HP StorageWorks XP24000/XP20000 Audit Log Reference Guide (AE131-96085, May 2011)

ManualsBrandsHP ManualsSoftwareHP Remote Web Console XP

HP StorageWorks

XP24000/XP20000 Audit Log User and

Reference Guide

Abstract

This document describes the system logs generated by XP Remote Web Console and SVP operations. Topics include how to

view and redirect log output. The intended audience is a storage administrator or authorized service provider with independent

knowledge of HP StorageWorks XP storage systems and XP software.

HP Part Number: AE131-96085

Published: May 2011

Edition: Twelfth

Summary of content (279 pages)

PAGE 1
HP StorageWorks XP24000/XP20000 Audit Log User and Reference Guide Abstract This document describes the system logs generated by XP Remote Web Console and SVP operations. Topics include how to view and redirect log output. The intended audience is a storage administrator or authorized service provider with independent knowledge of HP StorageWorks XP storage systems and XP software.
PAGE 2
© Copyright 2007, 2011 Hewlett-Packard Development Company, L.P. Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor's standard commercial license. The information contained herein is subject to change without notice.
PAGE 3
Contents 1 Introduction.............................................................................................12 Purpose of Audit Logs..............................................................................................................12 Download the Audit Log Information Files to the Remote Web Console Computer............................13 Download the Syslog Information File to the Remote Web Console Computer.................................
PAGE 4
Set CVAE Info Operation.........................................................................................................51 Set System Info Operation........................................................................................................51 Set Up HTTP Block Operation...................................................................................................52 Storage Device Add Operation............................................................................................
PAGE 5
Pairsplit-r Operation................................................................................................................78 Pairsplit-S Operation...............................................................................................................79 Pair-Option Operation.............................................................................................................80 R-Cmd. Dev. Operation.......................................................................................
PAGE 6
SIM Complete Operation.......................................................................................................107 SIM Reporting Option Operation............................................................................................108 Threshold Value Operation....................................................................................................109 22 Install Function.....................................................................................
PAGE 7
23 LDEV Function......................................................................................149 Volume-Blockade Operation...................................................................................................149 Volume-Format Operation......................................................................................................149 Volume-Format(H) Operation..................................................................................................
PAGE 8
Verify Operation...................................................................................................................177 Verify Stop Operation...........................................................................................................177 27 OND Function......................................................................................178 Release Cache/CLPR Operation.............................................................................................
PAGE 9
34 SI for Mainframe Function......................................................................200 Add Pair Operation..............................................................................................................200 Change Reserve Operation....................................................................................................200 CTG Operation....................................................................................................................
PAGE 10
System Disk Options Operation..............................................................................................231 Volume Initialize Operation....................................................................................................232 Volume to Space Operation...................................................................................................233 40 XP Auto LUN Software Function..............................................................234 Create Auto Plan Operation.
PAGE 11
46 Support and Other Resources.................................................................257 Related Documentation..........................................................................................................257 Conventions for Storage Capacity Values.................................................................................257 HP Technical Support............................................................................................................257 Subscription Service......
PAGE 12
1 Introduction This chapter introduces the audit logs created by the HP StorageWorks XP Remote Web Console computer or SVP (Service Processor) on the storage system. The SVP is a computer that is contained within the storage system. Users can access the audit logs that are output by the SVP, but the SVP is accessible only by HP personnel.
PAGE 13
Download the Audit Log Information Files to the Remote Web Console Computer Only the storage administrator can download the audit log file, and the Audit Log Administrator Role needs to be set to Modify or View. See the HP StorageWorks XP24000/XP20000 Remote Web Console User Guide for details for the Remote Web Console main window. To download the audit log information file using the Audit button: 1. Log on as a storage administrator and open the Remote Web Console main window. 2. 3.
PAGE 14
2. 3. 4. 5. Log on as a storage administrator and open the Remote Web Console main window. Change to Modify mode. Click Go-Security-Audit log Transfer in the menu bar of the Remote Web Console main window. The Audit Log Transfer window displays. (see Figure 1 (page 15)). Select one of the following: • • 6. 7. 8. If using a primary FTP server: ◦ Select Enable in Output to Primary Server. ◦ Enter the IP Address in the Primary Server Setting. Do not enter the periods.
PAGE 15
Figure 1 Audit Log Transfer Window Transferring the Audit Log Files to Syslog Servers Audit logs of the storage system can be transferred to a syslog server, the audit log in the same format with the audit log transferred to the syslog server can be downloaded as syslog information file. The protocol used to transfer audit logs to a syslog server is UDP (User Datagram Protocol). Consider the characteristics of UDP in the network setting when audit logs are transferred to the syslog server.
PAGE 16
5. Select one of the following: • If using a primary syslog server: ◦ • 7. 8. 9. 16 – Enter the IP Address in Primary Server Setting. Do not enter the periods. – Enter the Port Number in Primary Server Setting. You can enter a number from 1 to 65,535. If using a secondary syslog server: ◦ 6. Select Enable in Output to Primary Server. Select Enable in Output to Secondary Server. – Enter the IP Address in Secondary Server Setting. Do not enter the periods.
PAGE 17
10. Confirm that the syslog server is receiving the log of syslog server setting when the setting operation is completed. AuditLog is the function name of the log and Set Syslog Server is the operation name (see “Set Syslog Server Operation” (page 45)). If the log is not received by the syslog server, verify that the IP address and the port number set matches with the IP address and the port number of the syslog server. If the IP address and the port number matches, check the syslog server setting.
PAGE 18
4. 5. 6. Select one of the following for Audit Log Buffer: • Enable to temporarily store audit logs in a system disk before storing the logs in the SVP. • Disable to store audit logs directly in the SVP. Click Apply. A confirmation message appears. Click OK. Figure 3 Audit Log Setting Window Audit Log File Description The audit log file includes the components listed in Table 1 (page 18).
PAGE 19
Table 1 Audit Log File Components (continued) Component Audit Log Information File Syslog Information File Linefeed Codes CR + LF (Some text editors cannot display these codes correctly) LF File Output Contains login and logout information as well as basic and detailed information about settings made for each option. Basic information consists of information common to each audit log. Detailed information consists of information about the operations of each executed option.
PAGE 20
2 Audit Log File Format This chapter describes the two types of audit log files and the items included in the files. • “Audit Log Information File” (page 20) • “Syslog Information File” (page 22) Audit Log Information File The audit log information file consists of both basic and detailed information about user logins, logouts and disk array configuration change operations. The detailed information includes an index representing each item and its setting's values.
PAGE 21
Table 2 Items in Audit Log Information File (continued) No. Item Explanation 6 Function name2 The abbreviation indicating the function or option which has been used to perform the setting operation is output. See “Audit Log Information File Functions, Operations, and Programs” (page 27) for the relationship between the abbreviation output and the actual function. This information is not output when commands are received from the host.
PAGE 22
1 2 3 A date and a time being set on SVP are output as log data. If a failure, such as a SVP failure and a LAN failure, occurs in the storage system, the date and time may be output with the date and time of January 01, 1970. Function names are used as section titles in “Sample Audit Logs of Remote Web Console PC and SVP Operations” (page 38). Operation or event names are used as subsection titles in “Sample Audit Logs of Remote Web Console PC and SVP Operations” (page 38).
PAGE 23
Figure 5 Syslog Information File Table 4 Items in the Syslog File No. Item Description 1 Priority The priority according to the following formula, enclosed by brackets (< >): Priority = 8 x Facility + Severity Facility is 1 (fixed). The Severity depends on the type of log information: 4: Error or Warning. Error means the operation has ended abnormally. Warning means the operation has partly ended abnormally or was canceled during the operation. 6: Informational. The operation has ended normally.
PAGE 24
Table 4 Items in the Syslog File (continued) No. Item Description 7 Message identification information The serial number of the syslog header information. Date, time#21 The date, time and the time difference between UTC (Coordinated Universal Time) in the format of YYYY-MM-DD-Thh:mm:ss.s hh:mm (YYYY: year, MM: month, DD: day, hh: hour, mm: minute, ss.s: second, hh: hours of the time difference and mm: minute of the time difference) 8 9 Message ID. Not displayed because it is not used.
PAGE 25
Table 4 Items in the Syslog File (continued) No. Item Description 21 Detailed information Identification information for the host sending the request is displayed. For more information, see “Audit Log Information for the Commands Sent from the Host” (page 252). This information is output when commands are received from the host. However, the information is not output when FC-SP are received. 22 Port sending the request. Not displayed because it is not used. 23 Host to which the request is sent.
PAGE 26
Table 4 Items in the Syslog File (continued) No. Item Description The same information contained in the basic information for the audit log information file is also displayed. For more information, see each operation name in “Audit Log Information File” (page 20). 1 A date and a time being set on SVP are output as log data. If a failure, such as a SVP failure and a LAN failure, occurs in the storage system, the date and time may be output with the date and time of January 01, 1970.
PAGE 27
3 Information Output in the Audit Log Information File This chapter shows the relationship between the audit log functions, operations, and option names.
PAGE 28
Table 6 Audit Log Information File Functions, Operations, and Programs (continued) Function Name Operation and Page Option Name “Storage Device Add Operation” (page 52) Changing Information on the Storage Entry window “Storage Device Del Operation” (page 53) “Storage Device Edit Operation” (page 54) Cache “DCR Prestaging Operation” (page 60) Cache Residency Manager Cache Residency Manager for Mainframe CFL “Delete Cache Residency Manager for z/OS (M/F DCR) Operation” (page 60) Cache Residency Mana
PAGE 29
Table 6 Audit Log Information File Functions, Operations, and Programs (continued) Function Name Operation and Page Option Name “Backup Config Operation” (page 113) “Change Host Group Operation” (page 114) “Change WWN Operation” (page 114) “Cache Residency Manager (DCR) Prestaging Operation” (page 115) “Define Config.
PAGE 30
Table 6 Audit Log Information File Functions, Operations, and Programs (continued) Function Name Operation and Page Option Name “Set IP Address Operation” (page 137) “Set Security Switch Operation” (page 138) “Set Speed Mode Operation” (page 139) “Set Subsystem Time Operation” (page 139) “System Option Operation” (page 140) “System Tuning Operation” (page 142) “Uninstall Operation” (page 143) “Update Config Operation” (page 147) “Volume to Space Operation” (page 147) LDEV “Volume-Blockade Operation” (pa
PAGE 31
Table 6 Audit Log Information File Functions, Operations, and Programs (continued) Function Name Operation and Page Option Name “Set Fibre-Channel Security Protocol (FCSP) Host Operation” (page 158) “Set Fibre-Channel Security Protocol (FCSP) Port Info Operation” (page 158) “Set Fibre-Channel Security Protocol (FCSP) Port Switch Operation” (page 159) “Set Fibre-Channel Security Protocol (FCSP) Target Operation” (page 160) “Set Fibre Address Operation” (page 160) “Set Fibre Topology Operation” (page 162)
PAGE 32
Table 6 Audit Log Information File Functions, Operations, and Programs (continued) Function Name Operation and Page Option Name PORT “Change Port Operation” (page 188) Changes port attribute operation from XP Continuous Access Software, Hitachi TrueCopy™ for Mainframe, XP Continuous Access Journal Software, Hitachi Universal Replicator™ for Mainframe, or XP External Storage Software PP KEY “PP Apply Operation” (page 189) License Key “PP Available Install Operation” (page 189) “PP Disable chk Operat
PAGE 33
Table 6 Audit Log Information File Functions, Operations, and Programs (continued) Function Name Operation and Page Option Name Perf Ctrl “Change XP Performance Control Group (PerfCtrlGrp) Operation” (page 179) XP Performance Control “Clear PPC Info Operation” (page 179) “Default Set Operation” (page 179) “XP Performance Control Group (PerfCtrlGrp) Delete/Change (Del/Chg) Operation” (page 180) “Set All Priority (Prio) Port Operation” (page 181) “Set All Priority (Prio) WWN Operation” (page 181) “Set C
PAGE 34
Table 6 Audit Log Information File Functions, Operations, and Programs (continued) Function Name Operation and Page Option Name “Resume Pair Operation” (page 215) “Script Operation” (page 216) “Suspend Pair Operation” (page 216) Cnt Ac-J “Journal-Option Operation” (page 74) XP Continuous Access Journal “Journal-Vol Operation (Add Parameter)” (page 75) “Journal-Vol Operation (Group-Delete Parameter)” (page 76) “Paircreate Operation” (page 76) “Pairresync Operation” (page 77) “Pairsplit-r Operation” (pa
PAGE 35
Table 6 Audit Log Information File Functions, Operations, and Programs (continued) Function Name Operation and Page Option Name VLL “Install CV Operation” (page 229) Virtual LVI/Virtual LUN (VLL) “Make Volume Operation” (page 230) “Set SSID Operation” (page 231) “System Disk Options Operation” (page 231) “Volume Initialize Operation” (page 232) “Volume to Space Operation” (page 233) Auto LUN XP Auto LUN1 “Create Auto Plan Operation” (page 234) “Del Auto Plan Log Operation” (page 234) “Delete Auto Pl
PAGE 36
Receiving Command from the Host Table 7 (page 36) shows the interface name and the operation name output to the Audit Log Information File in receiving command from the host. For details about the interface name and the operation name, see “Audit Log Information for the Commands Sent from the Host” (page 252).
PAGE 37
Audit Log Reproduced Output Table 10 (page 37) shows the operation name, event name, and triggering events that are output when the audit log file is reproduced. The create file event name will be automatically output only once. A sample output of this file is described in “Audit Log Buffer” (page 43). Table 10 Audit Log File Output Function Name Event Name Output Trigger AuditLog Create File Output when abnormal files in the Audit log are reproduced automatically.
PAGE 38
4 Sample Audit Logs of Remote Web Console PC and SVP Operations This chapter includes a sample audit log for each function and operation that can be performed with the Remote Web Console. The individual items in each sample log are described, starting with function name. This includes function name, operation name, parameter, operation result, and sequence number, as shown in Figure 6 (page 38).
