install the license key. Temporary key installed. 0405 5072 The existing capacity of the licensed program product is invalid. Severity Level Failure Level Purchase the official license to use this software. W 5 Order the appropriate license that meets the requirement. W 5 Please install the related program product first.
Part Code 0405 Error Number 5077 Error Message Recommended Action To uninstall this program product, you must uninstall another program product first. Program Product Name Severity Level Failure Level To uninstall this program product, you should uninstall another program product first. W 5 To uninstall this program product, you should uninstall another program product first.
Part Code Error Number Error Message Continuous Access Asyn chronous Continuous Access Continuous Access Journal Continuous Access XP Snapshot Business Copy Performance Control Performance Monitor Auto LUN Performance Monitor Disaster Recovery Extended Universal Replicator for Mainframe Disaster Recovery Extended Continuous Access Journal Recommended Action Severity Level Failure Level 0405 5079 This program product needs another DKC type. Please call technical support.
Part Code Error Number Error Message Recommended Action 0405 5525 You cannot uninstall Data Retention Utility, because S-Vol disable remains. 0405 Severity Level Failure Level Remove the S-Vol disable setting. E 5 6012 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 0405 6022 The SVP is busy. Please wait for a while, and then retry the operation.
Part Code Error Number Error Message Recommended Action 7203 An error occurred during SVP processing. If this problem persists, please call technical support. 0405 Severity Level Failure Level If this problem persists, call technical support. E 2 7204 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 0405 7205 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action 8204 To use the program product, it needs to be enabled by installing additional shared memory. 0405 Severity Level Failure Level Install additional shared memory and enable the program product. E 2 8205 This program product remains in the configuration. Please call technical support. Please call technical support. E 2 0405 8206 This program product is in use, you cannot uninstall this program.
Part Code Error Message Recommended Action 57096 The number of licenses of a program product has exceeded the maximum which can be registered. 0405 0405 0405 0405 0405 0405 Error Number Severity Level Failure Level The maximum number of licenses which can be registered to a program product is 1,024. E 3 57097 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support.
Table 19 Error Codes — Part Code 0410 Part Code Error Number Error Message Recommended Action 0410 5030 The displayed information has not been changed. Try again. 0410 5045 0410 Severity Level Failure Level Specify what you register, and retry. W 0 The length of key codes is 20. Correct the specified content, and retry. W 5 5046 The maximum number of filename codes is 200. Correct the specified content, and retry.
Part Code Error Number Error Message Recommended Action 59305 Total of licensed capacities cannot be set to 0 by deleting all licensed capacities individually. 0410 Severity Level Failure Level Please set the licensed capacity so that the total will not become 0. To make the total 0, execute Uninstall. E 5 59306 The licensed capacity cannot be reduced because the specified amount of licensed capacity to be reduced exceeds the total capacity of the subsystem or the licensed capacity.
Part Code Error Number Error Message Recommended Action 6036 An error occurred during SVP processing. If this problem persists, please call technical support. 0505 0505 Severity Level Failure Level If this problem persists, call technical support. E 2 6040 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 6050 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action 8001 An error occurred while connecting to the subsystem. Please wait for a while, and then retry the operation. 0505 0505 Severity Level Failure Level Retry the same operation several times. If this problem persists, call technical support. E 2 8100 An error occurred while connecting to the subsystem. Please wait for a while, and then retry the operation. If the same problem persists despite retrying, please call technical support.
Table 22 Error Codes — Part Code 0510 Part Code Error Number 0510 0510 0510 Error Message Recommended Action 7060 An error occurred in the client logic. Severity Level Failure Level If this problem persists, please call HP technical support. E 2 59045 The detailed information will be initialized by this operation. Do you want to continue? To continue processing, click [OK]. To stop processing, click [Cancel].
Part Code Error Number Error Message Recommended Action 2086 Continuous Access, Business Copy, ShadowImage for Mainframe, Auto LUN or Compatible FlashCopy pair is defined. Release the pair definition, and then retry the operation. 0605 0605 Severity Level Failure Level Continuous Access, Business Copy, ShadowImage for Mainframe, Auto LUN or Compatible FlashCopy pair is defined. Release the pair definition, then retry the operation. W 3 2087 The system is online to the mainframe host.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Check the setting, then retry the operation. E 5 0605 2202 The specified volume cannot be processed due to the effect of the access attribute assigned by Volume Retention Manager. Check the settings, and then retry the operation. 0605 2203 Processing cannot be performed because of Volume Security settings. Processing cannot be performed because of Volume Security settings.
Part Code Error Number Error Message Recommended Action 2518 One of the following is defined: a Business Copy pair, a ShadowImage for Mainframe pair or a Compatible FlashCopy pair. Please split the pair and then retry the operation. If a reserve volume is defined, please cancel the reservation. When quick split is in process, suspend and then cancel the pair. 0605 Severity Level Failure Level Cancel the pair definition, then retry the operation. If a reserve volume is defined, cancel it.
Part Code Error Number Error Message Recommended Action 6022 An error occurred during SVP processing. If this problem persists, please call technical support. 0605 0605 Severity Level Failure Level If this problem persists, call technical support. E 3 6023 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 3 6502 Processing in progress. Please wait for a while, and then retry the operation.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level E 3 0605 8102 This function is not supported. Check whether the DKCMAIN microcode version and the SVP microcode version are mismatched. 0605 8122 This logical volume is busy. Please wait a while, then retry the operation. E 5 0605 8136 The command was rejected, because the licensed capacity was exceeded. The currently licensed capacity is insufficient.
Part Code Error Number Error Message Recommended Action 8959 An error occurred on the DKC side. If this problem persists, please call technical support. 0605 Severity Level Failure Level An error occurred on the DKC side. If this problem persists, call technical support. E 3 8960 An error occurred on the DKC side. If this problem persists, please call technical support. An error occurred on the DKC side. If this problem persists, call technical support.
Part Code Error Number Error Message Recommended Action 8971 An error occurred while connecting to the storage system. The configuration may be inconsistent. Click [Refresh All] on the File menu and refresh the configuration. Severity Level Failure Level An error occurred while connecting to the storage system. The configuration may be inconsistent. Click [Refresh All] on the File menu and refresh the configuration. E 2 8978 An error occurred on the DKC side.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Check the contents of the External Storage spreadsheet. E 5 0605 55319 The number of data items is invalid. (The definition sentence is not in the spreadsheet.) 0605 55340 There is no entry in an item that requires an entry. Check the contents of the External Storage spreadsheet. E 5 0605 55341 The number of digits is invalid. Check the contents of the External Storage spreadsheet.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Check the contents of the External Storage spreadsheet. E 5 0605 55375 The specified external volume group number is duplicated in the spreadsheet. 0605 55376 The specified external volume group number is already being used. Check the contents of the External Storage spreadsheet. E 5 0605 55377 An unset CLPR number has been specified. Check the contents of the External Storage spreadsheet.
Part Code Error Number Error Message Recommended Action 0605 55391 An unsupported device was specified. 0605 55392 0605 Severity Level Failure Level Check the contents of the External Storage spreadsheet. E 5 The specified SSID value is already being used. Check the contents of the External Storage spreadsheet. E 5 55393 There is an error in the path settings. Check the contents of the External Storage spreadsheet. E 5 56301 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action 56516 The configuration of Continuous Access is defined. Reset the configuration definition of Continuous Access, and then retry the operation. Severity Level Failure Level Reset the configuration definition of Continuous Access, then retry the operation. E 5 56517 The configuration of Business Copy, ShadowImage for Mainframe, Compatible FlashCopy or XP Snapshot is defined.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level E 5 0605 58246 This function is not supported. Check whether the DKCMAIN microcode version and the SVP microcode version are mismatched. 0605 58258 All the paths to the external volume are blocked. Restore the blocked path status, then retry the operation. E 5 0605 58263 No paths will be available, if you change the setting of paths.
Part Code 0605 0605 0605 0605 0605 0605 0605 0605 0605 Error Number Error Message Recommended Action 58573 Severity Level Failure Level This function is not supported. Check whether the DKCMAIN microcode version and the SVP microcode version are mismatched. E 3 58575 An error occurred while connecting to the subsystem. Please wait for a while, and then retry the operation. If this problem persists, call technical support.
Part Code Error Number Error Message Recommended Action 66013 The specified emulation type cannot be set because 3390-3R is set in the subsystem. Severity Level Failure Level Change the emulation type set in the volume. E 5 66014 The specified emulation type cannot be set because 3390-3 is set in the subsystem. Change the emulation type set in the volume. E 5 66015 The specified path configuration cannot be applied. Check the status of the path, then retry the operation.
Table 24 Error Codes — Part Code 0610 Part Code Error Number Error Message Recommended Action 0610 6505 The number of LUs that can be set to the external volume group exceeds the maximum (4096). 0610 6516 Severity Level Failure Level Please decrease the Volumes that are set to the external volume group, then retry the operation. W 0 R-VOLs exist on the RCU port. Please release the R-VOLs that have been set. W 5 7060 An error occurred during processing.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Click [OK]. i 0 0610 59020 The setting is insufficient for automatic mapping. Check the setting, and then retry the operation. 0610 59021 The automatic mapping processing was interrupted. Retry the operation. i 0 0610 59022 There are not enough logical volumes to perform the mapping operation. Decrease the number of external volumes to be mapped, then retry the operation.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Please correct the licensed capacity with the License Key Partition Definition window. W 5 0610 59057 The licensed capacity was exceeded because of changing the configuration. Please correct the licensed capacity on the License Key Partition Definition window. 0610 59058 Do you want to specify an SSID without restrictions on SLPRs? To continue processing, click [OK]. Otherwise, click [Cancel].
Part Code 0610 0610 0610 0610 0610 Error Number Error Message Recommended Action 69005 Either the emulation types or the SLPR numbers or the both for the multiple external volumes you selected are not the same. When selecting multiple volumes, select the volumes that have the same emulation type and the same SLPR number. Severity Level Failure Level When selecting multiple volumes, select the volumes that have the same emulation type and the same SLPR number.
Part Code 0610 0610 Error Number Error Message Recommended Action 69026 The selected volumes include an external volume that the external volume parameter is already set. Set the configuration in the following [External Volume Parameter] dialog box. 69027 A CLPR number cannot be applied for [Set External Volume Parameter] dialog box or [Edit Policy] dialog box is specified. Severity Level Failure Level Check all items in the [Set External Volume Parameter] dialog box and click [OK].
Part Code Error Number Error Message Recommended Action Severity Level Failure Level You are trying to set multiple paths to the same volume from one group. The Configuration information has been already changed. Please check the settings and request the setting of the configuration information again. E 6 1004 Multiple volumes are specified to a single port, group or LUN combination. The Configuration information has been already changed.
Part Code 1005 1005 1005 1005 1005 1005 Error Number 1013 1015 1018 1020 1021 1022 Error Message Recommended Action Severity Level Failure Level The emulation types of the volumes combined into a LUSE volume are not the same. The emulation type of a volume which links as an expanded LU is not the same. The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact technical support.
Part Code Error Number 1005 1023 1005 1005 1024 1025 Error Message Recommended Action An error occurred. If this problem persists, please call technical support. Severity Level Failure Level If this problem persists, call technical support. E 2 An error occurred. If this problem persists, please call technical support. Fibre topology information is invalid. (The specified value is not in the specification.) The error does not occur normally because it is guarded in the screen.
Part Code Error Number Error Message Recommended Action 1064 You are trying to register the same WWN as the already registered one. Please check the settings and request the setting of the configuration information again. 1065 Severity Level Failure Level The Configuration information has been already changed. Please check the settings and request the setting of the configuration information again. E 6 The specified host name or the host group name is already registered.
Part Code 1005 1005 1005 1005 1005 1005 1005 110 Error Number Error Message Recommended Action Severity Level Failure Level An error occurred. If this problem persists, please call technical support. A nickname is not specified when the configuration change of LUN Manager is requested. The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact technical support. E 2 An error occurred.
Part Code 1005 1005 1005 1005 1005 1005 1005 Error Number Error Message Recommended Action 1130 You cannot specify the default nickname when setting the nickname of a host group or a host. Severity Level Failure Level Correct the specified contents, and request again. E 6 1131 No more host groups can be set, because the number of host groups has reached the maximum (254) that can be set in a port.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level The Configuration information has been already changed. Please check the settings and request the setting of the configuration information again. E 6 1005 1137 Failed to form a LUSE volume because the number of LUSE volumes exceeds the maximum that can be set in a disk array subsystem. 1005 1138 An error occurred. If this problem persists, please call technical support. An error occurred.
Part Code Error Number Error Message Recommended Action You are trying to insert in the linkage operation including LUSE. (LDEV number is inserted to the LDEV numbers created in LUSE). Severity Level Failure Level The Configuration information has been already changed. Please check the settings and request the setting of the configuration information again. E 6 1186 In the linkage operation including LUSE, the path is specified to other than the top.
Part Code Error Number Error Message Recommended Action 1203 High Speed mode/MIX mode was specified. However, there are addresses to which High Speed mode/MIX mode cannot be set in the Fibre Addresses of the specified ports. 1005 1005 Severity Level Failure Level The Configuration information has been already changed. Please check the settings and request the setting of the configuration information again. E 6 1204 High Speed mode/MIX mode was specified.
Part Code Error Number Error Message Recommended Action 1356 You could not add the host group to the initiator or external port. 1005 1005 Severity Level Failure Level To add the host group, change the attribute of the specified port to Target or RCU Target. E 6 1357 S-VOLs remain on the Fibre-RCU port. This operation may cause a fatal damage to the S-VOLs. Please stop this operation. If you want to continue this operation, please remove the S-VOLs from the RCU port first.
