HP StorageWorks XP24000/XP20000 Audit Log User and Reference Guide Part number: AE131-96013 Second edition: September 2007
Legal and notice information © Copyright 2007 Hewlett-Packard Development Company, L.P. Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor's standard commercial license. The information contained herein is subject to change without notice.
Contents About this Guide ................................................................................ 19 Intended Audience .................................................................................................................... Related Documentation .............................................................................................................. Document Conventions ..............................................................................................................
Logout Operation ..................................................................................................................... 57 Set System Info Operation .......................................................................................................... 57 8 Cache Function ................................................................................ 59 Cache Residency Manager (DCR) Prestaging Operation ................................................................
Format Stop Operation .............................................................................................................. 88 Initialize ORM Value Operation .................................................................................................. 88 Install Operation ....................................................................................................................... 89 Install CV Operation .................................................................................
Set Set Set Set Set Set Set Set Set Set Set Set Fibre-Channel Security Protocol (FCSP) Host Operation ........................................................... Fibre-Channel Security Protocol (FCSP) Port Info Operation ...................................................... Fibre-Channel Security Protocol (FCSP) Port Switch Operation .................................................. Fibre-Channel Security Protocol (FCSP) Target Operation ........................................................
23 Remote Control Unit (RCU) Function ................................................ 175 Add Path Operation ................................................................................................................ Add RCU Operation ............................................................................................................... Change RCU Option Operation ............................................................................................... Delete Path Operation .............
Change Consistency Group (CTG) Option Operation .................................................................. Change Option Operation ....................................................................................................... Change Pair Option Operation ................................................................................................ Clear SIM Operation ..............................................................................................................
Volume to Space Operation ..................................................................................................... 257 34 HP XP Auto LUN Software Function ................................................. 259 Del Auto Plan Log Operation ................................................................................................... Del Migration Log Operation .................................................................................................... Set Migration Vol Operation ....
Figures 1..Syslog Main Window ............................................................................................. 26 2..Audit Log Information File ........................................................................................ 29 3..Syslog Information File ............................................................................................ 32 4..Items Described in Sample Audit Logs ....................................................................... 45 5..
Tables 1..Document conventions ............................................................................................. 19 2..Audit Log File Components ...................................................................................... 26 3..Audit Log File Output .............................................................................................. 27 4..Items in Audit Log Information File ............................................................................. 29 5..
33..Detailed Info: Add Host Group Operation ................................................................. 77 34..Detailed Info: Add LU Path Operation ....................................................................... 78 35..Detailed Info: Add WWN Operation ........................................................................ 79 36..Detailed Info: All Config Operation ........................................................................... 79 37..Detailed Info: Assist Config Operation ........
69..Detailed Info: Set Battery Life Operation .................................................................. 106 70..Detailed Info: Set Channel Speed Operation ............................................................ 106 71..Detailed Info: Set Command Device (CommandDev) Operation .................................. 107 72..Detailed Info: Set Command Device Security (CommandDevSec) Operation ................. 108 73..Detailed Info: Set Fibre Address Operation .........................................
105..Detailed Info: Delete LU Path Operation ................................................................... 135 106..Detailed Info: Delete WWN Operation ................................................................... 136 107..Detailed Info: Set Authentication Operation ............................................................. 136 108..Detailed Info: Set Channel Speed Operation ............................................................ 137 109..
142..Parameters: Monitoring Switch (SW) Operation ........................................................ 167 143..Parameters: Monitoring Switch (SW) Operation ........................................................ 168 144..Detailed Info: Change Port Operation ..................................................................... 169 145..Detailed Info: PP Disable chk Operation .................................................................. 171 146..Detailed Info: PP Enable chk Operation ..............
179..Detailed Info: Paircreate Operation ......................................................................... 204 180..Detailed Info: Pairresync Operation ......................................................................... 205 181..Detailed Info: Pairsplit-r Operation .......................................................................... 207 182..Detailed Info: Pairsplit-S Operation ......................................................................... 208 183..
216..Detailed Info: Suspend-Pair Operation ..................................................................... 242 217..Detailed Info: System-Option Operation ................................................................... 244 218..Parameters: Change-CacheMode Operation ............................................................ 246 219..Detailed Info: Change-CacheMode Operation ......................................................... 246 220..Detailed Info: ChkPath-RestoreVol Operation ............
About this Guide This document describes and provides instructions for using the audit log feature on the HP StorageWorks XP24000/XP20000 Disk Array. The term storage system in this guide refers to an HP StorageWorks XP24000/XP20000 Disk Array. Intended Audience This document assumes that: • The user is familiar with the operating system and web browser software on the system hosting the HP XP Remote Web Console software.
Convention Element Italic text Text emphasis Monospace text • File and directory names • System output • Code • Commands, their arguments, and argument values Monospace, italic text • Code variables • Command variables Monospace, bold text Emphasized monospace text NOTE: Provides additional information.
Before contacting HP, collect the following information: • • • • • • Product model names and numbers Technical support registration number (if applicable) Product serial numbers Error messages Operating system type and revision level Detailed questions Subscription Service HP recommends that you register your product at the Subscriber's Choice for Business website: http://www.hp.
About this Guide
1 Introduction This chapter introduces the audit logs created by the HP XP Remote Web Console or SVP (Service Processor) on the storage system. The SVP is a computer that is contained within the storage system. Users can access the audit logs that are output by the SVP, but the SVP itself is accessible only by HP personnel.
NOTE: Audit Log Administrator Role needs to be set to Modify or View for the user account of that storage administrator. 2. Click the ( , , or ) button in the HP XP Remote Web Console main window. The window to specify the download destination appears: • • ) appears when the number of saved lines in the audit log information Audit:Normal button ( file is below the threshold.
• If using a primary syslog server: • Select Enable in Output to Primary Server. • Enter the IP Address in Primary Server Setting. You do not have to enter the periods. • Enter the Port Number in Primary Server Setting. You can enter a number from 1 to 65,535. • If using a secondary syslog server: • Select Enable in Output toSecondary Server. • Enter the IP Address in Secondary Server Setting. You do not have to enter the periods. • Enter the Port Number in Secondary Server Setting.
Figure 1 Syslog Main Window Audit Log File Description The following table describes the audit log file components: Table 2 Audit Log File Components Component Audit Log Information File Syslog Information File File Name audit.log syslog.log Downloaded File Name auditYYYYMMDD.tgz syslogYYYYMMDD.
Component Audit Log Information File Syslog Information File Maximum File Size 122.5 MB 244.6 MB Threshold Once the audit log reaches its maximum capacity, the starting line of the oldest data begins to be overwritten with the starting line of the newest data (wrap around). When you reach 70% of this threshold, the yellow Audit:Warning button appears on the HP XP Remote Web Console Main window.
Introduction
2 Audit Log File Format This chapter describes the two types of audit log files and the items included in the files. • Audit Log Information File, page 29 • Syslog Information File, page 31 Audit Log Information File The audit log information file consists of both basic and detailed information about user logins, logouts and disk array configuration change operations. The detailed information includes an index representing each item and its setting's values.
No. Item Explanation 3 Date Year, month and day the audit log was created (YYYYMMDD). 4 Time Hour, minute, second and millisecond the audit log was created (HH:MM:SSxxx). 5 Time zone The time difference between Universal Time (UT) and the local time appears as ±HH:MM (HH: hour, MM: minute). 6 Function name The abbreviation indicating the function or option which has been used to perform the setting operation is output. 7 Operation or event name The operation or option name.
Symbol Definition + means the beginning of the index. The number of occurrences of + represents the number of indents. - means that the line continues from the previous line. = Connects an index and a setting value. [] When there is more than one setting value for one index, the setting values are enclosed by [ ], and separated by a comma (,). Example: CU:LDEV=[0x00:0x00,0x00:0x01,0x00:0x02] {} Details are enclosed by {}.
Figure 3 Syslog Information File Table 6 Items in the Syslog File No. Item Description 1 Priority The priority according to the following formula, enclosed by brackets (< >): Priority = 8 × Facility + Severity Facility is 1 (fixed). The Severity depends on the type of log information: 3: Error. The operation has ended abnormally. 4: Warning. The operation has partly ended abnormally or was canceled during the operation. 6: Informational. The operation has ended normally.
No. Item Description 5 Unified specification identification information The Unified specification identification character (CELFSS). 6 7 8 Message identification information 9 Date, time#2 The revision number of the Unified specification document (1.1). The serial number of the syslog header information. Message ID. Not displayed because it is not used. The date, time and the time difference between UTC (Coordinated Universal Time) in the format of YYYY-MM-DD-Thh:mm:ss.
No. Item Description 16 Generated location information Not displayed because it is not used. 17 Related information The location identification name set by the user in the Syslog window. 18 FQDN. Not displayed because it is not used. 19 Redundant identification information. Not displayed because it is not used. 20 Agent information Not displayed because it is not used. 21 Detailed information Host sending the request. Not displayed because it is not used. 22 Port sending the request.
No. Item Description • The event name is displayed instead of the operation when the function is [AuditLog]. See Table 3 and Table 7. 30 The same information contained in the basic information of the audit log information file is also displayed. For more information, see Figure 2.
Audit Log File Format
3 Understanding the Audit Log Information File The following table shows the audit log functions, operations, and program products.
Function Name Install 38 Operation Name Page SIM Reporting Option 74 Threshold Value 74 Add Host Group 77 Add LU Path 78 Add WWN 78 All Config 79 Assist Config 80 Backup Config 80 Change Host Group 81 Change WWN 81 DCR Prestaging 82 Define Config.
Function Name LDEV LUNM Operation Name Page Set Fibre Topology 108 Set Host Mode 109 Set IP Address 110 Set Security Switch 111 Set Speed Mode 112 Set Subsystem Time 112 System Option 114 System Tuning 116 Uninstall 117 Update Config 122 Volume to Space 123 Volume-Blockade 125 Volume-Format 125 Volume-Format(H) 126 Volume-Restore(N) 127 Add Host Group 129 Add LU Path 129 Add WWN 130 Auth Info (Host) 131 Auth Info (Target) 132 Change Host Group 132 Change WWN 1
Function Name Operation Name Page Set Security Switch 147 Set Speed Mode 148 Set TCP/IP Port 148 Make LUSE 151 Release LUSE 151 Blockade 153 Correction Copy 154 Drive Interrupt 154 Format 155 Format Stop 156 Recover 157 Replace 157 Restore 159 Restore Data 160 Size Change 160 Spare Disk 161 Switch SVP 162 Transfer Config 162 Type Change 162 Verify 163 Verify Stop 164 OND Release Cache/CLPR 165 On-Demand Perf Mon Monitoring S/W 167 Performance Monitor Moni
Function Name Operation Name Page Option Name RCU Add Path 175 Add RCU 176 Change RCU Option 177 Delete Path 178 Delete RCU 179 RCU operation (HP XP Continuous Access Software, TrueCopy for Mainframe, HP XP Continuous Access Journal Software, or Universal Replicator for Mainframe) Change Reserve 181 Initialize 181 Option 182 Paircreate 182 Pairresync 183 Pairsplit 184 Pairsplit-E 185 Pairsplit-S 186 Add Pair 187 Change Reserve 188 CTG 188 Delete Pair 189 Initialize 1
Function Name Cnt Ac-J UR Ext Stor 42 Operation Name Page Change Option 215 Change Pair Option 216 Clear SIM 217 Delete CTG 217 Delete Pair 218 Resume Pair 219 Script Operation 220 Start Pair 220 Suspend Pair 221 Journal-Option 223 Journal-Vol 224 Journal-Vol 225 Paircreate 226 Pairresync 227 Pairsplit-r 228 Pairsplit-S 229 Pair-Option 230 System-Option 231 Add-Pair 233 Clear-SIM 234 Delete-Pair 234 Edit-EXCTG 235 Journal-Option 237 Journal-Vol 238 Jour
Function Name Operation Name Page Option Name VLL Install CV 253 Make Volume 254 Virtual LVI / Virtual LUN (VLL) Set SSID 255 Volume Initialize 256 Volume to Space 257 Del Auto Plan Log 259 Del Migration Log 259 Set Migration Vol 259 Set Reserved Vol 260 DCPart Set 263 HP XP Disk/Cache Partition VRM Attribute 265 Volume Retention Manager VTOC 266 End Shredding 267 Set Shredding 267 Suspend Shredding 268 VSEC Set Group 271 Volume Security VVOL Add V-Vol (V) 275
Understanding the Audit Log Information File
4 Sample Audit Logs The following chapters provide a sample audit log for each function and operation that can be performed with the HP XP Remote Web Console. The individual items in each sample log are described, starting with function name. This includes function name, operation name, parameter, operation result, and sequence number, as shown in Figure 4.
Sample Audit Logs
5 Audit Log Function Create File ,,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[AuditLog],Create File,AuditLog,Warning,,,Seq.=xxxxx [Audit Log] Audit Log function Create File Create File event AuditLog This parameter indicates the audit log information file has been reproduced. Warning The operation has partly ended abnormally or was canceled during the operation. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Over MaxLine Event 14> Jan 4 06:25:18 SVP Storage: CELFSS,1.
