HP ProLiant SL170z G6 Server Maintenance and Service Guide Part number 571284-005 Fifth Edition March 2013
Legal notices © Copyright 2009, 2013 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Contents Customer Self Repair .............................................................................................................................. 5 Parts Only Warranty Service ..................................................................................................................... 5 Illustrated Parts Catalog ........................................................................................................................ 16 Mechanical Components ................................
Setup Utility Menu Bar ....................................................................................................................... 67 BIOS Update ......................................................................................................................................... 73 Clear CMOS ......................................................................................................................................... 74 Power-on Self-Test (POST) ...................................
Customer Self Repair HP products are designed with many Customer Self Repair (CSR) parts to minimize repair time and allow for greater flexibility in performing defective parts replacement. If during the diagnosis period HP (or HP service providers or service partners) identifies that the repair can be accomplished by the use of a CSR part, HP will ship that part directly to you for replacement. There are two categories of CSR parts: • Mandatory—Parts for which customer self repair is mandatory.
Réparation par le client (CSR) Les produits HP comportent de nombreuses pièces CSR (Customer Self Repair = réparation par le client) afin de minimiser les délais de réparation et faciliter le remplacement des pièces défectueuses. Si pendant la période de diagnostic, HP (ou ses partenaires ou mainteneurs agréés) détermine que la réparation peut être effectuée à l'aide d'une pièce CSR, HP vous l'envoie directement.
Riparazione da parte del cliente Per abbreviare i tempi di riparazione e garantire una maggiore flessibilità nella sostituzione di parti difettose, i prodotti HP sono realizzati con numerosi componenti che possono essere riparati direttamente dal cliente (CSR, Customer Self Repair). Se in fase di diagnostica HP (o un centro di servizi o di assistenza HP) identifica il guasto come riparabile mediante un ricambio CSR, HP lo spedirà direttamente al cliente per la sostituzione.
Customer Self Repair HP Produkte enthalten viele CSR-Teile (Customer Self Repair), um Reparaturzeiten zu minimieren und höhere Flexibilität beim Austausch defekter Bauteile zu ermöglichen. Wenn HP (oder ein HP Servicepartner) bei der Diagnose feststellt, dass das Produkt mithilfe eines CSR-Teils repariert werden kann, sendet Ihnen HP dieses Bauteil zum Austausch direkt zu.
Reparaciones del propio cliente Los productos de HP incluyen muchos componentes que el propio usuario puede reemplazar (Customer Self Repair, CSR) para minimizar el tiempo de reparación y ofrecer una mayor flexibilidad a la hora de realizar sustituciones de componentes defectuosos.
Customer Self Repair Veel onderdelen in HP producten zijn door de klant zelf te repareren, waardoor de reparatieduur tot een minimum beperkt kan blijven en de flexibiliteit in het vervangen van defecte onderdelen groter is. Deze onderdelen worden CSR-onderdelen (Customer Self Repair) genoemd.
Reparo feito pelo cliente Os produtos da HP são projetados com muitas peças para reparo feito pelo cliente (CSR) de modo a minimizar o tempo de reparo e permitir maior flexibilidade na substituição de peças com defeito. Se, durante o período de diagnóstico, a HP (ou fornecedores/parceiros de serviço da HP) concluir que o reparo pode ser efetuado pelo uso de uma peça CSR, a peça de reposição será enviada diretamente ao cliente.
Contents 12
Contents 13
Contents 14
Contents 15
Illustrated Parts Catalog Mechanical Components Item Description Spare part number Customer Self Repair 1 Top cover — Mandatory1 2 PCIe x16 riser card bracket — Mandatory1 3 1U tray for 170 system — Mandatory1 4 Fan blank kit — Mandatory1 5 Power supply blank kit — Mandatory1 Mandatory—Parts for which customer self repair is mandatory. If you request HP to replace these parts, you will be charged for the travel and labor costs of this service.
Mandatory: Obligatoire—Pièces pour lesquelles la réparation par le client est obligatoire. Si vous demandez à HP de remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous seront facturés. 1 Optional: Facultatif—Pièces pour lesquelles la réparation par le client est facultative. Ces pièces sont également conçues pour permettre au client d'effectuer lui-même la réparation.