Part Code Error Message Recommended Action Severity Level Failure Level 1904 The specified volume cannot be assigned as a LUSE volume or a command device, and the path of the volume cannot be set because it is being used as a Pool volume. Select another volume. E 6 1905 There are virtual volumes and non-virtual volumes in the volumes specified to compose a LUSE volume. Select another volume.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 1005 2032 Communication busy. Please retry later. Please retry later. E 3 2082 Processing is disabled because the host is mounted or the device is reserved. The host is mounted or the device is reserved. Please unmount the host and cancel reservation of the device. If the host is an AIX host, unmount the host, and execute the varyoffvg command. E 6 2083 The subsystem status is invalid.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Please correct settings, then retry. E 6 1005 2503 The LUs cannot be combined or released because the volumes don't have Read/Write attribute. 1005 2504 No settings can be made because of a volume reserved for RAID Manager. Release the reserve setting of the volume, then retry the operation. W 5 3002 An error occurred during SVP processing. If this problem persists, please call technical support.
Part Code Error Number Error Message Recommended Action 6050 An error occurred during SVP processing. If this problem persists, please call technical support. 1005 Severity Level Failure Level If this problem persists, call technical support. E 2 7060 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 1005 8001 An error occurred while connecting to the subsystem.
Part Code Error Message Recommended Action Severity Level Failure Level 55560 The fibre address, topology, channel speed, and Initiator/Target cannot be changed because the specified port is an iSCSI port. Check the setting. E 6 1005 55561 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 1005 55566 An error occurred during SVP processing.
Part Code 1005 1005 1005 1005 1005 1005 1005 1005 1005 1005 1005 Error Number Error Message Recommended Action 56302 An error occurred during SVP processing. If this problem persists, please call technical support. Severity Level Failure Level If this problem persists, call technical support. E 2 56303 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support.
Table 28 Error Codes — Part Code 1010 Part Code Error Number Error Message Recommended Action 1023 The specified fibre address is invalid. 1010 1010 Severity Level Failure Level Correct the specified content, and issue the request again. (Currently, Bad Value Send report in Set Response.) W 5 1065 The specified host group is already used. Correct the specified contents, and request the setting of the configuration information again.
Part Code Error Number Error Message Recommended Action 5071 Path setup cannot be performed because the copy source is not an open-system volume. 1010 Severity Level Failure Level Please follow the correct operation procedure. W 5 5099 The specified LUN is the last path to the command device. Release the command device. Check the content of the operation. W 5 1010 5822 You entered the wrong item. Correct the settings, then retry. W 5 1010 5823 It is not updated.
Part Code Error Number Error Message 1010 9151 Only the LUN(LDEV) is specified. Select the corresponding LDEV(LUN). 1010 55208 The host mode External Storage cannot be specified. 1010 55233 1010 Severity Level Failure Level i 0 Check the settings. W 5 The host mode External Storage cannot be specified. Check the settings. W 5 55234 This action will cause a failover of resource groups on the node which is going to be shutdown if they are running.
Part Code Error Number Error Message Recommended Action 1110 You can not use the following characters for the name: \/,: ;*"<>| You cannot use spaces for the first and the last characters in the name. 1110 Severity Level Failure Level Remove the prohibited characters from the nickname. W 5 5000 The specified WWN is invalid. Please specify the WWN with 16 characters, using any of the following combinations: • Numerals (0-9), • Letters (A-F), • Hyphen (-), or • Space.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Check the content of the operation. W 5 1110 5053 The system cannot move the host. Specified name already exists in the destination. 1110 5054 You cannot drop the host onto a port if the security switch is OFF. Check the content of the operation. W 5 1110 5056 The system cannot add the LUN to the LUN group in the mapping window. Check the content of the operation.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level • colons (:) 1110 5825 You cannot drop the host onto a host group. Follow the correct operation procedure. W 5 1110 7060 An error occurred in the client logic. Please call technical support. E 2 9010 All the hosts connected to the target port can access only the LUNs defined in group #00. Therefore, the file system may become corrupt while the LUNs defined in all other groups are inaccessible.
Part Code Error Number Error Message Recommended Action 1110 9080 Are you sure to clear the selected group #00? To continue processing, click [Yes]. To stop processing, click [No]. 1110 9100 There are different security settings in the group. Do you want to re-configure? 1110 9101 There are groups or that don't members. apply? 1110 9102 Do you want to renew the security as group? 1110 55006 The configuration will not take effect until you turn on the security switch.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Correct the settings, then retry the operation. W 5 1110 55546 The specified Target alias is incorrect. Please specify the Target alias within 32 characters. The characters can be any combinations of the following: • numerals (0-9) • letters from A to Z, a to z • dots (.) • hyphens (-) • colons (:) 1110 55547 The specified Target alias is already being used. Click [OK].
Part Code 1205 1205 Error Number Error Message Recommended Action 8001 8966 Severity Level Failure Level A communication time-out error occurred. Please retry the operation. If the problem persists, reboot the computer. If necessary, Please call technical support. E 3 An error occurred on the DKC side. If this problem persists, please call technical support. An error occurred on the DKC side. If this problem persists, call technical support. E 3 W 5 1205 56298 The SVP is busy.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Retry the operation after the microcode is replaced. E 5 1205 58390 Microcode is being replaced in the storage system. Please retry the operation after the microcode is replaced. 1205 58391 The specified port is blocked. If the same problem persists despite retrying, call technical support. E 5 1205 58392 The port is in Link Down status. Please check the status of cable connection.
Part Code Error Number Error Message Recommended Action 1310 55602 The specified authentication interval is invalid. 1310 55603 1310 59310 Severity Level Failure Level Correct the settings, then retry the operation. W 0 The specified number of times of authentication is invalid. Correct the settings, then retry the operation. W 0 The authentication switch will be changed. Do you want to continue? To change the authentication switch, click [OK]. Otherwise, click [Cancel].
Part Code Error Number Error Message Recommended Action 2010 7060 An error occurred in the client logic. Please call technical support. Severity Level Failure Level E 2 9010 The specified volumes will be expanded to LUSE volume. All data in each LDEV will be initialized. Do you want to continue? i 0 2010 9060 The specified LUSE volume will be released. All data in the volume will be initialized. Do you want to continue? i 0 2010 9100 The LUSE volume needs at least one path.
Table 33 Error Codes — Part Code 3005 Part Code Error Number Error Message Recommended Action 3005 1910 The specified volume contains XP Snapshot pair. 3005 1911 Severity Level Failure Level Check the setting of the specified volumes. E 6 The specified volumes contain Pool-VOLs. Check the setting of the specified volumes. E 6 2011 The status of the storage system requires maintenance (for example, the system is blocked, the shared memory is inconsistent, or some other factor).
Part Code 3005 3005 3005 3005 3005 3005 Error Number Error Message Recommended Action 2091 The backup server of Business Copy, ShadowImage for Mainframe, or Compatible FlashCopy is running. Please stop the backup server and then retry the operation. Severity Level Failure Level Please stop the backup server and then retry the operation. W 6 2092 Some Business Copy, ShadowImage for Mainframe, or Compatible FlashCopy pairs exist. Please split them.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level means of the TERMSESS command. 2201 Processing cannot be performed because of Data Retention Utility settings. Check the settings, then retry the operation. E 6 3005 2202 The specified volume cannot be processed due to the effect of the access attribute assigned by Volume Retention Manager. Check the settings, then retry the operation.
Part Code 3005 3005 3005 3005 3005 3005 3005 3005 Error Number Error Message Recommended Action 2516 One of the following is defined: a Continuous Access pair, a Continuous Access Journal pair, or a Universal Replicator for Mainframe pair. Please delete the pair definition or suspend the pair, and then retry the operation. Severity Level Failure Level Please delete the pair definition or suspend the pair, and then retry the operation.
Part Code Error Number Error Message Recommended Action 5010 An error occurred during SVP processing. If this problem persists, please call technical support. 3005 Severity Level Failure Level If this problem persists, call technical support. E 2 5013 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 3005 5099 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action 6533 An error occurred during SVP processing. If this problem persists, please call technical support. 3005 Severity Level Failure Level If this problem persists, call technical support. E 3 7060 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 3050 7111 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action 55506 An error occurred during SVP processing. If this problem persists, please call technical support. Severity Level Failure Level If this problem persists, call technical support. E 2 55507 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 55508 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action 55519 An error occurred during SVP processing. If this problem persists, please call technical support. Severity Level Failure Level If this problem persists, call technical support. E 2 55594 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 56301 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Restore the blockade status of the logical volume. E 6 3005 58461 The specified operation cannot be done, because the logical volume is blocked. 3005 58462 The logical volume cannot be registered, because it is defined as a Pool-VOL. Specify another logical volume.
Part Code Error Number Error Message Recommended Action 3005 58472 Operation of the pool has failed. Pool cannot be registered when: • V-VOL management area is not initialized. • V-VOL management area is not installed. • there is no space left in the V-VOL management area. • the pool is blocked. • the state of shared memory is abnormal. Pool cannot be deleted when: • V-VOL management area is not initialized. • V-VOL management area is not installed. • XP Snapshot pair still remains in the pool.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level E 6 3005 58474 The capacity of shared memory is insufficient or an error occurred during SVP processing. Please check the amount of free space in Pool management block in the Pool window. Please install additional shared memory if the free space is insufficient. Please call technical support if the capacity of shared memory is not insufficient. 3005 58475 The PCB for fibre port or iSCSI port is not installed.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Please resynchronize the pair or release the pair definition, then retry the operation. E 6 3005 58623 The specified operation cannot be performed, because the XP Snapshot pair using the pool volumes to be maintained is in PSUS status or being restored. Please resynchronize the pair or release the pair definition, then retry the operation. 3005 58626 An XP Snapshot pair is defined.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Please wait a while, then retry the operation. E 6 3005 68727 Shared memory is being initialized. Please wait a while, then retry the operation. 3005 68728 The pool is in an abnormal state. Recover the pool, then retry the operation. Recover the pool, then retry the operation. E 6 3005 68729 LDEV format is being executed in the specified volume.
Part Code Error Number Error Message Recommended Action 5054 Execute one of the following before deleting the LDEV: However, LDEV cannot be deleted for the Remote Command Device.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Enter the correct value. W 5 3010 5060 The setting capacity in the VLL operation is outside the setting range. Set the capacity within the specified range. 3010 5061 Set the number of cylinders used for VLL operation to 50 cylinders or more. Enter the correct value. W 5 3010 5062 LDEV Creation failed because the specified capacity was invalid. Enter the correct value.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 3010 9102 Do you want to apply? To execute the operation in Preview, click [OK]. i 0 3010 9103 Do you want to change? i 0 3010 9150 Specify the SSID. i 0 3010 55026 The MakeVolume operation will be performed while the number of volumes in the parity group is zero. Click [OK]. W 0 3010 55030 There is a volume that has not been divided into volumes of the same size. ( - %d [Block]) Click [OK].
Part Code Error Message Recommended Action Severity Level Failure Level 55635 Neither the format processing nor the shredding processing is executed. Click [OK]. W 5 55637 The processing for adding or deleting LDEV remains interrupted. Please call technical support and request to execute the interrupted processing and end the processing normally from the SVP. Request technical support to execute the interrupted processing and complete it successfully from the SVP.
Part Code Error Number 3010 3010 3010 3010 3010 3010 Error Message Recommended Action 65641 Cannot reset because the LDEV number is used in another VDEV. Severity Level Failure Level Release the LDEV number already set, then reset. W 5 65642 Install CV cannot be operated anymore because the number of LDEVs has exceeded the maximum number that can be set in the VDEV. Reduce the number of LDEVs in the VDED, then retry the install CV operation.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level minutes or less. Do you want to continue? 3110 59312 Do you want to continue discard the changed setting and processing it? Select [OK] to continue processing, or select [Cancel] to stop processing. W 5 3110 59601 It will be added to the Pool-VOL table with the specified contents. Do you want to continue? To continue processing, click [OK]. Otherwise, click [Cancel].
Part Code Error Number Error Message Recommended Action 3205 2088 The Continuous Access pair is suspended. Please add an alternate path. Severity Level Failure Level Please add an alternate path. W 5 2089 The corresponding CHA might contain the last path between the MCU and RCU of Continuous Access. Make sure that there is an alternative path from the MCU. Be sure there is an alternative path from the MCU.
Part Code Error Number Error Message Recommended Action 6012 An error occurred during SVP processing. If this problem persists, please call technical support. 3205 Severity Level Failure Level If this problem persists, call technical support. E 3 6022 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 3 3205 6023 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action 8952 An error occurred on the DKC side. If this problem persists, please call technical support. 3205 Severity Level Failure Level An error occurred on the DKC side. If this problem persists, call technical support. E 3 8953 An error occurred on the DKC side. If this problem persists, please call technical support. An error occurred on the DKC side. If this problem persists, call technical support.
Part Code Error Number Error Message Recommended Action 8965 An error occurred on the DKC side. If this problem persists, please call technical support. 3205 Severity Level Failure Level An error occurred on the DKC side. If this problem persists, call technical support. E 3 8966 An error occurred on the DKC side. If this problem persists, please call technical support. An error occurred on the DKC side. If this problem persists, call technical support.