This information is displayed in the syslog information file only. No parameters display for this event. [Audit Log] Audit Log function Over Threshold Over Threshold event Normal end The operation has ended normally. Set Syslog Server Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Audit Log],Set Syslog Server,DetailFlg=Enable,Normal end,,,Seq.=xxxxx +DetailFlg=Enable +LocationInfo=USP001 +{ServerType,IPAddrVer,OutFlg,SrvAddr,SrvPortNum}=[{Primary,IPv4,Disable, 192.168.0.
Item Description LocationInfo The location identification information for the storage system. Not output when setting is not changed. ServerType The syslog server to which information is output. Not output when setting is not changed. Primary: Primary syslog server. Secondary: Secondary syslog server. IPAddrVer The version number of the internet protocol. If the setting is not changed, a hyphen (-) is displayed. IPv6: Internet Protocol Version 6 (not supported).
Audit Log Function
6 Account Function Set User Account Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[Account],Set User Account,,Normal end,,,Seq=xxxxx +Operation=Change +{UserID,Authority,SLPRNo,WritePermission,ReadPermission,AccountFlag}= -[{use001,Administrator,65535,FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF FFFFFFFFFF FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF,-,Enable}, -{use002,User,1,-,-,Disable}]Num.
Item Description ReadPermission The read permission for each function appears as a hexadecimal character string. If a hexadecimal number is indicated for the binary number, a bit position will describe the relationship between each function and its read permissions. (see Table 12). A dash (-) appears when nothing is changed. AccountFlag Indicates whether the user account is enabled or disabled. Disable or Enable will appear. Num of Users The number of users.
Bit Position in Binary (descending order) Function Name Permission of Storage Partition Administrator (*2) Remarks 105 Universal Volume Manager - *1, *3 104-98 Not used - 97 Data Retention Utility Yes 96-77 Not used - 76 Not used - 75 Volume Retention Manager - *1, *3 74 Volume Security - *1, *3 73 Compatible PAV - *1, *3 72-66 Not used - 65 ShadowImage for z/OS - 64-58 Not used - 57 TrueCopy for z/OS - 56-50 Not used - 49 Business Copy - 48-42 Not used -
Bit Position in Binary (descending order) Function Name Permission of Storage Partition Administrator (*2) Remarks 11 Authentication Yes *1, *3 10 Port Yes *1, *3 9 LUN Manager Yes *1, *3 8 Permission of Audit Log - *3 7 Permission of Account Yes *3 6-4 Not used - 3 Status - *4 2 Port Status - *4 1 Information Yes (for read permission only) *1, *3 *1: Write permission or read permission will be valid only when the read permission of storage administrator (145th bit) is
Detailed information displays for this operation, as shown in the following table. Table 13 Detailed Info: Set Login Message Operation Item Description LoginMessageSentence Indicates the sentence of login Message displayed on the login window of HP XP Remote Web Console.
Account Function
7 BASE Function Login Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[BASE],Login,IP=66.93.43.19,Normal end,,,Seq.=xxxxx [BASE] BASE function Login Login operation IP= Logged in, HP XP Remote Web Console computer IP address Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Logout Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[BASE],Logout,,Normal end,,,Seq.
[BASE] BASE function Set System Info Set System Information operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 14 Detailed Info: Set System Info Operation Item Description Name Nickname of the device Contact Name of the system administrator. Location Installation location of the device.
8 Cache Function Cache Residency Manager (DCR) Prestaging Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Cache],DCR Prestaging,, Normal end,,,Seq.=xxxxx [Cache] Cache function DCR Prestaging DCR Prestaging operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Delete Cache Residency Manager for z/OS (M/F DCR) Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[Cache],Delete M/F DCR,,Normal end,,,Seq.
Detailed information displays for this operation, as shown in the following table. Table 15 Detailed Info: Delete Cache Residency Manager for z/OS (M/F DCR) Operation Item Description LDKC:CU:LDEV The LDKC, CU and LDEV number of the logical volume (for a mainframe system) where the setting information for Cache Residency cache is canceled. Start CC-HH The starting cylinder number (CC) and the starting head number (HH) of the cancelled data.
Set Cache Residency Manager for z/OS (M/F DCR) Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Cache],Set M/F DCR,,Normal end,,,Seq.=xxxxx +{LDKC:CU:LDEV,Mode,Prestaging,Start CC-HH,End CC-HH}=[{0x00:0x00:0x00,Bind,No, XXXXXX-XX,XXXXXX-XX},{0x00:0x00:0x00,Priority,Yes,XXXXXX-XX,XXXXXX-XX}],Num. of LDEVs=2 [Cache] Cache function Set M/F DCR Set M/F DCR operation Normal end The operation has ended normally. Seq.
Set Open DCR Set Open DCR operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table.
9 Configuration File Loader (CFL) Function LUN Manager (LUNM) Operation NOTE: The Configuration File Loader log appears in the log file line. It is located between where the line contains “Start” and the line contains “End.” user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[CFL],LUNM Operation,Start,Normal end,,,Seq.=xxxxx [CFL] Configuration File Loader function LUNM Operation LUN Manager operation Start Start is the selected parameter.
user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[CFL],VRM Operation,Start,Normal end,,,Seq.=xxxxx [CFL] Configuration File Loader function VRM Operation Volume Retention Manager operation Start Start is the selected parameter. This operation uses the following parameters, as shown in the following table. Table 20 Parameters: Configuration File Loader - VRM Operation Parameter Description Start Start of the Configuration File Loader. End End of the Configuration File Loader.
10 HP XP for Compatible Parallel Access Volumes (CPAV) Software Function Add Alias Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[CPAV],Add Alias,,Normal end,,,Seq.=xxxxx +LDKC=0x00,CU=0x00 ++{Alias LDEV,Base LDEV}=[{0xFD,0x00},{0xFE,0x00},{0xFF,0x01}],Num. of Alias LDEVs=3 +LDKC=0x00,CU=0x01 ++{Alias LDEV,Base LDEV}=[{0xFF,0x00}],Num. of Alias LDEVs=1 +Num. of Alias LDEVs=4 [CPAV] CPAV function Add Alias Add Alias operation Normal end The operation has ended normally. Seq.
Delete Alias Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[CPAV],Delete Alias,,Normal end,,,Seq.=xxxxx +LDKC=0x00,CU=0x00 ++{Alias LDEV,Base LDEV}=[{0xFD,0x00},{0xFE,0x00},{0xFF,0x01}],Num. of Alias LDEVs=3 +LDKC=0x00,CU=0x01 ++{Alias LDEV,Base LDEV}=[{0xFF,0x00}],Num. of Alias LDEVs=1 +Num. of Alias LDEVs=4 [CPAV] HP XP for Compatible Parallel Access Volumes Software function Delete Alias Delete Alias operation Normal end The operation has ended normally. Seq.
11 Data Retention Utility Function Attribute Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Data Ret],Attribute,,Normal end,,,Seq.=xxxxx +{LDKC:CU:LDEV,Attribute,RT,Result}=[{0x00:0x00:0x01,0x80,100,Normal end}, {0x00:0x00:0x02,0x82,Unlimited,Error(9605-8122)},{0x00:0x00:0x03,0x81,200, Normal end}, {0x00:0x00:0x03,0x81,xxxx,Normal end}],Num. of LDEVs=XXX [Data Ret] Data Retention Utility function Attribute Attribute operation Normal end The operation has ended normally. Seq.
Item Description NOTE: A hyphen (-) is output when setting is not changed. RT The number of days set in Retention Term. NOTE: A hyphen (-) is output when setting is not changed. Result The result of operation. Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of LDEVs The number of the logical volume(s) where the attribute has been set. * When bit 5, 6, and 7 are all 0 (zero), Read/Write has been set.
12 FlashCopy (FC) Function Set SCP Time Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[FC],Set SCP Time,,Normal end,,,Seq.=xxxxx +{LDKC,CU,SCP Time(s)}= -[{0x00,0x00,600},{0x00,0x01,600},{0x00,0x02,600},{0x00,0x03,600},{0x00,0x04,600}, (snip), {0x00,0xFE,600}],Num. of CUs=255 [FC] FlashCopy function Set SCP Time Set State Change Pending (SCP) Time operation Normal end The operation has ended normally. Seq.
FlashCopy (FC) Function
13 Information Function Delete Log Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xx, 00:00,[Information],Delete Log,SIM,Normal end,,,Seq.=xxxxx [Information] Information Function Delete Log Delete Log operation SIM SIM is the selected parameter. This operation uses the following parameters, as shown in the following table. Table 26 Parameters: Delete Log Operation Parameter Description SIM The deletion of SIM log. SSB The deletion of SSB log. Reset The deletion of Reset log.
ORM Value Operation Example 1 (changing the threshold) user-name,xx,YYYY/MM/DD,HH:MM:SS:xx, 00:00,[Information],ORM Value,Alter,Normal end,,,Seq.=xxxxx +Type=7days +{Read Err.(Unrecovered),Read Err.(Recovered),Seek Err.(Recovered),Seek Err. (Unrecovered), Not Ready,Other Errors}={15,1.00e-008,100,10,10,10} ++PDEV=[HDDR00-01,HDDR00-02,(snip)],Num. of PDEVs=1152 Example 2 (Error Reset) user-name,xx,YYYY/MM/DD,HH:MM:SS:xx, 00:00,[Information],ORM Value,Error Reset,Normal end,,,Seq.
Item Description Read Err.(Recovered) The threshold of Read Error (Recovered). Seek Err.(Recovered) The threshold of Seek Error (Recovered). Seek Err.(Unrecovered) The threshold of Seek Error (Unrecovered). Not Ready The threshold of Not Ready. Other Errors The threshold of Other Errors. PDEV The mounting location of the PDEV (physical device) which is the target of Alter or error reset. Num. of PDEVs The number of PDEVs (physical devices).
SIM Reporting Option Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xx, 00:00,[Information],SIM Reporting Option,,Normal end,,,Seq.=xxxxx +Type=DKC SIM ++{Acute,Serious,Moderate,Service}={ON,ON,ON,ON} +Type=Cache SIM ++{Acute,Serious,Moderate,Service}={ON,ON,ON,ON} +Type=Media SIM ++{Acute,Serious,Moderate,Service}={ON,ON,ON,ON} +Type=Device SIM ++{Acute,Serious,Moderate,Service}={ON,ON,ON,ON} +Num.
user-name,xx,YYYY/MM/DD,HH:MM:SS:xx, 00:00,[Information],Threshold Value,Alter,Normal end,,,Seq.=xxxxx +Type=7days +{Mechanical error(Recovered,Unrecd.),Media error(Recovered,Unrecd.), Read/Write error(Recovered,Unrecd.),Drive I/F error(Recovered,Unrecd.), Controller hardware error(Recovered,Unrecd.),FC I/F error Port 0(Unrecd.), FC I/F error Port 1(Unrecd.),Prot 0 error(Unrecd.),Port 1 error(Unrecd.)} ={(150,60),(0,15),(150,30),(150,6),(150,6),6,6,12,12} ++PDEV=[HDDR00-01,HDDR00-02,(snip)],Num.
Item Description Read/Write error (Recovered,Unrecd.) The threshold of Read/Write error. Drive I/F error (Recovered,Unrecd.) The threshold of Drive I/F error. Controller hardware error (Recovered,Unrecd.) The threshold of Controller hardware error. FC I/F error Port 0 (Unrecd.) The threshold of FC I/F error Port 0. FC I/F error Port 1 (Unrecd.) The threshold of FC I/F error Port 1. Prot 0 error (Unrecd.) The threshold of Prot 0 error. Prot 1 error (Unrecd.) The threshold of Prot 1 error.
14 Install Function Add Host Group Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Add Host Group,,Normal end,,,Seq.=xxxxx +{Port,HostGrpID,HostGrpName,Mode,Option[0:31],Option[32:63],Option[64:95]}={XX, 0xXXX,XXXXXXXXXXXXXXXX,0xXX,0xXXXXXXXX,0xXXXXXXXX,0xXXXXXXXX} ++{WWN,Nickname}=[{0xXXXXXXXXXXXXXXXX,XXXXXXXXXXXXXXXX},{0xXXXXXXXXXXXXXXXX, XXXXXXXXXXXXXXXX}],Num.
Item Description Num. of WWNs The number of WWNs of the host registered in the host group. Num. of Host Groups The number of added host groups. Add LU Path Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Add LU Path,,Normal end,,,Seq.=xxxxx +{Port,HostGrpID,LUN,LDKC:CU:LDEV}=[{XX,0xXXX,0xXXX, 0xXX:0xXX:0xXX},{XX,0xXXX,0xXXX, 0xXX:0xXX:0xXX},{XX,0xXXX,0xXXX,0xXX:0xXX:0xXX}],Num.
Add WWN operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 35 Detailed Info: Add WWN Operation Item Description Port The name of the port where the host group is created. HostGrpID The host group number where the host is registered. WWN Indicates WWN of the host bus adapter for the host registered in the host group.
Assist Config Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,GMT,[Install],Assist Config,,Normal end,,,Seq.=xxxxx +{New Ver.,Old Ver.}={xx-xx-xx/xx,xx-xx-xx/xx} [Install] Install function Assist Config Assist Config operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table.
Detailed information displays for this operation, as shown in the following table. Table 38 Detailed Info: Backup Config Operation Item Description Ver. The version number of the configuration information to be backed up. Change Host Group Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Change Host Group,,Normal end,,,Seq.=xxxxx +{Port,HostGrpID,HostGrpName}=[{XX,XXX,XXXXXXXXXXXXXXXX},{XX,XXX,XXXXXXXXXXXXXXXX}], Num.