PAGE 39
5 Account Function Set User Account Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx,00:00,[Account],Set User Account,,Normal end,,,Seq=xxxxx +Operation=Change +{UserID,Authority,SLPRNo,WritePermission,ReadPermission,AccountFlag}= -[{use001,Administrator,65535,FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF FFFFFFFFFF FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF,-,Enable}, -{use002,User,1,-,-,Disable}]Num.
PAGE 40
00000000000000000000000000000(snip)000100000001(1st bit) after it is converted to binary. The 1st and the 9th bit positions are on. Table 13 (page 40) shows that these bit positions indicate write permissions for information and LUN Manager function. Read permissions are indicated in the same manner.
PAGE 41
Table 13 Bit Position and the Relationship Between Function Name and R/W Permission (continued) Bit Position Function Name Permission of Remarks in Binary Storage Partition (descending order) Administrator1 3, 2 41 TrueCopy - 40-36 Not used - 35 Performance Port Control - 3, 2 34 Volume Migration - 3, 2, 4 33 Performance Monitor Yes 3, 2 32-26 Not used - 25 Cache Residency Manager Yes 24-21 Not used - 20 V-VOL - 3, 2 19 Pool - 3,2 18 VLL Yes 3,2 17 LUSE Yes
PAGE 42
Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 14 (page 42). Table 14 Set Login Message Operation 42 Item Description LoginMessageSentence Indicates the sentence of login Message displayed on the login window of Remote Web Console.
PAGE 43
6 Audit Log Function Audit Log Buffer user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[AuditLog],Audit Log buffer,,Normal end,,, Seq.=xxxxx +{Option,Set,Result}=[{Audit Log buffer,Enable,Normal}],Num. of Modes=1 [Audit Log] Audit Log function Audit Log buffer Audit Log buffer operation Normal end The operation has ended normally. Seq. =xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 15 (page 43).
PAGE 44
DKCAuditLog was lost DKCAuditLog was lost event Error The operation has ended abnormally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Over MaxLine Event 14> Jan 4 06:25:18 SVP Storage: CELFSS,1.1,250001,,2006-01-04T06:25:18.3Z,Storage,SVP, AnomalyEvent,Success,,R600:65307,,Japan-Tokyo,,,,,,,,,,,,,[AuditLog],Over MaxLine,, Normal end This information displays in the syslog information file only. No parameters display for this event.
PAGE 45
Table 16 Set FTP Server Operation Item Description ServerType The server type of the FTP (File Transfer Protocol) server to be set. If the setting is not changed, a hyphen (-) is displayed. Primary: Primary FTP server. Secondary: Secondary FTP server. IPAddrVer The version number of the internet protocol. If the setting is not changed, a hyphen (-) is displayed. IPv6: Internet Protocol Version 6. IPv4: Internet Protocol Version 4 OutFlg Whether to transfer the audit log information file (audit.
PAGE 46
Table 18 Set Syslog Server Operation Item Description DetailFlg Indicates whether to output detailed information to the syslog server. Enable: Output detailed information. Disable: Do not output detailed information. LocationInfo The location identification information for the storage system. Not output when setting is not changed. ServerType The syslog server to which information is output. Not output when setting is not changed. Primary: Primary syslog server. Secondary: Secondary syslog server.
PAGE 47
7 BASE Function Certificate Update Operation user-name.xx,YYYY/MM/DD:HH:MM:SS.xxx,00:00,[BASE],Certificate Update,,Normal end,,, Seq.=xxxx +{File Name,Result}=[{server.crt,Normal end},{server.key,Error(XXX-XXXX)}] [BASE] BASE function Certificate Update Certificate Update operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 20 (page 47).
PAGE 48
Table 21 Control Panel Backup Operation Item Description File Name Name of the backup file Result Result of the backup operation Normal end: normal end, Error (xxxx-yyyy): Abnormal end, -: not selected xxxx: part code, yyyy: error code Control Panel Restore Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[BASE],Control Panel Restore,,Normal end,,, Seq.
PAGE 49
Table 23 Delete CVAE Info Operation Item Description ID ID (unique ID row by row) of the version information to be deleted Num of IDs The number of IDs Environment Setting Operation user-name.xx,YYYY/MM/DD:HH:MM:SS.xxx,00:00,[BASE], Environment Setting,,Normal end,,, Seq.
PAGE 50
Detailed information displays for this operation, as shown in Table 25 (page 50). Table 25 Login Operation Item Description IPAddr The IP address of the connected client (Ipv4 or Ipv6). IPv4 address may be indicated in a mixed environment of IPv4 and IPv6. Logout Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[BASE],Logout,,Normal end,,,Seq.=xxxxx [BASE] BASE function Logout Logout operation Normal end The operation has ended normally. Seq.
PAGE 51
Table 27 Release HTTP Block Operation Item Description HTTP Block Status of the HTTP Block. - : disabled, Blocked : enabled Result Result of the HTTP Block setting Normal end: normal end, Error (xxxx-yyyy): Abnormal end xxxx: part code, yyyy: error code Set CVAE Info Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx,00:00,[BASE],Set CVAE Info,,Normal end,,,Seq.=xxxxxx +{ID,ProductName,VersionInfo,IPAddress,RegistryDate,LastAccessDate,MemoRandom}= -{1,DevMgr,6.0.0.-00,10.213.38.
PAGE 52
Set System Info Set System Information operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 29 (page 52). Table 29 Set System Info Operation Item Description Name Nickname of the device Contact Name of the system administrator. Location Installation location of the device. Num of SystemInfo Number of system information.
PAGE 53
Storage Device Add operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 31 (page 53).
PAGE 54
Storage Device Edit Operation user-name.xx,YYYY/MM/DD:HH:MM:SS.xxx,00:00,[BASE], Storage Device Edit,,Normal end,,, Seq.=xxxx +{No,NickName,ProductName,SerialNo,HostName or IPAddress,Location,HTTP Block}= {1,nickname,H20000,12345,127.0.0.1,Blocked} [BASE] BASE function Storage Device Edit Storage Device Edit operation Normal end The operation has ended normally. Seq.
PAGE 55
8 XP Business Copy Software Function Change Reserve Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx,00:00,[BC],Change Reserve,,Normal end,,,Seq.=xxxxx +Attribute=Set ++{VOL(LDKC:CU:LDEV),Result}=[{0xZZ:0xXX:0xYY,Normal end},{0xZZ:0xXX:0xYY, Error(xxxx-yyyy)}],Num. of Vols=2 [BC] HP XP Business Copy Software function Change Reserve Change Reserve operation Normal end The operation has ended normally. Seq.
PAGE 56
Option Option operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 35 (page 56). Table 35 Option Operation Item Description Swap & Freeze Indicates whether the Swap & Freeze option is enabled or disabled. Enable: Option is enabled, Disable: Option is disabled.
PAGE 57
Pairresync Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[BC],Pairresync,,Normal end,,,Seq.=xxxxx +Copy pace=Faster,Resync Type=Normal Copy ++{P-VOL(LDKC:CU:LDEV),S-VOL(LDKC:CU:LDEV),Result}=[{0xXX:0xAA:0xBB,0xYY:0xCC:0xDD, Normal end},{0xXX:0xAA:0xBB,0xYY:0xCC:0xDD,Error(xxxx-yyyy)}],Num. of Pairs=2 [BC] HP XP Business Copy Software function Pairresync Pairresync operation Normal end The operation has ended normally. Seq.
PAGE 58
Table 38 Pairsplit Operation Item Description Copy Pace The set copy speed Faster: High speed Medium: medium speed Slower: Low speed Split Type The split type Quick Split: Pair split by background copy Steady Split: Pair split by update copy P-VOL(LDKC:CU:LDEV) The LDKC, CU, and LDEV numbers of the primary volume in the split pair S-VOL(LDKC:CU:LDEV) The LDKC, CU, and LDEV numbers of the secondary volume in the split pair MU The MU number of the split pair Result The result of operation Normal
PAGE 59
user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx,00:00,[BC],Pairsplit-S,,Normal end,,,Seq.=xxxxx +{P-VOL(LDKC:CU:LDEV),S-VOL(LDKC:CU:LDEV),Result}=[{0xAA:0xBB:0xCC,0xDD:0xEE:0xFF,Normal end}, {0xAA:0xBB:0xCC,0xDD:0xEE:0xFF,Error(xxxx-yyyy)}],Num. of Pairs=2 Example 2 (HP XP Snapshot is used) user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx,00:00,[BC],Pairsplit-S,,Normal end,,,Seq.
PAGE 60
9 Cache Function DCR Prestaging Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Cache],DCR Prestaging,, Normal end,,,Seq.=xxxxx [Cache] Cache function DCR Prestaging DCR Prestaging operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Delete Cache Residency Manager for z/OS (M/F DCR) Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx,00:00,[Cache],Delete M/F DCR,,Normal end,,,Seq.
PAGE 61
Delete Open DCR operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 42 (page 61). Table 42 Delete Open DCR Operation Item Description LDKC:CU:LDEV The LDKC, CU, and LDEV numbers of the logical volume (for an open system) where the setting information for Cache Residency cache is canceled.
PAGE 62
Table 43 Set M/F DCR Operation (continued) Item Description End CC-HH The ending cylinder number (CC) and the ending head number (HH) of the data resident in Cache Residency cache. Num. of LDEVs The number of the logical volume (for a mainframe system) where the setting information for Cache Residency cache is added or changed. Set Open Cache Residency Manager (DCR) Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Cache],Set Open DCR,,Normal end,,,Seq.
PAGE 63
10 CFL Function LUNM Operation The Configuration File Loader log appears in the log file line. It is located between where the line contains “Start” and the line contains “End.” user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[CFL],LUNM Operation,Start,Normal end,,,Seq.=xxxxx [CFL] Configuration File Loader function LUNM Operation LUN Manager operation Start Start is the selected parameter. This operation uses the following parameters, as shown in Table 45 (page 63).
PAGE 64
11 CFL Extension Function CflSet Start Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx,00:00,[CFL Extension],CflSet Start,,Normal end,,,Seq=xxxxx +{Input,Output}={C:\Set_IN.spd,C:\Set_OUT.spd} [CFL Extension] CFL Extension function CflSet Start Operation CflSet Start operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 47 (page 64).
PAGE 65
12 XP Continuous Access Software Function Add CTG Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Cnt Ac],Add CTG,,Normal end,,,Seq.=xxxxx +{LDKC,CTG,Path,Offloading(s),Inflow Control,Copy Pending(min.),RCU Ready(min.)}= {0x00,0x00,Fibre,090,Enable,05,05} [Cnt Ac] HP XP Continuous Access Software function Add CTG Add Consistency Group operation Normal end The operation has ended normally. Seq.
PAGE 66
Table 49 Change Async Option Item Description CLPR The CLPR number. Rate (%) The value set to the pending update data rate. Delay Start (%) The value set to the I/O Delay Start value (the threshold that the inflow control of asynchronous copy starts). Delay Increase (%) The value set to the I/O Delay Increase value (the threshold that the inflow control of asynchronous copy increases). Change CTG Option Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.
PAGE 67
Change Option Change Option operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 51 (page 67). Table 51 Change Option Operation Item Description Parallel Initial Copy The maximum number of initial copy operations set. (1 to 512) Path Blockade Watch(s) The path blockade watch period set. The unit is second.
PAGE 68
Detailed Information Detailed information displays for this operation, as shown in Table 52 (page 68). Table 52 Change Pair Option Operation Item Description P-VOL (Port-G-ID-LUN) The port number, host group number and LUN of the primary volume where the pair option is changed sequentially. Fence Level The changed fence level (the condition that MCU rejects Write to the primary volume).
PAGE 69
Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 54 (page 69). Table 54 Function Switch Operation Item Description Switch Each bit position (on/off) of the function switch information assigned by 64 bits. The beginning of the string is bit 0 and the ending of it is bit 63. "0" indicates the bit is off, and "1" indicates the bit is on.
PAGE 70
Table 55 Paircreate Operation (continued) Item Description Initial Copy The initial copy mode set Entire: Copy all, None: Do not copy Fence Level The fence level set (the condition that MCU rejects the write operation to the primary volume) Never: No condition, Data: S-VOL data, Status: S-VOL status Copy Pace The initial copy speed set (the number of tracks you can copy at one time) Priority The priority of the set initial copy operation (scheduling order) Diff The unit of the differential manage
PAGE 71
Table 56 Pairresync Operation (continued) Item Description Fence Level The fence level set (the condition that MCU rejects Write to the primary volume). Never: No condition, Data: S-VOL data, Status: S-VOL status Copy Pace The initial copy speed set (the number of tracks you can copy at a time). Priority The priority of restoring operation set (scheduling order). Range The resume range set (the range to restore the asynchronous pair).
PAGE 72
Table 57 Pairsplit-r Operation Item Description P-VOL (Port-G-ID-LUN) The port number, host group number, and LUN of the primary volume in the split pair sequentially S-VOL (Port-G-ID-LUN) The port number, host group number , and LUN of the secondary volume in the split pair sequentially Type The volume type of the volume on the primary site P-VOL: Primary volume, S-VOL: Secondary volume S-VOL Write Indicates whether writing to the secondary volume is enabled Enable: Writing is enabled Disable: Wri
PAGE 73
Table 58 Pairsplit-S Operation Item Description P-VOL (Port-G-ID-LUN) The port number, host group number, and LUN of the primary volume in the deleted pair sequentially S-VOL (Port-G-ID-LUN) The port number, host group number, and LUN of the secondary volume in the deleted pair sequentially Type The volume type of the volume on the primary site P-VOL: Primary volume, S-VOL: Secondary volume Force The setting for forced pair deletion Yes: Pair is deleted even when MCU cannot communicate with RCU No:
PAGE 74
13 XP Continuous Access Journal Software Function Journal-Option Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Cnt Ac-J],Journal-Option,,Normal end,,,Seq.=xxxxx +{LDKC,JNLG,MetaData Ratio,Extent,Data Overflow Watch(s),Inflow Control,Copy Pace, Path Watch Time,Forward Path Watch Time,Use of Cache,Speed of Line(Mbps), Delta resync Failure,Result}={0x00,0x00,32,32,20,No,150,30,Yes,Not Use,256,Entire, Normal end}, -{0x00,0x01,32,32,20,No,150,30,No,Use,256,Entire,Normal end},Num.