Mandatory: Verplicht—Onderdelen waarvoor Customer Self Repair verplicht is. Als u HP verzoekt deze onderdelen te vervangen, komen de reiskosten en het arbeidsloon voor uw rekening. 1 Optional: Optioneel—Onderdelen waarvoor reparatie door de klant optioneel is. Ook deze onderdelen zijn ontworpen voor reparatie door de klant. Als u echter HP verzoekt deze onderdelen voor u te vervangen, kunnen daarvoor extra kosten in rekening worden gebracht, afhankelijk van het type garantieservice voor het product.
Contents 19
System Components Item Description Spare part number Customer Self Repair 1 System fan 576898-001 Mandatory1 2a SATA cable1 576895-001 Mandatory1 2b SATA cable 2 576895-001 Mandatory1 3 PCIe x16 riser card 536654-001 Optional2 4 Thermal sensor board 576888-001 Mandatory1 5 IPMI card 536668-001 Optional2 6 Memory modules — — DIMM 1GB PC3-10600E 501539-001 Mandatory1 DIMM 2GB PC3-10600E 501540-001 Mandatory1 DIMM 2GB PC3-10600R 501533-001 Mandatory1 DIMM 4GB PC3-10600R
Item Description Spare part number Customer Self Repair Intel X5660 6c, 2.8 GHz, 12M, 95W 586631-002 Optional2 Intel X5650 6c, 2.66 GHz, 12M, 95W 594884-001 Optional2 Intel E5640 4c, 2.66 GHz, 12M, 80W 594885-001 Optional2 Intel E5630 4c, 2.53 GHz, 12M, 80W 594886-001 Optional2 Intel E5620 4c, 2.4 GHz, 12M, 80W 594887-001 Optional2 Intel L5640 6c, 2.4 GHz, 12M, 60W 594890-001 Optional2 Intel L5630 4c, 2.13 GHz, 12M, 40W 594891-001 Optional2 Intel L5506 2.
Mandatory: Obligatoire—Pièces pour lesquelles la réparation par le client est obligatoire. Si vous demandez à HP de remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous seront facturés. 1 Optional: Facultatif—Pièces pour lesquelles la réparation par le client est facultative. Ces pièces sont également conçues pour permettre au client d'effectuer lui-même la réparation.
Mandatory: Verplicht—Onderdelen waarvoor Customer Self Repair verplicht is. Als u HP verzoekt deze onderdelen te vervangen, komen de reiskosten en het arbeidsloon voor uw rekening. 1 Optional: Optioneel—Onderdelen waarvoor reparatie door de klant optioneel is. Ook deze onderdelen zijn ontworpen voor reparatie door de klant. Als u echter HP verzoekt deze onderdelen voor u te vervangen, kunnen daarvoor extra kosten in rekening worden gebracht, afhankelijk van het type garantieservice voor het product.
Contents 24
HP Contact Information For United States and worldwide contact information, see the Contact HP website at http://hp.com/go/assistance. In the United States: • To contact HP by phone, call 1-800-334-5144. For continuous quality improvement, calls may be recorded or monitored. • If you have purchased a Care Pack (service upgrade), see the Support & Drivers website at http://www8.hp.com/us/en/support-drivers.html. If the problem cannot be resolved at the website, call 1-800-633-3600.
Removal and Replacement Procedures This chapter provides subassembly/module-level removal and replacement procedures for the HP ProLiant SL170z G6 server. Review the specifications of a new component before installing it to make sure it is compatible with the server. When you integrate new components into the system, record its model and serial number, and any other pertinent information for future reference.
Pre-installation Procedure Perform the steps below before you open the server or before you remove or replace any component. WARNING: Failure to properly turn off the server before you open the server or before your start installing/removing components may cause serious damage as well as bodily harm. 1. Turn off the server and all the peripherals connected to it. 2.
CAUTION: Do not operate the server for long periods with the access panel open or removed. Operating the server in this manner results in improper airflow and improper cooling that can lead to thermal damage. CAUTION: The following rack-mount instructions shall be paid attention to. • Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient.