Change WWN operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 40 Detailed Info: Change WWN Operation Item Description Port The name of the port where the host is connected. HostGrpID The host group number on which the host with WWN or nickname of the host bus adapter being changed is registered.
Define Config. Define Config. operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Delete Disk Controller (DKC) WWN Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Delete DKC WWN,,Normal end,,,Seq.=xxxxx +{Port,Delete WWN}=[{XX,0xXXXXXXXXXXXXXXXX},{XX,0xXXXXXXXXXXXXXXXX}], Num. of WWNs=2 [Install] Install function Delete DKC WWN Delete DKC WWN operation Normal end The operation has ended normally. Seq.
Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 42 Detailed Info: Delete Host Group Operation Item Description Port The name of the port where the host group deleted or initialized was created. HostGrpID The host group number deleted or initialized. Num. of Host Groups The number of host groups deleted or initialized.
Item Description Num. of Paths The number of LU paths deleted. Delete WWN Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Delete WWN,,Normal end,,,Seq.=xxxxx +{Port,HostGrpID,WWN}=[{XX,0xXXX,0xXXXXXXXXXXXXXXXX},{XX,0xXXX,0xXXXXXXXXXXXXXXXX}], Num. of WWNs=2 [Install] Install function Delete WWN Delete WWN operation Normal end The operation has ended normally. Seq.
Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 45 Detailed Info: Disk Unit (DKU) Emulation Operation Item Description Type The emulation type. LDEV(LDKC:CU:LDEV) The LDKC, CU and LDEV numbers where the emulation type is changed. Num. of LDEVs The number of logical volumes where the emulation type is changed.
Format Operation NOTE: This log information indicates the completion of Format operation and does not indicate the completion of Format process. user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Format,,Normal end,,,Seq.=xxxxx +PG=[1-1],Num. of PGs=1 +PG=[E1-1],Num. of PGs=1 (for an external volume) +PG=[V1-1],Num. of PGs=1 (for a virtual volume) +PG=[X1-1],Num. of PGs=1 (for a Dynamic Provisioning volume) +LDEV=[0x00:0x03:0x2f],Num.
Format Stop Operation NOTE: This log information is output when the format process is suspended. user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Format Stop,,Normal end,,,Seq.=xxxxx +PG=[1-1],Num. of PGs=1 +PG=[E1-1],Num. of PGs=1 (for an external volume) +PG=[V1-1],Num. of PGs=1 (for a virtual volume) +PG=[X1-1],Num. of PGs=1 (for a Dynamic Provisioning volume) +LDEV=[0x00:0x03:0x2f],Num.
The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Install Operation Example 1 (installing additional channel adapters) user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Install,,Normal end,,,Seq.
Item Description Fibre PCB Mode The speed mode of the Fibre PCB is indicated for open systems. : Standard mode. : High speed mode/Mix mode. Initiator/Target The type of Initiator or Target. Channel Speed The channel speed is indicated for open systems. 1: 1 Gbps, 2: 2 Gbps, 4: 4 Gbps, Auto: Auto mode. CU Number Indicates the range of the CU number which the port belongs. Num of Ports The number of ports. HTP The HTP is indicated for FICON.
Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 50 Detailed Info: Install Operation (Installing Additional Subsystems, ECC Groups or LDEVs) Item Description Disk Adapter (DKA) The Disk Adapter (DKA) mounting location. Transfer Rate The transfer rate of Disk Adapters (DKA). Num. of Disk Adapters (DKA) The number of Disk Adapters (DKA).
Item Description Num. of SPAREs The number of spare drives. NOTE: Only the changed items will be output. The Detailed information for the recovery process will not be output when the installation process is executed before the process has completed. However, the setting of the recovery process will be output as the Detailed information for the process when the installation process is executed before the recovery process has not completed.
Item Description CLPR The CLPR number. Cache size The capacity of the cache memory allocated to CLPR. DCR size The capacity of Cache Residency allocated to CLPR. Extent Number The number of extents allocated to CLPR. Num. of CLPRs The number of CLPR. SM The mounting location of the shared memory. Slot The slot position of the shared memory module. Size The capacity of the shared memory. Num. of SMMs The number of shared memory modules. Battery The mounting location of the battery.
Detailed information displays for this operation, as shown in the following table. Table 52 Detailed Info: Install Operation (Installing Additional Shared Memory) Item Description SM The mounting location of the PCB for shared memory. Slot The slot position of the shared memory module. Size The capacity of the cache memory module. Num of SMMs The number of shared memory modules. PP Flag The option flags. Num of PP Flags The number of option flags. Max Number of CUs The maximum number of CUs.
Detailed information displays for this operation, as shown in the following table. Table 53 Detailed Info: Install Operation (Installing Additional Power Supply) Item Description Redundant Power Supply The installed additional cluster power supply. Num. of Redundant Power Supplies The number of additional cluster power supplies. Example 6 (installing additional battery) user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Install,,Normal end,,,Seq.
Install CV Install CV operation No parameter or Non Format No parameter is selected. This operation uses the following parameters, as shown in the following table. Table 55 Parameters: Install CV Operation Parameter Description No parameter Formatted Install CV. Non Format Unformatted Install CV. Normal end The operation has ended normally. Seq.
Install function Machine Install Date Machine Install Date operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 57 Detailed Info: Machine Install Date Operation Item Description Date Indicates the date and the time of the setting in YYYY/MM/DD HH: mm format (YYYY: year, MM: month, DD: day, HH: hour, mm: minute).
Make Vol./Vol. Init Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Make Vol./Vol. Init,,Normal end,,,Seq.=xxxxx +{PG,LDKC:CU:LDEV,Slot,Emulation,Size,Unit,System Disk,SSID}=[{1-1-(1), 0x00:0x14:0x00, -,OPEN-V,205440,LBA,Disable,0x0005}],Num. of LDEVs=1 [Install] Install function Make Vol./Vol. Init Make Vol./Vol. Init operation No parameter or Non Format No parameter is selected. This operation uses the following parameters, as shown in the following table. Table 59 Parameters: Make Vol.
Item Description Num. of LDEVs The number of LDEVs. Micro Program Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,GMT,[Install],Micro Program,,Normal end,,,Seq.=xxxxx +Micro Media=Floppy Disk +Exchange How=Online +Open Port Mode=Stop SCSI +Reboot Grp.=By 1/2 +{Micro Kind, Old Ver, New Ver}=[{DKCMAIN, 5007000000, 5007000001}, {SVP, 50070000, 50070001},(snip)],Num.of Kind=10 [Install] Install function Micro Program Micro Program operation Normal end The operation has ended normally. Seq.
MP Install Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,GMT,[Install],MP Install,,Normal end,,,Seq.=xxxxx +Micro Program={Minimum Config,DKCMAIN,RAMBOOT,LCP,HTP,LCDG,FCDG}, Num. of Kind=7 +Target MP={CHP00-1E,CHP01-1E,DKP80-1A},Num. of MP=3 [Install] Install function MP Install MP Install operation Normal end The operation has ended normally. Seq.
Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 63 Detailed Info: Cache Residency Manager for z/OS (M/F DCR) Operation Item Description LDKC:CU:LDEV The LDKC number, the CU number and the LDEV number of the logical volume (for a mainframe system) where Cache Residency is set. Define The setting status of Cache Residency.
Detailed information displays for this operation, as shown in the following table. Table 64 Detailed Info: New Installation Operation Item Description Micro Program The type of microprogram installed. Num. of Kind The number of each type of installed microprogram. Cache Residency Manager (Open DCR) Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Open DCR,,Normal end,,,Seq.
Item Description Num of DCR Settings The number of Cache Residencies set or canceled. Patch Edit Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install], Patch Edit,,Normal end,,,Seq.=xxxxx +Block=01 ++File=Old +++{Entry,Ctl.,Address,Old Data,New Data,Sum,Comment}= [{20,20,00000001,00000002,00000002,46,INLINE LCP}, {20,40,00000005,00000002,00000004,65,}], Num. of Data=2 ++File=New +++{Entry,Ctl.,Address,Old Data,New Data,Sum,Comment}= [{20,20,00000001,00000002,00000002,46, }], Num.
Item Description New Data The new data. Sum The sum value. Comment The comment information. Num. of Data The number of data. Num. of Blocks The number of blocks. Release LUSE Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Release LUSE,,Normal end,,,Seq.=xxxxx +LUSE(LDKC:CU:LDEV)=[0x00:0x00:0x00,0x00:0x01:0x00],Num. of LUSEs=2 [Install] Install function Release LUSE Release LUSE operation Normal end The operation has ended normally. Seq.
Restore Config. Restore Config. operation SVP&DKC SVP&DKC is the selected parameter. The restoration of configuration information for SVP and DKC. Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Example 2 user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Restore Config.,,Normal end,,,Seq.=xxxxx +{New Ver.,Old Ver.}={xx-xx-xx/xx,xx-xx-xx/xx} [Install] Install function Restore Config. Restore Config.
Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 69 Detailed Info: Set Battery Life Operation Item Description Use Battery Life The status of Battery life function set. Valid: Valid, Invalid: Invalid Date Indicates the date of the setting in YYYY/MM/DD format (YYYY: year, MM: month, DD: day). A hyphen (-) is indicated when the information is not set.
Set Command Device (CommandDev) Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Set CommandDev,,Normal end,,,Seq.=xxxxx +{LDKC:CU:LDEV,CommandDev}=[{0x00:0xXX:0xXX,Disable},{0x00:0xXX:0xXX,Enable}], Num. of LDEVs=2 [Install] Install function Set CommandDev Set CommandDev operation Normal end The operation has ended normally. Seq.
Detailed information displays for this operation, as shown in the following table. Table 72 Detailed Info: Set Command Device Security (CommandDevSec) Operation Item Description LDKC:CU:LDEV The LDKC, CU and LDEV numbers of the logical volume where the command device is set. CommandDev Indicates whether the command device security setting is enabled or disabled. Disable or Enable is output. Num. of LDEVs The number of logical volumes where the command device is set.
Install function Set Fibre Topology Set Fibre Topology operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 74 Detailed Info: Set Fibre Topology Operation Item Description Port The name of the port where the topology of Fibre Channel is set. Fabric Indicates whether the Fabric switch is enabled or disabled.
Detailed information displays for this operation, as shown in the following table. Table 75 Detailed Info: Set Host Mode Operation Item Description Port The name of the port where the host group is created. HostGrpID The host group number. Mode The host mode set. See the HP StorageWorks XP24000/XP20000 LUN Manager User's Guide for the meaning of the host mode number. Option[0:31] The host mode option set. Hexadecimal values are output.
Detailed information displays for this operation, as shown in the following table. Table 77 Detailed Info: Set IP Address Operation Item Description IP Add The IP address in SVP. Subnet The subnet mask in SVP. Use Duplex Indicates whether the Duplex setting in SVP is valid or invalid. Valid: Valid, Invalid: Invalid SVP Kind The kind of duplicated SVP. Master SVP: Master SVP, Standby SVP: Standby SVP. M-SVP IP Add The IP address of Master SVP. M-SVP Subnet The subnet mask of Master SVP.
Item Description Num. of Ports The number of ports where the LUN security setting is changed. Set Speed Mode Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Set Speed Mode,,Normal end,,,Seq.=xxxxx +CHA=CHA-1E ++{Port Block,Mode}=[{A,High Speed},{B,High Speed}Num. of Blocks=2 +CHA=CHA-1H ++{Port Block,Mode}=[{A,Standard},{B,High Speed}],Num. of Blocks=2 +Num. of CHAs=2 [Install] Install function Set Speed Mode Set Speed Mode operation Normal end The operation has ended normally. Seq.
Example 2 (The case of Synchro. Infor.) user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Set Subsystem Time,Synchro. Infor., Normal end,,,Seq.=xxxxx +{Use Synchro.,SNTP IP,SNTP Port,Time Zone,Check Time}={Valid,(123.456.789.123),100, Tokyo Standard Time,23} [Install] Install function Set Subsystem Time Set Subsystem Time operation TOD Change and Synchro. Infor TOD Change is the selected parameter for example 1, and Synchro. Infor is the selected parameter for example 2.
System Option Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],System Option,,Normal end,,,Seq.=xxxxx +Spare Disk Recover=Full Speed +Disk Copy Pace=Slower +Copy Operation(Correction Copy)=OFF +Copy Operation(Dynamic Sparing)=OFF +Read Configuration Data Mode=OFF +Power Lost Mode=Destage Mode +Cache Segment Size(SideA,SideB)=64(64,64) +Link Failure Threshold=10 +Power Supply Type=3-phase AC Box(40A) +{DKU,AC-BOX}=[{DKU-R1,1-phase AC Box(50A)}],Num.
Item Description Destage Mode: Set to Destage Mode Cache Segment Size The cache segment size SideA The size of the cache on Side A. SideB The size of the cache on Side B. Link Failure Threshold The threshold to report link failure. Power Supply Type The type of AC-BOX. Disk Unit (DKU) The Disk Unit (DKU) mounting location. AC-BOX The type of AC-BOX. Num. of AC-BOXs The number of AC-BOX. LDKC:CU: LDEV The LDKC number, the CU number and LDEV number.