PAGE 75
Table 59 Journal-Option Operation (continued) Item Description Result The result of the operation. Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of JNL Grps The number of journal groups. Journal-Vol Operation (Add Parameter) user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx,00:00, [Cnt Ac-J],Journal-Vol,Add,,Normal end,,,Seq.
PAGE 76
Journal-Vol Operation (Group-Delete Parameter) user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx,00:00,[Cnt Ac-J],Journal-Vol,Group-Delete,,Normal end,Seq.=xxxxxx +{LDKC,JNLG,Result}=[{0x00,0x80,Normal end},{0x00,0x81,Normal end},{0x00,0x82, Normal end}], Num. of JNL Grps=3 [Cnt Ac-J] HP XP Continuous Access Journal Software function Journal-Vol Journal-Vol operation Group-Delete Group-Delete is selected as the parameter. The journal group is deleted. Normal end The operation has ended normally. Seq.
PAGE 77
Table 63 Paircreate Operation Item Description P-VOL (Port-G-ID-LUN) The port number, host group number, and LUN of the primary data volume S-VOL (Port-G-ID-LUN) The port number, host group number, and LUN of the secondary data volume MirrorID The mirror ID S/N The serial number of the logical device (storage system) CTRLID The controller ID Priority The priority of copy CTG The consistency group ID Initial Copy Indicates whether initial copy or paircreate operation for Delta resync is exec
PAGE 78
Table 64 Pairresync Operation Item Description P-VOL (Port-G-ID-LUN) The port number, host group number, and LUN of the primary data volume S-VOL (Port-G-ID-LUN) The port number, host group number, and LUN of the secondary data volume MirrorID The mirror ID S/N The serial number of the logical device (storage system) CTRLID The controller ID Priority The priority of copy CTG The consistency group ID Range The range to restore the pair Group: Group range.
PAGE 79
Table 65 Pairsplit-r Operation Item Description P-VOL (Port-G-ID-LUN) The port number, host group number, and LUN of the primary data volume S-VOL (Port-G-ID-LUN) The port number, host group number, and LUN of the secondary data volume MirrorID The mirror ID S/N The serial number of the logical device (storage system) CTRLID The controller ID Type Indicates whether the split data volume is a primary or secondary data volume P-VOL: Primary, S-VOL: Secondary S-VOL Write Indicates whether writin
PAGE 80
Table 66 Pairsplit-S Operation (continued) Item Description CTRLID The controller ID. Type Indicates whether the deleted data volume is a primary or secondary data volume. P-VOL: Primary, S-VOL: Secondary Range The delete range. LU: LU range, Group: Group range Delete Mode The delete mode. Normal: Normal mode, Force: Force mode Result The result of operation. Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code,yyyyy: Error code Num. of Pairs The number of pairs.
PAGE 81
Table 67 Pair-Option Operation (continued) Item Description Result The result of operation. Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Pairs The number of changed pairs. R-Cmd. Dev. Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[UR],R-Cmd.Dev.,Assign,Normal end,,,Seq.=xxxxx +{LDKC,JNLG,MirrorID,Cmd.Dev.(LDKC:CU:LDEV),Result}= [{0x00,0x01,0x01,0x00:0x12:0x34,Normal end},{0x00,0x10,0x02,0x00:0x56:0x78,Normal end}], Num.
PAGE 82
Table 69 R-Cmd.Dev. Operation (continued) Item Description Result The result of operation Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Mirrors The number of mirrors changed System-Option Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Cnt Ac-J],System-Option,,Normal end,,,Seq.
PAGE 83
14 XP for CPAV Software Function Add Alias Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[CPAV],Add Alias,,Normal end,,,Seq.=xxxxx +LDKC=0x00,CU=0x00 ++{Alias LDEV,Base LDEV}=[{0xFD,0x00},{0xFE,0x00},{0xFF,0x01}],Num. of Alias LDEVs=3 +LDKC=0x00,CU=0x01 ++{Alias LDEV,Base LDEV}=[{0xFF,0x00}],Num. of Alias LDEVs=1 +Num. of Alias LDEVs=4 [CPAV] CPAV function Add Alias Add Alias operation Normal end The operation has ended normally. Seq.
PAGE 84
Table 72 Delete Alias Operation Item Description LDKC Indicates LDKC number containing the alias device and the base device. CU Indicates CU number containing the alias device and the base device. Alias LDEV The alias device number allocated to the CU number indicated in CU of the index. Base LDEV The base device number allocated to the CU number indicated in CU of the index. Num. of Alias LDEVs The number of alias devices allocated to the CU number indicated in CU of the index. Num.
PAGE 85
15 Data Retention Utility Function Attribute Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Data Ret],Attribute,,Normal end,,,Seq.=xxxxx +{LDKC:CU:LDEV,Attribute,RT,Result}=[{0x00:0x00:0x01,0x80,100,Normal end}, {0x00:0x00:0x02,0x82,Unlimited,Error(9605-8122)},{0x00:0x00:0x03,0x81,200, Normal end}, {0x00:0x00:0x03,0x81,xxxx,Normal end}],Num. of LDEVs=XXX [Data Ret] Data Retention Utility function Attribute Attribute operation Normal end The operation has ended normally. Seq.
PAGE 86
Data Retention Utility function Expiration-Lock Expiration-Lock operation SLPR#xx:Enable SLPR#xx: Enable is selected as the parameter. The operation uses the following parameters, as shown in Table 74 (page 86). Table 74 Parameters for Expiration-Lock Operation Parameter Description SLPR#xx:Enable The expiration-lock setting is enabled for SLPR number xx. SLPR#xx:Disable The expiration-lock setting is disabled for SLPR number xx.
PAGE 87
16 XP Disk/Cache Partition Function Set Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[DCPart],Set,,Normal end,,,Seq.=xxxxxx +Delete SLPR=[xx,xx],Num. of SLPRs=xx +Delete CLPR=[xx,xx],Num. of CLPRs=xx +SLPR=xx:xxxxxxxxxxxxxx,Operation=xxxxx ++Port=[CLx-x,CLx-x],Num. of Ports=xx ++CU=[0xXX:0xXX,0xXX:0xXX] ,Num. of CUs=xx ++SSID=[0xXXXX,0xXXXX],Num. of SSIDs=xx ++CLPR=xx:xxxxxxxxxxxxxx,Cache(MB)=xxxxx,Cache Residency(MB)=xxxx, Num. of Cache Residency Areas=xxxx +++PG=[xx-xx,xx-xx],Num.
PAGE 88
Table 75 Set Operation (continued) Item Description PG The parity group number assigned to CLPR. When the external volume is present in the parity group, the first letter of the parity group number is E. 88 Num. of PGs The number of parity groups assigned to CLPR. Num. of CLPRs The number of CLPRs by set SLPR. Num. of SLPRs The number of SLPRs set.
PAGE 89
17 Email Info Function MailAddress Write Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Email Info],MailAddress Write,, Normal end,,,Seq.=xxxxx +{MailServerSetting,MailServer}={HostName,smtp.test.co.jp} +{SMTP AUTH,Account}={Enable,Account} +{FromAddress,ReturnAddress}={TransAddr@co.jp,ReplyAddr@co.jp} +UsedCount=32 ++{ToAddressList,Attribute}=[{usr1@co.jp,TO},{usr2@co.jp,TO},{usr3@co.jp,TO},{usr4@co.jp,CC}, : {usr25@co.jp,CC},{usr26@co.jp,BCC},{usr27@co.jp,BCC},{-,-},{-,-},{usr31@co.jp,BCC}], Num.
PAGE 90
Email Info function Valid Flag Update Valid Flag Update operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 77 (page 90). Table 77 Valid Flag Update Operation 90 Item Description MailNoticeSetting Indicates whether the mail notice is enabled or disabled. Disable or Enable will appear.
PAGE 91
18 XP External Storage Access Manager function Add Quorum Disk ID Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[ESAM],Add Quorum Disk ID,,Normal end,,, Seq.=xxxxx +{Quorum Disk ID,Paired S/N,Controller ID,Quorum Disk(LDKC:CU:LDEV)}= {0x01,60011,5,0x01:0x02:0x03} [ESAM] XP External Storage Access Manager function Add Quorum Disk ID Add Quorum Disk ID operation Normal end The operation has ended normally. Seq.
PAGE 92
Table 79 Del Quorum Disk ID Operation (continued) Item Description Controller ID The controller ID of the paired storage system Quorum Disk (LDKC:CU:LDEV) The LDKC, CU, and LDEV numbers of the deleted quorum disk Paircreate Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[ESAM],Paircreate,,Normal end,,,Seq.
PAGE 93
Table 80 Paircreate Operation (continued) Item Description Quorum Disk ID The quorum disk ID used by the pair. Result The result of operation Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Pairs The number of created pairs Pairresync Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[ESAM],Pairresync,,Normal end,,,Seq.
PAGE 94
-{1A-0x00-0x000,1B-0x00-0x000,P-VOL,Disable,S-VOL,Normal End}, {1A-0x00-0x001,1B-0x00-0x001,P-VOL,Disable,S-VOL,Normal End}, (snip) -(snip), Num.of Pairs=xx [ESAM] XP External Storage Access Manager function Pairsplit-r Pairsplit-r operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 82 (page 94).
PAGE 95
Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 83 (page 95).
PAGE 96
19 XP External Storage Software Function AddVolume(FIBRE) Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Ext Stor],AddVolume(FIBRE),,),,Normal end,,,Seq.
PAGE 97
Table 84 AddVolume(FIBRE) Operation (continued) Item Description Inflow The inflow control set to the cache of the mapped external volume Enable: Enabled, Disable: Disabled Result The result of the operation Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Port The port name of the external port of the local storage system WWN The WWN of the Target port of the external storage system LUN The LUN of the external volume Num.
PAGE 98
Table 85 BlockPaths(FIBRE) Operation (continued) Item Description Result The result of operation. Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Paths The number of mapping paths that has been disconnected. Change-CacheMode Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Ext Stor],Change-CacheMode,Enable,Normal end,,,Seq.=xxxxx +{Group,Result}=[{E1-1,Normal End},{E1-2,Error(605-3003)},{E1-3,Normal End}, {E1-4,Normal End}],Num.
PAGE 99
HP XP External Storage Software function ChangePaths(FIBRE) ChangePaths(FIBRE) operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 88 (page 99).
PAGE 100
Table 89 CheckPaths(FIBRE) Operation Item Description Port The port name of the external port of the local storage system. WWN The WWN of the Target port of the external storage system. Result The result of operation. Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Paths The number of mapping paths that path status has been checked.
PAGE 101
Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 91 (page 101). Table 91 DeleteVolume(FIBRE) Operation Item Description ExGroup The number of the external volume group and the reference number assigned to the external volume of the external volume that the mapping has been released.
PAGE 102
Table 92 Disconnect-Volume Operation Item Description Group The group number of the disconnected external volume. Result The result of operation. Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Groups The number of external volume groups that contain the disconnected external volume. DividePathGroup Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx,00:00,[UVM],DividePathGroup,,Normal end,,,Seq.
PAGE 103
HP XP External Storage Software function Inflow-Control Inflow-Control operation Enable Enable is selected as the parameter. The operation uses the parameters shown in Table 94 (page 103). Table 94 Parameters for Inflow-Control Operation Parameter Description Enable The cache memory is used. Disable The cache memory is not used. Normal end The operation has ended normally. Seq.
PAGE 104
Table 96 UnitePathGroup Operation Item Description PathGroup The path group number of the original path group. TargetPathGroup The path group number of the path group merged into the original path group. Result The result of the operation. Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of PathGroups The number of the path groups merged. WwnTimer Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Ext Stor],WwnTimer,,Normal end,,,Seq.
PAGE 105
20 FC Function Set SCP Time Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx,00:00,[FC],Set SCP Time,,Normal end,,,Seq.=xxxxx +{LDKC,CU,SCP Time(s)}= -[{0x00,0x00,600},{0x00,0x01,600},{0x00,0x02,600},{0x00,0x03,600},{0x00,0x04,600}, (snip), {0x00,0xFE,600}],Num. of CUs=255 [FC] FlashCopy function Set SCP Time Set State Change Pending (SCP) Time operation Normal end The operation has ended normally. Seq.
PAGE 106
21 Information Function Delete Log Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xx, 00:00,[Information],Delete Log,SIM,Normal end,,,Seq.=xxxxx [Information] Information function Delete Log Delete Log operation SIM SIM is the selected parameter. This operation uses the following parameters, as shown in Table 99 (page 106). Table 99 Parameters for Delete Log Operation Parameter Description SIM The deletion of SIM log. SSB The deletion of SSB log. Reset The deletion of Reset log.
PAGE 107
Information function ORM Value ORM Value operation Alter and Error Reset Alter is the selected parameter for example 1 and Error Reset is the selected parameter for example 2. This operation uses the following parameters, as shown in Table 100 (page 107). Table 100 Parameters for ORM Value Operation Parameter Description Alter Change the threshold of ORM (Online Read Margin). Error Reset Indicates Error Reset. Normal end The operation has ended normally. Seq.
PAGE 108
Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 102 (page 108). Table 102 SIM Complete Operation Item Description Reference Code The SIM reference code of the error and service request. Num. of Reference Codes The number of SIM reference codes. SIM Reporting Option Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.