This symbol indicates that the component exceeds the recommended weight for one individual to handle safely. WARNING: To reduce the risk of personal injury or damage to the equipment, observe local occupational health and safety requirements and guidelines for manual material handling. These symbols, on power supplies or systems, indicate that the equipment is supplied by multiple sources of power.
Figure 1 Removing the top cover To reinstall the top cover: 1. Align the top cover to the chassis and then slide it towards the front panel to position it into place. 2. Install the two rear screws to secure the top cover to the chassis. Figure 2 Reinstalling the top cover Cable Management Always follow good cable management practices when working inside the computer. • • Keep cables away from major heat sources like the heatsink.
• • • • Do not sharply bend any cable. A sharp bend can break the internal wires. Never bend a SATA data cable tighter than a 30 mm (1.18 in) radius. Never crease a SATA data cable. Do not rely on components like the drive cage, power supply, or system cover to push cables down into the chassis. To remove the power supply cables from the system board connectors: 1. Squeeze on the top of the retaining latch attached to the cable end of the connector. 2.
Cable Connections The following table provides the system board designators that various cables plug into. For more detailed information about system board components, see system board components.
Hard Drives The server standard configuration can accommodate (12) 3.5-inch SATA hard disk drives, 6 in each tray or (12) 2.5-inch SATA hard disk drives, 6 in each tray. An HBA controller is required to support a (16) 2.5-inch SAS or SATA drives, 8 in each tray or (12) 3.5-inch SAS or SATA drives, 6 in each tray. NOTE: Connect hard drives 1 – 6 to ports 0 – 5 on the system board.
Figure 5 Installing the hard drive assembly To remove hard drive assembly: 1. Slide the HDD Latches to unlock the HDD Handle. 2. Raise the HDD handle. 3. Lift the HDD from the tray. 4. Lower the HDD handle. 5. Lock the HDD carrier latches.
System Board Configuration Processor HP ProLiant SL170z G6 Server, with two 170 system boards, supports four-processor operation. With two processors installed, each 170 server supports boot functions through the processor installed in processor socket 1. However, if processor 1 fails, the system automatically boots from processor 2 and provides a processor failure message. The processor socket supports Quad-Core Intel Nehalem 5500 Series processor and Intel Xeon 5600 Series processor.
3. Lift the heatsink away from the system board. CAUTION: Place heatsink down in an upright position with the thermal patch facing upward. Do not let the thermal patch touch the work surface. Figure 8 Removing the heatsink IMPORTANT: If the heatsink has been removed for any reason on a previously installed processor, it is critical that you apply more thermal interface material to the integrated heat spreader on the processor to ensure proper thermal bonding between the processor and the heatsink.
Figure 10 Removing the processor 3. Carefully rotate the tool, and then push in and release the tabs to secure the processor in the tool. Figure 11 Securing the processor CAUTION: To avoid damage to the processor, do not touch the bottom of the processor, especially the contact area. CAUTION: The pins of the socket are very fragile. Do not bend or damage them. CAUTION: Place the processor on a static-dissipating work surface or in an anti-static bag.
To install the new processor: 1. Carefully insert the processor into the processor installation tool. Handle the processor by the edges only, and do not touch the bottom of the processor, especially the contact area.
2. Be sure the tool is oriented correctly. Align the processor installation tool with the socket, and then install the processor. THE PINS ON THE SYSTEM BOARD ARE VERY FRAGILE AND EASILY DAMAGED. Figure 13 Installing the processor CAUTION: THE PINS ON THE SYSTEM BOARD ARE VERY FRAGILE AND EASILY DAMAGED. To avoid damage to the system board: • Never install or remove a processor without using the processor installation tool. • Do not touch the processor socket contacts.
3. Press and hold the tabs on the processor installation tool to separate it from the processor, and then remove the tool. Figure 14 Removing the processor installation tool 4. Close the processor socket retaining bracket and the processor locking lever. CAUTION: Be sure to close the processor socket retaining bracket before closing the processor locking lever. The lever should close without resistance. Forcing the lever closed can damage the processor and socket, requiring system board replacement.