Part Code 3205 3205 3205 Error Number Error Message Recommended Action 56517 The Business Copy, ShadowImage for Mainframe, Compatible FlashCopy, or XP Snapshot setting exists. Release the setting and then retry the operation. Severity Level Failure Level Release the setting of Business Copy, Business Copy for Mainframe, Compatible FlashCopy, or XP Snapshot, then retry the operation.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level • The specified capacity exceeds the remaining capacity. 3210 55301 There are V-VOLs whose CU:LDEV numbers are not set. Check the settings, and retry the operation. W 5 3210 55302 The selected CU:LDEV number has already been used. Check the specified content, and retry the operation. W 5 3210 55303 The CU:LDEV number is outside the valid range. Check the specified content, and retry the operation.
Table 38 Error Codes — Part Code 3305 Part Code Error Number Error Message Recommended Action 1035 An error occurred during SVP processing. If this problem persists, please call technical support. 1036 Severity Level Failure Level If this problem persists, call technical support. E 2 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support.
Part Code Error Number Error Message Recommended Action 1075 An error occurred during SVP processing. If this problem persists, please call technical support. 3305 Severity Level Failure Level If this problem persists, call technical support. E 2 1101 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support.
Part Code Error Message Recommended Action Severity Level Failure Level 1913 The setting cannot be made because the specified LDEV is a remote command device. Check the setting. E 6 3305 1914 The number of V-VOL(s) has exceeded the maximum number of V-VOL(s) that can be set in a storage system. Correct the settings, then retry the operation. E 6 3305 1919 The newly added LDEV has not been formatted. Check the blocked LDEV and format the LDEV. Check the blocked LDEV and format the LDEV.
Part Code Error Message Recommended Action 2086 The configuration of Continuous Access, Business Copy, ShadowImage for Mainframe, Auto LUN, Compatible FlashCopy, or XP Snapshot has been defined. Reset the configuration definition, and then retry the operation. 3305 3305 3305 3305 3305 3305 3305 3305 3305 162 Error Number Severity Level Failure Level The configuration of Continuous Access, Business Copy, ShadowImage for Mainframe, Auto LUN, Compatible FlashCopy, or XP Snapshot has been defined.
Part Code Error Message Recommended Action 2095 A maintenance operation is in progress. For example: • LDEV formatting is in progress • Correction Copy is in progress • Drive Copy is in progress • The CHA/DKA status is changing • The cache status is changing • Replacement of an OEM drive microcode is in progress • LDEV shredding is in progress Therefore the specified operation cannot be executed.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level by Business Continuity Manager, and then retry the operation. 2516 One of the following is defined: a Continuous Access pair, a Continuous Access Journal pair, or a Universal Replicator for Mainframe pair. Please release the pair definition or suspend the pair, then retry the operation. Please release the pair definition or suspend the pair, then retry the operation.
Part Code Error Number Error Message Recommended Action 3002 An error occurred during SVP processing. If this problem persists, please call technical support. 3305 Severity Level Failure Level If this problem persists, call technical support. E 2 3003 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 3305 3006 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action 3305 65650 The specified volume is used as a System Disk volume. 3305 3305 3305 3305 3305 Severity Level Failure Level Check the setting of the specified volume. E 6 65651 The number of volumes with System Disk setting exceeds the maximum number of volumes defined as System Disk volume. Check the setting. E 6 65661 There are no changes in the current configuration and the setting. Check the setting.
Part Code Error Number Error Message Recommended Action 6001 An error occurred during SVP processing. If this problem persists, please call technical support. 4005 Severity Level Failure Level If this problem persists, call technical support. E 2 6011 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 4005 6012 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action 55244 The Cache Residency Manager size set for the CLPR exceeds the maximum available Cache Residency Manager size. CLPR No:%s SLPR No:%s Severity Level Failure Level Check the settings, then retry the operation. E 6 55245 The number of Cache Residency Manager areas set for the CLPR exceeds the maximum available number of Cache Residency Manager areas. CLPR No:%s SLPR No:%s Check the settings, then retry the operation.
Part Code Error Number Error Message Recommended Action 55534 An error occurred during SVP processing. If this problem persists, please call technical support. 4005 Severity Level Failure Level If this problem persists, call technical support. E 2 55535 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 4005 55536 An error occurred during SVP processing.
Part Code 4005 Error Number 58512 Error Message Recommended Action The current Cache Residency Manager setting cannot be changed because the prestaging operation is in progress. Please wait for a while, and then retry the operation. Severity Level Failure Level Please wait a while, then retry the operation. E 6 E 6 4005 58513 Prestaging not completed. Wait a while, refresh the window, then retry the configuration operation.
Part Code Error Number Error Message Recommended Action 2080 4010 4010 Severity Level Failure Level Prestaging not completed. Wait a while, click [Refresh], and change the same configuration again. Or if the DKC status is not blocked, check the DKC status. If the same error occurs, call technical support. E 6 5010 The value specified as the ending address for the data to be placed in cache is smaller than the value specified as the starting address.
Table 41 Error Codes — Part Code 4105 Part Code Error Number Error Message Recommended Action 4105 1603 This functionality is not available. Cache Residency Manager is required. 4105 6012 4105 Severity Level Failure Level Install the necessary program product. E 6 An error occurred during server processing. If this problem persists, please call technical support. An error occurred during SVP processing. If this problem persists, call technical support.
Part Code Error Number 4105 4105 4105 4105 Error Message Recommended Action 56526 The resources of other SLPR(s) cannot be accessed. Severity Level Failure Level Correct the settings, then retry the operation. E 6 57007 The sum of the maximum values of the PCR capacity per CLPR does not match the maximum value of total PCR capacity. Check the settings, and retry the operation. E 6 57008 The maximum value of PCR capacity per the specified CLPR is not multiples of 512MB.
Part Code Error Number Error Message Recommended Action 5013 An error occurred during SVP processing. If this problem persists, please call technical support. 5105 Severity Level Failure Level If this problem persists, call technical support. E 2 5099 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support.
Part Code Error Number Error Message Recommended Action 7111 An error occurred during SVP processing. If this problem persists, please call technical support. 5105 Severity Level Failure Level If this problem persists, call technical support. E 2 7428 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 5105 8002 The subsystem status is invalid. Please call technical support.
Part Code Error Number Error Message Recommended Action 5105 56526 The resources of other SLPR(s) cannot be accessed. 5105 66016 A monitoring switch cannot be enabled with the specified gathering interval. Severity Level Failure Level Correct the settings, then retry the operation. E 6 Change the gathering interval, and retry the operation.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Release the Cache Residency Manager setting. E 6 5205 1079 The volume specified as the reserved volume has the Cache Residency Manager settings. 5205 1080 The reserved volume(s) cannot be used. Retry the same operation. If nothing changes, call technical support. E 6 5205 1081 The specified volume(s) are used as a command device. Release the command device, or select another volume.
Part Code Error Number Error Message Recommended Action 5205 1121 The volume(s) is already being used by Compatible XRC. 5205 1122 5205 Severity Level Failure Level Retry the same operation. If nothing changes, call technical support. E 6 The volume(s) is already being used by Compatible XRC. Retry the same operation. If nothing changes, call technical support. E 6 1207 The volume types do not match. Retry the same operation. If nothing changes, call technical support.
Part Code Error Number Error Message Recommended Action 5205 1221 The volume(s) are already used by Auto LUN. 5205 Severity Level Failure Level Retry the same operation. If nothing changes, call technical support. E 6 1222 The number of the Business Copy, ShadowImage for Mainframe, or Compatible FlashCopy pair volumes exceeds the maximum. Please release the Business Copy/Compatible FlashCopy pair. E 6 5205 1223 The volume(s) are already used by Auto LUN. Retry the same operation.
Part Code Error Number Error Message Recommended Action 5205 1235 The target volume(s) is already being used by Continuous Access. 5205 1236 Severity Level Failure Level Retry the same operation. If nothing changes, call technical support. E 6 The RAID level of the target volume is not supported. Retry the same operation. If nothing changes, call technical support. E 6 1237 The specified volume(s) are already used by Business Copy, ShadowImage for Mainframe, or Compatible FlashCopy.
Part Code Error Number Error Message Recommended Action 1251 The specified target volume is connected to iSCSI port. 5205 Severity Level Failure Level Re-execute the same operation. If the problem persists, call technical support. E 6 1252 The volume specified as a reserved volume is connected to iSCSI port. Re-execute the same operation. If the problem persists, call technical support. E 6 5205 1253 The specified volume cannot be used because the volume is being used by Cross-system Copy.
Part Code Error Number Error Message Recommended Action 5205 2011 The storage system is busy. Please wait for a while, and then retry the operation. 5205 2024 5205 Severity Level Failure Level Please Release the Continuous Access Pair. E 6 The controller detected the blockade location. Please call technical support. E 6 2025 The controller detected the blockade location. Please call technical support. E 6 5205 2026 The controller detected the blockade location.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 5205 5507 The specified volume is not defined as the target volume of Auto LUN. Please try again. E 6 5205 6000 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 6001 An error occurred during SVP processing. If this problem persists, please call technical support.
Part Code Error Number Error Message Recommended Action 7401 Failed to get information from hihsmpln.ini. The file may not exist in the specified directory. Severity Level Failure Level Retry the same operation several times. If the same error occurs, call technical support. E 6 7402 Failed to get information from hihsmfpg.ini. The file may not exist in the specified directory. Retry the same operation several times. If the same error occurs, call technical support.
Part Code Error Number Error Message Recommended Action 7414 The file (hihsmpgr.ini） contains invalid data. 5205 Severity Level Failure Level Retry the same operation several times. If the same error occurs, call technical support. E 6 7415 The file (hihsmcls.ini） contains invalid data. Retry the same operation several times. If the same error occurs, call technical support. E 6 5205 7416 The file (hihsmpgr.ini） contains invalid data. Retry the same operation several times.
Part Code Error Number Error Message Recommended Action Retry the same operation several times. If the same error occurs, call technical support. Severity Level Failure Level E 6 E 6 5205 8001 An error occurred while connecting to the subsystem. Please wait for a while, and then retry the operation. 5205 8100 This function is not supported. 5205 8102 This function is not supported. Retry the same operation several times. If the same error occurs, call technical support.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Check the setting of the migration source volume and the migration target volume. E 6 5205 55201 If the migration source volume is a normal volume, a CVS volume of the same capacity as the migration source volume cannot be specified as the migration target volume.
Part Code Error Number Error Message Recommended Action 55254 The specified source volume is an external volume that belongs to a Cross-system Copy pair. The specified target volume is an internal volume. Therefore, the specified volumes cannot be used for migration. Severity Level Failure Level Check the source volume setting and the target volume setting. E 6 55255 The specified source volume is an external volume that belongs to a Cross-system Copy pair.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level If this problem persists, call technical support. E 2 5205 55500 An error occurred during SVP processing. If this problem persists, please call technical support. 5205 55521 The specified volume(s) are already being used as XP Snapshot volume(s). Select another volume. E 6 5205 55522 The specified volume(s) are already being used as V-VOL(s). Select another volume.
Part Code Error Number Error Message Recommended Action 55586 The specified volume cannot be migrated because an extent in the volume is being shredded. 5205 5205 Severity Level Failure Level Please check the setting of the specified volume. E 6 55592 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 55593 An error occurred during SVP processing.
Part Code 5205 5205 Error Number Error Message Recommended Action 65673 The specified volume(s) are already being used as of XP Thin Provisioning volume (TP-VOL) (s). 65674 The specified volume(s) are already being used as of XP Thin Provisioning volume (TP-VOL) (s). Severity Level Failure Level Check the setting of the specified volume. E 6 Check the setting of the specified volume.
Table 46 Error Codes — Part Code 5305 Part Code Error Number Error Message Recommended Action Severity Level Failure Level Correct the specified contents, and request the setting of the configuration information again. E 6 5305 1064 The specified WWN is already being used. 5305 1258 This port is not properly equipped. Retry the same operation. If nothing changes, call technical support. E 6 5305 2002 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action 5305 5104 The specified Performance Control group is already registered. 5305 5105 5305 Severity Level Failure Level Check the specified content, and retry. W 6 The target port(s) does not equip the monitored WWN(s). Check the specified content, and retry. W 6 5106 The target WWN is already registered in the port. Check the specified content, and retry. W 6 5305 5107 The specified Name is already used.
Part Code Error Number Error Message Recommended Action 6036 An error occurred during SVP processing. If this problem persists, please call technical support. 5305 Severity Level Failure Level If the same error occurs despite retrying, call technical support. E 2 6050 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 5305 6051 An error occurred during processing.
Part Code 5305 Error Number 56302 Error Message Recommended Action Severity Level Failure Level An error occurred during SVP processing. If this problem persists, please call technical support. The error may be caused by a temporary communication failure. Reboot the SVP or click [Refresh All] on the File menu of Remote Web Console and refresh the configuration information to recover from the error. If this problem persists, call technical support.
Part Code 5305 5305 5305 5305 5305 196 Error Number Error Message Recommended Action Severity Level Failure Level 58572 An error occurred while connecting to the subsystem. Please wait for a while, and then retry the operation. The error may be caused by a temporary communication failure. Reboot the SVP or click [Refresh All] on the File menu of Remote Web Console and refresh the configuration information to recover from the error. If this problem persists, call technical support.
Table 47 Error Codes — Part Code 5307 Part Code Error Number Error Message Recommended Action 5307 5102 The specified Performance Control group is not registered. 5128 The number Performance exceeds the number that registered. Severity Level Failure Level Check the specified content, and retry. W 6 Check the specified content, and retry.