PAGE 109
Table 103 SIM Reporting Option Operation (continued) Item Description Service Report service level information as SIM. ON: Report, OFF: Do not report Num. of Types The number of information levels to be reported as SIM. Threshold Value Operation Example 1 user-name,xx,YYYY/MM/DD,HH:MM:SS.xx, 00:00,[Information],Threshold Value,Alter,Normal end,,,Seq.=xxxxx +Type=7days +{Mechanical error(Recovered,Unrecd.),Media error(Recovered,Unrecd.), Read/Write error(Recovered,Unrecd.
PAGE 110
Table 105 Threshold Value Operation (Example 1) (continued) Item Description Read/Write error The threshold of Read/Write error. (Recovered,Unrecd.) Drive I/F error The threshold of Drive I/F error. (Recovered,Unrecd.) Controller hardware The threshold of Controller hardware error. error (Recovered,Unrecd.) 110 FC I/F error Port 0 (Unrecd.) The threshold of FC I/F error Port 0. FC I/F error Port 1 (Unrecd.) The threshold of FC I/F error Port 1. Port 0 error (Unrecd.) The threshold of Port 0 error.
PAGE 111
22 Install Function Add Host Group Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Install],Add Host Group,,Normal end,,,Seq.=xxxxx +{Port,HostGrpID,HostGrpName,Mode,Option[0:31],Option[32:63],Option[64:95]}={XX, 0xXXX,XXXXXXXXXXXXXXXX,0xXX,0xXXXXXXXX,0xXXXXXXXX,0xXXXXXXXX} ++{WWN,Nickname}=[{0xXXXXXXXXXXXXXXXX,XXXXXXXXXXXXXXXX},{0xXXXXXXXXXXXXXXXX, XXXXXXXXXXXXXXXX}],Num.
PAGE 112
The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 107 (page 112).
PAGE 113
Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 109 (page 113). Table 109 All Config Operation Item Description New Ver. The new version number. Old Ver. The old version number. Assist Config Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx,GMT,[Install],Assist Config,,Normal end,,,Seq.=xxxxx +{New Ver.,Old Ver.
PAGE 114
Table 111 Backup Config Operation Item Description Ver. The version number of the configuration information to be backed up. Change Host Group Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Install],Change Host Group,,Normal end,,,Seq.=xxxxx +{Port,HostGrpID,HostGrpName}=[{XX,XXX,XXXXXXXXXXXXXXXX},{XX,XXX,XXXXXXXXXXXXXXXX}], Num. of Host Groups=2 [Install] Install function Change Host Group Change Host Group operation Normal end The operation has ended normally. Seq.
PAGE 115
Table 113 Change WWN Operation Item Description Port The name of the port where the host is connected. HostGrpID The host group number on which the host with WWN or nickname of the host bus adapter being changed is registered. WWN Indicates WWN of the host bus adapter before change. Change WWN Indicates WWN of the host bus adapter after change. Change Nickname The nickname of the host bus adapter after change. Num.
PAGE 116
Detailed Information Detailed information displays for this operation, as shown in Table 114 (page 116). Table 114 Delete DKC WWN Operation Item Description Port The port name where the host of WWN deleted from WWN list was connected. Delete WWN Indicates WWN deleted from WWN list. WWN is a 16-digit number in the hexadecimal format. Num. of WWNs The number of WWNs deleted. Delete Host Group Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Install],Delete Host Group,,Normal end,,,Seq.
PAGE 117
Table 116 Delete LU Path Operation Item Description Port The name of the port where the host group is created HostGrpID The host group number where the LU path is deleted LUN Indicates LUN where the LU path assignment is cancelled LDKC:CU:LDEV The LDKC, CU, and LDEV number of the volume where the LU path assignment is cancelled Num. of Paths The number of LU paths deleted Delete WWN Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Install],Delete WWN,,Normal end,,,Seq.
PAGE 118
Detailed Information Detailed information displays for this operation, as shown in Table 118 (page 118). Table 118 DKU Emulation Operation Item Description Type The emulation type LDEV(LDKC:CU:LDEV) The LDKC, CU, and LDEV numbers where the emulation type is changed Num. of LDEVs The number of logical volumes where the emulation type is changed Types The number of emulation types Force Reset Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Install],Force Reset,,Normal end,,,Seq.
PAGE 119
Detailed information displays for this operation, as shown in Table 120 (page 119). Table 120 Format Operation Item Description PG The parity group number. Num. of PGs The number of parity groups. LDEV The LDEV number. Num. of LDEVs The number of LDEVs. Format Stop Operation This log information is output when the format process is suspended. user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Install],Format Stop,,Normal end,,,Seq.=xxxxx +PG=[1-1],Num. of PGs=1 +PG=[E1-1],Num.
PAGE 120
Install Operation Example 1 (installing additional channel adapters) user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Install],Install,,Normal end,,,Seq.
PAGE 121
user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Install],Install,,Normal end,,,Seq.=xxxxx +{DKA,Kind,Transfer Rate}=[{DKA-1AL,DKF 4MP,4},{DKA-1BL,DKF 4MP,4},{DKA-2ML,DKF 4MP,4}, {DKA-2NL,DKF 4MP,4}],Num. of DKAs=4 +{DKU,AC-BOX}=[{DKU-R1,3-phase AC Box(30A)}],Num. of DKUs=1 +FSW=[FSWR10-L,FSWR10-U,FSWR11-L,FSWR11-U,FSWR12-L,FSWR12-U,FSWR13-L,FSWR13-U,FSWR18-L, FSWR18-U,FSWR19-L,FSWR19-U,FSWR1A-L,FSWR1A-U,FSWR1B-L,FSWR1B-U],Num.
PAGE 122
Table 124 Install Operation (Installing Additional Subsystems, ECC Groups or LDEVs) (continued) Item Description AC-BOX The type of AC-BOX Num. of Disk Units (DKU) The number of Disk Units (DKU) FSW The mounting location of the fibre switch. Num. of FSWs The number of FSWs PG The parity group number RAID Level The RAID Level Drive Type The type of the drive Emulation The emulation type Concatenation The RAID concatenated parity group number.
PAGE 123
Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 125 (page 123). Table 125 Install Operation (Installing Additional Cache Memory) Item Description CM The mounting location of the PCB for cache memory. CMG The capacity of CMG. Size The capacity of cache memory. On-Demand The capacity of On-Demand. Num. of CMs The number of cache memory.
PAGE 124
Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 126 (page 124). Table 126 Install Operation (Installing Additional Shared Memory) Item Description SM The mounting location of the PCB for shared memory. Slot The slot position of the shared memory module. Size The capacity of the cache memory module. Num of SMMs The number of shared memory modules. PP Flag The option flags.
PAGE 125
Install function Install Install operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 128 (page 125). Table 128 Install Operation (Installing Additional Battery) Item Description Power Lost Mode The operation when power supply is lost.
PAGE 126
Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information If enabled, detailed information displays for this operation, as shown in Table 130 (page 126). Table 130 Install CV Operation Item Description PG The parity group number LDKC:CU:LDEV The LDKC, CU, and LDEV numbers SLOT The slot number Emulation The emulation type Size The CV capacity Unit The CV unit capacity System Disk The setting status of system disk Disable or Enable will appear.
PAGE 127
Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 132 (page 127). Table 132 Make LUSE Operation Item Description LUSE(LDKC:CU:LDEV) The LDKC, CU, and LDEV numbers of several LDEVs combined into a LUSE volume. The number indicated at the beginning represents the LDKC, CU, and LDEV numbers of the top LDEV. Num.
PAGE 128
Table 134 Make Vol./Vol. Init Item Description PG The parity group number LDKC:CU:LDEV The LDKC, CU, and LDEV numbers Emulation The emulation type Size The capacity of CV Unit The unit of the capacity of CV System Disk The setting status of system disk Disable or Enable will appear. SSID The subsystem ID Num. of LDEVs The number of LDEVs Micro Program Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx,GMT,[Install],Micro Program,,Normal end,,,Seq.
PAGE 129
Table 135 Micro Program Operation (continued) Item Description New Ver The new version number of the microcode. Num.of Kind The number of the kind of microcode. MP Install Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx,GMT,[Install],MP Install,,Normal end,,,Seq.=xxxxx +Micro Program={Minimum Config,DKCMAIN,RAMBOOT,LCP,HTP,LCDG,FCDG}, Num. of Kind=7 +Target MP={CHP00-1E,CHP01-1E,DKP80-1A},Num.
PAGE 130
Table 137 M/F DCR Operation Item Description LDKC:CU:LDEV The LDKC, CU, and LDEV numbers of the logical volume (for a mainframe system) where Cache Residency is set Define The setting status of Cache Residency Set: set, Delete: cancel Mode The setting mode of Cache Residency - Indicates a dash (-) when Define is Delete Bind: Bind mode, Priority: Priority mode Prestaging Indicates whether the Prestaging mode set is enabled or disabled. Indicates a dash (-) when Define is Delete.
PAGE 131
Open DCR operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 139 (page 131).
PAGE 132
Table 140 Patch Edit Operation Item Description Block The block number. File The file information. Old: old data, New: new data. Entry The entry number. Ctl. The control information. 00: Invalid, 20: End in sector, 40: End of patch, 80: Valid Address The address. Old Data The old data. New Data The new data. Sum The sum value. Comment The comment information. Num. of Data The number of data. Num. of Blocks The number of blocks. Release LUSE Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.
PAGE 133
Restore Config. operation SVP&DKC SVP&DKC is the selected parameter. The restoration of configuration information for SVP and DKC. Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Example 2 user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Install],Restore Config.,,Normal end,,,Seq.=xxxxx +{New Ver.,Old Ver.}={xx-xx-xx/xx,xx-xx-xx/xx} [Install] Install function Restore Config. Restore Config.
PAGE 134
Table 143 Set Battery Life Operation Item Description Use Battery Life The status of Battery life function set. Valid: Valid, Invalid: Invalid Date Indicates the date of the setting in YYYY/MM/DD format (YYYY: year, MM: month, DD: day). A hyphen (-) is indicated when the information is not set. Remained Life The remaining date of the battery shelf life. A hyphen (-) is indicated when the information is not set. Set Channel Speed Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.
PAGE 135
Table 145 Set CommandDev Operation Item Description LDKC:CU:LDEV The LDKC, CU, and LDEV numbers of the logical volume where the command device is set CommandDev Indicates whether the command device setting is enabled or disabled Disable or Enable will appear. Num. of LDEVs The number of logical volumes where the command device is set Set Command Device Security (CommandDevSec) Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Install],Set CommandDevSec,,Normal end,,,Seq.
PAGE 136
Detailed Information Detailed information displays for this operation, as shown in Table 147 (page 136). Table 147 Set Fibre Address Operation Item Description Port The name of the port that the fibre address has been set. Fibre Addr. The address of Fibre Channel port after change using a number from 1 to 126. See “Output Values to Detailed Info and Addresses of Fibre Channel Port” (page 161) for relation of number and Fibre Channel port address. Num.
PAGE 137
The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 149 (page 137). Table 149 Set Host Mode Operation Item Description Port The name of the port where the host group is created. HostGrpID The host group number. Mode The host mode set. See the HP StorageWorks XP24000/XP20000 LUN Manager User Guide for the meaning of the host mode number.
PAGE 138
Table 151 Set IP Address Operation Item Description IP Add The IP address in SVP. Subnet The subnet mask in SVP. Use Duplex Indicates whether the Duplex setting in SVP is valid or invalid. Valid: Valid, Invalid: Invalid SVP Kind The kind of duplicated SVP. Master SVP: Master SVP, Standby SVP: Standby SVP. IPv4 The status of IPv4. Valid: enabled, Invalid: disabled. IPv6 The subnet mask of IPv6. Valid: enabled, Invalid: disabled.
PAGE 139
Set Speed Mode Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Install],Set Speed Mode,,Normal end,,,Seq.=xxxxx +CHA=CHA-1E ++{Port Block,Mode}=[{A,High Speed},{B,High Speed}Num. of Blocks=2 +CHA=CHA-1H ++{Port Block,Mode}=[{A,Standard},{B,High Speed}],Num. of Blocks=2 +Num. of CHAs=2 [Install] Install function Set Speed Mode Set Speed Mode operation Normal end The operation has ended normally. Seq.
PAGE 140
Table 154 Parameters for Set Subsystem Time Operation Parameter Description TOD Change The date and the time. Synchro. Infor. The setting of time correction function. Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 155 (page 140).
PAGE 141
Table 156 System Option Operation Item Description Spare Disk Recover Indicates the setting status of Spare Disk Recover. Interleave: Give priority to the access from the host while executing copy process, Full speed: Give priority to the copy process. Disk Copy Pace Indicates the setting status of Disk Copy Pace. Slower: Low speed, Medium: Medium speed, Faster: High speed Copy Operation Indicates the setting status of Copy Operation (Correction Copy).
PAGE 142
Table 156 System Option Operation (continued) Item Description Debug Mode Setting executed from the debug window (Set: fix). NOTE: Only the changed items will be output. System Tuning Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Install],System Tuning,,Normal end,,,Seq.=xxxxx +Serial No.=64040 +IP Address Mode=Based on Serial Number +IP Address=126.132.248 +Subnet Mask=255.0.0 +WDCP=ON +DDUMP=ON +Power Supply Type=3-phase AC Box(40A) +{DKU,AC-BOX}=[{DKU-R1,1-phase AC Box(50A)}],Num.
PAGE 143
Table 157 System Tuning Operation (continued) Item Description Transfer Rate The Disk Adapter (DKA) transfer rate. Num.of DKAs The number of Disk Adapters (DKA). LDKC:CU The LDKC number and the CU number. LDEV The LDEV number. SSID The subsystem ID. Num of SSIDs The number of subsystem IDs. Uninstall Operation Example 1 (uninstalling a CHA) user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Install],Uninstall,,Normal end,,,Seq.