System Tuning Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],System Tuning,,Normal end,,,Seq.=xxxxx +Serial No.=64040 +IP Address Mode=Based on Serial Number +IP Address=126.132.248 +Subnet Mask=255.0.0 +WDCP=ON +DDUMP=ON +Power Supply Type=3-phase AC Box(40A) +{DKU,AC-BOX}=[{DKU-R1,1-phase AC Box(50A)}],Num. of AC-BOXs=1 +{Port,CU Number,Emulation}=[{1E,-,I-2107},{3E,00:10-00:1F,I-2107},{5E,-,I-2107}, {7E,-,I-2107}],Num.
Item Description CU Number Indicates the range of the CU number which the port belongs. Emulation The emulation type. Num of Ports The number of ports. DKA The Disk Adapter (DKA) mounting location. Transfer Rate The Disk Adapter (DKA) transfer rate. Num.of DKAs The number of Disk Adapters (DKA). LDKC:CU The LDKC number and the CU number. LDEV The LDEV number. SSID The subsystem ID. Num of SSIDs The number of subsystem IDs.
Item Description Num. of Channel Adapters (CHA) The number of Channel Adapters (CHA). Example 2 (uninstalling a Disk Adapter (DKA), an ECC Group or an LDEV) user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Uninstall,,Normal end,,,Seq.=xxxxx +DKA=[DKA-1AL,DKA-1BL,DKA-2ML,DKA-2NL],Num. of DKAs=4 +DKU=[DKU-R1],Num. of DKUs=1 +FSW=[FSWR10-L,FSWR10-U,FSWR11-L,FSWR11-U,FSWR12-L,FSWR12-U,FSWR13-L,FSWR13-U, FSWR18-L,FSWR18-U,FSWR19-L,FSWR19-U,FSWR1A-L,FSWR1A-U,FSWR1B-L,FSWR1B-U], Num.
Item Description SPARE The spare drive number. Num. of SPAREs The number of spare drives. NOTE: Only the changed items will be output. The Detailed information for the recovery process will not be output when the uninstallation process is executed before the process has completed. However, the setting of the recovery process will be output as the Detailed information for the process when the uninstallation process is executed before the recovery process has not completed.
Item Description CLPR The CLPR number. Cache size The capacity of the cache memory allocated to CLPR. DCR size The capacity of Cache Residency allocated to CLPR. Extent Number The number of extents allocated to CLPR. Num. of CLPRs The number of CLPR. SM The mounting location of the shared memory. Slot The slot position of the shared memory module. Size The capacity of the shared memory module. Num. of SMMs The number of shared memory modules.
Detailed information displays for this operation, as shown in the following table. Table 87 Detailed Info: Uninstall Operation (Uninstalling a Shared Memory Module) Item Description SM The mounting location of the PCB for shared memory. Slot The slot position of the shared memory module. Size The capacity of the cache memory module. Num of SMMs The number of shared memory modules. PP Flag The flags of the options. Num of PP Flags The number of the flags of the options.
Detailed information displays for this operation, as shown in the following table. Table 88 Detailed Info: Uninstall Operation (Uninstalling a Power Supply) Item Description Redundant Power Supply The uninstalled additional cluster power supply. Num. of Redundant Power Supplies The number of additional cluster power supplies. Example 6 (uninstalling a battery) user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Uninstall,,Normal end,,,Seq.
Update Config operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 90 Detailed Info: Update Config Operation Item Description New Ver. The new version number. Old Ver. The old version number. Volume to Space Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Volume to Space,,Normal end,,,Seq.
Install Function
15 Logical Device (LDEV) Function Volume-Blockade Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[LDEV],Volume-Blockade,,Normal end,,,Seq.=xxxxx +LDKC:CU:LDEV=[0x00:0x00:0x01,0x00:0x00:0x02,0x00:0x00:0x03,0x00:0x00:0x04,0x00:0x00:0x05, 0x00:0x00:0x06,0x00:0x00:0x07,0x00:0x00:0x08,0x00:0x00:0x09,0x00:0x00:0x0A], [LDEV] Logical Device function Volume-Blockade Volume-Blockade operation Normal end The operation has ended normally. Seq.
user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[LDEV],Volume-Format,,Normal end,,,Seq.=xxxxx +LDKC:CU:LDEV=[0x00:0x00:0x01,0x00:0x00:0x02,0x00:0x00:0x03,0x00:0x00:0x04,0x00:0x00:0x05, 0x00:0x00:0x06,0x00:0x00:0x07,0x00:0x00:0x08,0x00:0x00:0x09,0x00:0x00:0x0A],Num. of LDEVs=XXX [LDEV] Logical Device function Volume-Format Volume-Format operation Normal end The operation has ended normally. Seq.
The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 94 Detailed Info: Volume-Format(H) Operation Item Description LDKC:CU:LDEV The LDKC number, the CU number and LDEV number. Num. of LDEVs The number of LDEVs being set. NOTE: The status does not change immediately after you execute an LDEV operation command.
NOTE: The status does not change immediately after you execute an LDEV operation command. As a result, errors may occur after you execute the command.
16 LUN Manager (LUNM) Function Add Host Group Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[LUNM],Add Host Group,,Normal end,,,Seq.=xxxxx +{Port,HostGrpID,HostGrpName}=[{XX,0xXXX,XXXXXXXXXXXXXXXX},{XX,0xXXX, XXXXXXXXXXXXXXXX}], Num.of Host Groups=2 [LUNM] LUN Manager function Add Host Group Add Host Group operation Normal end The operation has ended normally. Seq.
Add LU Path Add Logical Unit operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 97 Detailed Info: Add LU Path Item Description Port The name of the port where the host group is created. HostGrpID The host group number linked to the logical volume. LUN Indicates LUN of the logical volume linked to the host group.
Item Description HostGrpID The host group number where the host is registered. WWN Indicates WWN of the host bus adapter for the host registered in the host group. WWN is a 16-digit number in the hexadecimal format. Nickname The nickname of the host bus adapter for the host registered in the host group. Num. of WWNs The number of registered hosts (WWN). Auth Info (Host) Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[LUNM],Auth Info(Host),,Normal end,,,Seq.
Auth Info (Target) Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[LUNM],Auth Info(Target),,Normal end,,,Seq.=xxxxx +{Port,HostGrpID,UserName}=[{1E,0x01,user1},{3E,0x01,user2}],Num. of Info=2 [LUNM] LUN Manager function Add Info (Target) Add Info (Target) operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table.
Detailed information displays for this operation, as shown in the following table. Table 101 Detailed Info: Change Host Group Operation Item Description Port The name of the port where the host group is created. HostGrpID The host group number where the name or host modes have been changed. HostGrpName The name of the host group. If the name is changed, the name after change is indicated. Num. of Host Groups The number of host groups where the settings have been changed.
Delete Disk Controller (DKC) World Wide Name (WWN) Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[LUNM],Delete DKC WWN,,Normal end,,,Seq.=xxxxx +{Port,Delete WWN}=[{XX,0xXXXXXXXXXXXXXXXX},{XX,0xXXXXXXXXXXXXXXXX}],Num. of =2 [LUNM] LUN Manager function Delete DKC WWN Delete Disc Controller World Wide Name operation Normal end The operation has ended normally. Seq.
Detailed information displays for this operation, as shown in the following table. Table 104 Detailed Info: Delete Host Group Operation Item Description Port The name of the port where the host group deleted or initialized was created. HostGrpID The host group number deleted or initialized. Num. of Host Groups The number of host groups deleted or initialized. Delete Logical Unit (LU) Path Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[LUNM],Delete LU Path,,Normal end,,,Seq.
LUN Manager function Delete WWN Delete World Wide Name operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 106 Detailed Info: Delete WWN Operation Item Description Port The name of the port where the host deleted from host group was connected. HostGrpID The host group number where the host is deleted.
Item Description Authentication The setting status of user authentication. Enable: user authentication enabled, Disable: user authentication disabled Num. of Authentication The number of user authentication set. Set Channel Speed Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[LUNM],Set Channel Speed,,Normal end,,,Seq.=xxxxx +{Port,Speed(Gbps)}=[{XX,1},{XX,2},{XX,Auto},{XX,10}],Num.
Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 109 Detailed Info: Set Command Device (CommandDev) Operation Item Description LDKC:CU:LDEV The LDKC, CU and LDEV numbers of the logical volume where the command device setting is changed. CommandDev Indicates whether the command device setting is enabled or disabled.
Set Fibre-Channel Security Protocol (FCSP) Host Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[LUNM],Set FCSP Host,,Normal end,,,Seq.=xxxxx +{Port,HostGrpID,Kind,UserName,Change UserName}= [{1E,0x01,Add,1111111111111111,-}, {3E,0x01,Change,2222222222222222,3333333333333333},{5E,0x01,Delete, 4444444444444444,-}], Num. of Info=3 [LUNM] LUN Manager function Set FCSP Host Set FCSP Host operation Normal end The operation has ended normally. Seq.
Set FCSP Port Information operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 112 Detailed Info: Set Fibre-Channel Security Protocol (FCSP) Port Info Operation Item Description Port The name of the port where authentication parameter has been set.
Detailed information displays for this operation, as shown in the following table. Table 113 Detailed Info: Set Fibre-Channel Security Protocol (FCSP) Port Switch Operation Item Description Port The name of the port where authentication parameter has been set. Switch The setting status whether to execute authentication by port. Disable: Do not authenticate, Enable: Authenticate DH Group Not used. (fixed to 0) Auth The setting status of authentication method.
Item Description DH Group Not used. (fixed to 0) UserName The user name of the host group. Num. of Grps The number of host groups where authentication parameter has been set. Set Fibre Address Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[LUNM],Set Fibre Address,,Normal end,,,Seq.=xxxxx +{Port,Fibre Addr.}=[{XX,1},{XX,126}],Num.of Ports=2 [LUNM] LUN Manager function Set Fibre Address Set Fibre Address operation Normal end The operation has ended normally. Seq.
Value Add.* Value Add.* Value Add.* Value Add.
Value Add.* Value Add.* Value Add.* Value Add.* 32 B3 (31) 64 73 (63) 96 3C (95) - - * Addresses outside parentheses = arbitrated-loop physical address (AL-PA). Addresses in parentheses = loop IDs. Set Fibre Topology Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[LUNM],Set Fibre Topology,,Normal end,,,Seq.=xxxxx +{Port,Fabric,Connection}=[{XX,Enable,FC-AL},{XX,Disable,FC-AL},{XX,Enable,P-to-P}, {XX,Disable,P-to-P}], Num.
LUN Manager function Set Host Mode Set Host Mode operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 118 Detailed Info: Set Host Mode Operation Item Description Port The name of the port where the host group is created. HostGrpID The host group number. Mode The host mode set.
Set IP Address Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[LUNM],Set IP Address,,Normal end,,,Seq.=xxxxx +{Port,IPVersion,IPAddr,SubNetMask,GateWayAddr,DNSAddr}=[{1A,IPv4,(192.168.11.10), (255.255.255.0),(192.168.11.245),(192.168.250.100)}, -{3A,IPv4,(192.168.11.11),(255.255.255.0),(192.168.11.245),(192.168.250.100)}, {1B,IPv4,(192.168.100.100),(255.255.255.0),(192.168.100.245),(192.168.250.100)}, -{3B,IPv4,(192.168.254.128),(255.255.255.128),(192.168.254.245),(192.168.250.100)}], Num.
Set iSNS operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 121 Detailed Info: Set iSNS Operation Item Description PortID The name of the port where the iSNS server address has been set. iSNSPort The iSNS server port number set. iSNSAddr The iSNS server address set. Num.
Set Speed Mode Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[LUNM],Set Speed Mode,,Normal end,,,Seq.=xxxxxx +CHA=CHA-1EL ++{Port Block,Mode}=[{A,Standard},{B,High Speed/MIX}],Num. of Blocks=2 +Num. of CHAs=2 [LUNM] LUN Manager function Set Speed Mode Set Speed Mode operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table.
Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 124 Detailed Info: Set TCP/IP Port Operation Item Description Port The name of the port where the TCP/IP port number has been set. PortNumber The TCP/IP port number set. Num. of Ports The number of ports where the TCP/IP port number has been set.
LUN Manager (LUNM) Function
17 LUN Expansion (LUSE) Function Make LUSE Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[LUSE],Make LUSE,,Normal end,,,Seq.=xxxxx +LUSE(LDKC:CU:LDEV)=[[0x00:0x00:0x00,0x00:0x00:0x01,0x00:0x00:0x02, 0x00:0x00:0x03], [0x00:0x01:0x00,0x00:0x01:0x01,0x00:0x01:0x02,0x00:0x01:0x03]], Num. of LUSEs=2 [LUSE] Logical Unit Number Expansion function Make LUSE Logical Unit Number Expansion operation Normal end The operation has ended normally. Seq.
The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 126 Detailed Info: Release LUSE Operation Item Description LUSE(LDKC:CU:LDEV) The LDKC, CU and LDEV numbers of the top LDEV. Num. of LUSEs The number of LUSE volumes cancelled.