CAUTION: To allow heatsink to draw as much heat as possible from the processor base, there must be good contact between the heatsink base and the top of the processor. To ensure good contact, you must apply thermal interface material. To apply the thermal grease compound: 1. Use the alcohol pads provided in the spare part kit or a clean cloth dipped in rubbing alcohol to clean the contact surface on the heatsink and on the new processor.
Figure 17 Installing the heatsink Memory HP ProLiant SL170z G6 server has thirty-two DIMM slots that support up to 256 GB maximum system memory. You must adhere to the following guidelines when adding or replacing memory modules: • • • For 4P system, both physical processors in each 170 server must be of the same type and speed. Use 800/1066/1333 MHz Registered/Unbuffered ECC DDR3 Memory.
• Supported configurations: ○ One DIMM per processor: 8A for CPU1; 8A for CPU2. ○ Three DIMMs per processor: 8A, 5B, 2C for CPU1; 8A, 5B, 2C for processor 2. ○ Six DIMMs per processor: 8A, 7D, 5B, 4E, 2C, 1F for CPU1; 8A, 7D, 5B, 4E, 2C, 1F for processor 2 ○ DIMM population order processor socket 1: 8A, 5B, 2C, 7D, 4E, 1F, 6G, 3H. ○ DIMM population order processor socket 2: 8A, 5B, 2C, 7D, 4E, 1F, 6G, 3H.
Figure 20 Removing a memory module CAUTION: Place the memory module on a static-dissipating work surface or inside of an anti-static bag. To install a memory module: 1. Align the notch on the bottom edge of the module with the keyed surface of the DIMM slot and then press the module fully into the slot. 2. Firmly press the holding clips inward to secure the memory module in place. Figure 21 Installing a memory module CAUTION: The memory slots are structured to ensure proper installation.
PCI Expansion Cards System Board PCI Expansion Slots There is one PCIe Gen2 x16 riser card slot on the system board.
To remove the PCIe bracket: 1. Remove one screw which secures PCIe bracket to the rear panel. 2. Pull the PCIe bracket up and away from the main board. Figure 24 Removing the PCIe bracket To remove the riser card: Remove the two screws securing the riser card to the PCIe bracket. Figure 25 Removing the PCIe x16 riser card To install the PCIe x16 riser card on the bracket: 1. Align the riser card with the bracket. 2. Fasten the two screws to secure the riser card to the bracket.
Figure 26 Installing a riser card To install the riser card with the bracket into the system board: 1. Align the riser card connector with the slot on the system board and then insert the assembly into the slot. 2. Fasten the screw to secure the bracket to the chassis. Figure 27 Installing the PCIe bracket To remove the PCIe card: 1. Remove the screw that secures the PCIe card. 2. Open the PCIe latch. 3. Pull the PCIe card back and away from the PCIe riser card. 4.
Figure 28 Removing the PCIe card To install the PCIe card: 1. Open the PCIe latch. 2. Remove PCIe card or blank. 3. Push the PCIe card into riser card connector. 4. Close PCIe latch. 5. Install screws.
IPMI Card To remove the IPMI card: 1. Unfasten the screws mounting the IPMI card. 2. Unplug the IPMI module vertically to release it from the connector. 3. Unfasten the screw to separate the IPMI card. 4. Reinstall the IPMI bracket back to the tray and secure it with screws. Figure 30 Removing the IPMI card To install the IPMI card: 1. Unfasten the screws on the front panel and remove the IPMI bracket from the tray. 2. Unfasten the screw to separate the IPMI card and its bracket. 3.
System Battery The server uses nonvolatile memory that requires 2 batteries to retain system information when power is removed. This 3-volt lithium coin cell battery is located on the system board. Figure 32 System battery location WARNING: Note the following reminders when replacing the system battery: • Replace the battery with the same type as the battery recommended by HP. Use of another battery may present a risk of fire or explosion.
Figure 33 Replacing the battery System Board Removal and Replacement Procedure To remove the system board: 1. Press the tray latch to release the tray handle. 2. Rotate the tray handle to disengage the power connector. 3. Pull the tray assembly out of the chassis. Figure 34 Removing the tray assembly 4. Remove the six screws that secure the system boards to the tray. 5. Release the system boards from the tray.