Part Code Error Message Recommended Action Severity Level Failure Level 5111 The number of the WWNs exceeds the maximum number that can be registered on an Performance Control group. Check the specified content, and retry. i 5 5310 5128 The number Performance exceeds the number that registered. Check the specified content, and retry. i 5 5310 5129 The WWN is already registered in another Performance Control group. Check the specified content, and retry.
Part Code Error Number Error Message Recommended Action 5310 9313 The control status will change to WWN Control. 5310 9314 5310 5310 Severity Level Failure Level The control status will change to WWN Control. Please click [OK]. W 5 There is no control, because the upper value is 0 in all ports. Please set up a maximum value to control. W 5 9315 The monitoring switch is turned OFF. If you use the real time option for the first time, turn ON the monitoring switch.
Table 49 Error Codes — Part Code 6005 Part Code Error Number Error Message Recommended Action 5013 An error occurred during SVP processing. If this problem persists, please call technical support. 6005 Severity Level Failure Level If this problem persists, call technical support. E 2 5099 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support.
Part Code 6005 6005 6005 6005 6005 6005 6005 6005 Error Number Error Message Recommended Action Severity Level Failure Level Logical Path between the MCU and the RCU is not active. A logical path does not exist between the MCU and the RCU. Check the path status on RCU Status screen, and reestablish the paths with Edit Path. i 4 8702 The pair status of the M-VOL is not valid. The type of pair status is not permitted for this operation. Refresh and check the screen.
Part Code 6005 6005 Error Number Error Message Recommended Action 8710 The pair status of the specified volume is not valid. 8711 Parameter specified by Continuous Access operation for expansion volume is not valid. Severity Level Failure Level The pair status does not permit this operation. Verify the pair status, and if the operation is permitted retry. i 4 Check the port number, GID, and LUN of the RCU. i 4 The operation was rejected due to a FREEZE state.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level E 4 6005 8719 Invalid RCU serial number, SSID, Link Address or Controller ID. Check the serial number, SSID, link address and controller ID of the RCU, and set the correct value. Then retry the operation. If the same error occurs, contact technical support. 6005 8720 Too many RCUs. (Four RCUs are the maximum) A maximum of four RCUs are permitted, and that many already exist.
Part Code 6005 Error Number 8731 Error Message Recommended Action Severity Level Failure Level The existing logical addresses are not equal. The logical addresses of all existing paths are not the same. Delete the RCU, then re-add it, using the same logical address as other existing paths. i 4 E 4 6005 8732 Too many SSIDs (Only Four SSIDs are allowed). The maximum number of SSIDs (four) has been entered. Verify that the SSIDs are valid, delete one or more, then retry the operation.
Part Code Error Number 6005 8743 6005 6005 6005 6005 Error Message Recommended Action Pinned track(s) exists on the R-VOL. 8744 8745 8746 8747 Severity Level Failure Level Check the status of the R-VOL tracks, and clear the pinned tracks. W 4 The specified M-VOL condition is not valid for Continuous Access. The M-VOL is not available for the requested operation, because of one or more of the following reasons: 1. The volume is blocked. 2. The volume is under maintenance. 3.
Part Code Error Number Error Message Recommended Action Specified M-VOL may be in use by HOST. 8749 6005 Severity Level Failure Level Data migration cannot start because the volume is online. Please vary the path offline and retry. i 4 Specified R-VOL is still online from HOST. Please check if the input number of R-VOL is correct. If not, enter the correct R-VOL number. If the number is correct, vary the specified path offline.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level R-VOL Device Cache status is not active. Check the device cache status of R-VOL from host. If it is off, set it on and retry. If it cannot be set on, call technical support. i 4 R-VOL DFW status is not active. Check the DFW status of the R-VOL from the host. If it is off, set it on and retry. If it cannot be set on, call technical support.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level E 4 6005 8772 Change pair operation failed due to communication error or the R-VOL status is invalid. The pair option change operation failed, either because a communication error occurred or because the R-VOL status is not valid. Please verify the status. Also view the License Key window at the RCU side and check the licensed capacity for Volume Retention Manager.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level The Continuous Access option must be installed in the MCU and RCU before a Continuous Access volume pair can be created. i 4 6005 8781 TrueCopy for Mainframe function is not installed in the specified controller. 6005 8785 The M-VOL is defined as the expansion volume. Please recheck the volume. i 4 6005 8786 The R-VOL is defined as the expansion volume. Please recheck the volume.
Part Code Error Number Error Message Recommended Action 8795 The operation failed because the specified M-VOL was one of the following: • A T-VOL of ShadowImage for Mainframe and not in the Split pair(PSUS) status. • An S-VOL of Business Copy and not in the Split pair (PSUS) status. • A reserved volume of ShadowImage for Mainframe or Business Copy. • A volume in the Reverse Copy status of ShadowImage for Mainframe or Business Copy. • A T-VOL of Compatible FlashCopy.
Part Code Error Number 6005 6005 6005 6005 6005 6005 6005 6005 Error Message Recommended Action 8800 The R-VOL is already in use for Auto LUN. 8801 8802 8803 8804 8805 8806 8807 Severity Level Failure Level Verify the status of the specified R-VOL. E 4 The R-VOL is reserved, or the RCU or the path between MCU-RCU is in a heavy load condition. Verify the status of the specified R-VOL. If the device is not reserved, retry the operation. i 4 CT group is not active.
Part Code 6005 Error Number 8808 Error Message Recommended Action Severity Level Failure Level Please retry Add Pair (Paircreate)/Resume Pair (Pairresync) operation in a few minutes. The add/resume pair operation failed, because the either the specified volume or another volume in the same group is being changed to simplex or suspend status. Retry the operation after the status change is completed. i 4 Add/resume pair operation failed.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level W 4 • it is a reserved volume of Business Copy or ShadowImage for Mainframe. • it is a volume reserved by Auto LUN. • it is used by Universal Replicator for Mainframe. 6005 8820 The specified R-VOL is not a permissible condition of Continuous Access. The Continuous Access operation failed, because R-VOL has one of the following conditions: 1. The volume is blocked. 2. The volume is under maintenance. 3.
Part Code Error Number Error Message Recommended Action 6005 8830 The specified M-VOL is already used as a reserved volume of Auto LUN. 6005 8831 Severity Level Failure Level Check the status of the specified M-VOL (P-VOL) from HOST or SVP. i 4 The specified R-VOL is already used as a reserved volume of Auto LUN. Check the status of the specified R-VOL (S-VOL) from HOST or SVP. i 4 8832 Please wait a few minutes and retry the Add Pair (Paircreate) / Resume Pair (Pairresync) operation.
Part Code 6005 Error Number 8843 Error Message Recommended Action Severity Level Failure Level Suspend(Pairsplit-r) operation failed because specified volume or other volume in the same group is not in permissible status. The operation failed, because of one of the following reasons: 1. The specified volume is simplex. 2. There is no duplex or duplex-pending volume in the group. 3. Either the specified volume or another volume in the same group is suspended. Verify the status, and retry the operation.
Part Code Error Number 6005 8852 6005 6005 6005 6005 216 Error Message Recommended Action Severity Level Failure Level R-VOL status change failed after M-VOL status change. Confirm R-VOL status. Confirm the R-VOL status. E 4 Delete Pair (Pairsplit-S) operation failed because M-VOL is in Simplex (SMPL) status. The operation failed, because of one of the following reasons: 1. The specified volume is simplex. 2. There is no duplex, duplex-pending, or suspend volume in the group.
Part Code Error Number Error Message Recommended Action 8858 6005 Severity Level Failure Level All volumes were not deleted by the Delete Pair (Pairsplit-S) operation. The operation failed for all of the volumes, because either the pair status of the volume is SEQCHK or the consistency time of the volume does not match the consistency time of the CT group. Verify the status of the failed volumes. If necessary, retry the Delete Pair operation with the volume or the group option.
Part Code Error Number Error Message Recommended Action 8870 CT Group Option cannot be changed unless all asynchronous pairs in the group are suspended or deleted. 6005 Severity Level Failure Level The group operation failed because the specified group has at least one asynchronous pair. Renew and check the Continuous Access screen. i 4 8871 The TrueCopy Asynchronous for Mainframe function is not installed in the specified MCU.
Part Code Error Number Error Message Recommended Action 6005 8888 An internal error occurred. 6005 8889 6005 Severity Level Failure Level Please call technical support. E 4 The specified port is not equipped. Refresh the screen, and retry. If nothing changes, call technical support. E 4 8890 The specified port is being initialized. Please wait until the initialization of the port ends, and retry the operation. E 4 6005 8891 Logical paths exist on the MCU port.
Part Code 6005 6005 6005 Error Number 8904 8905 8906 Error Message Recommended Action Severity Level Failure Level No more space is left in MCU for differential management. If the extended shared memory (SM #2) is not installed in MCU, install the shared memory to MCU according to the installation instruction of the extended shared memory for remote copy (Shared Memory Size Configuration dialog box), then create a pair.
Part Code 6005 Error Number 8911 Error Message Recommended Action Severity Level Failure Level Logical paths exist on the port. The Remote Console computer detected a logical path (z/OS) on the port. Please delete the path(s) and retry the operation. i 4 i 4 6005 8912 Logical paths exist on the port. The Remote Console computer detected a logical path (z/OS) on the port. Please delete the path(s) and retry the operation. 6005 8913 Invalid port type.
Part Code Error Number Error Message Recommended Action 6005 8926 The specified R-VOL is prohibited to use by Volume Security. 6005 8927 6005 Severity Level Failure Level Confirm the status of Volume Security of the specified R-VOL. E 4 The specified M-VOL is prohibited to use by Volume Security. Confirm the status of Volume Security of the specified M-VOL. E 4 8929 Invalid port type. Please check the port status and retry. W 4 6005 8930 Logical paths exist on the RCU port.
Part Code Error Number Error Message Recommended Action 8943 The specified volume or other volume(s) of the same group in the RCU is being changed to Simplex/Suspend status. Retry the operation a few minutes later. 8944 Severity Level Failure Level Refresh the window a few minutes later and check the status of the specified volume and other volume(s) of the same group in the RCU. If it is possible to perform operations on the volume(s), retry the operation.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6005 8977 A pair cannot be created, because the specified R-VOL is an external volume. Check the status of the specified R-VOL. i 4 6005 8980 The operation failed because the licensed capacity of Volume Retention Manager on the RCU side was exceeded. Confirm the licensed capacity Volume Retention Manager on the RCU side. To execute this operation, purchase a license key that allows you to use a larger capacity.
Part Code Error Number Error Message Recommended Action 6005 56524 This function cannot be used by the storage partition administrator. Severity Level Failure Level Select another window. To set this function, contact the storage administrator. E 3 57005 An error occurred during SVP processing. If this problem persists, please call technical support. Please call technical support.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level A pair cannot be created because the licensed capacity of Data Retention Utility on the RCU side is insufficient or Data Retention Utility is not installed on the RCU. Check the licensed capacity of Data Retention Utility on the RCU side or confirm whether Data Retention Utility is installed on the RCU.
Part Code 6005 6005 6005 6005 6005 6005 6005 6005 Error Number Error Message Recommended Action Severity Level Failure Level 58498 A pair cannot be created because the specified M-VOL is being used as a pool volume. Please specify another volume. i 5 58499 A pair cannot be created because the specified R-VOL is being used as a pool volume. Please specify another volume. i 5 58509 A communication time-out error occurred between MCU and RCU.
Part Code 6005 6005 6005 6005 228 Error Number Error Message Recommended Action 58713 The licensed capacity of Continuous Access Asynchronous or TrueCopy Asynchronous for Mainframe on the RCU is insufficient. Check the licensed capacity of this program product and the related program products.
Part Code 6005 6005 6005 6005 6005 Error Number Error Message Recommended Action 68012 A pair cannot be created because the specified R-VOL is being used as an XP Thin Provisioning volume. Severity Level Failure Level Check whether the specified R-VOL is an XP Thin Provisioning volume. W 0 68020 "Maximum Initial Copy Activities (CU)" cannot be changed to Enable or Disable, because there are pairs in COPY or Pending status.
Part Code Error Number 6007 6007 6007 6007 Error Message Recommended Action 6023 The SVP is busy. Please wait for a while, and then retry the operation. Severity Level Failure Level If the same problem persists despite retrying, call technical support. E 3 6024 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 6036 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action 5066 The RCU and one of the CT group channel types do not match. Please correct RCU or CT group. 6010 Severity Level Failure Level Select the same path type for RCU and CT group. W 5 5131 The combination of parameters which you specified is not permitted. Please specify a valid combination of parameters. Check the condition for setting parameter, and re-execute the setting. i 5 6010 5137 The Operation value is invalid.
Part Code Error Number Error Message Recommended Action 8928 An error occurred when copying started. 6010 Severity Level Failure Level Please suspend the specified pair, and perform the operation to resume the pair. W 0 9006 Exchange the channel cable connections after confirmation of the port type. Please follow the instructions in the message. W 5 6010 9007 Please confirm that the R-VOLs to specify are varied off-line. Please confirm that the R-VOLs to specify are varied off-line.
Part Code Error Number Error Message Recommended Action 6010 9072 Are you sure you want to delete the specified volume pairs? 6010 9073 6010 Severity Level Failure Level To delete the specified pair, click [OK]. Otherwise, click [Cancel]. i 0 Are you sure you want to suspend the specified volume pairs? To suspend the specified pair, click [OK]. Otherwise, click [Cancel]. i 0 9074 Are you sure you want to erase data on the R-VOL? To delete the contents of the remote volume, click [OK].