18 Maintenance Function Blockade Operation Example 1 (blocking a Cluster) user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Maintenance],Blockade,,Normal end,,,Seq.=xxxxx +Location=Cluster-1 Example 2 (blocking a PCB) user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Maintenance],Blockade,,Normal end,,,Seq.=xxxxx +PCB=[CHA-1P],Num. of PCBs=1+ PDEV=HDD00-01 Example 3 (blocking an LDEV) user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Maintenance],Blockade,,Normal end,,,Seq.=xxxxx +PG=[1-1],Num. of PGs=1 +PG=[E1-1],Num.
Item Description Num. of PCBs The number PCB to be blocked. PDEV The mounting location of the PDEV (physical device) to be blocked. PG The parity group number. Num. of PGs The number of parity groups. LDEV The LDEV number. Num. of LDEVs The number of LDEVs. Correction Copy Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Maintenance],Correction Copy,,Normal end,Seq.
Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 129 Detailed Info: Drive Interrupt Operation Item Description PDEV The mounting location of the PDEV (physical device). Format Operation NOTE: This log information indicates the completion of Format operation and does not indicate the completion of Format process.
Item Description Num. of LDEVs The number of LDEVs. NOTE: The status does not change immediately after you execute an LDEV operation command. As a result, errors may occur after you execute the command. Format Stop Operation NOTE: This log information is output when the format process is suspended. user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Maintenance],Format Stop,,Normal end,,,Seq.=xxxxx +PG=[1-1],Num. of PGs=1 +PG=[E1-1],Num. of PGs=1 (for an external volume) +PG=[V1-1],Num.
Recover Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Maintenance],Recover,,Normal end,,,Seq.=xxxxx +Location=Cluster-1 [Maintenance] Maintenance function Recover Recover operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table.
user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Maintenance], Replace,,Normal end,,,Seq.=xxxxx +PDEV=HDD00-01 +Copy=Restore Data +Diagnosis=Skip,Micro Program=Skip Example 5 ( Easy-replace of PDEV (physical device)) user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Maintenance], Replace,Easy-Replace,Normal end,Seq.=xxxxx +PDEV={HDDR03-01},Num. of PDEV=1 Example 6 (replacing a fibre switch) user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Maintenance], Replace,,Normal end,,,Seq.=xxxxx +FSW=[FSWR04-LL,FSWR05-LL],Num.
Item Description Num. of PCBs The number of PCBs to be replaced. Physical Device (PDEV) The mounting location of the PDEVs (physical devices) to be replaced. Copy The status of copy process when replacing physical devices (PDEV)s. This information is output only when replacing PDEVs. Restore Data: Data recovery from spare disk, Correction Copy: correction copy Diagnosis Diagnosis is output only when INLINE skip is selected when replacing PDEVs. This information is output only when replacing PDEVs.
Detailed information displays for this operation, as shown in the following table. Table 134 Detailed Info: Restore Operation Item Description PCB The mounting location of the PCB (Channel Adapter (CHA), Disk Adapter (DKA), cache memory (CM), shared memory (SM), cache switch (CSW), MIX or BASE) to be restored. PDEV The location of the PDEV to be restored. PG The parity group number. Num. of PGs The number of parity groups. LDEV The LDEV number. Num. of LDEVs The number of LDEVs.
Maintenance function Size Change Size Change operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 136 Detailed Info: Size Change Operation Item Description PCB The mounting location of the PCB (cache memory - CM) to be replaced. Num. of PCBs The number of PCBs to be replaced. SIZE The capacity of cache memory.
Detailed information displays for this operation, as shown in the following table. Table 137 Detailed Info: Drive Interrupt Operation Item Description PDEV The mounting location of the PDEV. Switch SVP Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Maintenance],Switch SVP,,Normal end,,,Seq.=xxxxx [Maintenance] Maintenance function Switch SVP Switch SVP operation Normal end The operation has ended normally. Seq.
user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Maintenance], Type Change,,Normal end,Seq.=xxxxx +PCB=[CHA-1P],Num. of PCBs=1 +TYPE=32FSR(FS2R) Fibre 16ch-8mp [Maintenance] Maintenance function Type Change Type Change operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table.
Detailed information displays for this operation, as shown in the following table. Table 139 Detailed Info: Verify Operation Item Description PG The parity group number. Num. of PGs The number of parity groups. LDEV The LDEV number. Num. of LDEVs The number of LDEVs. Verify Stop Operation NOTE: This log information is output when the format process is suspended. user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Maintenance],Verify Stop,,Normal end,,,Seq.=xxxxx +PG=[1-1],Num.
19 On-Demand (OND) Function Release Cache/CLPR Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[OND],Release Cache/CLPR,,Normal end,,,Seq.=xxxxx +Cache(MB)=258048 ++{CLPR,Cache(MB)}=[{01,4096},{02,4096},{03,4096},{04,4096},{05,4096},{06,4096},{07,4096}, {08,4096},{09,4096},{10,4096},{11,4096},{12,4096},{13,4096},{14,4096}, -{15,4096},{16,4096},{17,4096},{18,4096},{19,4096},{20,4096},{21,4096},{22,4096},{23,4096}, {24,4096},{25,4096},{26,4096},{27,4096},{28,4096},{29,4096},{30,4096}, -{31,4096}],Num.
On-Demand (OND) Function
20 Performance Monitor Function Monitoring Switch (S/W) Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[Perf Mon],Monitoring S/W,Enable 60sec,,Normal end,,,Seq.=xxxxx [Perf Mon] Performance Monitor function Monitoring S/W Monitoring Options operation Enable 60sec Enable 60 sec is the selected parameter. The operation uses the following parameters, as shown in the following table.
Enable 60 sec is selected as the parameter. The operation uses the following parameters, as shown in the following table. Table 143 Parameters: Monitoring Switch (SW) Operation Parameter Description Enable XXsec Monitoring is enabled and the gathering interval is set as XX sec. Disable Monitoring is disabled. Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295).
21 PORT Function Change Port Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[PORT],Change Port,,Normal end,,,Seq.=xxxxx +Attribute=RCU Target ++Port=[1E,3E,5E,7E], Num.of Ports=4 [PORT] PORT function Change Port Change Port operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table.
PORT Function
22 Optional Product (PP) KEY Function PP Disable chk Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[PP KEY],PP Disable chk,,Normal end,,,Seq.=xxxxx +{P.P.Name,Result}=[{JAVA API,Normal end}],Num. of PPs=1 [PP KEY] Optional Product License Key function PP Disable chk PP Disable File check operation Normal end The operation has ended normally. Seq.
Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 146 Detailed Info: PP Enable chk Operation Item Description P.P. Name The name of the enabled option. Result The result of disabled check. PP Install chk Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[PP KEY],PP Install chk,,Normal end,,,Seq.
Optional Product License Key function File Install chk File Install check operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 148 Detailed Info for File Install chk Operation Item Description File Name The name of the license key file used for installation. P.P. Name The name of the installed option.
SLPR PP Change Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[PP KEY],SLPR PP Change,,Normal end,,,Seq.=xxxxx +{P.P. Name,SLPR#,License Capa(GB)}=[{JAVA API,XX,ZZZZZ00},{LUN Manager,XX,ZZZZZ00}], Num. of PPs=2 [PP KEY] Optional Product License Key function SLPR PP Change SLPR PP Change operation Normal end The operation has ended normally. Seq.
23 Remote Control Unit (RCU) Function Add Path Operation Example 1 (CU Free is used) user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[RCU],Add Path,,Normal end,,,Seq.=xxxxx +{S/N,LDKC,Path Gr. ID,Controller ID}={99999,0x00,Default,4} ++{MCU Port,RCU Port}=[{1E,3E},{5E,7E},{1F,3F},{5F,7F},{1G,3G},{5G,7G},{1H,3H},{5H,7H}], Num. of Port Pairs=8 Example 2 (CU Free is not used) user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[RCU],Add Path,,Normal end,,,Seq.
Item Description RCU Port The port number of RCU. Num. of Port Pairs The number of port pairs set. Add RCU Operation Example 1 (CU Free is used) user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[RCU],Add RCU,,Normal end,,,Seq.=xxxxx +{S/N, MCU LDKC,RCU LDKC,Path Gr. ID,Controller ID,Min. Path,MIH Time(s), Round Trip Time(ms),Incident,FREEZE}={99999,0x00,0x00,Default,4,08,015,001, only to RCU host,Disable} ++{MCU Port,RCU Port}=[{1E,3E},{5E,7E},{1F,3F},{5F,7F},{1G,3G},{5G,7G},{1H,3H},{5H,7H}], Num.
Item Description MCU The CU number of the connected CU. RCU The CU number of the paired CU. SSID The SSID of the registered RCU. MCU Port The port number of MCU. RCU Port The port number of the registered RCU. Min. Path The number of set minimum paths. MIH Time(s) The value of set RIO MIH (Remote I/O Missing Interrupt Handler) timer (wait time until data copy from MCU to RCU is completed). The unit is second.
Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 153 Detailed Info: Change RCU Option Item Description S/N Indicates a serial number of the RCU device where the RCU option setting is changed. LDKC The LDKC number of the paired LDKC. Path Gr. ID The RCU path group ID where the RCU optional setting is changed.
++{MCU Port,RCU Port}=[{1E,3E},{5E,7E},{1F,3F},{5F,7F},{1G,3G},{5G,7G},{1H,3H},{5H,7H}], Num. of Port Pairs=8 [RCU] Remote Control Unit function Delete Path Delete Path operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table.
Delete RCU Delete Remote Control Unit operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 155 Detailed Info: Delete RCU Operation Item Description S/N The serial number of the device of RCU deleted. LDKC The LDKC number of the paired LDKC. Path Gr. ID The path group ID of the RCU deleted.
24 HP XP Business Copy Software Function Change Reserve Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[BC],Change Reserve,,Normal end,,,Seq.=xxxxx +Attribute=Set ++{VOL(LDKC:CU:LDEV),Result}=[{0xZZ:0xXX:0xYY,Normal end},{0xZZ:0xXX:0xYY, Error(xxxx-yyyy)}],Num. of Vols=2 [BC] HP XP Business Copy Software function Change Reserve Change Reserve operation Normal end The operation has ended normally. Seq.
HP XP Business Copy Software function Initialize Initialize operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Option Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[BC],Option,,Normal end,,,Seq.=xxxxx +Swap & Freeze=Enable,HOST I/O Performance=Enable,Reserve03=Enable,(snip), Reserve32=Disable [BC] HP XP Business Copy Software function Option Option operation Normal end The operation has ended normally. Seq.
HP XP Business Copy Software function Pair Create Paircreate operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 158 Detailed Info: Pair Create Operation Item Description Copy Pace The set copy speed.
Detailed information displays for this operation, as shown in the following table. Table 159 Detailed Info: Pairresync Operation Item Description Copy Pace The set copy speed. Faster: High speed, Medium: Medium speed, Slower: Low speed Resync Type The type of resynchronization.
Item Description Medium: medium speed Slower: Low speed Split Type The split type. Quick Split: Pair split by background copy Steady Split: Pair split by update copy P-VOL(LDKC:CU:LDEV) The LDKC, CU and LDEV number of the primary volume in the split pair. S-VOL(LDKC:CU:LDEV) The LDKC, CU and LDEV number of the secondary volume in the split pair. MU The MU number of the split pair. Result The result of operation.
Item Description xxxx: Part code, yyyyy: Error code Num. of Pairs The number of suspended pairs. Pairsplit-S Operation Example 1 (HP XP Business Copy Software is used) user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[BC],Pairsplit-S,,Normal end,,,Seq.=xxxxx +{P-VOL(LDKC:CU:LDEV),S-VOL(LDKC:CU:LDEV),Result}=[{0xAA:0xBB:0xCC,0xDD:0xEE:0xFF,Normal end}, {0xAA:0xBB:0xCC,0xDD:0xEE:0xFF,Error(xxxx-yyyy)}],Num.
25 ShadowImage (SI) for Mainframe Function Add Pair Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[SI],Add Pair,,Normal end,,,Seq.=xxxxx +Copy Pace=Faster ++{S-VOL(LDKC:CU:LDEV),T-VOL(LDKC:CU:LDEV),Result}=[{0xXX:0xAA:0xBB,0xYY:0xCC:0xDD,0,Normal end}, {0xXX:0xAA:0xBB,0xYY:0xCC:0xDD,1,Error(xxxx-yyyy)}],Num. of Pairs=2 [SI] ShadowImage for Mainframe function (for the IBM z/OS) Add Pair Add Pair operation Normal end The operation has ended normally. Seq.
Change Reserve Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[SI],Change Reserve,,Normal end,Seq.=xxxxx +Attribute=Set ++{VOL(LDKC:CU:LDEV),Result}=[{0xZZ:0xXX:0xYY,Normal end},{0xZZ:0xXX:0xYY, Error(xxxx-yyyy)}],Num.of Vols=2 [SI] ShadowImage for Mainframe function (for the IBM z/OS) Change Reserve Change Reserve operation Normal end The operation has ended normally. Seq.
Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 165 Detailed Info: Consistency Group (CTG) Operation Item Description CTG The consistency group number. Command Indicates whether the CT group (consistency group) is newly registered or the existing CT group is deleted. Add: Registration of CT group, Delete: deletion of CT group Result The result of operation.
Item Description Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Pairs The number of deleted pairs. Initialize Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[SI],Initialize,,Normal end,,,Seq.=xxxxx [SI] ShadowImage for Mainframe function (for the IBM z/OS) Initialize Initialize operation Normal end The operation has ended normally. Seq.