PAGE 144
Detailed Information Detailed information displays for this operation, as shown in Table 159 (page 144). Table 159 Uninstall Operation (Uninstalling a DKA, an ECC Group or an LDEV) Item Description Disk Adapter (DKA) The Disk Adapter (DKA) mounting location. Kind The type of Disk Adapter (DKA). Num. of Disk Adapters (DKA) The number of Disk Adapters (DKA). Disk Unit (DKU) The Disk Adapter (DKA) mounting location. Num. of Disk Units (DKU) The number of subsystems.
PAGE 145
Table 160 Uninstall Operation (Uninstalling a Cache Memory Module) Item Description CM The mounting location of the PCB for cache memory. CMG The capacity of CMG. Size The capacity of cache memory. On-Demand The capacity of On-Demand. Num. of CMs The number of cache memory. DCR available size The capacity of Cache Residency. CLPR The CLPR number. Cache size The capacity of the cache memory allocated to CLPR. DCR size The capacity of Cache Residency allocated to CLPR.
PAGE 146
Table 161 Uninstall Operation (Uninstalling a Shared Memory Module) Item Description SM The mounting location of the PCB for shared memory. Slot The slot position of the shared memory module. Size The capacity of the cache memory module. Num of SMMs The number of shared memory modules. PP Flag The flags of the options. Num of PP Flags The number of the flags of the options. Max Number of CUs The maximum number of CUs.
PAGE 147
Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 163 (page 147). Table 163 Uninstall Operation (Uninstalling a Battery) Item Description Power Lost Mode The operation when power supply is lost. Memory Backup Mode: Set to Memory Backup Mode Destage Mode: Set to Destage Mode Battery The mounting location of the battery Num.
PAGE 148
Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 165 (page 148). Table 165 Volume to Space Operation 148 Item Description PG The parity group number. LDKC:CU:LDEV The LDKC number, the CU number and LDEV number. Num. of LDEVs The number of LDEVs.
PAGE 149
23 LDEV Function Volume-Blockade Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[LDEV],Volume-Blockade,,Normal end,,,Seq.=xxxxx +LDKC:CU:LDEV=[0x00:0x00:0x01,0x00:0x00:0x02,0x00:0x00:0x03,0x00:0x00:0x04,0x00:0x00:0x05, 0x00:0x00:0x06,0x00:0x00:0x07,0x00:0x00:0x08,0x00:0x00:0x09,0x00:0x00:0x0A], [LDEV] Logical Device function Volume-Blockade Volume-Blockade operation Normal end The operation has ended normally. Seq.
PAGE 150
NOTE: The status does not change immediately after you execute an LDEV operation command. As a result, errors may occur after you execute the command. Volume-Format(H) Operation The logged information indicates that the Format operation was only requested, but not finished. user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[LDEV],Volume-Format(H),,Normal end,,,Seq.
PAGE 151
Table 169 Volume-Format(Q) Operation Item Description LDKC:CU:LDEV The LDKC number, the CU number, and LDEV number Num. of LDEVs The number of LDEVs being set NOTE: The status does not change immediately after you execute an LDEV operation command. As a result, errors may occur after you execute the command. Volume-Restore(N) Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[LDEV],Volume-Restore(N),,Normal end,,,Seq.
PAGE 152
24 LUNM Function Add Host Group Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx,00:00,[LUNM],Add Host Group,,Normal end,,,Seq.=xxxxx +{Port,HostGrpID,HostGrpName}=[{XX,0xXXX,XXXXXXXXXXXXXXXX},{XX,0xXXX, XXXXXXXXXXXXXXXX}], Num.of Host Groups=2 [LUNM] LUN Manager function Add Host Group Add Host Group operation Normal end The operation has ended normally. Seq.
PAGE 153
Table 172 Add LU Path (continued) Item Description LUN Indicates LUN of the logical volume linked to the host group LDKC:CU:LDEV The LDKC, CU, and LDEV numbers of the logical volume linked to the host group Num. of Paths The number of LU paths set Add World Wide Name (WWN) Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[LUNM],Add WWN,,Normal end,,,Seq.=xxxxx +{Port,HostGrpID,WWN,Nickname }=[{XX,0xXXX,0xXXXXXXXXXXXXXXXX,XXXXXXXXXXXXXXXX}, {XX,0xXXX,0xXXXXXXXXXXXXXXXX,XXXXXXXXXXXXXXXX}],Num.
PAGE 154
Table 174 Change Host Group Operation Item Description Port The name of the port where the host group is created. HostGrpID The host group number where the name or host modes have been changed. HostGrpName The name of the host group. If the name is changed, the name after change is indicated. Num. of Host Groups The number of host groups where the settings have been changed. Change WWN Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[LUNM],Change WWN,,Normal end,,,Seq.
PAGE 155
Detailed Information Detailed information displays for this operation, as shown in Table 176 (page 155). Table 176 Delete DKC WWN Operation Item Description Port The port name where the host of WWN deleted from WWN list was connected. Delete WWN Indicates WWN deleted from WWN list. WWN is a 16-digit number in the hexadecimal format. Num. of WWNs The number of WWNs deleted. Delete Host Group Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[LUNM],Delete Host Group,,Normal end,,,Seq.
PAGE 156
Table 178 Delete LU Path Operation Item Description Port The name of the port where the host group is created. HostGrpID The host group number where the LU path is deleted. LUN Indicates LUN where the LU path assignment is cancelled. Num. of Paths The number of LU paths deleted. Delete World Wide Name (WWN) Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00, [LUNM],Delete WWN,,Normal end,,,Seq.=xxxxx +{Port,HostGrpID,WWN}=[{XX,0xXXX,0xXXXXXXXXXXXXXXXX},{XX,0xXXX,0xXXXXXXXXXXXXXXXX}], Num.
PAGE 157
Table 180 Set Channel Speed Operation Item Description Port The name of the port that the host speed (data transfer speed) is set. Speed(Gbps) The host speed set. The unit is Gbps (Gigabits per second). When Auto is set for the host speed, Auto is output. Num. of Ports The number of ports where the host speed is set. Set Command Device (CommandDev) Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[LUNM],Set CommandDev,,Normal end,,,Seq.
PAGE 158
Table 182 Set CommandDev Sec Operation Item Description LDKC:CU:LDEV The LDKC, CU, and LDEV numbers of the logical volume where the command device security setting is changed CommandDevSec Indicates whether the command device security setting is enabled or disabled Disable or Enable will appear Num. of LDEVs The number of logical volumes that the command device security setting is changed Set Fibre-Channel Security Protocol (FCSP) Host Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.
PAGE 159
The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 184 (page 159). Table 184 Set FCSP Port Info Operation Item Description Port The name of the port where authentication parameter has been set. Auth_TOV The time to execute authentication after the failure of port authentication. The unit is second.
PAGE 160
Set Fibre-Channel Security Protocol (FCSP) Target Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[LUNM],Set FCSP Target,,Normal end,,,Seq.=xxxxx +{Port,HostGrpID,Switch,DH Group,UserName}=[{1E,0x01,Enable,0,1111111111111111}, {3E,0x01,Disable,0,2222222222222222}],Num. of Grps=2 [LUNM] LUN Manager function Set FCSP Target Set FCSP Target operation Normal end The operation has ended normally. Seq.
PAGE 161
Table 187 Set Fibre Address Item Description Port The name of the port that the address has been changed. Fibre Addr The address of Fibre Channel port after change using a number from 1 to 126. See Table 188 (page 161) for relation of number and Fibre Channel port address. Num. of Ports The number of ports where address has been changed. Table 188 Output Values to Detailed Info and Addresses of Fibre Channel Port Value Add.1 Value Add.1 Value Add.1 Value Add.
PAGE 162
Table 188 Output Values to Detailed Info and Addresses of Fibre Channel Port (continued) Value Add.1 Value Add.1 Value Add.1 Value Add.1 30 B5 (29) 62 75 (61) 94 45 (93) 126 01 (125) 31 B4 (30) 63 74 (62) 95 43 (94) - - 32 B3 (31) 64 73 (63) 96 3C (95) - - 1 Addresses outside parentheses = arbitrated-loop physical address (AL-PA). Addresses in parentheses = loop IDs. Set Fibre Topology Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.
PAGE 163
Detailed Information Detailed information displays for this operation, as shown in Table 190 (page 163). Table 190 Set Host Mode Operation Item Description Port The name of the port where the host group is created. HostGrpID The host group number. Mode The host mode set. See the HP StorageWorks XP24000/XP20000 LUN Manager User Guide for the meaning of the host mode number. Option[0:31] The host mode option set. 96 host mode options from 0 to 95 are configured, and then are output in units of 32.
PAGE 164
Table 192 Host mode options 32 to 63 and output values of Option[32:63] (continued) Host Mode Option Values of option[0:31] Host Mode Option Values of option[0:31] Host Mode Option Values of option[0:31] 39 0x01000000 50 0x00002000 61 0x000000004 40 0x00800000 51 0x00001000 62 0x000000002 41 0x00400000 52 0x00000800 63 0x000000001 42 0x00200000 53 0x00000400 Table 193 Host mode options 64 to 95 and output values of Option[64:95] Host Mode Option Values of option 0:31] Host Mode
PAGE 165
Table 194 Set Security Switch Operation Item Description Port The name of the port where the LUN security setting is changed. Switch Indicates whether the LUN security setting is enabled or disabled. Disable or Enable is output. Num. of Ports The number of ports where the LUN security setting is changed. Set Speed Mode Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[LUNM],Set Speed Mode,,Normal end,,,Seq.=xxxxxx +CHA=CHA-1EL ++{Port Block,Mode}=[{A,Standard},{B,High Speed/MIX}],Num.
PAGE 166
Detailed information displays for this operation, as shown in Table 196 (page 166). Table 196 Set UUID Operation Item Description LDKC:CU:LDEV The LDKC number, CU number, and LDEV number UUID User Definable LUN ID Num.
PAGE 167
25 LUSE Function Make LUSE Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[LUSE],Make LUSE,,Normal end,,,Seq.=xxxxx +{LUSE(LDKC:CU:LDEV)}=[{0x00:0x00:0x00,0x00:0x00:0x01,0x00:0x00:0x02, 0x00:0x00:0x03}, {0x00:0x01:0x00,0x00:0x01:0x01,0x00:0x01:0x02,0x00:0x01:0x03}], Num. of LUSEs=2 [LUSE] Logical Unit Number Expansion function Make LUSE Logical Unit Number Expansion operation Normal end The operation has ended normally. Seq.
PAGE 168
26 Maintenance Function Blockade Operation Example 1 (blocking a Cluster) user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Maintenance],Blockade,,Normal end,,,Seq.=xxxxx +Location=Cluster-1 Example 2 (blocking a PCB) user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Maintenance],Blockade,,Normal end,,,Seq.=xxxxx +PCB=[CHA-1P],Num. of PCBs=1+ PDEV=HDD00-01 Example 3 (blocking an LDEV) user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Maintenance],Blockade,,Normal end,,,Seq.=xxxxx +PG=[1-1],Num. of PGs=1 +PG=[E1-1],Num.
PAGE 169
Correction Copy operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 200 (page 169). Table 200 Correction Copy Operation Item Description PDEV The mounting location of the PDEV (physical device). Drive Interrupt Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Maintenance],Drive Interrupt,,Normal end,,,Seq.
PAGE 170
Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 202 (page 170). Table 202 Format Operation Item Description PG The parity group number. Num. of PGs The number of parity groups. LDEV The LDEV number. Num. of LDEVs The number of LDEVs. NOTE: The status does not change immediately after you execute an LDEV operation command. As a result, errors may occur after you execute the command.
PAGE 171
[Maintenance] Maintenance function Pre Quick Format Stop Pre Quick Format Stop operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 204 (page 171). Table 204 Pre Quick Format Stop Operation Item Description PG The parity group number. Num. of PGs The number of parity groups. LDEV The LDEV number. Num. of LDEVs The number of LDEVs.
PAGE 172
Recover Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Maintenance],Recover,,Normal end,,,Seq.=xxxxx +Location=Cluster-1 [Maintenance] Maintenance function Recover Recover operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 206 (page 172). Table 206 Recover Operation Item Description Location The cluster to be recovered.
PAGE 173
Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 207 (page 173).
PAGE 174
Restore Restore operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 208 (page 174). Table 208 Restore Operation Item Description PCB The mounting location of the PCB CHA, DKA, CM, SM, CSW, MIX or BASE) to be restored. PDEV The location of the PDEV to be restored. PG The parity group number. Num. of PGs The number of parity groups.
PAGE 175
Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 210 (page 175). Table 210 Size Change Operation Item Description PCB The mounting location of the PCB ( CM) to be replaced. Num. of PCBs The number of PCBs to be replaced. SIZE The capacity of cache memory. Battery The mounting location of the battery to be replaced.
PAGE 176
Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Transfer Config Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Maintenance],Transfer Config,,Normal end,Seq.=xxxxx [Maintenance] Maintenance function Transfer Config Transfer Config operation Normal end The operation has ended normally. Seq.
PAGE 177
Verify Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Maintenance],Verify,,Normal end,,,Seq.=xxxxx +PG=[1-1],Num. of PGs=1 +LDEV=[0x00:0x03:0x2f],Num. of LDEVs=1 [Maintenance] Maintenance function Verify Verify operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 213 (page 177).
PAGE 178
27 OND Function Release Cache/CLPR Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[OND],Release Cache/CLPR,,Normal end,,,Seq.=xxxxx +Cache(MB)=258048 ++{CLPR,Cache(MB)}=[{01,4096},{02,4096},{03,4096},{04,4096},{05,4096},{06,4096},{07,4096}, {08,4096},{09,4096},{10,4096},{11,4096},{12,4096},{13,4096},{14,4096}, -{15,4096},{16,4096},{17,4096},{18,4096},{19,4096},{20,4096},{21,4096},{22,4096},{23,4096}, {24,4096},{25,4096},{26,4096},{27,4096},{28,4096},{29,4096},{30,4096}, -{31,4096}],Num.