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6010 9115 The monitoring was stopped by another operator. The graph will be closed. Click [OK]. i 0 6010 9116 Another operator has changed the Gathering Interval value. The graph will be closed. Click [OK]. i 0 6010 9117 Are you sure you want to close the graph? To close the graph, click [OK]. Otherwise, click [Cancel]. i 0 6010 9118 Please check the specified value.
Part Code Error Number Error Message Recommended Action 9154 As a result of this operation, you will not be able to re-start ERASE R-VOL operation. To delete the pair forcibly, please try again with Force option. Severity Level Failure Level Please follow the instructions in the message. W 0 9155 The history file has been updated. Select the OK button to display the history logs from the beginning. Click [OK].
Part Code Error Number Error Message Recommended Action 9308 You set the same path more than once. The duplicate paths are excluded. Severity Level Failure Level Since there were overlapped paths in the added paths, the overlapped paths were eliminated. Click [OK] and continue. W 0 9309 All paths which you set have already been registered. This operation will terminate because there is no path which can be added.
Part Code Error Number Error Message Recommended Action 9360 The specified value exceeds the range. Alternatively, the relationship between the specified values is not appropriate. Severity Level Failure Level Check the specified values and retry the operation. W 5 55035 If you plan to create a pair with the specified LUSE volumes, a DKC path is required. Select Add RCU command, then register a DKC path.
Part Code 6010 Error Number 59030 Error Message Recommended Action Severity Level Failure Level The monitoring data saved at present will be deleted. To continue the operation, click [OK]. To cancel the operation, click [Cancel]. The monitoring data currently saved will be deleted if you change the setting of the monitoring switch. If necessary, use the Performance Monitor Export Tool to export the monitoring data file. i 5 To continue processing, click [OK]. To stop processing, click [Cancel].
Table 52 Error Codes — Part Code 6105 Part Code Error Number 6105 56524 Error Message Recommended Action This function cannot be used by the storage partition administrator. Select another window. To set this function, contact the storage administrator. Severity Level Failure Level E 3 Severity Level Failure Level Table 53 Error Codes — Part Code 6505 Part Code Error Message Recommended Action 3003 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action 6505 7310 This error code is not registered. Severity Level Failure Level If the same error occurs despite retrying, call technical support. E 5 8000 An error occurred during SVP processing. If this problem persists, please call technical support. Retry the operation. If this problem persists, call technical support. E 3 8001 A communication time-out error occurred in the subsystem.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Please refresh the window, then check the pair status. If possible, retry the operation on the secondary data volume. i 4 6505 8708 The pair status of the secondary data volume is incorrect. 6505 8709 Continuous Access operation was rejected. Please replace the channel adapter, then retry the operation. E 4 6505 8710 The pair status of the specified data volume is incorrect.
Part Code 6505 6505 6505 6505 Error Number Error Message Recommended Action 8722 Severity Level Failure Level Path creation failed. Check the path connections between the local and the remote storage systems, then retry the operation. E 4 8723 The Edit Path operation was rejected because the specified path is the last path of some Continuous Access pairs. Add another path, or delete all pairs on the remote storage system. Then retry the operation.
Part Code 6505 6505 6505 Error Number 8733 8734 8735 Error Message Recommended Action Severity Level Failure Level Continuous Access Journal or Universal Replicator for Mainframe is not installed in the subsystem. Continuous Access Journal or Universal Replicator for Mainframe must be installed in the storage system when you create a path or a pair for Continuous Access Journal or Universal Replicator for Mainframe.
Part Code 6505 6505 6505 6505 244 Error Number 8744 8745 8746 8749 Error Message Recommended Action Severity Level Failure Level The specified primary data volume cannot be used. Check whether the primary data volume is in any of the following conditions: • Data in the primary data volume is being copied; correction copy or drive copy is in progress. • The primary data volume is in correction access condition. • The primary data volume is blocked.
Part Code Error Number Error Message Recommended Action 6505 8753 An internal error occurred. 6505 6505 Severity Level Failure Level Please check the SSB log, then call technical support. E 4 8757 One side of the cache is blocked in the primary subsystem. Check the status of the cache in the primary storage system. Ensure that the cache is not blocked, then retry the operation. W 4 8758 An unexpected error occurred in the primary subsystem. Please call technical support.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Mainframe T-VOL in non-Split status. • The volume was a reserved volume. • The volume was in the Reverse Copy status. 8796 The operation failed because the specified secondary data volume was one of the following: • An S-VOL or reserved volume of Business Copy. • A T-VOL or reserved volume of ShadowImage for Mainframe. • A T-VOL of Compatible FlashCopy. • A Business Copy volume in the Reverse Copy status.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level i 4 6505 8831 The specified secondary data volume is already reserved by Auto LUN. Volumes reserved by Auto LUN cannot be specified as secondary data volumes. Check the status of the specified secondary data volume from the host or the SVP. 6505 8832 Please wait a few minutes and then retry the operation. Wait a few minutes and retry the operation.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 8898 Pending data exists on the port. Retry the operation. i 4 6505 8899 An internal error occurred. Please check the SSB log, then call technical support. E 4 6505 8900 An error occurred during the port change. Please call technical support. E 4 6505 8901 An error occurred during the port change. Please call technical support. E 4 6505 8902 An error occurred during the port change.
Part Code Error Number Error Message Recommended Action 8936 The Paircreate (Add Pair) operation failed. The microcode version of the specified secondary subsystem does not support Continuous Access with NAS volumes. 6505 Severity Level Failure Level Please check the microcode version of the secondary storage system. W 0 8944 The specified secondary data volume is unusable because of the access attribute changed by Data Retention Utility.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 58008 The command was rejected by the subsystem because the command is unknown. Please call technical support. i 0 6505 58009 No more remote subsystems can be registered. Reduce the number of registered remote storage systems, then retry the operation. i 0 6505 58010 Invalid parameter (path group ID). Check the specified path group ID.
Part Code Error Number Error Message Recommended Action 58026 The specified threshold for ending creation of asynchronous journal is invalid. 6505 Severity Level Failure Level Check the threshold for ending creation of asynchronous journal. i 0 58027 The specified threshold for ending creation of synchronous journal is invalid. Check the threshold for ending creation of synchronous journal. i 0 6505 58028 The specified threshold for starting creation of asynchronous journal is invalid.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 58039 The specified volume is already used as a journal volume or a data volume. Specify another volume. i 0 6505 58040 An internal error occurred. Please check the SSB log, then call technical support. E 4 6505 58064 Too many requests. Please reduce the number of requests to be processed at one time. After that, please retry the operation.
Part Code Error Number Error Message Recommended Action 58079 The specified primary data volume cannot be used as an S-VOL (secondary volume) because of Volume Retention Manager settings or Data Retention Utility settings. Severity Level Failure Level Check the status of the specified primary data volume in the Volume Retention Manager window or the Data Retention Utility window. i 0 58080 A Concurrent Copy operation is in progress on the specified primary data volume.
Part Code Error Message Recommended Action Severity Level Failure Level 58088 The specified mirror ID differs from the registered mirror ID. Please check the combination of the primary journal group and the mirror ID. Check the specified mirror ID. i 0 58089 No more remote subsystems can be registered. Reduce the number of registered remote storage systems, then retry the operation.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 6505 58101 The pair status is incorrect. Refresh the window, and check the pair status. i 0 6505 58102 An internal error occurred. Please check the SSB log, then call technical support. E 4 6505 58103 The specified secondary data volume is a reserve volume of a mainframe host. Check the status of the specified secondary data volume from the mainframe host.
Part Code Error Number Error Message Recommended Action The Add Pair (Paircreate) operation failed because of either of the following reasons. • The specified restore journal group has already been paired with another master journal group. • The combination of the restore journal group and the mirror ID specified when creating Delta resync volume pairs has already been used by the ordinary (not Delta resync) volume pairs.
Part Code Error Number Error Message Recommended Action 58276 The specified secondary data volumes cannot be paired with another volume, because the secondary data volume is used as a journal volume. 6505 6505 Severity Level Failure Level Check the status of the specified secondary data volume. i 0 58277 The specified secondary data volume is not registered in the specified journal group. Check data volumes in the specified secondary journal group.
Part Code Error Message Recommended Action Severity Level Failure Level 58285 No more pairs can be registered because the number of pairs will exceed the maximum. Check the number of pairs. i 0 58286 The command was rejected because the command was issued to the primary data volume. The command is supposed to be issued to the secondary data volume. Check the command parameters. i 0 6505 58287 The command was rejected because the command was issued to the secondary data volume.
Part Code Error Number Error Message Recommended Action 6505 58295 An internal error occurred. 6505 6505 58296 58297 Severity Level Failure Level Please call technical support. E 4 The specified volume is used by another program product.
Part Code Error Number Error Message Recommended Action 6505 58308 The specified primary data volume is used as a command device. Severity Level Failure Level Please check the configuration of the primary data volume. W 0 58323 The Add Pair (Paircreate) operation failed because the specified primary data volume was being used by Continuous Access Asynchronous or TrueCopy Asynchronous for Mainframe. Please specify another primary data volume, and retry the operation.
Part Code 6505 6505 6505 6505 6505 6505 6505 6505 6505 Error Number Error Message Recommended Action 58329 The Add Pair (Paircreate) operation or the Resume Pair (Pairresync) operation cannot be performed because the journal cache for the master journal group is not empty and contains data. Severity Level Failure Level Please call technical support. W 0 58333 Because the specified journal group is a restore journal group, the parameter related to the inflow cannot be changed.
Part Code 6505 6505 6505 6505 6505 6505 6505 6505 6505 262 Error Number Error Message Recommended Action 58342 The specified volume cannot be used as a journal volume because of a Data Retention Utility setting or a Volume Retention Manager setting. Severity Level Failure Level Please check the setting of the volume in the Data Retention Utility window or the Volume Retention Manager window.
Part Code 6505 6505 6505 Error Number Error Message Recommended Action The Add Pair (Paircreate) operation failed because the specified secondary data volume was one of the following: • An S-VOL of Business Copy. • A T-VOL of ShadowImage for Mainframe or Compatible FlashCopy. • A reserved volume of Business Copy or ShadowImage for Mainframe. • A P-VOL of Business Copy in Swap or Reverse Copy status. • An S-VOL of ShadowImage for Mainframe in Swap or Reverse Copy status.
Part Code Error Number 6505 6505 6505 6505 6505 6505 6505 6505 6505 264 Error Message Recommended Action 58451 The storage system is in internal process. Please retry the operation. Severity Level Failure Level If the problem persists despite retrying, call technical support. W 0 58455 The Add Pair operation or the Resume Pair operation failed because the specified primary data volume was a T-VOL of Compatible FlashCopy.
Part Code 6505 6505 6505 6505 6505 6505 6505 Error Number Error Message Recommended Action Severity Level Failure Level 58490 Only the pair option of the primary data volume was updated. Failed to update the pair option of the secondary data volume. A communication error between the primary and the secondary storage systems occurred, or the microcode of the secondary storage system does not support the change pair option function.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Check the mirror ID assigned to the specified primary data volume number (LDKC:CU:LDEV) from the secondary storage system, and assign a mirror ID that is not used, and retry the operation. W 0 6505 58510 The Add Pair (Paircreate) operation failed. The combination of the specified primary data volume number (LDKC:CU:LDEV) and the mirror ID is the same as the combination specified from another primary subsystem.
Part Code 6505 6505 6505 6505 6505 6505 6505 Error Number Error Message Recommended Action 58561 The Add Pair operation or the Resume Pair operation failed because the timer type of the master journal group was different from the timer type of the restore journal group. Severity Level Failure Level Please check the timer type of the master journal group and the restore journal group. W 0 58562 The specified volumes or the volumes in the specified journal group were deleted.
Part Code 6505 6505 6505 6505 6505 6505 6505 6505 268 Error Number Error Message Recommended Action 58591 The Add Pair (Paircreate) operation or the Resume Pair (Pairresync) operation failed because the journal volumes of the specified restore journal group were blocked. Severity Level Failure Level Check the status of the journal volumes of the specified restore journal group. W 0 58592 The specified operation failed because the subsystem was being powered on or powered off.
Part Code 6505 6505 6505 6505 6505 6505 6505 6505 6505 6505 Error Number Error Message Recommended Action 58601 Journal groups cannot be added to the extended consistency group (EXCTG), because the additional shared memory was not installed. Severity Level Failure Level Please call technical support and install additional shared memory. W 0 58602 Journal groups cannot be added to the extended consistency group (EXCTG), because the number of subsystems in the EXCTG exceeds the maximum.
Part Code Error Message Recommended Action 58611 The specified operation failed because the microcode exchange was in progress on the subsystem in the extended consistency group (EXCTG). 6505 6505 6505 6505 6505 6505 6505 6505 6505 6505 270 Error Number Severity Level Failure Level Retry the operation after the microcode exchange completes. W 0 58612 The previously executed update processing of the extended consistency group (EXCTG) has not completed.
Part Code 6505 6505 6505 6505 6505 6505 6505 Error Number Error Message Recommended Action 58624 Journal groups cannot be added to the extended consistency group (EXCTG), because the combination of the serial number and the command device is invalid. Severity Level Failure Level Check whether the specified command device of the specified serial number exists.
Part Code Error Number Error Message Severity Level Failure Level 58685 Delta resync operation failed because the specified primary data volume was not a data volume of Continuous Access Synchronous or TrueCopy for Mainframe Synchronous, or the pair status of the primary data volume was invalid. Check the following of the specified primary data volume.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 58691 The specified mirror ID is already used in the restore journal group. Specify another mirror ID. Specify another mirror ID. W 0 58692 The specified master journal group cannot be used for Delta resync because the specified master journal group is registered in the extended consistency group (EXCTG). Check the status of the master journal group.