Item Description HOST I/O Performance Indicates whether the host I/O option is enabled or disabled. FCv2 Slower Copy1 Indicates whether the FCv2 Slower Copy1 option is enabled or disabled. FCv2 Slower Copy2 Indicates whether the FCv2 Slower Copy2 option is enabled or disabled. Reserve X Reserved items. X is a number from 05 to 32. Enable: Option is enabled, Disable: Option is disabled. Enable: Option is enabled, Disable: Option is disabled. Enable: Option is enabled, Disable: Option is disabled.
Item Description xxxx: Part code, yyyyy: Error code Num. of Pairs The number of resynchronized pairs. Split Pair Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[SI],Split Pair,,Normal end,,,Seq.=xxxxx +Copy pace=Faster,Split Type=QuickSplit ++{S-VOL(LDKC:CU:LDEV),T-VOL(LDKC:CU:LDEV),Result}=[{0xXX:0xAA:0xBB,0xYY:0xCC:0xDD,0, Normal end},{0xXX:0xAA:0xBB,0xYY:0xCC:0xDD,1,Error(xxxx-yyyy)}],Num.
Suspend Pair Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[SI],Suspend Pair,,Normal end,,,Seq.=xxxxx +{S-VOL(LDKC:CU:LDEV),T-VOL(LDKC:CU:LDEV),Result}=[{0xXX:0xAA:0xBB,0xYY:0xCC:0xDD, Normal end},{0xXX:0xAA:0xBB,0xYY:0xCC:0xDD,Error(xxxx-yyyy)}],Num. of Pairs=2 [SI] ShadowImage for Mainframe function (for the IBM z/OS) Suspend Pair Suspend Pair operation Normal end The operation has ended normally. Seq.
ShadowImage (SI) for Mainframe Function
26 HP XP Snapshot Function Pairsplit-S Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Snapshot],Pairsplit-S,,Normal end,,,Seq.=xxxxx +{P-VOL(LDKC:CU:LDEV),S-VOL(LDKC:CU:LDEV),MU,Result}=[{0xAA:0xBB:0xCC,0xDD:0xEE:0xFF,00, Normal end},{0xAA:0xBB:0xCC,0xDD:0xEE:0xFF,01,Error(xxxx-yyyy)}],Num. of Pairs=2 [Snapshot] HP XP Snapshot function Pairsplit-S Pairsplit-S operation Normal end The operation has ended normally. Seq.
HP XP Snapshot Function
27 SNMP Function Set SNMP Agent Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[SNMP],Set SNMP Agent,,Normal end,,,Seq.=xxxxx +Install=Disable +Manager=[(158.214.133.001),(158.214.133.002),(158.214.133.003),(158.214.133.004), (158.214.133.005),(158.214.133.006),(158.214.133.007),(158.214.133.008), (158.214.133.009), -(158.214.133.010),(158.214.133.011),(158.214.133.012),(158.214.133.013), (158.214.133.014), (158.214.133.015),(158.214.133.016),(158.214.133.017),(158.214.133.018), (158.214.133.
Detailed information displays for this operation, as shown in the following table. Table 172 Detailed Info: Set SNMP Agent Operation Item Description Install The setting status of SNMP Agent. Enable, Disable Manager The IP address of the registered SNMP manager. Num. of Managers The number of the registered SNMP managers. Community The registered community name. Trap The IP address where the trap of community is reported. Num. of Traps The number of traps reported. Num.
28 HP XP Continuous Access Software Function Add Consistency Group (CTG) Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Cnt Ac],Add CTG,,Normal end,,,Seq.=xxxxx +{LDKC,CTG,Path,Offloading(s),Inflow Control,Copy Pending(min.),RCU Ready(min.)}= {0x00,0x00,Fibre,090,Enable,05,05} [Cnt Ac] HP XP Continuous Access Software function Add CTG Add Consistency Group operation Normal end The operation has ended normally. Seq.
Change Async Option Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Cnt Ac],Change Async Option,,Normal end,,,Seq.=xxxxx +{CLPR,Rate(%),Delay Start(%),Delay Increase(%)}={00,050,030,040} [Cnt Ac] HP XP Continuous Access Software function Change Async Option Change Async Option operation Normal end The operation has ended normally. Seq.
Detailed Information Detailed information displays for this operation, as shown in the following table. Table 175 Detailed Info: Change Consistency Group (CTG) Option Item Description LDKC The LDKC number. CTG The consistency group number of the consistency group (CT group) where the option is changed. Offloading(s) The value set to the monitoring time of transfer to the side file. The unit is second. Inflow Control Indicates whether the inflow control to the cache is enabled or disabled.
Item Description Path Blockade Watch(s) The path blockade watch period set. The unit is second. Path Blockade SIM Watch(s) The path blockade SIM watch period set. The unit is second. Service SIM Indicates whether the remote copy related SIM is reported or not. Report, Not Report Parallel Initial Copy(CU) Indicates whether the parallel operation of initial copy by CU is enabled or not. LDKC The LDKC number. CU The CU number of the connected CU.
Detailed information displays for this operation, as shown in the following table. Table 177 Detailed Info: Change Pair Option Operation Item Description P-VOL(Port-G-ID-LUN) The port number, host group number and LUN of the primary volume where the pair option is changed sequentially. Fence Level The changed fence level (the condition that MCU rejects Write to the primary volume).
Paircreate Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Cnt Ac],Paircreate,,Normal end,,,Seq.=xxxxxx +{P-VOL(Port-G-ID-LUN),S-VOL(Port-G-ID-LUN),S/N,LDKC,ID,ControllerID,Type, Initial Copy, Fence Level,Copy Pace,Priority,Diff,CTG, Error Level,Result}= -{1A-0x00-0x000,GR-0xFE-0x3FF,99999,0x00,Default,4,Async,Entire,Never,15,032, Auto,0x00, Group,Normal End}, (snip) -(snip), Num.
Item Description Copy Pace The initial copy speed set (the number of tracks you can copy at one time). Priority The priority of the set initial copy operation (scheduling order). Diff The unit of the differential management set. Auto, Cylinder, Track CTG The consistency group number of the consistency group (CT group) that the created pair belongs to. This value is output when the asynchronous pair is created only. Error Level The error level set (handling if trouble occurs).
Item Description S-VOL(Port-G-ID-LUN) The port number, host group number and LUN of the secondary volume in the restored pair sequentially. Fence Level The fence level set (the condition that MCU rejects Write to the primary volume). Never: No condition, Data: S-VOL data, Status: S-VOL status Copy Pace The initial copy speed set (the number of tracks you can copy at a time). Priority The priority of restoring operation set (scheduling order).
Detailed information displays for this operation, as shown in the following table. Table 181 Detailed Info: Pairsplit-r Operation Item Description P-VOL(Port-G-ID-LUN) The port number, host group number and LUN of the primary volume in the split pair sequentially. S-VOL(Port-G-ID-LUN) The port number, host group number and LUN of the secondary volume in the split pair sequentially. Type The volume type of the volume on the primary site.
Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 182 Detailed Info: Pairsplit-S Operation Item Description P-VOL(Port-G-ID-LUN) The port number, host group number and LUN of the primary volume in the deleted pair sequentially. S-VOL(Port-G-ID-LUN) The port number, host group number and LUN of the secondary volume in the deleted pair sequentially.
Sequence number of log information (0000000000 to 4294967295) Detailed Information No detailed information displays for this operation.
HP XP Continuous Access Software Function
29 TrueCopy (TC) for Mainframe Function Add Consistency Group (CTG) Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[TC],Add CTG,,Normal end,,,Seq.=xxxxxx +{LDKC,CTG,Path,Offloading(min.),Inflow Control,Copy Pending(min.),RCU Ready(min.), Timer Type}= {0x00,0x00,Fibre,005,Enable,05,05,System} [TC] TrueCopy for Mainframe function (for IBM z/OS) Add CTG Add Consistency Group operation Normal end The operation has ended normally. Seq.
Item Description System: System timer, Local: Local timer, None: No timer (system timer) Add Pair Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00, [TC],Add Pair,,Normal end,,,Seq.=xxxxxx +{M-VOL(LDKC:CU:LDEV),R-VOL(LDEV),S/N,LDKC,SSID,ControllerID,Type, Initial Copy, Fence Level,Copy Pace, Priority,Diff,CFW,DFW,CTG, Error Level,Result}= -{0x00:0x00:0x00,0xFF,99999,0x00,0x0004,4,Async,Entire,Never,15,032,Auto, Only M-VOL,-,0x00,Group,Normal End}, (snip) -(snip), Num.
Item Description Copy Pace The initial copy speed set (the number of tracks you can copy at a time). Priority The priority of the initial copy operation set (scheduling order). Diff The unit of the differential management set: Auto, Cylinder, Track CFW Indicates whether the setting to copy the CFW data to the remote volume is enabled or not.
Detailed information displays for this operation, as shown in the following table. Table 185 Detailed Info: Change Async Option Item Description CLPR The CLPR number. Rate(%) The specified pending update data rate. Change Consistency Group (CTG) Option Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[TC], Change CTG Option,,Normal end,,,Seq.=xxxxx +{LDKC,CTG, Offloading(min.),Inflow Control,Copy Pending(min.),RCU Ready(min.
Change Option Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[TC],Change Option,,Normal end,,,Seq.
Item Description SCP Time(s) The SCP delay time when the pair is suspended. The unit is second. Parallel Initial Copy(CU) The number of parallel operation of initial copy by CU. (1 to 16) Num. of CUs The number of CUs set. Change Pair Option Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[TC],Change Pair Option,,Normal end,Seq.
Item Description Result The result of operation. Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Pairs The number of changed pairs. Clear SIM Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[TC],Clear SIM,,Normal end,,,Seq.=xxxxxx [TC] TrueCopy for Mainframe function (for IBM z/OS) Clear SIM Clear Service Information Message (SIM) operation Normal end The operation has ended normally. Seq.
Sequence number of log information (0000000000 to 4294967295) Delete Pair Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[TC],Delete Pair,,Normal end,,,Seq.=xxxxxx +{VOL(LDKC:CU:LDEV),PairVOL(LDEV),Type,Mode,Range,Result}= -{0x00:0x00:0x00,0xFF,M-VOL,Normal,Group,Normal End},{0x00:0x01,Normal,Group, Normal End}, {0x00:0x02,Normal,Group,Normal End},(snip) -(snip), Num.
Resume Pair Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[TC],Resume Pair,,Normal end,,,Seq.=xxxxxx +{M-VOL(LDKC:CU:LDEV), R-VOL(LDEV),Fence Level,Copy Pace,Priority,Range, Error Level, Result}= -{0x00:0x00:0x00,0xFF,Never,15,256,Group,Group,Normal End},{0x00:0x01,Never, 15,256,Group, Group,Normal End}, (snip) -(snip), Num. of Pairs=xx [TC] TrueCopy for Mainframe function (for IBM z/OS) Resume Pair Resume Pair operation Normal end The operation has ended normally. Seq.
Item Description Result The result of operation. Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Pairs The number of restored pairs. Script Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[TC],Script Operation,Run,,Normal end,Seq.=xxxxxx +FileName=script.spt [TC] TrueCopy for Mainframe function (for IBM z/OS) Script Operation Script Operation operation Run Run is selected as the parameter.
[TC] TrueCopy for Mainframe function (for IBM z/OS) Start Pair Start Pair operation. This operation is executed automatically when you use Add Pair or Resume Pair, or change the mode to Modify (first time only), in the Pair Operation window. Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information No detailed information displays for this operation.
Item Description M-VOL Failure: Main volume write is disabled R-VOL: Main volume write is enabled Range The suspend range set. This value is output when the asynchronous pair is split only. Volume: Volume (specified TrueCopy for Mainframe Asynchronous pairs only are suspended) Group: Group (all other TrueCopy for Mainframe Asynchronous pairs in the same consistency group as the specified pairs are suspended) Mode The setting of unreflected data handling.
30 HP XP Continuous Access Journal Software Function Journal-Option Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Cnt Ac-J],Journal-Option,,Normal end,,,Seq.=xxxxx +{LDKC,JNLG,MetaData Ratio,Extent,Data Overflow Watch(s),Inflow Control,Copy Pace, Path Watch Time,Forward Path Watch Time,Use of Cache,Speed of Line(Mbps), Delta resync Failure,Result}={0x00,0x00,32,32,20,No,150,30,Yes,Not Use,256,Entire, Normal end}, -{0x00,0x01,32,32,20,No,150,30,No,Use,256,Entire,Normal end},Num.
Item Description Copy Pace The speed of initial copy. 150: Low speed. 500: Medium speed. 1500: High speed Path Watch Time The path blockade watch period set. The unit is minutes, hours or days. If it is set to 30 minutes, it will be 30(min). Forward Path Watch Time Whether to transfer the path blockade watch period set to the master journal group to the restore journal group. Yes: Transfer. No: Do not transfer. Use of Cache Whether to store the journal data in the restore journal group in cache.
Parameter Description Delete The journal volume is deleted. Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed information Detailed information displays for this operation, as shown in the following table. Table 197 Detailed Info: Journal-Vol Operation Item Description LDKC The journal group's LDKC number JNLG The journal group number. LDKC:CU:LDEV The LDKC, CU and LDEV numbers. Result The result of operation.