PAGE 179
28 XP Performance Control (Perf Ctrl) Function Change XP Performance Control Group (PerfCtrlGrp) Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[PerfCtrl],Change PerfCtrlGrp,,Normal end,,,Seq.=xxxxx +{PPC Group, Priority,UpperLimit,Mode}=[{XXXXXXXXXXXXXXXX,Non-Prio,XXXXXXXX,IOPS}], Num. of PPC Groups=1 [Perf Ctrl] XP Performance Control (Perf Ctrl) function Change PerfCtrlGrp Change XP Performance Control Group (PerfCtrlGrp) operation Normal end The operation has ended normally. Seq.
PAGE 180
[Perf Ctrl] XP Performance Control (Perf Ctrl) function Default Set Default Set operation Kind=WWN WWN is selected as the parameter. This operation uses the following parameters, as shown in Table 217 (page 180). Table 217 Parameters for Default Set Operation Parameter Description Port The setting for the port tab is initialized. WWN The setting for the WWN tab is initialized. Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295).
PAGE 181
Set All Priority (Prio) Port Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00 [Perf Ctrl],Set All Prio Port,,Normal end,,, Seq.=xxxxx +{AllPriority,Treshold,Mode}={Enable,XXXXXXXX,IOPS} [Perf Ctrl] XP Performance Control (Perf Ctrl) function Set All Prio Port Set All Prio Port operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295).
PAGE 182
Table 220 Set All Prio WWN Operation Item Description AllPriority The setting status of the All Thresholds value in the WWN tab Enable: All Thresholds value is set Disable: All Thresholds value is cancelled Threshold The All Thresholds value set. This value is output only when the All Thresholds value is set Mode The rate type of the All Thresholds value. IOPS: I/O rate, KB/s: Transfer rate This value is output only when the All Thresholds value is set.
PAGE 183
Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 222 (page 183). Table 222 Set Prio Port Operation Item Description Port The port name. Priority The attribute set to the port. Prio: Prioritized port, Non-Prio: Non-prioritized port Use The channel type of path interface.
PAGE 184
Table 223 Set Prio WWN Operation (continued) Item Description Mode The type of rate used for the upper limit control. IOPS: I/O rate, KB/s: Transfer rate. This value is not output when the attribute is set to prioritized WWN. Num. of WWNs The number of WWNs of the host bus adapters that the setting is changed. WWN Indicates WWN of the host bus adapter. WWN is a 16-digit number in the hexadecimal format. Update Port WWN Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.
PAGE 185
Update PerfCtrlGrp Update PerfCtrlGrp operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 225 (page 185). Table 225 Update PerfCtrlGrp Operation Item Description UpdateMode The operation executed. Add New Group: Creation of an Perf Ctrl group. Add WWN: Addition of the host bus adapter to the Perf Ctrl group.
PAGE 186
Detailed information displays for this operation, as shown in Table 226 (page 186). Table 226 Update WWN Operation Item Description UpdateMode The operation executed. Change WWN: Change of host bus adapter. Change Nickname: Change of Perf Ctrl name of the host bus adapter WWN Indicates WWN of the host bus adapter. WWN is a 16-digit number in the hexadecimal format. When the host bus adapter is changed, the WWN of the host bus adapter before change is output.
PAGE 187
29 Performance Monitor Function Monitoring S/W Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx,00:00,[Perf Mon],Monitoring S/W,Enable 60sec,,Normal end,,,Seq.=xxxxx [Perf Mon] Performance Monitor function Monitoring S/W Monitoring Options operation Enable 60sec Enable 60sec is the selected parameter. The operation uses the following parameters, as shown in Table 227 (page 187).
PAGE 188
30 PORT Function Change Port Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[PORT],Change Port,,Normal end,,,Seq.=xxxxx +Attribute=RCU Target ++Port=[1E,3E,5E,7E], Num.of Ports=4 [PORT] PORT function Change Port Change Port operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 229 (page 188).
PAGE 189
31 Optional PP KEY Function PP Apply Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[PP KEY],PP Apply,,Normal end,,,Seq.=xxxxx [PP KEY] Optional Product License Key function PP Apply PP Apply operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) PP Available Install Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[PP KEY],PP Available Install,,Normal end,,, Seq.=xxxxx +{P.P.Name,Result}=[{JAVA API,Normal end}],Num.
PAGE 190
Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 231 (page 190). Table 231 PP Disable chk Operation Item Description P.P.Name The name of the disabled option. Result The result of checking the disabled option. Num. of PPs The number of the disabled options. PP Enable chk Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[PP KEY],PP Enable chk,,Normal end,,,Seq.=xxxxx +{P.P.
PAGE 191
Table 233 PP Install chk Operation Item Description Key Code The key code used for installation. P.P.Name The name of the installed option. Result The result of installation. Num. of PPs The number of the installed options. PP Install File chk Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[PP KEY],PP Install File chk,,Normal end,,,Seq.=xxxxx +File Name=C:\Dkc200\Home\Sample.plk ++{P.P.Name,Result}=[{JAVA API,Normal end}, -{LUN Manager,Normal end}],Num.
PAGE 192
Table 235 PP Uninstall chk Operation Item Description P.P.Name The name of the uninstalled option. Result The result of file check in the uninstallation. Num. of PPs The number of the uninstalled options. SLPR PP Change Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx,00:00,[PP KEY],SLPR PP Change,,Normal end,,,Seq.=xxxxx +{P.P.Name,SLPR#,License Capa(GB)}=[{JAVA API,XX,ZZZZZ00},{LUN Manager,XX,ZZZZZ00}], Num.
PAGE 193
32 RCU Function Add Path Operation Example 1 (CU Free is used) user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[RCU],Add Path,,Normal end,,,Seq.=xxxxx +{S/N,MCU LDKC,RCU LDKC,Path Gr.ID,Controller ID}={99999,0x00,0x00,Default,4} ++{MCU Port,RCU Port}=[{1E,3E},{5E,7E},{1F,3F},{5F,7F},{1G,3G},{5G,7G},{1H,3H},{5H,7H}], Num of Port Pairs=8 Example 2 (CU Free is not used) user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[RCU],Add Path,,Normal end,,,Seq.
PAGE 194
user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[RCU],Add RCU,,Normal end,,,Seq.=xxxxx +{S/N,MCU LDKC,MCU,RCU LDKC,RCU,SSID,Controller ID,Min.Path,MIH Time(s), Round Trip Time(ms),Incident,FREEZE}={99999,0x00,0x3F,0x00,0x7F,0x0004,4,08,015,001, only to RCU host,Disable} ++{MCU Port,RCU Port}=[{1E,3E},{5E,7E},{1F,3F},{5F,7F},{1G,3G},{5G,7G},{1H,3H},{5H,7H}], Num of Port Pairs=8 [RCU] Remote Control Unit function Add RCU Add Remote Control Unit operation Normal end The operation has ended normally. Seq.
PAGE 195
user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[RCU],Change RCU Option,,Normal end,,,Seq.=xxxxx +{S/N,MCU LDKC,RCU LDKC,Path Gr.ID,Controller ID,Min.Path,MIH Time(s),Round Trip Time(ms),Incident, FREEZE}={99999,0x00,0x00,Default,4,08,015,001,only to RCU host,Disable} Example 2 (CU Free is not used) user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[RCU],Change RCU Option,,Normal end,,,Seq.=xxxxx +{S/N,MCU LDKC,MCU,RCU LDKC,SSID,Controller ID,Min.
PAGE 196
user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[RCU],Delete Path,,Normal end,,,Seq.=xxxxx +{S/N,MCU LDKC,MCU,RCU LDKC,RCU,SSID,Controller ID}={99999,0x00,0x3F,0x00,0x7F,0x0004,5} ++{MCU Port,RCU Port}=[{1E,3E},{5E,7E},{1F,3F},{5F,7F},{1G,3G},{5G,7G},{1H,3H},{5H,7H}], Num of Port Pairs=8 [RCU] Remote Control Unit function Delete Path Delete Path operation Normal end The operation has ended normally. Seq.
PAGE 197
Detailed Information Detailed information displays for this operation, as shown in Table 241 (page 197). Table 241 Delete RCU Operation Item Description S/N The serial number of the device of RCU deleted. MCU LDKC The LDKC number of the connected LDKC. RCU LDKC The LDKC number of the paired LDKC. Path Gr.ID The path group ID of the RCU deleted. When the path group ID is a default setting, Default is output. Controller ID The controller ID of the RCU deleted.
PAGE 198
33 Volume Shredder Function End Shredding Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Shredder],End Shredding,,Normal end,,, Seq.=xxxxx +{Times,Result}=[{1,Nomal},{2,Nomal},{3,Error}],Num. of Data=3 [Shredder] Volume Shredder function End Shredding End Shredding operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 242 (page 198).
PAGE 199
Detailed information displays for this operation, as shown in Table 243 (page 199). Table 243 Set Shredding Operation Item Description OwnerID The owner ID. 0: Indicates Remote Web Console 0xXX: Owner ID is expressed in two digits of the hexadecimal format Data The data type. Random: Random, 0xXXXX: Define Output File Indicates whether the result of shredding is output to the file. Disable: No output, Enable: Output Num. of Data The number of data types.
PAGE 200
34 SI for Mainframe Function Add Pair Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[SI],Add Pair,,Normal end,,,Seq.=xxxxx +Copy Pace=Faster ++{S-VOL(LDKC:CU:LDEV),T-VOL(LDKC:CU:LDEV),Result}=[{0xXX:0xAA:0xBB,0xYY:0xCC:0xDD,0,Normal end}, {0xXX:0xAA:0xBB,0xYY:0xCC:0xDD,1,Error(xxxx-yyyy)}],Num. of Pairs=2 [SI] ShadowImage for Mainframe function (for the IBM z/OS) Add Pair Add Pair operation Normal end The operation has ended normally. Seq.
PAGE 201
Table 246 Change Reserve Operation Item Description Attribute Indicates whether the reserve attribute is set or cancelled Set: the reserve attribute is set, Reset: the reserve attribute is cancelled VOL(LDKC:CU:LDEV) The LDKC, CU, and LDEV numbers of the volume that the reserve attribute is set or cancelled Result The result of operation Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num.
PAGE 202
Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 248 (page 202).
PAGE 203
Table 249 Option Operation Item Description Swap & Freeze Indicates whether the Swap & Freeze option is enabled or disabled. Enable: Option is enabled, Disable: Option is disabled. HOST I/O Performance Indicates whether the host I/O option is enabled or disabled. Enable: Option is enabled, Disable: Option is disabled. FCv2 Slower Copy1 Indicates whether the FCv2 Slower Copy1 option is enabled or disabled. Enable: Option is enabled, Disable: Option is disabled.
PAGE 204
Table 250 Resync Pair Operation (continued) Item Description Result The result of operation. Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Pairs The number of resynchronized pairs Split Pair Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[SI],Split Pair,,Normal end,,,Seq.
PAGE 205
Suspend Pair operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 252 (page 205).
PAGE 206
35 XP Snapshot Function Pairsplit-S Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Snapshot],Pairsplit-S,,Normal end,,,Seq.=xxxxx +{P-VOL(LDKC:CU:LDEV),S-VOL(LDKC:CU:LDEV),MU,Result}=[{0xAA:0xBB:0xCC,0xDD:0xEE:0xFF,00, Normal end},{0xAA:0xBB:0xCC,0xDD:0xEE:0xFF,01,Error(xxxx-yyyy)}],Num. of Pairs=2 [Snapshot] HP XP Snapshot function Pairsplit-S Pairsplit-S operation Normal end The operation has ended normally. Seq.
PAGE 207
36 SNMP Function Set SNMP Agent Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[SNMP],Set SNMP Agent,,Normal end,,,Seq.=xxxxx +Install=Disable +Manager=[(158.214.133.1),(158.214.133.2),(158.214.133.3),(1:0:0:0:0:0:0:1), (snip) -(158.214.133.31),(158.214.133.32),(AAAA:0:0:0:0:0:0:FFFF)],Num. of Managers=xx +Community=1234567891123456789212345678931234567894123456789512345678961234567897123 45678981234567899123456789012345678911234567892123456789312345678941234567895 ++Trap=[(158.214.133.1),(158.214.
PAGE 208
37 TC for Mainframe Function Add CTG Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[TC],Add CTG,,Normal end,,,Seq.=xxxxxx +{LDKC,CTG,Path,Offloading(min.),Inflow Control,Copy Pending(min.),RCU Ready(min.), Timer Type}= {0x00,0x00,Fibre,005,Enable,05,05,System} [TC] TrueCopy for Mainframe function (for IBM z/OS) Add CTG Add Consistency Group operation Normal end The operation has ended normally. Seq.
PAGE 209
The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 256 (page 209).
PAGE 210
Change Async Option Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx,00:00,[TC],Change Async Option,,Normal end,,,Seq.=xxxxxx +{CLPR,Rate(%)}={00,050} [TC] TrueCopy for Mainframe function (for IBM z/OS) Change Async Option Change Async Option operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 257 (page 210).
PAGE 211
Table 258 Change CTG Option Operation (continued) Item Description RCU Ready (min.) The setting value for Time Out (RCU ready). The unit is minute. When Time Out (RCU ready) is set to 0 (zero), None is output. Timer Type The timer type set. System: System timer, Local: Local timer, None: No timer (system timer) Change Option Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[TC],Change Option,,Normal end,,,Seq.
PAGE 212
Table 259 Change Option Operation (continued) Item Description Parallel Initial Copy (CU) The number of parallel operation of initial copy by CU. (1 to 16) Num. of CUs The number of CUs set. Change Pair Option Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx,00:00,[TC],Change Pair Option,,Normal end,Seq.=xxxxxx +{M-VOL(LDKC:CU:LDEV),Fence Level,CFW, Error Level,Result}= -{0x00:0x00:0x00,Never,Copy To R-VOL,Group,Normal End},{0x00:0x01,Never, Copy To R-VOL,Group,Normal End}, (snip) -(snip), Num.