Part Code 6505 6505 6505 6505 6505 6505 274 Error Number Error Message Recommended Action 58698 The Add Pair (Paircreate) operation failed because the specified secondary data volume was used by Delta resync. Severity Level Failure Level Check the status of the secondary data volume. W 0 58699 The Add Pair (Paircreate) operation to get ready for Delta resync failed because the specified secondary data volume was used by one of the following program products.
Part Code 6505 6505 6505 6505 6505 Error Number Error Message Recommended Action 58704 The Add Pair (Paircreate) operation to get ready for Delta resync failed because the status of the volumes was one of the following: • The P-VOL for Continuous Access Synchronous and the primary data volume for Continuous Access Journal are different. • The M-VOL for TrueCopy for Mainframe Synchronous and the primary data volume for Universal Replicator for Mainframe are different.
Part Code 6505 6505 6505 276 Error Number Error Message Recommended Action 58717 The licensed capacity of Continuous Access Asynchronous or TrueCopy Asynchronous for Mainframe on the RCU is insufficient. Check the licensed capacity of this program product and the related program products.
Part Code 6505 6505 6505 6505 6505 6505 Error Number Error Message Recommended Action 58720 The licensed capacity of Continuous Access Asynchronous or TrueCopy Asynchronous for Mainframe on the MCU is insufficient. Check the licensed capacity of this program product and the related program products.
Part Code Error Number Error Message Recommended Action 68007 The Add Pair (Paircreate) operation failed. The LDKC number of the specified secondary data volume is different from the LDKC number of the specified restore journal group. Severity Level Failure Level Confirm that the LDKC number of the secondary data volume and the LDKC number of the restore journal group is the same.
Part Code 6505 6505 6505 6505 Error Number Error Message Recommended Action 68019 The secondary subsystem does not support the LDEV number of the specified primary data volume. Severity Level Failure Level Check whether the secondary subsystem supports the LDEV number of the specified primary data volume. W 0 68024 The Add Pair(Paircreate) operation failed because the current microcode version does not support Delta Resync. Check the microcode version of the connected storage system.
Table 55 Error Codes — Part Code 6510 Part Code Error Number Error Message Recommended Action 6510 5030 The displayed information has not been changed. 6510 5137 6510 Severity Level Failure Level Specify the data that you want to register in the SVP. Then retry the operation. W 0 The Operation value is invalid. Specify the correct value. Check the contents, and retry. W 0 5138 The value specified for Gathering Interval is invalid. Specify a valid value within the range of 1 to 15.
Part Code Error Number Error Message Recommended Action 9024 Are you sure you want to exchange the specified ports? Please confirm the associated channel paths are off-line. Severity Level Failure Level Please ensure that the associated channel paths are offline. W 5 9025 Are you sure you want to switch the ports? If the remote copy paths exist on the ports, delete them beforehand. Please remove remote copy paths associated with the ports.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Click [OK]. i 0 6510 9116 Another operator has changed the Gathering Interval value. The graph will be closed. 6510 9117 Are you sure you want to close the graph? To close the graph, click [OK]. If not click [Cancel]. i 0 6510 9118 Please check the specified value. To apply this setting, click [OK]. To change the setting, click [Cancel]. i 0 6510 9119 No graph item has been selected.
Part Code Error Message Recommended Action 9309 All paths which you set have already been registered. This operation will terminate because there is no path which can be added. 6510 6510 6510 6510 Error Number Severity Level Failure Level Since all the added paths are redundant, the paths cannot be added. Click [OK] and continue. W 0 9327 The monitoring time is over, but the history file is not fully updated yet. Click [Refresh] to update the history file.
Part Code Error Number Error Message Recommended Action 56504 No journal group with the same CLPR number as the specified volume is registered. Please register a journal group that has the same CLPR number as the specified volume, and then retry the operation. Severity Level Failure Level Please register a journal group that has the same CLPR number as the specified volume, then retry the operation. i 0 56505 There are no secondary subsystems available.
Part Code Error Number 6510 59026 6510 6510 6510 6510 6510 6510 6510 Error Message Recommended Action Severity Level Failure Level The same DKC is specified more than once. Check the DKC setting. Check the DKC setting. W 0 The monitoring data saved at present will be deleted. To continue the operation, click [OK]. To cancel the operation, click [Cancel]. The current monitoring data will be deleted if you change the setting of the monitoring switch.
Part Code 6510 6510 6510 6510 6510 Error Number Error Message Recommended Action The specified parity group does not contain volumes that can be registered or deleted as journal volumes. 59108 Severity Level Failure Level Please specify another parity group. W 0 The master journal group number for the specified data volume exceeds 0x0F. Please check the master journal group number for the specified data volume.
Part Code Error Number Error Message Recommended Action 59153 The journal volume cannot be deleted because the status of the mirror of the journal group is Active. Severity Level Failure Level Change the status of the mirror of the journal group to Stop or Initial, then retry the operation. W 0 59323 The entered parameter is invalid. The serial number, the controller ID or the journal group to be added is not specified. Check the entered parameter.
Part Code Error Message Recommended Action Severity Level Failure Level 65664 The specified volume is not valid for this program product. Specify another volume. Specify another volume. W 0 6510 65665 The specified volume is not the volume to be monitored. Check the monitoring setting. Check the monitoring setting. W 0 6510 69016 Are you sure you want to cancel the export? To stop the operation, click [OK]. To continue the operation, click [Cancel].
Part Code Error Number Error Message Recommended Action 6610 5140 The specified CU number is incorrect. Specify the correct CU number. 6610 5141 6610 Severity Level Failure Level Specify the correct CU number. W 0 The specified LDEV number is incorrect. Specify the correct LDEV number. Specify the correct device number. W 0 5144 Some of the entered values are incorrect. Check the values and then specify correct values. Check the values, then specify correct values.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level To continue to change ports, click [OK]. W 5 6610 9026 Are you sure you want to switch the ports? If any remote copy paths exist on the ports, delete them beforehand. Also, to avoid the switching operation from being reported as a failure, confirm first that a message prompting you to change the channel cable connections is displayed, and then perform the necessary changes.
Part Code Error Number Error Message Recommended Action 6610 9117 Are you sure you want to close the graph? 6610 9118 6610 Severity Level Failure Level To close the graph, click [OK]. Otherwise, click [Cancel]. i 0 Please check the specified value. To apply this setting, click [OK]. To change the setting, click [Cancel]. i 0 9119 No graph item has been selected. Please select a graph item. Select a graph item. i 0 9120 The graph will be closed if you execute the processing.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Click [Refresh] to update the history file. If this problem persists, call technical support. i 0 6610 9327 The monitoring time is over, but the history file is not fully updated yet. 6610 9332 This operation is not applied yet. Click [OK], then continue the operation. i 0 55036 Too many data volumes in the journal group. Check the number of data volumes in the journal group.
Part Code Error Number Error Message Recommended Action 56504 No journal group with the same CLPR number as the specified volume is registered. Please register a journal group that has the same CLPR number as the specified volume, and then retry the operation. Severity Level Failure Level Please register a journal group that has the same CLPR number as the specified volume, then retry the operation. i 0 56505 There are no secondary subsystems available.
Part Code Error Number 6610 59026 6610 6610 6610 6610 294 Error Message Recommended Action Severity Level Failure Level The same DKC is specified more than once. Check the DKC setting. Check the DKC setting. W 0 The monitoring data saved at present will be deleted. To continue the operation, click [OK]. To cancel the operation, click [Cancel]. The current monitoring data will be deleted if you change the setting of the monitoring switch.
Part Code Error Number Error Message Recommended Action 59042 Severity Level Failure Level There are no valid journal groups. All journal groups are used by Universal Replicator for Mainframe or Continuous Access Journal. If possible, delete journal groups of Universal Replicator for Mainframe or Continuous Access Journal, then start the Continuous Access Journal window or the Universal Replicator for Mainframe window.
Part Code 6610 6610 Error Number Error Message Recommended Action 59112 The CLPR number of the specified data volume is different from the CLPR number of the data volume in the Preview list. In this operation, please specify only one CLPR number. 59113 Severity Level Failure Level Please specify only the volume that has the same CLPR number as the CLPR number of the volume in the Preview list.
Part Code Error Number Error Message Recommended Action 59153 The journal volume cannot be deleted because the status of the mirror of the journal group is Active. 6610 6610 Severity Level Failure Level Change the status of the mirror of the journal group to Stop or Initial, then retry the operation. W 0 59321 No more journal groups can be added to the specified extended consistency group (EXCTG). Check the number of journal groups in the specified extended consistency group (EXCTG).
Part Code Error Number Error Message Recommended Action 59330 The local DKC cannot be specified for the extended consistency group (EXCTG), because the serial number other than the local DKC is entered. Delete the entered DKC to use the journal group of the local DKC. Severity Level Failure Level Delete the entered DKC to use the journal group of the local DKC. W 0 59332 A multiplatform volume is included in the specified volumes.
Part Code 6610 6610 Error Number Error Message Recommended Action 69019 69021 Severity Level Failure Level The number of data volumes exceeds the maximum. Reduce the number of data volumes and retry the operation. When the number of volume pairs has already reaches the maximum value, you cannot create volume pairs any further. W 0 Journal groups cannot be added to the extended consistency group (EXCTG), because the number of EXCTG exceeds the maximum. Check the number of registered EXCTG.
Part Code Error Number Error Message Recommended Action 55009 An invalid cache resource number (CLPR No.) was detected. 6805 6805 Severity Level Failure Level Correct the cache resource number (CLPR No.), then retry the operation. If this problem persists, call technical support. E 3 55010 An invalid storage resource number (SLPR No.) was detected. Correct the storage resource number (SLPR No.), then retry the operation. If this problem persists, call technical support.
Part Code 6805 6805 6805 Error Number Error Message Recommended Action Severity Level Failure Level The Level 1 Sleep setting is incorrect. Please correct the setting, then retry. If the same problem persists despite retrying, call technical support. W 5 55219 The Sleep Time setting is incorrect. Please correct the setting, then retry. If the same problem persists despite retrying, call technical support. W 5 55220 The SLPR number is duplicated. Please correct the setting, then retry.
Part Code 6810 6810 6810 6810 6810 Error Number Error Message Recommended Action The options Block Option and Donot Block (Volume Level) cannot be specified at the same time. 55214 Severity Level Failure Level Please correct the setting, then retry. If the same problem persists despite retrying, call technical support. i 0 The Level 2 Threshold setting is incorrect. Please correct the setting, then retry. If the same problem persists despite retrying, call technical support.
Part Code Error Number Error Message Recommended Action 5655 You cannot set a pair because the number of LBA is different for the specified volumes. Severity Level Failure Level Please select other volumes which have the same number of LBA. i 0 5821 This operation has been rejected. The Data Retention Utility setting does not allow the specified volume(s) to be specified as S-VOL(s). Change the Data Retention Utility setting so that the specified volumes can be used as S-VOLs.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level i 0 7005 8504 The command was rejected. The operation failed, because of one of the following reasons: 1. You cannot execute the operation on the specified pair / volume. 2. The pairs of the Normal volume and CV cannot execute QuickRestore. Check the pair or volume status. 7005 8505 The requested command is invalid. Please call technical support. i 0 7005 8506 The command was rejected.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7005 8517 The number of S-VOL cylinders exceeds the maximum. Check the contents, and retry. i 0 8518 You cannot create a pair, because the track format is different for each. Make sure that the specified emulation type is the same for both. Check the emulation type. i 0 7005 8519 You cannot set a pair because the number of cylinders is different for each. Make sure that the capacity is the same for both.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7005 8536 A cache failure was detected. Please call technical support. i 0 7005 8537 The cache capacities do not match. Please call technical support. i 0 7005 8538 An SM failure was detected. Please call technical support. i 0 7005 8539 There is insufficient shared memory to create 4096 pairs. There is insufficient shared memory in DKC. Please call technical support.
Part Code Error Number Error Message Recommended Action 7005 8554 The S-VOL cannot be used. 7005 8555 7005 Severity Level Failure Level Please call technical support, and check if the volume status is normal. i 0 The S-VOL is being formatted. Wait until the volume is formatted, and retry the operation. i 0 8556 This volume cannot be specified as an S-VOL because it is used as a command device. Specify a volume that is not used as a command device as an S-VOL.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7005 8572 The volume is already defined as a P-VOL. Check the status of the volume. i 0 7005 8573 The volume is defined as a source volume for Auto LUN. Release the Auto LUN setting. i 0 7005 8574 The volume is defined as a target volume for Auto LUN. Release the Auto LUN setting. i 0 7005 8575 The selected volume is not a reserved volume. Check the status of the volume.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Check the capacity of the installed license key. To create more pairs, purchase a license key for larger capacity. i 0 7005 8592 The command was rejected, because the licensed capacity was exceeded. 7005 8593 The P-VOL is a source volume for Auto LUN. Release the Auto LUN setting. i 0 7005 8594 The P-VOL is a target volume for Auto LUN. Release the Auto LUN setting.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7005 8610 The S-VOL is a target volume for Auto LUN. Release the Auto LUN setting. i 0 7005 8611 The specified volume is an S-VOL. Check the status of the volume. i 0 7005 8612 The specified volume is not an S-VOL. Check the status of the volume. i 0 7005 8613 The RAID level of the specified S-VOL is not supported. Specify the volume number of the supported RAID level.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7005 8632 The timing of issuing the command is invalid. Please call technical support. i 0 7005 8633 The abnormal status is invalid. Please call technical support. i 0 7005 8634 The volume specified as a reserved volume is already defined as a reserved volume for Auto LUN. Specify other volume(s), or release the Auto LUN Setting.