Detailed information displays for this operation, as shown in the following table. Table 198 Detailed Info: Journal-Vol Operation Item Description LDKC The LDKC number that the journal group belongs. JNLG The journal group number. Result The result of operation. Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of JNL Grps The number of journal groups.
Item Description Priority The priority of copy. CTG The consistency group ID. Initial Copy Indicates whether initial copy or paircreate operation for Delta resync is executed or not. Entire: execute initial copy, None: do not execute initial copy, Delta: execute paircreate operation for Delta resync M-JNLG The master journal group. R-JNLG The restore journal group. Path Gr. ID The path group ID (Default fixed) specified for the storage system.
Detailed information displays for this operation, as shown in the following table. Table 200 Detailed Info: Pairresync Operation Item Description P-VOL(Port-G-ID-LUN) The port number, host group number and LUN of the primary data volume. S-VOL(Port-G-ID-LUN) The port number, host group number and LUN of the secondary data volume. MirrorID The mirror ID. S/N The serial number of the logical device storage system. CTRLID The controller ID. Priority The priority of copy.
Pairsplit-r operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 201 Detailed Info: Pairsplit-r Operation Item Description P-VOL(Port-G-ID-LUN) The port number, host group number and LUN of the primary data volume. S-VOL(Port-G-ID-LUN) The port number, host group number and LUN of the secondary data volume.
Pairsplit-S operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 202 Detailed Info: Pairsplit-S Operation Item Description P-VOL(Port-G-ID-LUN) The port number, host group number and LUN of the primary data volume. S-VOL(Port-G-ID-LUN) The port number, host group number and LUN of the secondary data volume.
The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 203 Detailed Info: Pair-Option Operation Item Description P-VOL(Port-G-ID-LUN) The port number, host group number and LUN of the primary data volume. S-VOL(Port-G-ID-LUN) The port number, host group number and LUN of the secondary data volume. MirrorID The mirror ID.
Detailed information displays for this operation, as shown in the following table. Table 204 Detailed Info: System-Option Operation Index Description Max Initial Copy Indicates the number of volumes that can be copied at a time by one initial copy. No detailed information.
31 Universal Replicator (UR) for Mainframe Function Add-Pair Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[UR],Add-Pair,,Normal end,,,Seq.=xxxxxx +{P-VOL(LDKC:CU:LDEV),S-VOL(LDKC:CU:LDEV),MirrorID,S/N,CTRLID,Priority, Initial Copy, M-JNLG,R-JNLG,Path Gr.ID,Error Level,CFW,Result}=[{0x00:0x00:0x00,0x00:0x20:0x00,0x00, 65432,5,32,Entire,0x02,0x00,Default,Group,Copy to S-VOL,Normal end}, -{0x00:0x00:0x01,0x00:0x20:0x01,0x00,65432,5,32,Entire,0x02,0x00,Default,Group, Copy to S-VOL, Normal end}],Num.
Item Description Delta: execute paircreate operation for Delta resync M-JNLG The master journal group number. R-JNLG The restore journal group number. Path Gr. ID The path group ID (Default fixed) set for the storage system. Error Level The error level: Group: Group level, Volume: Volume level CFW Indicates whether the cache-fast-write data is copied to the secondary data volume is enabled or not. Only P-VOL: Not copied, Copy to S-VOL: Copied Result The result of operation.
Delete-Pair operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed information Detailed information displays for this operation, as shown in the following table. Table 206 Detailed Info: Delete-Pair Operation Item Description P-VOL(LDKC:CU:LDEV) The LDKC, CU and LDEV numbers of the primary data volume. S-VOL(LDKC:CU:LDEV) The LDKC, CU and LDEV numbers of the secondary data volume. MirrorID The mirror ID.
Edit-EXCTG Extended consistency group operation Add Add is selected as the parameter. This operation uses the following parameters: Table 207 Parameters: Edit-Extended Consistency Group (EXCTG) Operation Parameter Description Add Add journal groups to the extended consistency group. Remove Remove journal groups from the extended consistency group. Normal end The operation has ended normally. Seq.
Journal-Option Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[UR],Journal-Option,,Normal end,Seq.=xxxxx +{LDKC,JNLG,MetaData Ratio,Extent,Data Overflow Watch(s),Inflow Control,Copy Pace, Timer Type, Path Watch Time,Forward Path Watch Time,Use of Cache,Speed of Line(Mbps),Delta resync Failure,Result}= -{0x00,0x00,32,32,20,No,150,Local,30(min.),Yes,Not Use,256,Entire,Normal end}, (snip), {0x00,0x02,32,32,20,No,150,Local,30(min.),Yes,Not Use,256,Entire,Normal end}, Num.
Item Description Use of Cache Indicates whether to store the journal data in the restore journal group in cache. Use: Store the journal data in cache. Not Used: Store the journal data in journal volume. Speed of Line(Mbps) The transfer speed of the communication line. The unit is megabits per second (Mbps). Delta resync Failure Indicates the operation mode when Delta resync operation have failed. Entire: Copy the entire data volume, None: Do not copy the data volume Result The result of operation.
Detailed information displays for this operation, as shown in the following table. Table 211 Detailed Info: Journal-Vol Operation Item Description LDKC The journal group's LDKC number. JNLG The journal group number. LDKC:CU:LDEV The LDKC, CU and LDEV numbers. Result The result of operation. Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of JNL Grps The number of journal groups.
Detailed information displays for this operation, as shown in the following table. Table 213 Detailed Info: Journal-Vol Operation Item Description LDKC The journal group's LDKC number. JNLG The journal group number. Result The result of operation. Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of JNL Grps The number of journal groups. Pair-Option Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[UR],Pair-Option,,Normal end,,,Seq.
Item Description Error Level The error level. Group: Group level, Volume: Volume level CFW Indicates whether the setting to copy the CFW data to the remote volume is enabled or not. Only M-VOL: Copy to the main volume only is enabled. Copy To R-VOL: Copy to the main and remote volume is enabled. Result The result of operation. Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Pairs The number of pairs.
Item Description Range The range to restore the pair. Group: Group range. Volume: Volume range M-JNLG The master journal group number. R-JNLG The restore journal group number. Error Level The error level. Group: Group level. Volume: Volume level Resync Mode Indicates the resync mode. Normal: normal resync, Delta: delta resync, Return to standby: return to standby status Result The result of operation.
Item Description S-VOL(LDKC:CU:LDEV) The LDKC, CU and LDEV numbers of the secondary data volume. MirrorID The mirror ID. S/N The serial number of the logical device storage system. CTRLID The controller ID. Type Indicates whether the split data volume is a primary or secondary data volume. P-VOL: Primary, S-VOL: Secondary S-VOL Write Indicates whether writing to the secondary volume is enabled or not. Disable: Disabled, Enable: Enabled Range The split range.
Detailed information displays for this operation, as shown in the following table. Table 217 Detailed Info: System-Option Operation Item Description Max Initial Copy The number of volumes you can copy at a time during an initial copy operation. LDKC:CU The LDKC and CU numbers. Change SIM Report Whether to report SIM to the host or not. Report. Not report. Num of CUs The number of CUs (fixed to 64).
32 HP XP External Storage Software Function Add-Vol Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Ext Stor],Add-Vol,,Normal end,,,Seq.=xxxxx [Ext Stor] HP XP External Storage Software function Add-Vol Add-Vol operation (add volume) Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Alternate-Path Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Ext Stor],Alternate-Path,,Normal end,,,Seq.
Change-CacheMode Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Ext Stor],Change-CacheMode,Enable,Normal end,,,Seq.=xxxxx +{Group,Result}=[{E1-1,Normal End},{E1-2,Error(605-3003)},{E1-3,Normal End}, {E1-4,Normal End}],Num. of Groups=XXX [Ext Stor] HP XP External Storage Software function Change-CacheMode Change-CacheMode operation Enable Enable is the selected parameter. The operation uses the parameters shown in the following table.
Check-Paths Check-Paths operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) NOTE: The status does not change immediately after you perform the Check-Paths operation. As a result, errors may occur after you perform the operation. ChkPath-RestoreVol Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Ext Stor],ChkPath-RestoreVol,,Normal end,Seq.
NOTE: The status does not change immediately after you perform the ChkPath-RestoreVol operation. As a result, errors may occur after you perform the operation. Delete-Vol (Force) Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Ext Stor],Delete-Vol(Force),,Normal end,,,Seq.=xxxxx [Ext Stor] HP XP External Storage Software function Delete-Vol (Force) Delete-Vol (Force) operation (delete volume) Normal end The operation has ended normally. Seq.
Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) NOTE: The status does not change immediately after you perform the Disconnect-Paths operation. As a result, errors may occur after you perform the operation. Disconnect-Volume Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Ext Stor],Disconnect-Volume,,Normal end,,,Seq.
Inflow-Control Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Ext Stor],Inflow-Control,Enable,Normal end,,,Seq.=xxxxx +{Group,Result}=[{E1-1,Normal End},{E1-2,Error(605-3003)},{E1-3,Normal End}, {E1-4,Normal End}],Num. of Groups=XXX [Ext Stor] HP XP External Storage Software function Inflow-Control Inflow-Control operation Enable Enable is selected as the parameter. The operation uses the parameters shown in the following table.
HP XP External Storage Software function WwnTimer WwnTimer operation (World Wide Name) Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 224 Detailed Info: WWN Timer Operation Item Description WWN The WWN of the external subsystem. I/O-TOV The I/O time over value set.
HP XP External Storage Software Function
33 Virtual LVI / Virtual LUN (VLL) Function Install Customized Volume Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[VLL],Install CV,,Normal end,,,Seq.=xxxxxx +{PG,LDKC:CU:LDEV,Start LBA,Emulation,Size,Unit,System Disk }=[{XX-XX-(X), 0xXX:0xXX:0xXX, XXXXXXXX,OPEN-V,XXXXXXXX,KB,Disable}, {X-X-(X),0xXX:0xXX:0xXX,XXXXXXXX,OPEN-V,XXXXXXXX,KB,Disable}],Num.
Item Description Start LBA The start LBA. NOTE: A hyphen (-) is output when not specified. Emulation The emulation type. Size The user-specified capacity. Unit The unit of the CV capacity. NOTE: The output unit is different according to the setting. KB: For open-system volume Cyl: For mainframe-system volume LBA: When LBA is specified System Disk Indicates system disk status. Enable: Enabled, Disable: Disabled Num. of LDEVs The number of LDEVs.
Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 228 Detailed Info: Make Volume Operation Item Description PG The parity group number. NOTE: The parity group number whose first letter is E indicates that an external volume is present in the parity group. LDKC:CU:LDEV The LDKC, CU and LDEV numbers. Emulation The emulation type. Size The user-specified capacity.
Detailed information displays for this operation, as shown in the following table. Table 229 Detailed Info: Set SSID Operation Item Description SSID The SSID number. NOTE: The SSID specified when Volume Initialize or Make Volume is executed is also output. LDKC:CU:LDEV The LDKC, CU and LDEV numbers. Num. of SSIDs The number of SSIDs. Volume Initialize Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[VLL],Volume Initialize,,Normal end,,,Seq.
Item Description NOTE: The parity group number whose first letter is E indicates that an external volume is present in the parity group. LDKC:CU:LDEV The LDKC, CU and LDEV numbers. NOTE: None is output when the LDKC, CU and LDEV numbers are not specified. Num. of PGs The number of parity groups. Volume to Space Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[VLL],Volume to Space,,Normal end,,,Seq.=xxxxxx +{PG,LDKC:CU:LDEV}=[{XX-XX-(X),0xXX:0xXX:0xXX},{XX-XX-(X),0xXX:0xXX:0xXX}], Num.
Virtual LVI / Virtual LUN (VLL) Function
34 HP XP Auto LUN Software Function Del Auto Plan Log Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Auto LUN],Del Auto Plan Log,,Normal end,,,Seq.=xxxxxx [Auto LUN] HP XP Auto LUN Software function Del Auto Plan Log Del Auto Plan Log operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Del Migration Log Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Auto LUN],Del Migration Log,,Normal end,,,Seq.
HP XP Auto LUN Software function Set Migration Vol Set Migration Vol operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table.
The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 234 Detailed Info: Set Reserved Vol Operation Item Description Set The operation executed to the logical volume. Normal: Set to the normal volume Reserved: Set to the reserved volume of HP XP Auto LUN Software LDKC:CU:LDEV The ID of the logical volume which the setting is changed.
HP XP Auto LUN Software Function
35 HP XP Disk/Cache Partition Function Set Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[DCPart],Set,,Normal end,,,Seq.=xxxxxx +Delete SLPR=[xx,xx],Num. of SLPRs=xx +Delete CLPR=[xx,xx],Num. of CLPRs=xx +SLPR=xx:xxxxxxxxxxxxxx,Operation=xxxxx ++Port=[CLx-x,CLx-x],Num. of Ports=xx ++CU=[0xXX:0xXX,0xXX:0xXX] ,Num. of CUs=xx ++SSID=[0xXXXX,0xXXXX],Num. of SSIDs=xx ++CLPR=xx:xxxxxxxxxxxxxx,Cache(MB)=xxxxx,Cache Residency(MB)=xxxx, Num. of Cache Residency Areas=xxxx +++PG=[xx-xx,xx-xx],Num.