PAGE 213
TrueCopy for Mainframe function (for IBM z/OS) Clear SIM Clear Service Information Message (SIM) operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Delete Cmd.Dev Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[TC z/OS(R)], Delete Cmd.Dev,, Normal end,,,Seq.=xxxxx [TC] TrueCopy for Mainframe function (for IBM z/OS) Delete Cmd.Dev Delete Command Device operation Normal end The operation has ended normally. Seq.
PAGE 214
TrueCopy for Mainframe function (for IBM z/OS) Delete Pair Delete Pair operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 262 (page 214).
PAGE 215
Table 263 Function Switch Operation Item Description Switch Each bit position (on/off) of the function switch information assigned by 64 bits. The beginning of the string is bit 0 and the ending of it is bit 63. "0" indicates the bit is off, and "1" indicates the bit is on. In the example above, bit 3 and bit 5 are on and the other bits are off. Resume Pair Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx,00:00,[TC],Resume Pair,,Normal end,,,Seq.
PAGE 216
Table 264 Resume Pair Operation (continued) Item Description Error Level The error level set (handling if trouble occurs) This value is output when the asynchronous pair is restored only Volume: Volume (appropriate TrueCopy for Mainframe Asynchronous pair only) Group: Group (all suspended TrueCopy for Mainframe Asynchronous pairs in the consistency group) Result The result of operation Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num.
PAGE 217
TrueCopy for Mainframe function (for IBM z/OS) Suspend Pair Suspend Pair operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 267 (page 217).
PAGE 218
38 UR for Mainframe Function Add-Pair Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[UR],Add-Pair,,Normal end,,,Seq.=xxxxxx +{P-VOL(LDKC:CU:LDEV),S-VOL(LDKC:CU:LDEV),MirrorID,S/N,CTRLID,Priority, Initial Copy, M-JNLG,R-JNLG,Path Gr.ID,Error Level,CFW,Result}=[{0x00:0x00:0x00,0x00:0x20:0x00,0x00, 65432,5,32,Entire,0x02,0x00,Default,Group,Copy to S-VOL,Normal end}, -{0x00:0x00:0x01,0x00:0x20:0x01,0x00,65432,5,32,Entire,0x02,0x00,Default,Group, Copy to S-VOL, Normal end}],Num.
PAGE 219
Clear-SIM Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[UR],Clear-SIM,,Normal end,,,Seq.=xxxxxx [UR] Universal Replicator for Mainframe function (for IBM z/OS) Clear-SIM Clear-Service Information Message (SIM) operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Delete-Pair Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx,00:00,[UR],Delete-Pair,,Normal end,,,Seq.
PAGE 220
Table 269 Delete-Pair Operation (continued) Item Description Delete Mode The delete mode Normal: Normal mode, Force: Force mode Result The result of operation Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Pairs The number of pairs Edit-EXCTG (Extended Consistency Group) Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx,00:00,[UR],Edit-EXCTG,Add,Normal end, Seq=xxxxx +{LDKC,EXCTG}={0x00,0x00} ++{LDKC,JNLG,MirrorID,S/N,CTRLID,Cmd.Dev.
PAGE 221
Table 271 Edit-EXCTG Operation (continued) Item Description CTRLID The controller ID Cmd.Dev. (LDKC:CU:LDEV) The LDKC, CU, and LDEV numbers of the remote command device Result The result of the operation Normal end: normal end, Error(xxxx-yyyyy): abnormal end xxxx: part code, yyyyy: error code Num. of EXCTGs The number of extended consistency groups for which the configuration has been changed Journal-Option Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[UR],Journal-Option,,Normal end,Seq.
PAGE 222
Table 272 Journal-Option Operation (continued) Item Description Forward Path Watch Indicates whether to transfer the path blockade watch period set to the master journal Time group to the restore journal group. Yes: Transfer, No: Do Not Transfer. Use of Cache Indicates whether to store the journal data in the restore journal group in cache. Use: Store the journal data in cache. Not Used: Store the journal data in journal volume. Speed of Line (Mbps) The transfer speed of the communication line.
PAGE 223
Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 274 (page 223). Table 274 Journal-Vol Operation Item Description LDKC The journal group's LDKC number JNLG The journal group number Timer Type The timer type.
PAGE 224
Table 276 Journal-Vol Operation (continued) Item Description Result The result of operation. Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of JNL Grps The number of journal groups. Pair-Option Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[UR],Pair-Option,,Normal end,,,Seq.
PAGE 225
[{0x00,0x01,0x01,0x00:0x12:0x34,Normal end},{0x00,0x10,0x02,0x00:0x56:0x78,Normal end}], Num. of Mirrors=2 [UR] Universal Replicator for Mainframe function (for IBM z/OS) R-Cmd.Dev. R-Cmd.Dev. operation Assign Assign is selected as the parameter. The operation uses the following parameters as shown in Table 278 (page 225). Table 278 Parameters for R-Cmd.Dev. Operation Item Description Assign The remote command device is assigned. Release The remote command device is released.
PAGE 226
Universal Replicator for Mainframe function (for IBM z/OS) Resume-Pair Resume-Pair operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Table 280 Resume-Pair Operation Item Description P-VOL(LDKC:CU:LDEV) The LDKC, CU, and LDEV numbers of the primary data volume S-VOL(LDKC:CU:LDEV) The LDKC, CU, and LDEV numbers of the secondary data volume When it is set by using a spreadsheet, N/A is output for CU and LDEV numbers.
PAGE 227
Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 281 (page 227). Table 281 Suspend-Pair Operation Item Description P-VOL(LDKC:CU:LDEV) The LDKC, CU, and LDEV numbers of the primary data volume If it is set by using a spreadsheet, N/A will be output for CU and LDEV numbers when the Type is S-VOL.
PAGE 228
Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 282 (page 228). Table 282 System-Option Operation Item Description Max Initial Copy The number of volumes you can copy at a time during an initial copy operation. LDKC:CU The LDKC and CU numbers. Change SIM Report Whether to report SIM to the host or not. Report. Not report.
PAGE 229
39 VLL Function Install CV Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[VLL],Install CV,,Normal end,,,Seq.=xxxxxx +{PG,LDKC:CU:LDEV,Start LBA,Emulation,Size,Unit,System Disk }= [{XX-XX-(X),0xXX:0xXX:0xXX, XXXXXXXX,OPEN-V,XXXXXXXX,KB,Disable}, {X-X-(X),0xXX:0xXX:0xXX,XXXXXXXX,OPEN-V,XXXXXXXX,KB,Disable}],Num. of LDEVs=2 [VLL] Virtual LVI / Virtual LUN function Install CV Install Customized Volume (CV) operation No parameter No parameter is selected in the above example.
PAGE 230
Table 284 Install CV Operation (continued) Item Description System Disk Indicates system disk status Enable: Enabled, Disable: Disabled Num. of LDEVs The number of LDEVs Make Volume Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[VLL],Make Volume,,Normal end,,,Seq.=xxxxxx +[PG,LDKC:CU:LDEV,Emulation,Size,Unit,System Disk]=[{X-X-(X),0xXX:0xXX:0xXX,OPEN-V, XXXXXXXXXXXXXXXX,KB,Disable }, {X-X-(X),0xXX:0xXX:0xXX,OPEN-V,XXXXXXXXXXXXXXXX,KB,Disable}],Num.
PAGE 231
Table 286 Make Volume Operation (continued) Item Description Unit The unit of the CV capacity. The unit varies according to the setting. KB: For open-system volume Cyl: For mainframe-system volume LBA: When LBA is specified System Disk Indicates system disk status Enable: Enabled, Disable: Disabled Num. of LDEVs The number of LDEVs Set SSID Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[VLL],Set SSID,,Normal end,,,Seq.
PAGE 232
Detailed information displays for this operation, as shown in Table 288 (page 232). Table 288 System Disk Options operation Item Description Option The name of a system disk option. Set The setting status. Disable or Enable will appear. Result The result of the operation. Normal: Normal end, Error: Abnormal end Num. of Modes The number of system disk options. Volume Initialize Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx,00:00,[VLL],Volume Initialize,,Normal end,,,Seq.
PAGE 233
Volume to Space Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[VLL],Volume to Space,,Normal end,,,Seq.=xxxxxx +{PG,LDKC:CU:LDEV}=[{XX-XX-(X),0xXX:0xXX:0xXX},{XX-XX-(X),0xXX:0xXX:0xXX}], Num. of LDEVs=2 [VLL] Virtual LVI / Virtual LUN function Volume to Space Volume to Space operation Normal end The operation has ended normally. Seq.
PAGE 234
40 XP Auto LUN Software Function Create Auto Plan Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[VM], Create Auto Plan,,Normal end,,,Seq.=xxxxx [Auto LUN] HP XP Auto LUN Software function Create Auto Plan Log Create Auto Plan Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Del Auto Plan Log Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[Auto LUN],Del Auto Plan Log,,Normal end,,,Seq.
PAGE 235
Table 292 Delete Auto Plan Operation Item Description PlanNo The executed operation. Number: is output when a part of the auto migration plans is deleted. The number indicates what number of lines from the top of the auto migration plan list and the subsequent lines were deleted. ALL: is output when all the auto migration plans are deleted. Num. of Plan The number of settings. 1 is always output. Del Migration Log Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.
PAGE 236
Table 293 Set Auto Plan Param Operation (continued) Item Description PlanType The specified sampling term. One of these values is output: • None • Every day • Once every X days (For the value of X, see PlanDay index below) • Once a week • Once a month PlanDay The setting value for sampling term. The output value depends on the sampling term output to PlanType. • If None is output to PlanType, nothing is output to PlanDay. • If Every day is output to PlanType, nothing is output to PlanDay.
PAGE 237
Table 294 Set Class Threshold Operation Item Description ClassName The class name of the HDD whose threshold is changed. The class name is displayed in the alphabet from A to J. AvailabilityMax(%) The threshold (the upper limit of the disk usage rate) after it changes. The threshold is displayed by the number from 0 to 100. The unit is percent (%). Num. of Classes The number of HDD classes whose threshold is changed. Set Fixed PG Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.
PAGE 238
Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 296 (page 238). Table 296 Set Migration Vol Operation Item Description Instruction Indicates that the manual migration plan is set or deleted; Create: Set, Delete: Deleted SourceLDEV The logical volume ID of the migration source.
PAGE 239
Table 297 Set Plan Condition Operation (continued) Item Description TimeRequiredMax(min) The specified upper limit of the migration time. The upper limit of the migration time is displayed by the number from 10 to 120. The unit is minute. AvailabilityMax(%) The specified upper limit of the disk usage rate. The upper limit of the disk usage rate is displayed by the number from 10 to 100. The unit is percent (%). VolulmeMax The specified maximum number of the volumes that are migrated in a same time.
PAGE 240
41 VRM Function Attribute Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[VRM],Attribute,,Normal end,,,Seq.=xxxxxx +{LDKC:CU:LDEV,Attribute,Result}=[{0x00:0x00:0x01,0x80,Normal end}, {0x00:0x00:0x02,0x82,Error(9205-8122),{0x00:0x00:0x03,0x81,Normal end}, {0x00:0x00:0x03,0x81,Normal end}],Num. of LDEVs=XXX [VRM] Volume Retention Manager function Attribute Attribute operation Normal end The operation has ended normally. Seq.
PAGE 241
Table 300 VTOC Operation Item Description LDKC:CU:LDEV The LDKC, CU, and LDEV numbers VTOC(Trk) The VTOC size of the specified LDEV is indicated by the number of tracks. Result The result of operation Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num.
PAGE 242
42 VSEC Function Set Group Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx,00:00,[VSEC],Set Group,,Normal end,,,Seq.
PAGE 243
Table 301 Set Group Operation (continued) Item Description LDEV Group The LDEV group name. Security The setting status of the security set to the security group. Enable, Disable Attr The attribute of the security group. Access. Access attribute, Pool: Pool attribute RsvVol Indicates whether the logical volume in the security group can be used as a secondary volume in the remote copy destination. Enable: Used as secondary volume, Disable: Not used as secondary volume Num.
PAGE 244
43 VVOL Function Add V-Vol (Snapshot) Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[VVOL],Add V-Vol (Snapshot),,Normal end,,,Seq.=xxxxx +{V-VolGroup,Capa(blocks),CLPR,Emulation,Result}={V1-1,1,4294967296,0,OPEN-V,Normal end} ++{LDKC:CU:LDEV,LDEVCapa(blocks),SSID}=[{0x00:0x00:0x00,96000},{0x00:0x00:0x01,96000}],Num. of LDEVs=2 +{V-VolGroup,Capa(blocks),CLPR,Emulation,Result}={V2-1,1,4294967296,0,OPEN-V,Normal end} ++{LDKC:CU:LDEV,LDEVCapa(blocks),SSID}=[{0x00:0x01:0x00,4294967296}],Num.
PAGE 245
Add V-Vol (THP) operation for XP Thin Provisioning Software Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 303 (page 245).
PAGE 246
Table 304 Asso V-VOL/Rel Pool Operation Item Description Command Indicates the operation executed to the XP Thin Provisioning (THP) volume. If Command is Release or Discard, the logged information indicates that the operation was only requested, but not finished . Associate: Links the Pool and the THP volume. Release: Releases the link between the Pool and the THP volume. Change: Changes the warn threshold. Discard: Discards the 0 data pages. Stop Discarding: Suspends the discarding of the 0 data pages.
PAGE 247
Delete V-Vol (THP) Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[VVOL],Delete V-Vol (THP),,Normal end,,,Seq.=xxxxx +{V-VolGroup,Result}=[{X1-1,Normal end},{X2-1,Normal end},{X3-1,Normal end}], Num. of Groups=3 [VVOL] V Volume function Delete V-Vol (THP) Delete V-Vol (THP) operation for HP XP Thin Provisioning Software Normal end The operation has ended normally. Seq.