Figure 35 Removing the system board To replace the system board: 1. Put the system boards on the tray. The six screw holes on the tray should align with the system board. 2. Fasten the six screws on the system boards to secure the system boards to the tray. Figure 36 Installing the system board 3. Push the tray assembly into the tray bay until it stops. 4. Rotate the tray handle until the tray latch catches.
Figure 37 Installing the tray assembly NOTE: After the system board is replaced, reset specific BIOS settings including the system serial number using the Setup Utilities procedures on page 63. Power Supply Unit (PSU) Located on the rear panel of the server power supply is a standard auto ranging 750 watt PSU with PFC (power factor correction) function.
To install the power supply: 1. Remove the power supply blank out of the power cage. 2. Align the power supply cage connector with the open slot of power supply. 3. Slide the power supply into the power supply bay until it snaps into place. Figure 39 Removing the power blank Figure 40 Installing the power supply To remove the power supply: 1. Press the red colored handle. 2. Slide the power supply out of the power supply bay. 3.
Figure 41 Removing the power supply System Fan The server has four system fans located on the chassis’ rears fan cage. The figure below identifies the system fans by their device number and shows their corresponding cable connections.
To remove the system fan: 1. Disconnect the fan cable from its corresponding board connector. 2. Lift the system fan away from the chassis. Figure 43 Removing the system fan To replace the system fan: 1. Insert the system fan into the fan bracket. 2. Connect the fan cable to its corresponding board connector.
Connectors, Switches, and LEDs This chapter contains illustrations and tables identifying and describing the connectors, switches, buttons, and LED indicators located on the front panel, rear panel, system board and hard drives of the HP ProLiant SL170z G6. Connectors and Components Front Panel Components Figure 45 Front panel components of a two-170-server system Item Description 1a Tray handle 1b Tray latch 2 PCI blank 3 UID LED/SW 4 Power button 5 USB 2.
Rear Panel Components Figure 46 Rear panel components of a two-170-server system Item Description 1 RJ45 port 2 Power supply 2 3 Power supply 1 4 UID LED Contents 58
System Board Components Figure 47 System board components Item Designator Description 1 J44 Top: serial port Bottom: VGA port 2 CN1 Top: serial port A Bottom: VGA port 3 SW4 UID LED/SW 4 CR6 Health LED 5 SW3 Power LED/SW 6 J41 GbE LAN ports 7 J48 USB 2.0 ports 8 J49 IPMI port 9 CR1~CR9 Diagnostic LEDs 10 J32 SATA 0 connector J9 SATA 1 connector J18 SATA 2 connector J19 SATA 3 connector J22 SATA 4 connector J25 SATA 5 connector 11 XBT1 Battery 12 J38 USB 2.
Item Designator Description 14 XU1 Processor 1 socket 15 J36 Power connector 16 J42 RPS connector 17 J1~J8 DDR3 DIMM slots 18 XU2 Processor 2 socket 19 J45 Protected RTC jumper 20 J24 Riser connector 21 J57 TPM connector CAUTION: The TPM is not a customer-removable part. Any attempt to remove an installed TPM from the system board breaks or disfigures the TPM security rivet.
Front Panel LED Indicators This section contains illustration and descriptions of internal and external status LED indicators located on the front panel. These LED indicators aid in problem diagnosis by indicating the status of system components and operations of the server. The front panel LED indicators allow constant monitoring of basic system functions while the server is operating. Power LED Indicator The power status of the server is indicated by the bicolor LED on the front panel.
Health LED Indicator Figure 49 Health LED Indicator Location Table 6 Health LED indicator status Component Status Description Health LED indicator Red Critical system failure detected Amber System degraded Green System is on and no failure detected Off System is off and no failure prior to system power off Contents 62
UID LED Indicator Figure 50 the UID LED Indicator locations Table 7 UID LED indicator states Component Status Description UID LED indicator Blue Identification Flashing blue System is being remotely managed Contents 63
LAN Port LED Indicator The LAN port on the front panel has two LED indicators that allow monitoring of network activity. Figure 51 the LAN/LED indicator locations Table 8 LAN/LED indicator status Item Component Status Description 1 LAN activity status LED indicator Flashing green Ongoing network data activity. Off No network data activity or no connection. Steady green The LAN connection is using a GbE link. Steady green The LAN connection is using 10Mbps/100 Mbps link. Off No connection.