Part Code Error Message Recommended Action Severity Level Failure Level 8646 The Reverse Copy request was rejected, because the P-VOL was shared with a Continuous Access pair in the non-suspend status. Delete the Continuous Access pair. i 0 7005 8647 The Reverse Copy command has been rejected, because the S-VOL is shared as the S-VOL of a Continuous Access pair. Delete the Continuous Access pair. i 0 7005 8648 The boot device and the P-VOL do not match in the Paircreate command.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7005 8695 The specified MU number is not less than or equal to 2. Correct the MU number, then retry the operation. i 0 7005 8920 Because a L1 pair is not PSUS, you cannot operate to L2. Wait until L1 pair becomes PSUS status, and execute the operation to L2 pair.
Part Code 7005 7005 7005 7005 7005 7005 7005 7005 7005 7005 314 Error Number Error Message Recommended Action 58001 The operation of the L2 pair failed because the L1 pair was in COPY(SP) status, PSUS(SP) status or COPY(RS-R) status. Severity Level Failure Level Wait until the L1 pair status changes to PSUS or PAIR, then retry the operation. i 0 58002 The Quick Restore command has been rejected because the specified pair is composed of a normal volume and a customized volume (CV).
Part Code Error Number Error Message Recommended Action 58301 The reserve volume setting failed because the specified volume was a data volume of Continuous Access Journal. Severity Level Failure Level Release the Continuous Access Journal setting or specify another volume. W 5 58351 The Quick Restore command has been rejected, because the specified pair is composed of internal and external volumes, and also used as a Continuous Access Journal pair.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Release the pool volume or select another volume. W 5 7005 58484 The operation cannot be performed, because the specified reserved volume is a pool volume. 7005 58492 The Pairsplit-S operation has failed. Check the configuration. Refresh the window and check whether the pair exists. W 5 58493 The PCB required for this operation is not mounted. Check the subsystem configuration.
Part Code Error Number Error Message Recommended Action 58579 The operation failed, because the specified volume is being shredded by Data Retention Utility. Retry the operation after the shredding is completed. 7005 Severity Level Failure Level Confirm that the shredding has completed in the Data Retention Utility window, then retry the operation. i 0 58582 The operation failed because the specified S-VOL was used by XP Snapshot. To continue the operation, release the XP Snapshot setting.
Part Code 7005 7005 7005 Error Number Error Message Recommended Action 68737 The command has been rejected, because the specified P-VOL is an XP Thin Provisioning volume not associated with a pool. Severity Level Failure Level Associate the XP Thin Provisioning volume with a pool, then retry the operation. i 5 68738 The command has been rejected, because the specified S-VOL is an XP Thin Provisioning volume not associated with a pool.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Apply the data in the Preview List. To stop the transaction, click [OK] and continue the operation. W 0 7010 5121 The data has been changed. If you select another tab (page), the settings will be discarded. Are you sure you want to continue? 7010 5122 No data has been changed. Go on to the next operation. W 0 7010 5123 The password is invalid. Check the password.
Part Code Error Number Error Message Recommended Action 7010 8658 Some settings could not be applied normally. Refer to the error code. 7010 8659 7010 Severity Level Failure Level Check the error code in Preview list. E 0 The PCB required for this operation is not mounted. Check the subsystem configuration. Mount the required PCB, then retry the operation. i 5 9002 The request operation has completed. The operation was ended normally. Execute the next operation.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level To continue the operation, click [OK]. i 0 7010 59069 The P-VOL and the S-VOL belong to different SLPRs. If you perform this operation, the storage partition administrator will become unable to operate. Do you want to continue this operation? 7010 66102 Information was updated by other users. The list will scroll to the top. Click [OK], then continue the operation.
Part Code Error Number 7105 7105 7105 7105 Error Message Recommended Action 8500 The program product is not installed. 8501 Severity Level Failure Level Check if the necessary key for the program product is installed. i 0 The command was rejected, because a status transition was in progress. Wait a while, and retry the operation. i 0 8502 You cannot reserve the volume, because a Continuous Access pair exists in the same subsystem frame. Delete the Continuous Access pair.
Part Code Error Number Error Message Recommended Action 7105 8511 You cannot reserve the volume, because a path group is set. 7105 8512 7105 Severity Level Failure Level Detach the S-VOL from the host, or delete the Continuous Access path. i 0 Cannot perform Resync or Suspend operation because of the path group setting. Detach the S-VOL from the host, or delete the Continuous Access path. i 0 8513 The command was rejected.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7105 8527 An internal logic error occurred. Please call technical support. i 0 7105 8528 An internal logic error occurred. Please call technical support. i 0 7105 8529 An internal logic error occurred. Please call technical support. i 0 7105 8530 An internal logic error occurred. Please call technical support. i 0 7105 8531 An internal logic error occurred. Please call technical support.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7105 8548 A data transfer failure is detected (DKA). Please call technical support. i 0 7105 8549 The S-VOL is not implemented. You cannot execute the operation for the volume which is not implemented. i 0 7105 8550 The S-VOL cannot be used. Please call technical support, and check if the volume status is normal. i 0 7105 8551 The S-VOL is being formatted.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7105 8566 The attribute of the reserved volume is invalid. Check the contents, and retry. i 0 7105 8567 The number of effective lists is invalid. Please call technical support. i 0 7105 8568 The emulation type is invalid. Specify the volume of the supported emulation type. i 0 7105 8569 The number of differential table or pair table is insufficient.
Part Code Error Number Error Message Recommended Action 7105 8585 The number of reserved volumes exceeds the maximum. 7105 8586 7105 Severity Level Failure Level Stop the operation of the Reserve volume setting, or delete the Reserve volume. i 0 The number of groups that can be set in the same subsystem is invalid. Check the contents, and retry. i 0 8587 The number of pairs that can be set in the same group is invalid. Check the contents, and retry.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level i 0 7105 8602 The volume is already a reserved volume. Specify other volume, and retry the operation. Or release the Reserve attribute of the specified volume, then retry the operation. 7105 8605 The Resync command was issued to a device in the simplex status. Check the pair status. i 0 7105 8606 Cannot create a new pair with this volume, because it is shared as a Continuous Access pair volume.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7105 8625 The P-VOL(S-VOL) and S-VOL(T-VOL) have the same number. Check the specified volume number. i 0 8626 The Simplex command was rejected, because the high-speed Split was in progress. After the high-speed Split is completed, retry the operation. i 0 7105 8627 The Reverse Resync command was rejected, because the high-speed Split was in progress.
Part Code Error Number Error Message Recommended Action 8641 The pairs contain a pair in the Reverse Copy status. 7105 7105 Severity Level Failure Level You cannot execute the specified operation. Release the Reverse Copy for the operation. i 0 8643 The request was rejected, because the Reverse Copy request was made to a pair in the non-Split status. You cannot execute the specified operation. Release the Reverse Copy for the operation.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 7105 8656 An invalid secondary SSID is specified for the Delete Pair or Split Pair command. Check the contents, and retry. i 0 8657 The Swap&Freeze option cannot be specified, because the mode is invalid. Check the setting you specified in Option tab. i 0 8696 The command has been rejected, because the specified S-VOL is being used as the T-VOL of a Compatible FlashCopy V2 pair.
Part Code Error Number Error Message Recommended Action 8992 The command has been rejected, because sufficient amount of shared memory is not installed. 7105 7105 Severity Level Failure Level Please install additional shared memory. W 0 8993 The command has been rejected, because the shared memory is not set for Compatible FlashCopy V2. Please set the shared memory extension setting for Compatible FlashCopy V2. W 0 8994 The command has been rejected, because the storage system is busy.
Part Code 7105 7105 7105 7105 7105 7105 7105 7105 7105 Error Number Error Message Recommended Action 58003 The command has been rejected because a Continuous Access pair exists in the same subsystem frame. Severity Level Failure Level To continue the operation, delete the Continuous Access pair. i 0 58004 The command has been rejected because the issued request is an operation that cannot be performed with a volume that can be used from either the mainframe or open-system hosts.
Part Code Error Number Error Message Recommended Action 58351 The Quick Restore command has been rejected, because the specified pair is composed of internal and external volumes, and also used as a Universal Replicator for Mainframe pair. 7105 Severity Level Failure Level Stop using the specified pair for Universal Replicator for Mainframe, or specify a different pair, then retry the operation.
Part Code 7105 7105 7105 7105 7105 Error Number Error Message Recommended Action 58575 An error occurred while connecting to the subsystem. Please wait for a while, and then retry the operation. Severity Level Failure Level If this problem persists, call technical support. E 6 58585 The operation failed because the CU group of the specified volume is not supported. Volumes that do not belong to CU group 0 are currently not supported. Specify another volume.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level You cannot create a pair for the specified S-VOL. Delete the created pair, and retry the operation. i 0 7110 6504 The number of pairs exceeds the maximum. 7110 7310 Unregistered error code. Please call technical support. W 0 W 0 7110 7311 The settings could not be applied. Wait a while, and retry the operation. If the same error occurs despite retrying, Please call technical support.
Part Code Error Number Error Message Recommended Action 7110 9110 Do you want to execute the Initialize operation? 7110 9377 7110 7110 Severity Level Failure Level To continue processing, click [OK]. Otherwise, click [Cancel]. W 2 Do you want to enable the setting to expand the number of relationships? To continue processing, click [OK]. To stop processing, click [Cancel].
Part Code Error Number Error Message Recommended Action 7110 66102 Information was updated by other users. The list will scroll to the top. 69025 Some pairs are excluded from the pairs to be set, because pairs in invalid status for Split Pair are included in the specified pairs. Severity Level Failure Level Click [OK], then continue the operation. W 0 Change the status of the excluded pair.
Part Code Error Number Error Message Recommended Action 6012 An error occurred during SVP processing. If this problem persists, please call technical support. 8005 Severity Level Failure Level If this problem persists, call technical support. E 3 6023 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 8005 6036 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action 55244 The Cache Residency Manager size set for the CLPR exceeds the maximum available Cache Residency Manager size. CLPR No:%s Severity Level Failure Level Check the settings, then retry the operation. E 6 55245 The number of Cache Residency Manager areas set for the CLPR exceeds the maximum available number of Cache Residency Manager areas. CLPR No:%s Check the settings, then retry the operation.
Part Code 8005 Error Number 56526 Error Message Recommended Action administrator. To continue the operation, please contact the storage administrator. To perform other operations, select a function button. To perform other operations, select a function button. The resources of other SLPR(s) cannot be accessed. Correct the settings, then retry the operation.
Part Code 8105 8105 8105 8105 8105 8105 8105 342 Error Number Error Message Recommended Action 1009 The emulation type of the volumes is not for open systems, or the volumes are not mounted. Check the setting. 1010 1011 1012 1013 1015 1018 Severity Level Failure Level The Configuration information has been already changed. Please check the settings and request the setting of the configuration information again. E 6 An error occurred during SVP processing.
Part Code 8105 8105 8105 8105 8105 8105 8105 8105 Error Number Error Message Recommended Action Severity Level Failure Level An error occurred. If this problem persists, please call technical support. Host mode is invalid. (The specified value is not in the specification.) The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact technical support. E 2 The specified fiber address is wrong.
Part Code 8105 8105 8105 8105 8105 8105 8105 344 Error Number Error Message Recommended Action 1061 Severity Level Failure Level An error occurred. If this problem persists, please call technical support. You are trying to perform LUN Security operation for a port where LUN Security function is invalid. The error does not occur normally because it is guarded in the screen. In the unlikely event that this error occurs, contact technical support.
Part Code 8105 8105 8105 8105 8105 8105 Error Number Error Message Recommended Action 1108 The following volumes cannot be specified when you change command device configurations: • Volumes reserved by Auto LUN • Volumes other than the open-system volumes (including unmounted volumes) 1110 Severity Level Failure Level Command device setting is requested for Reserve volume of Auto LUN. Or it is requested for volumes other than open volumes (including uninstalled volumes).
Part Code Error Number Error Message Recommended Action Severity Level Failure Level E 6 and enable command device security on the volume. 8105 8105 8105 1125 There are no host groups where the WWN will be registered. The Configuration information has been already changed. Please check the settings and request the setting of the configuration information again. 1126 A volume set as a command device cannot be used as a component of a LUSE volume. Select another volume.
Part Code Error Number Error Message Recommended Action Failed to set the host mode because the number of host modes exceeds the maximum that can be set in a port. Severity Level Failure Level The Configuration information has been already changed. Please check the settings and request the setting of the configuration information again. E 6 Failed to set the path because the number of paths exceeds the maximum that can be set in a port. The Configuration information has been already changed.
Part Code Error Number Error Message Recommended Action 8105 1184 The port information is inconsistent with PCB mode information. Severity Level Failure Level Please correct the port information or the PCB mode information. W 0 1190 To define a path to the volume from an iSCSI port, the volume must be read/write-enabled and also usable as an S-VOL (secondary volume). Correct the settings, then retry the operation.
Part Code Error Number Error Message Recommended Action 1352 Logical paths remain on the Fibre-MCU port. This operation may cause a fatal damage to the logical paths. Please stop this operation. If you want to continue this operation, please remove the logical paths from the MCU port first. 1353 Severity Level Failure Level Since the port you are trying to set is for Fibre Continuous Access, you must delete the logical path, then retry the port setting. E 2 S-VOLs remain on the Fibre-RCU port.