PAGE 248
Table 307 Emulation Operation Item Description Mode Indicates the change of emulation mode. 0: Changes the emulation mode of an LDEV that a path is not defined, from Open 0V to Open V. (Normal mode). 1: Changes the emulation mode of an LDEV regardless of path definition, from Open 0V to Open V. (Forceful mode) 2: Changes the emulation mode of an LDEV that a path is not defined, from Open V to Open 0V.
PAGE 249
Pool Optimize Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx,00:00,[VVOL], Pool Optimize,,Normal end,,,Seq.=xxxxx [VVOL] V Volume function Pool Optimize Pool Optimize operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (0000000000 to 4294967295) Pool Restore Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[VVOL],Pool Restore,,Normal end,,,Seq.=xxxxx +{Pool ID, Result}=[{1,Normal end}, {2,Normal end },{2,Normal end},{128,Normal end}] Num.
PAGE 250
Detailed Information Detailed information displays for this operation, as shown in Table 310 (page 250). Table 310 Pool SIM Comp Req Operation Item Description SIM The reference code of the Service Information Message (SIM) generated in the storage system with resolved errors or service request status. No SIM reference code appears if the SIM cannot be completed due to the unsatisfied requirements. 0xXXXXXX: Reference code of the SIM Num.
PAGE 251
Set XRC Option Operation root,99,2004/12/02,17:51:17.468,+09:00,[XRC],Set XRC Option,,Normal End,,,Seq.=00020 +{CLPR,LV2THD(%),Block Option,Donot Block,LV1 Sleep,SleepTime(ms),LV1 SIM,LV2 Suspend} =[{00,50,Cache,Disable,Disable,100,Disable,Disable}, -{01,70,Cache,Enable ,Disable,10,Disable,Disable}, -{02,60,Cache,Disable,Disable, 10,Enable ,Enable }],Num. of CLPRs=32 [XRC] XRC function Set XRC Option Set XRC Option operation Normal end The operation has ended normally. Seq.
PAGE 252
44 Audit Log Information for the Commands Sent from the Host This chapter provides audit log information about the commands sent from the host. The audit logs received when you operate the host are not the history of the operations. They are the history of the commands that the storage system received from the host. FC-SP — Operation Name user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx,00:00,,FC-SP,,Normal end,from=xxxxxxxxxxxxxx,, Seq.=xxxxx FC-SP FC-SP operation Normal end The commands have ended normally.
PAGE 253
OPEN interface Accept The commands have been received from the host. from=xxxxxxxxxxxxxx WWN of the host that sent the command. When the commands are received from the storage system, the WWN of the storage system that has sent the commands is output. AP=0xXXXX The ID that is being used internally by the host which sent the command and the storage system. Seq.
PAGE 254
45 Audit Log Information about the Key Used for the Encryption License Key This chapter provides audit log information about the key used for data encryption. • “Encryption (ENC) Function — Create Enc. Key Operation” (page 254) • “Encryption (ENC) Function — Enc. Key Backup Operation” (page 254) • “Encryption (ENC) Function — Enc. Key Restore Operation” (page 254) • “Encryption (ENC) Function — PG Enc.
PAGE 255
Encryption (ENC) Function — PG Enc. Set Operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[ENC],PG Enc. Set,,Normal end,,,Seq.=xxxxx +{PG,Encryption}=[{XX-XX,Enable},{XX-XX,Disable}],Num. of PGs=2 [ENC] ENC function PG Enc. Set PG Encryption Set operation Normal end The operation has ended normally. Seq.=xxxxxx Log information serial number (0000000000 to 4294967295) Detailed Information Detailed information displays for this operation, as shown in Table 313 (page 255). Table 313 PG Enc.
PAGE 256
Detailed Information Detailed information displays for this operation, as shown in “ Delete Operation” (page 256). Table 314 Delete Operation Index Description LDKC:CU:LDEV The LDKC, CU, and LDEV numbers. Num. of LDEVs The number of set LDEVs.
PAGE 257
46 Support and Other Resources Related Documentation • HP StorageWorks XP24000/XP20000 Disk Array Owner Guide • HP StorageWorks XP24000/XP20000 LUN Manager User Guide • HP StorageWorks XP24000/XP20000 Remote Web Console User Guide You can find these documents on the HP Manuals website: http://www.hp.com/support/manuals In the Storage section, click Storage Software and then select a product.
PAGE 258
Subscription Service HP recommends that you register your product at the Subscriber’s Choice for Business website: http://www.hp.com/go/e-updates After registering, you will receive email notification of product enhancements, new driver versions, firmware updates, and other product resources. HP Websites For additional information, see the following HP websites: • http://www.hp.com • http://www.hp.com/go/storage • http://www.hp.com/support/manuals • http://www.hp.
PAGE 259
A Audit Log Information File Output by Function This appendix includes more detailed information about the audit log information file. Table 315 (page 259) lists audit log information file output for operations that are common to all Remote Web Console functions. Table 316 (page 259) lists audit log information file output for each program option button on the Remote Web Console Main window.
PAGE 260
Table 316 Output of Audit Log Information File and Operations (continued) Option Operation Launching Menu Output of Audit Log Information File Tab Operation Function Name Operation Name Add LU Path Add LU Path2 Release LU Path Delete LU Path2 LUN Security: Disable –> Enable Set Security Switch LUN Security: Enable –> Disable Set Security Switch Add New WWN Add WWN2 Delete WWN Delete WWN2 Change WWN & Name Change WWN2 Add New Host Group Add Host Group2 Delete Host Group Delete Host Grou
PAGE 261
Table 316 Output of Audit Log Information File and Operations (continued) Option Operation Launching Menu Output of Audit Log Information File Tab Operation Function Name Operation Name Set FCSP Target2, 4 Authentication (Host Group): Disable –> Enable Set FCSP Target2, 4 Authentication (Host Group): Enable –> Disable Add New Authentication Information (Host) Set FCSP Host2, 4 Change Authentication Information (Host) Set FCSP Host2, 4 Delete Authentication Information (Host) Set FCSP Host2, 4 R
PAGE 262
Table 316 Output of Audit Log Information File and Operations (continued) Option Operation Launching Menu Output of Audit Log Information File Tab Operation Function Name Operation Name Shredding Shredder Set Shredding/ End Shredding NOTE: Set Shredding is output when shredding started. End Shredding is output when shredding ended. Pool Suspend Suspend Shredding Encryption settings for ENC Parity Group PG Enc.
PAGE 263
Table 316 Output of Audit Log Information File and Operations (continued) Option Operation Launching Menu Performance Monitor Output of Audit Log Information File Tab Monitoring Options Operation Function Name Operation Name Set Cache Residency (M/F Volume) Set M/F DCR2, 4 Release Cache Residency (Open Volume) Delete Open DCR2, 4 Release Cache Residency (M/F Volume) Delete M/F DCR2, 4 Prestaging ON DCR Prestaging2, 7 CurrentStatus Enable Perf Mon Monitoring S/W Gathering Interval Monitori
PAGE 264
Table 316 Output of Audit Log Information File and Operations (continued) Option Operation Launching Menu Output of Audit Log Information File Tab WWN Operation Function Name Operation Name Set Ctrl Kind (Port Control) Set Ctrl Kind All Thresholds Set All Prio WWN2, 4 Set Priority (Prio) WWN (Attribute / Upper) Set Prio WWN2, 4 Update WWN (Perf Ctrl Name / WWN Change) Update WWN2, 4 Add WWN (WWN is added to a Perf Ctrl Group.
PAGE 265
Table 316 Output of Audit Log Information File and Operations (continued) Option Operation Launching Menu Output of Audit Log Information File Tab Quorum Disk Operation Operation Function Name Operation Name Pairsplit-r (CA) CA Pairsplit-r2 Pairsplit-r (ESAM) ESAM Pairsplit-r2 Pairresync (CA) CA Pairresync2 Pairresync (ESAM) ESAM Pairresync2 Change Pair Option CA Change Pair Option2 Add Quorum Disk ID ESAM Add Quorum Disk ID Delete Quorum Disk ID RCU Operation Asynchronous Operation
PAGE 266
Table 316 Output of Audit Log Information File and Operations (continued) Option Operation Launching Menu Output of Audit Log Information File Tab Operation Function Name Operation Name Disk Controller (DKC) Operation Add Disk Controller (DKC) RCU Add RCU Pair Operation HP XP Business Copy Change Disk Controller (DKC) Option Change RCU Option Delete Disk Controller (DKC) Delete RCU Add Path Add Path2, 4 Delete Path Delete Path2, 4 Port Change (Target, Initiator, RCU Target) PORT Change
PAGE 267
Table 316 Output of Audit Log Information File and Operations (continued) Option Operation Launching Menu Output of Audit Log Information File Tab Asynchronous Operation Script Operation Operation Function Name Operation Name Change RCU Option Change RCU Option Delete RCU Delete RCU Add Path Add Path2, 4 Delete Path Delete Path2, 4 Add SSID Add RCU Delete SSID Delete RCU Port Change (Target, Initiator, RCU Target) PORT Change Port Add Consistency Group TC Add CTG Consistency Group O
PAGE 268
Table 316 Output of Audit Log Information File and Operations (continued) Option Operation Launching Menu Output of Audit Log Information File Tab Pair Operation Optional Operation EXCTG Operation Operation Function Name Operation Name Add Path Add Path2, 4 Delete Path Delete Path2, 4 Port Change (Target, Initiator, RCU Target) PORT Change Port Add Pair UR Add-Pair2 Suspend Pair Suspend-Pair2 Resume Pair Resume-Pair2 Delete Pair Delete-Pair2 Change Pair Option Pair-Option2 Change S
PAGE 269
Table 316 Output of Audit Log Information File and Operations (continued) Option Operation Launching Menu Data Retention Output of Audit Log Information File Tab Operation Function Name Operation Name XRC XRC Option XRC Set XRC Option Data Retention Utility Attribute / S-VOL / Reserved/ Data Ret Attribute2 Mode Clear / Retention term Expiration-Lock2 Expiration-Lock HP XP External Storage Volume Operation Add Volume Ext Stor AddVolume(FIBRE)2 Delete Volume DeleteVolume(FIBRE)2 Alternat
PAGE 270
Table 316 Output of Audit Log Information File and Operations (continued) Option Operation Output of Audit Log Information File Launching Menu Tab Operation Function Name Operation Name Environmental Setting LicenseKey Install PP KEY PP Install chk2 Uninstall PP Uninstall chk2 File PP Install File chk Enable PP Enable chk Disable PP Disable chk Available Install PP Available Install Apply PP Apply SNMP Information Set SNMP Agent SNMP Set SNMP Agent Email Information Update Addre
PAGE 271
• ◦ Change 1 –> Change 2: Log information is output for the Change 2 operation. ◦ Add –> Change: Log information is output as an Add operation, but the contents of the setting are output according to the setting of the Change operation.
PAGE 272
Table 317 LUN Manager Operation and Priority of Audit Log Output (continued) Operation Change Target of Operation Priority Host Group 3 WWN 3 Host Group 3 WWN 3 Changing Host Mode 3 Command Device 4 Command Dev.
PAGE 273
B SVP Operations Output to the Audit Log File Table 318 (page 273) describes SVP operations and the operation name that is output to Audit Log File.
PAGE 274
Table 318 SVP Operations Output to the Audit Log File (continued) GUI operation SVP start button Output of Audit Log File Function Operation Function Name Operation Name Add LU Path Delete LU Path Set Speed Mode Set Host Mode Set Security Switch Add WWN Delete WWN Change WWN Add Host Group Delete Host Group Change Host Group Delete DKC WWN Force Reset Make LUSE Release LUSE DCR Configuration DCR Prestaging M/F DCR Open DCR CVS Configuration Install CV Volume to Space Make Vol./Vol.
PAGE 275
Table 318 SVP Operations Output to the Audit Log File (continued) GUI operation SVP start button Information Output of Audit Log File Function Operation Function Name Initialize ORM Value Initialize ORM Value Initialize ORM Value Setting Battery Life Setting Battery Life Set Battery Life Set Machine Install Date Set Machine Install Date Machine Install Date Log Complete Information Operation Name SIM Complete Delete Delete Log SIM Reporting Option SIM Reporting Option Threshold Value
PAGE 276
C CFL Extension Operations Output to the Audit Log Information File This appendix describes CFL Extension operations and the operation name that is output to audit log information file. See Table 319 (page 276). Table 319 CFL Extension Operations Output to the Audit Log Information File CFL Extension operations Audit Log Information File Output Command Function Name Operation Name CFL Extension CflSet Start Logs of operations performed by CFLSET command are output between CflSet Start and CflSet End.
PAGE 277
Glossary C CFL Configuration File Loader. CHA Channel adapter. A device that provides the interface between the array and the external host system. Occasionally, this term is used synonymously with the term channel host interface processor (CHIP). CLPR Cache logical partition. CM Cache memory. CPAV HP XP for Compatible Parallel Access Volumes Software. CSW Cache switch path. CT consistency CTG Consistency group. CU Control unit.
PAGE 278
M M-VOL Main volume. MCU Main control unit. MIB Management information base. A database of managed objects accessed by network management protocols. An SNMP MIB is a set of parameters that an SNMP management station can query or set in the SNMP agent of a network device (for example, a router). MU Mirror unit. N NVS Nonvolatile storage. O OND On-Demand function. P P-VOL Primary volume. PA Physical address.
PAGE 279
T T-VOL Target volume. TB Terabyte. Equivalent to 1,000 Gb for data storage and statistics, or 1,024 Gb for memory. TC TrueCopy. U UR Hitachi Universal Replicator. Also known as HP XP Continuous Access Journal (Cnt Acc-J). UT Universal Time. A modern time system related to the conventional Greenwich Mean Time (GMT) used for time zones. UUID User Definable LUN ID. UVM Universal Volume Manager. V V-VOL Virtual volume. VLL Virtual LVI / Virtual LUN. VMA Volume management area.