Diagnostic Tools and Setup Utilities This chapter provides an overview of the Power-on Self-Test (POST), the POST error messages, and BIOS, SAS and SATA setup utilities. BIOS Software The server uses BIOS to boot up the system. BIOS software is a ROM-based firmware that allows reliability, manageability, and connectivity for server platforms. This software contains a set of programs permanently stored in an EEPROM chipset located on the system board.
Navigating through the Setup Utility Use the keys listed in the legend bar on the right of the Setup screen to navigate through the various menu and submenu screens of the Setup Utility. Table 9 lists these legend keys and their respective functions. Table 9 Setup Utility Navigation Keys Key Function ← and → To move between selections on the menu bar. ↑ and ↓ To move the cursor to the field you want. The currently selected field is highlighted.
Figure 52 Setup Utility General Help screen Press F1 to get the general help message box. Setup Utility Menu Bar The BIOS Setup Utility provides a menu bar with the menu selections. The menu bar choices are described in the topics below.
Figure 54 Main menu of BIOS Setup Utility 2 Use this menu to set the system time and date, and configure of the following items: • • • • • • • • View BIOS build date and version. View CPU type / CPU speed /CPU physical count information. View System memory size. View System serial number. View MAC address for the embedded NIC. Set Server Asset Tag. Set system time and date. Set boot features: ○ ○ ○ ○ ○ Enable or Disable POST Speed up. Enable or Disable Splash Screen. Enable or Disable Bootup Num-Lock.
Advanced Menu Figure 55 Advanced menu of the BIOS Setup Utility WARNING: Incorrect settings may cause the server to malfunction. To correct the settings, press F9 key to restore the default settings. • • • • • • • • • CPU Configuration – Configure and view the current CPU configuration and settings. IDE Configuration – Use this screen to select options for the IDE Configuration Settings. I/O Device Configuration – Configure the serial port settings of the server.
Figure 56 IPMI Configuration menu of the BIOS Setup Utility • • • • SEL Configuration – Configuration of the BMC System Event Log. • Hardware health information – Select to get information about CPU temperature, ambient temperature, rear HDD Opt fan speed and system fan speed. Serial Port Configuration – Select to configure system serial ports. LAN Configuration – Select for LAN configuration. Watchdog Configuration – Select to configure POST Watchdog Timer Action and BMC Watch Dog Time Out.
Figure 58 Security menu of the BIOS Setup Utility 2 Use this menu to configure the following items: • • Administrator Password --- Display if an administrator password is Set or Not. Change Admin Password --- Allows you to access and change all settings in the Setup Utility. The administrator password allows you to configure access for system users.
To set a new administrator password: 1. In the Security screen, select a set password field - Change Admin Password, and then press Enter. 2. Type a new password in the Enter New Password box. 3. Retype the password to verify the first entry, and then press Enter. 4. Press F10 to close the Setup Utility. 5. After setting the password, Setup automatically sets the password check to Setup. Boot Menu Figure 59 Boot menu of the BIOS Setup Utility Use this menu to configure the boot settings.
Exit Menu Figure 60 Exit menu of the BIOS Setup Utility Use this menu to save changes or discard changes. When you save and exit, the server reboots. • Save Changes and Exit --- Save the changes you have made and exit the BIOS Setup Utility. (You can also press F10 key.) • Discard Changes and Exit --- Exit the BIOS Setup Utility without saving the changes you have made. (You can also press Esc key.) • • Discard Changes --- Discard any changes you have made. (You can also press F7 key.
Clear CMOS You may need to clear the Setup configuration values (CMOS) if the configuration has been corrupted, or if incorrect settings made in the Setup Utility have caused error messages to be unreadable. To clear CMOS: 1. Perform the Pre-installation Procedure. 2. If necessary, remove any accessory boards or cables that prevent access to the system configuration switch. 3. Locate the system configuration button (SW2) on the system board. 4. Press the button. AC power must not be connected. 5.