Item Description Num. of Ports The number of ports belonging to SLPR. CU The LDKC and CU number of the CU belonging to SLPR. Num. of CUs The number of CUs belonging to SLPR. SSID Indicates SSID belonging to SLPR. A space is output if SLPR0. Num. of SSIDs The number of SSIDs belonging to SLPR. 0 (zero) is output if SLPR0. CLPR The CLPR number and the CLPR name belonging to SLPR. Cache(MB) The cache capacity set. The unit is megabyte (MB). Cache Residency(MB) The Cache Residency capacity set.
36 Volume Retention Manager (VRM) Function Attribute Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[VRM],Attribute,,Normal end,,,Seq.=xxxxxx +{LDKC:CU:LDEV,Attribute,Result}=[{0x00:0x00:0x01,0x80,Normal end}, {0x00:0x00:0x02,0x82,Error(9205-8122),{0x00:0x00:0x03,0x81,Normal end}, {0x00:0x00:0x03,0x81,Normal end}],Num. of LDEVs=XXX [VRM] Volume Retention Manager function Attribute Attribute operation Normal end The operation has ended normally. Seq.
VTOC Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[VRM],VTOC,,Normal end,,,Seq.=xxxxxx +{LDKC:CU:LDEV,VTOC(Trk),Result}=[{0x00:0x00:0x01,xxxxx,Normal end}, {0x00:0x00:0x02,xxxxx,Error(9205-8122)},{ 0x00:0x00:0x03,xxxxx,Normal end}, {0x00:0x00:0x03,xxxxx,Normal end}],Num. of LDEVs=XXX [VRM] Volume Retention Manager function VTOC Volume Table of Contents operation Normal end The operation has ended normally. Seq.
37 Volume Shredder Function End Shredding Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Shredder],End Shredding,,Normal end,,, Seq.=xxxxx +{Times,Result}=[{1,Nomal},{2,Nomal},{3,Error}],Num. of Data=3 [Shredder] Volume Shredder function End Shredding End Shredding operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table.
0x00:0x1f:0xfb,0x00:0x1f:0xfc,0x00:0x1f:0xfd,0x00:0x1f:0xfe, -0x00:0x1f:0xff],Num. of LDEVs=21 [Shredder] Volume Shredder function Set Shredding Set Shredding operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 239 Detailed Info: Set Shredding Operation Item Description OwnerID The owner ID.
Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 240 Detailed Info: Suspend Shredding Operation Item Description Target OwnerID The owner ID. 0: Indicates HP XP Remote Web Console 0xXX: Owner ID is expressed in two digits of the hexadecimal format.
Volume Shredder Function
38 Volume Security (VSEC) Function Set Group Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[VSEC],Set Group,,Normal end,,,Seq.
The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 241 Detailed Info: Set Group Operation Item Description LDKC The group's LDKC number. Security Group The security group name. Host Group The host group name. LDEV Group The LDEV group name. Security The setting status of the security set to the security group.
Item Description CU The CU number registered in the LDEV group. LDEV The LDEV numbers registered in the LDEV group. Num. of LDEVs The number of LDEVs registered. Num. of LDEV Group The number of LDEV groups.
Volume Security (VSEC) Function
39 V Volume (VVOL) Function Add V-Vol (V) Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[VVOL],Add V-Vol(V),,Normal end,,,Seq.=xxxxx [VVOL] V Volume function Add V-Vol (V) Add V-Vol (V) operation for HP XP Snapshot Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Add V-Vol (X) Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[VVOL],Add V-Vol(X),,Normal end,,,Seq.
Connect/Release Pool Connect/Release Pool operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 242 Detailed Info: Connect/Release Pool Operation Item Description Command Indicates the operation executed to the HP XP Thin Provisioning Software (THP) volume.
Delete V-Vol (X) Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[VVOL],Delete V-Vol(X),,Normal end,,,Seq.=xxxxx [VVOL] V Volume function Delete V-Vol (X) Delete V-Vol (X) operation for HP XP Thin Provisioning Software Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Pool Change / Delete Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[VVOL],Pool Change/Delete,,Normal end,,,Seq.
Item Description 1: HP XP Snapshot, 2: HP XP Thin Provisioning Software Threshold(%) The threshold of the usage rate of the pool. The unit is percent (%). This index is output only when pool information is changed. Result The result of the operation. Normal end: Normal end, Error(xxxx-yyyy): Abnormal end, Not Execute: Not Executed xxxx: Part code, yyyy: Error code Num. of Data The number of the pool where the settings have been changed or the number of the pool that have been deleted.
Detailed information displays for this operation, as shown in the following table. Table 244 Detailed Info: Pool Restore Operation Item Description Pool ID The restored pool ID. Result The result of the operation: Normal end: Normal end, Error(xxxx-yyyy): Abnormal end, Not Execute: Not Executed xxxx: Part code, yyyy: Error code Num. of Pools The number of the restored pool. Pool SIM Comp Req Operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[VVOL], Pool SIM Comp Req,,Normal end,,,Seq.
[VVOL] V Volume function Set Pool Set Pool operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 246 Detailed Info: Set Pool Operation Item Description Pool ID The pool ID of the created pool. Pool Type The pool type. 1 is always output.
A Audit Log Information File Output by Function This appendix includes more detailed information about the audit log information file. Table 247 lists audit log information file output for operations that are common to all HP XP Remote Web Console functions. Table 248 lists audit log information file output for each program option in the HP XP Remote Web Console Main window.
Option Operation Menu Items for Launching Options LUN Security Extension Tab Output of Audit Log Information File Operation Function Name Operation Name Command Device: Enable –> Disable Set CommandDev (Note 1) Cmd Dev.Security: Disable –> Enable Set CommandDevSec (Note 1) Cmd Dev.
Option Operation Menu Items for Launching Options Output of Audit Log Information File Tab Operation Port (Note 4) Standard Mode Set Speed Mode (Note 1) High Speed Mode Set Speed Mode (Note 1) High Speed (2Port) Mode Set Speed Mode (Note 1) Fibre Addr.
Option Operation Menu Items for Launching Options Volume Manager Tab LUSE (Note 5) Output of Audit Log Information File Operation Function Name Authentication Mode: Set FCSP Port Switch bi-directional –> unidirectional (Note 1) (Note 2) Authentication Mode: Set FCSP Port Switch unidirectional –> bi-directional (Note 1) (Note 2) Authentication (Port): Enable –> Disable Set FCSP Port Switch Authentication (Port): Disable –> Enable Set FCSP Port Switch Make LUSE (Note 1) (Note 2) (Note 1) (
Option Operation Menu Items for Launching Options Tab Output of Audit Log Information File Operation Function Name Operation Name Delete Pool V-VOL Initialize Pool Pool Initialize (Note 1) Restore Pool Pool Restore (Note 1) Pool SIM Complete Request Pool SIM Copm Req (Note 1) New V-VOL Group Add V-Vol (V) (Note 1) Add V-Vol (X) (Note 1) Delete V-Vol (V) (Note 1) Delete V-VOL Group Delete V-Vol (X) (Note 1) Cache Residency Performance Control Base Monitor Cache Residency Monitoring Options
Option Operation Menu Items for Launching Options Tab Output of Audit Log Information File Operation Function Name Erase Migration History HP XP Continuous Access Pair Operations Paircreate Operation Name Del Migration Log Cnt Ac Paircreate (Note 1) Start Pair Pairsplit-S Pairsplit-S (Note 1) Pairsplit-r Pairsplit-r (Note 1) Pairresync Pairresync (Note 1) Start Pair RCU Operations Asynchronous Operations Other Operations 286 Change Pair Option Change Pair Option (Note 1) Change to Modi
Option Operation Output of Audit Log Information File Menu Items for Launching Options Tab Operation Function Name Operation Name HP XP Continuous Access Journal JNL Operation Edit JNL Volumes Cnt Ac-J Journal-Vol (Note 1) Disk Controller (DKC ) Operation Pair Operation HP XP Business Copy Change JNL Option Journal-Option (Note 1) Delete JNL Groups Journal-Vol (Note 1) Pairsplit-r Pairsplit-r (Note 1) Pairresync Pairresync (Note 1) Pairsplit-S Pairsplit-S (Note 1) Add Disk Controlle
Option Operation Menu Items for Launching Options Tab Output of Audit Log Information File Operation Function Name Operation Name Pairresync Pairresync (Note 1) Pairsplit-E Pairsplit-E (Note 1) Pairsplit-S Pairsplit-S NOTE: Function name is Snapshot when HP XP Snapshot pair is deleted.
Option Operation Menu Items for Launching Options Tab Asynchronous Operations Script Operations Output of Audit Log Information File Operation Function Name Operation Name Port Change (Target, Initiator, RCU Target) PORT Change Port Add Consistency Group TC Add CTG Consistency Group Option Change CTG Option Delete Consistency Group Delete CTG Async Option Change Async Option Run Script Operation Stop Other Operations Universal Replicator Mainframe JNL Operation Disk Controller (DKC )
Option Operation Menu Items for Launching Options Tab Pair Operation Function Name Operation Name Add Path Add Path (Note 1) (Note 2) Delete Path Delete Path (Note 1) (Note 2) Port Change (Target, Initiator, RCU Target) PORT Change Port Add Pair UR Add-Pair (Note 1) Suspend-Pair (Note 1) Resume Pair Resume-Pair (Note 1) Delete Pair Delete-Pair (Note 1) Change Pair Option Pair-Option (Note 1) Change System Option System-Option (Note 1) Clear SIM Clear-SIM (Note 1) EXCTG Operation Ad
Option Operation Output of Audit Log Information File Menu Items for Launching Options Tab Operation Function Name Operation Name Mainframe Connection Parallel Access Volumes Add CPAV Add Alias (Note 1) Delete Alias (Note 1) Delete Volume Security Set Group VSEC Set Group (Note 1) Volume Retention Mainframe Attribute VRM Attribute (Note 1) VTOC (Note 1) Volume Table of Contents Data Retention Data Retention Utility Attribute / S-VOL / Reserved/ Data Ret Attribute (Note 1) Mode Cle
Option Operation Menu Items for Launching Options Configuration File Loader Output of Audit Log Information File Tab Operation Function Name Operation Name Port Operation Change to Target / Change to External PORT Change Port Configuration File Loader Upload CFL LUNM Operation VRM Operation NOTE: The log information is not output for the format violation and inconsistency of configuration.
Note 3: When you perform two or more LUN Manager operations, the following conditions apply: • When you perform two or more operations on one target and select Apply, the log information is output as one entry. • When you apply two or more settings at one time, the log information is output according to the priority shown in Table 249. If the priority is the same, the log information is output in the order of the operations performed.
Note 4: When you set two or more port settings, the following conditions apply: • When you perform two or more operations for one target, the log information is output as one entry. • The log information is output in the order of the operations performed. • If you perform the following operations at the same time, the following happens: Change 1 –> Change 2: Log information is output for the Change 2 operation.
B SVP Operations Output to the Audit Log File Table 250 describes SVP operations and the operation name that is output to Audit Log File.
GUI operation SVP start button Output of Audit Log File Function Operation Function Name Operation Name Change Configuration Installation Install De-installation Uninstall System Option System Option Disk Unit (DKU) Emulation DKU Emulation System Tuning System Tuning LUN Configuration Set Fibre Address Set Fibre Topology Set Channel Speed Set CommandDev Set CommandDevSec Add LU Path Delete LU Path Set Speed Mode Set Host Mode Set Security Switch Add WWN Delete WWN Change WWN Add Host Group
GUI operation SVP start button Output of Audit Log File Function Operation Function Name Operation Name Force Reset Make LUSE Release LUSE DCR Configuration DCR Prestaging M/F DCR Open DCR CVS Configuration Install CV Volume to Space Make Vol./Vol.
GUI operation SVP start button Information 298 Output of Audit Log File Function Operation Function Name Setting Battery Life Setting Battery Life Set Battery Life Set Machine Install Date Set Machine Install Date Machine Install Date Log SIM Complete Information Operation Name SIM Complete Log Delete Delete Log SIM Reporting Option SIM Reporting Option Threshold Value Alter Threshold Value Online Read Margin Reset ORM Value SVP Operations Output to the Audit Log File
C Acronyms and Abbreviations API application program interface Auto LUN HP XP Auto LUN Software CFL Configuration File Loader CHA channel adapter CLPR Cache Logical Partition (part of HP XP Disk/Cache Partition) CPAV HP XP for Compatible Parallel Access Volumes Software CT consistency CTG consistency group CU control unit CV custom volume, customized volume (part of Virtual LVI/LUN) DASD direct-access storage device Data Ret Data Retention Utility DCR Dynamic Cache Residency (also c
LBA logical block address LCP local control port LDEV logical device LU logical unit LUN logical unit number LUNM LUN Manager LUSE LUN Expansion (also called LU Size Expansion) LVI logical volume image MCU main control unit MIB message information block MU mirror unit M-VOL main volume NVS nonvolatile storage P.P.
SFP small form-factor pluggable SHRED Volume Shredder SIM service information message SLPR Storage Logical Partition (part of HP XP Disk/Cache Partition) SM shared memory SMPL simplex SNMP simple network management protocol SSID subsystem ID S-VOL secondary volume (HP XP Continuous Access Software), source volume (ShadowImage for Mainframe) SVP service processor T-VOL target volume VDEV virtual device VLL Virtual LVI / Virtual LUN VMA volume management area VSEC Volume Security
Acronyms and Abbreviations