Part Code Error Number Error Message Recommended Action 1601 This functionality is not available. Open Volume Management is required. 8105 8105 Severity Level Failure Level Install the necessary program product. When an SLPR is allocated, install a necessary program product for the SLPR. E 6 1904 The specified volume cannot be assigned as a LUSE volume or a command device, and the path of the volume cannot be set because it is being used as a Pool volume. Select another volume.
Part Code Error Number Error Message Recommended Action 8105 2010 The LDEV is used by the HOST, or an error occurred in the server procedure. Severity Level Failure Level Check if I/O from the host to target path/volume does not occur. E 6 2011 The status of the storage system requires maintenance (for example, the subsystem is blocked, the shared memory is inconsistent, or some other problem occurs). Please call technical support.
Part Code Error Number 8105 8105 8105 8105 8105 8105 352 Error Message Recommended Action 2504 No settings can be made because of a volume reserved for RAID Manager. Severity Level Failure Level Release the reserve setting of the volume, then retry the operation. W 5 2510 No path can be set to the specified volume because the addition of volumes is not finished. Please call technical support and finish adding volumes.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Cancel the reserve volume, then retry the operation. E 6 8105 2519 A Business Copy or ShadowImage for Mainframe reserve volume is defined. Cancel the reserve volume, and then retry the operation. 8105 2520 An Auto LUN pair is defined. Cancel the pair definition, and then retry the operation. Cancel the pair definition, then retry the operation. E 6 2521 An Auto LUN pair is defined.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8105 5652 The size of the CSV file is invalid. Please check the CSV file. W 5 8105 5660 The XP Thin Provisioning volume is not associated with a pool. Associate the XP Thin Provisioning and a pool first. Associate the XP Thin Provisioning volume with a pool, then retry the operation. E 6 8105 5700 The file format is invalid. Please enter the text file. E 5 8105 5701 The header is invalid.
Part Code Error Number Error Message Recommended Action 8105 5747 The group cannot be added. Change the name of the group. 8105 5748 8105 Severity Level Failure Level Please correct the name of the group. W 0 The group ID does not exist. Please correct the group ID. W 0 5749 The same group ID is already registered. Please correct the group ID. W 0 8105 5750 The same group name is already registered. Please correct the group name. W 0 8105 5751 The group ID does not exist.
Part Code Error Number Error Message Recommended Action 8105 5771 The CHA cannot be changed to High Speed mode. 8105 5785 8105 Severity Level Failure Level Please correct the port parameters. W 0 The system LU cannot be used. Please correct the CU and LDEV. W 0 5786 The path can be defined only for the A, E, J or N port. Please correct the name of port. W 0 8105 5789 The intermediate volume cannot be specified as a command device. Please correct the CU and LDEV.
Part Code 8105 8105 8105 Error Number 66006 66008 66010 Error Message Recommended Action The number of data items entered in the spreadsheet has exceeded the limit. Severity Level Failure Level Check the spreadsheet, and enter only one serial number under the [SerialNumber] function tag. E 5 The number of digits is invalid. Check the spreadsheet, and set the number of digits of the serial number under the [SerialNumber] function tag to five or less. E 5 The format is invalid.
Part Code Error Number Error Message Recommended Action 8110 5629 The file specified by [File Name on Client] does not exist. 8110 5630 8110 Severity Level Failure Level Correct the specified contents, and retry the operation. E 1 The file specified by [File Name on Client] cannot be read. Correct the specified contents, and retry the operation. E 1 5631 The object specified by [File Name on Client] is not a file. Correct the specified contents, and retry the operation.
Table 69 Error Codes — Part Code 8111 Part Code Error Number Error Message Recommended Action 8111 5627 The file name should be from 1 to 32 characters. 8111 5628 8111 Severity Level Failure Level Correct the specified contents, and retry the operation. E 1 You cannot use following characters for the file name: " \ / : , ; * ? < > | and space. Correct the specified contents, and retry the operation. E 1 5629 The file specified by [File Name on Client] does not exist.
Table 71 Error Codes — Part Code 8305 Part Code Error Number 8305 56524 Error Message Recommended Action This function cannot be used by the storage partition administrator. Select another window. To set this function, contact the storage administrator. Severity Level Failure Level E 3 Table 72 Error Codes — Part Code 8310 Part Code Error Number Error Message Recommended Action Severity Level Failure Level 8310 55040 The specified file does not exist.
Part Code Error Number Error Message Recommended Action 6011 An error occurred during SVP processing. If this problem persists, please call technical support. 8505 Severity Level Failure Level If this problem persists, call technical support. E 2 6012 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 8505 6022 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action An invalid SLPR Name was detected. SLPR No:%s 55013 Severity Level Failure Level Correct the SLPR Name, then retry the operation. If this problem persists, call technical support. E 5 Invalid login information was detected. SLPR No:%s Correct the invalid login information, then retry the operation. If this problem persists, call technical support. E 5 55014 This name is already being used as the CLPR name.
Part Code 8505 8505 8505 8505 8505 8505 8505 8505 8505 Error Number Error Message Recommended Action An attempt has been made to either register newly a SLPR that is already registered, or delete a SLPR that is not registered. Severity Level Failure Level Correct the SLPR settings, then retry the operation. If this problem persists, call technical support. E 5 Some parity groups are already registered in a different CLPR. Specify a different parity group, then retry the operation.
Part Code Error Number Error Message Recommended Action 56501 The login information of the partition management function has been initialized due to detection of conflicting information. Please contact the storage administrator. (To the storage administrator: Please reconfigure the login information.) 8505 8505 Severity Level Failure Level Please contact the storage administrator. (To the storage administrator: Please reconfigure the login information.
Part Code 8505 8505 8505 8505 8505 8505 8505 Error Number Error Message Recommended Action 58312 The configuration cannot be changed because the write pending rate of the intended CLPR is too high. Please wait until the write pending rate falls, and then retry the operation. Severity Level Failure Level Please wait until the write pending rate falls, then retry the operation.
Part Code 8505 Error Number 58339 Error Message Recommended Action TrueCopy Asynchronous for Mainframe pair volumes in a CT group. Specify the parity group so that all the pair volumes in CT group are contained. volumes in CT group are contained. The CLPR which the parity groups belong to cannot be changed because the specified parity groups include only a part of Continuous Access Journal volumes, Universal Replicator for Mainframe volumes or journal volumes in a journal group.
Part Code Error Number Error Message Recommended Action 8510 7440 An error occurred. If this problem persists, please call technical support. 8510 9101 8510 Severity Level Failure Level If the same problem persists despite retrying, call technical support. E 2 Do you want to cancel? To cancel, click [OK]. E 2 9102 Do you want to apply? Click [OK] to execute the operation. E 2 55235 The CLPR name already exists.
Part Code Error Message Recommended Action 57001 The partition configuration may contain some inconsistent information. To initialize partition configuration, select the Yes button. To stop the operation, select the No button. 8510 8510 8510 8510 8510 8510 8510 Error Number Severity Level Failure Level If you clicked [Yes], perform the operation after you set up a SLPR name and other changes. If you clicked [No], restart the operation. If this problem persists, contact the system management.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level If this problem persists, call technical support. E 2 9005 5099 An error occurred during SVP processing. If this problem persists, please call technical support. 9005 5201 This functionality is not available. Parallel Access Volume is required. Install the program product. E 6 6001 An error occurred during SVP processing. If this problem persists, please call technical support.
Part Code Error Number Error Message Recommended Action 7117 An error occurred during SVP processing. If this problem persists, please call technical support. 9005 Severity Level Failure Level If this problem persists, call technical support. E 2 7310 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 9005 8001 An error occurred while connecting to the subsystem.
Table 78 Error Codes — Part Code 9010 Part Code Error Number Error Message Recommended Action 9010 7440 An error occurred during processing. If this problem persists, please call technical support. 9010 9303 There are no valid volumes. Severity Level Failure Level If the same problem persists despite retrying, call technical support. E 2 Check the device emulation type or the definition of the journal volume.
Part Code Error Number Error Message Recommended Action 5820 When the host group has a host to which ports are set, the hosts in this host group cannot be registered in another host group. 9105 9105 Severity Level Failure Level Please check the specified host and port. W 0 6012 An error occurred during SVP processing. If this problem persists, please call technical support. An error occurred during SVP processing. If this problem persists, call technical support.
Part Code Error Number Error Message Recommended Action 9105 67003 The specified host group name has already been used by another LDKC. 9105 67004 The specified LDEV Group name has already been used by another LDKC. Severity Level Failure Level Specify another host group name. W 5 Specify other LDEV group name.
Part Code Error Number Error Message Recommended Action 5616 Some attributes of the security group are invalid. Severity Level Failure Level Please click [OK], check attributes of the security group, and retry the operation. W 0 5617 Attributes of the security group differ from the attributes of other related security groups. Please click [OK], check attributes of the security group, and retry the operation.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level If this problem persists, call technical support. E 2 9110 7440 An error occurred during processing. If this problem persists, please call technical support. 9110 8111 There is no CHA PCB for mainframe computers. Please install PCBs for the mainframe computers, then retry the operation. W 0 9110 8112 There is no valid volume. Please mount volumes, then retry the operation.
Part Code 9110 9110 Error Number Error Message Recommended Action 65662 The data has been changed. The settings will be discarded if you continue the processing. Do you want to switch the LDKC? 69020 If you execute this operation, the setting will be executed forcibly. If you apply security to volumes on which any job is running, the job may end abnormally. Are you sure you want to continue this operation? Severity Level Failure Level To continue processing, click [OK].
Part Code Error Number Error Message Recommended Action Severity Level Failure Level If this problem persists, call technical support. E 3 9205 7111 An error occurred during SVP processing. If this problem persists, please call technical support. 9205 7310 This error code is not registered. If this problem persists, call technical support. E 5 9205 8001 An error occurred while connecting to the subsystem. Please retry a little later. Please retry a little later.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level Check the contents of the Volume Retention Manager spreadsheet. E 5 9205 66001 The function name entered in the spreadsheet is incorrect (The function name is not VR). 9205 66002 The process mode written in the spreadsheet cannot be specified. Check the contents of the Volume Retention Manager spreadsheet.
Table 83 Error Codes — Part Code 9210 Part Code Error Number Error Message Recommended Action Severity Level Failure Level If this problem persists, call technical support. E 2 9210 7060 An error occurred during processing. If this problem persists, please call technical support. 9210 7442 There is an invalid value in the Volume Retention Manager information. If this problem persists, call technical support. E 3 9210 7443 The VTOC information contains one or more invalid values.
Part Code Error Number Error Message Recommended Action 6533 An error occurred during SVP processing. If this problem persists, please call technical support. 9605 Severity Level Failure Level If this problem persists, call technical support. E 3 7060 An error occurred during SVP processing. If this problem persists, please call technical support. If this problem persists, call technical support. E 2 9605 7111 An error occurred during SVP processing.
Part Code Error Number Error Message Recommended Action 8134 You cannot change the attribute of this logical volume to Read/Write. Please call technical support if you want to change the attribute. Severity Level Failure Level You cannot change the attribute of this logical device to Read/Write. Please call technical support To change the attribute. E 5 8135 This logical volume is already used as an S-VOL for Continuous Access or Business Copy.
Part Code Error Number Error Message Recommended Action 8156 You cannot change the access attribute because the expiration lock is set to Enable. 9605 9605 Severity Level Failure Level Please set the expiration lock to Disable, then change the access attribute. E 5 56525 Because the settings across the multiple SLPRs are contained, the authority has been shifted to the storage administrator from the storage partition administrator.
Part Code Error Number Error Message Recommended Action 58419 The access attribute of a primary or a secondary volume for remote copy cannot be changed when VMA is set. 9605 Severity Level Failure Level Suspend the remote copy pair or delete the pair, then retry the operation. E 5 58420 VMA cannot be set for the specified logical volume, because the specified logical volume is a LUSE volume. Release the LUSE volume, or set VMA for a different logical volume.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level E 5 9605 58436 The access attribute of the logical volume has already been changed.
Part Code Error Number Error Message Recommended Action Severity Level Failure Level 58449 The capacity of the logical volume is not the same as that of the external volume with which the logical volume is mapped. Please do one of the following: 1. Execute the Volume Initialize operation on the external group to which the logical volume belongs in the Customized Volume window, and create a volume having the same capacity as the external volume. 2.
Part Code Error Number 9610 9610 Error Message Recommended Action 58405 There is an invalid value in the Extent information. 59106 If you set VMA, all the data or part of the data written in the logical volume will be deleted. Do you want to continue the operation? Severity Level Failure Level If this problem persists, call technical support. E 3 To set VMA, click [OK]. Otherwise, click [Cancel].
A Acronyms and Abbreviations Table 87 Acronyms and Abbreviations API application program interface CCI RAID Manager CHA channel adapter CT consistency CTG consistency group CU control unit CV customized volume DASD direct-access storage device DFW DASD fast write DKA disk adapter DKC disk controller IP internet protocol L1, L2 level 1, level 2 LAN local-area network LBA logical block address LCP local control port LDEV logical device LU logical unit LUN logical unit numb
R-VOL remote volume SIM service information message SM shared memory SMPL simplex SNMP simple network management protocol SSID subsystem ID S-VOL secondary volume (Continuous Access), source volume (ShadowImage for Mainframe) SVP service processor T-VOL target volume storage system HP storage system VDEV virtual device WWN worldwide name 388 Acronyms and Abbreviations