POST Errors Message Definition Whenever a non-fatal error occurs during POST, an error message describing the problem appears onscreen. These error messages are displayed in normal video (white text on black background), and show the details of the error. The following is an example of a POST error message: 012 --- CMOS Date/Time not set Table 10 POST Error Messages lists the most common POST error messages with corresponding troubleshooting recommendation.
Table 10 POST Error Messages Error Code Error Message Description/Corrective Action 010h Floppy Controller Failure The floppy controller initialized failed, the devices could not use normally 012h CMOS Date/Time Not Set The CMOS Date and/or Time are invalid. This error can be resolved by readjusting the system time in the Setup Utility. 048h Password check failed Password is incorrect after retried a few times. Users might need to reset the password.
Table 10 POST Error Messages Error Code Error Message Description/Corrective Action 607h System Fan 4 Missing If system fan4 is not installed or failed, system will announce this message and system will shutdown in minutes. 608h Fan Solution Not Sufficient! Critical Failure Detected - System Shutting Down in xx seconds! If one or more fans are missing, this message will appear with 'system fan x missing' together. 609h Temperature Violation Detected! Waiting 5 minutes for system to cool.
POST Related Troubleshooting Perform the following procedures when POST fails to run, displays error messages, or emits beep codes. If the POST failure is during a routine boot up, check the following: • • • All external cables and power cables should be firmly plugged in. • • • • • • The monitor's contrast and brightness settings are correct. • • All internal cabling and connections are in their proper order. The power outlet to the server should be connected and works correctly.
Physical and Operating Specifications This chapter provides physical and operating specifications for the HP ProLiant SL170z G6 server. System Unit Table 11 Hardware Specifications Item Components Processor socket Intel 1366pin FCLGA Processor support Quad-Core Intel Nehalem 5500 Series processor Intel Xeon 5600 Series processor Chipset Intel Tylersburg 36D/Intel ICH10R Hardware monitoring device IPMI 2.
Table 11 Hardware Specifications Item Components Status LED indicators Front panel • Power/system health status • UID status • • • • • System board NIC activity LAN activity LAN link status Power/system health status UID status • Auxiliary power indicators Power supply unit (PSU) 750W redundant, PSU support Thermal solution Four 80mm system fans Table 12 Physical Dimensions Item Description System board dimension 17.935’’x6.5’’ Server dimensions Rack 448W X87.5H X 735.
Table 13 Environmental Specifications Item Description Thermal output (maximum operating) 392 W/hr Acoustic emissions LWad: 6.7 Bels Normal configuration (operating at room temperature) LWad: 6.7 Bels (idle at room temperature) Table 14 Hot-Plug Power Supply Specifications Item Description Dimensions (H x W x D) 38.48 mm x 86.36 mm x 190.52 mm Weight (approximate) 1.
Documentation Feedback HP is committed to providing documentation that meets your needs. To help us improve the documentation, send any errors, suggestions, or comments to Documentation Feedback (mailto:docsfeedback@hp.com). Include the document title and part number, version number, or the URL when submitting your feedback.
Index memory, 42 A PCI expansion cards, 45 AC power power supply unit, 53 power-down procedures, 29 processor, 35 B references, 26 battery system battery, 50 replacement warnings, 50 system fan, 55 BIOS Setup Utility accessing, 65 additional navigation keys, 66 menu bar, 65 top cover, 29 Hardware configuration tools, 26 hardware specifications I/O ports, 79 BIOS software LAN controller, 79 Overview, 65 memory, 79 C power supply unit, 80 cable management, 30 processor socket, 79 CSR (c
installing, 49 Power-On Self Test removing, 49 POST error indicators, 74 POST related troubleshooting, 78 L LAN controller, 79 LED indicators recoverable POST errors, 75 processor applying thermal grease, 41 Power/system health, 61 installing, 38 M Memory module spare part number, 20 memory controller, 79 memory modules guidelines for installation, 42 installing, 44 removing, 43 O removing, 36 Processor heatsink spare part number, 21 processor socket specification, 79 Processors spare part number,
system LEDs.
