HP ProLiant DL145 Generation 3 Server Software Configuration Guide
Index 53
Index
3
32 Bit I/O setting, 8
32-Bit Memory Hole setting, 11
A
administrator password, 20;
changing, 21; definition, 20;
removing, 22; resetting, 22;
setting, 21
After Power Failure setting, 10
B
Base I/O Address setting, 16
baseboard management controller.
See BMC
Basic Input/Output System. See BIOS
configuration
Baud Rate setting, 16
beep codes, 27
BIOS configuration: access Setup, 5;
BIOS overview, 5; PhoenixBIOS
Setup Utility, 5; PhoenixBIOS
software, 5; POST, 25;
reprogramming, 32
BIOS POST Watchdog setting, 18
BMC, 51; configuring through the
serial port, 51; configuring through
the Setup Utility, 51; firmware
version, 17; selecting the IPMI LAN
interface through Setup, 18; setting
the Default Gateway field, 18;
setting the IP Address Assignment
field, 18; setting the IP Address
field, 18; setting the IP Subnet
Mask field, 18; setting the LAN
Controller field, 18; setting the
Serial port Mode field, 16
BMC Firmware Version setting, 17
Boot Diagnostic Screen setting, 9
Boot Options setting, 7
Boot Summary Screen setting, 9
boot-time diagnostic screen:
information display, 24; viewing,
24
Build Date setting, 7
C
Clear System Event Log setting, 19
CMOS RAM: clearing, 25;
definition, 5; resetting, 25
Com Port Address setting, 16
Console connection setting, 17
console redirection, 16, 17, 18
Console Type setting, 16
Continue C. R. after POST setting, 17
crisis recovery jumper, 32
D
Dedicated NIC MAC Address
setting, 10
Default Gateway setting, 18
Diagnostics Boot Mode setting, 11
DRAM Bank Interleave setting, 11
E
Embedded Broadcom BCM5715
setting, 12
Embedded NIC MAC Address
setting, 10
Embedded SATA setting, 15
Enable Master setting, 13, 15
Enable/Disable Int13 support setting,
15
Enabling Console Redirection, 52
Error Message Handling setting, 10
ESCD: clearing configuration data,
10; definition, 10
Existing Event Log number, 19
Extended Memory setting, 8
Extended Memory Testing setting, 9
Extended System Configuration Data.
See ESCD
F
factory boot mode setting, 11
Factory Boot Mode setting, 11
Flow Control setting, 16
G
General Help window, 6
H
Halt On Error setting, 10
hardware configuration: boot-time
diagnostic screen, 24
high-precision event timer setting.
See HPET Timer
HPET Timer setting, 11
I
Intelligent Platform Management
Interface. See IPMI
Interrupt setting, 16
IP Address Assignment setting, 18
IP Address setting, 18
IP Subnet Mask setting, 18
IPMI, 17
IPMI Specification Version setting, 17
Item Specific Help panel, 6
L
LAN Controller setting, 18
Latency Timer setting, 13, 15
LBA Mode Control setting, 8
legend bar, 6
Log POST errors setting, 19
M
MAC address, 10
Media Access Control. See MAC
address, See MAC address
menu bar, 7
Microsoft Windows NOS: caution
before installation, 15, 34;
installation procedure, 34;
supported versions, 33
Multi-Sector Transfers setting, 8
N
network operating system. See NOS
Node Interleave setting, 11
NOS, 33
NOS installation: hardware
reminders, 33; Microsoft Windows
NOS, 34; NOS support, 33; pre-
installation procedure, 33; Red Hat
Enterprise Linux NOS, 39; Sun
Solaris 10, 46; SUSE Linux
Enterprise Server NOS, 43
NumLock setting, 9
O
Option ROM Expansion setting, 12
Option ROM Scan, embedded
Broadcom setting, 14
Option ROM Scan, PCI device
setting, 13
Option ROM Scan, SATA setting, 15
P
PCI Device, Slot # setting, 12
PhoenixBIOS Setup Utility: "Run
Setup" message, 5; accessing, 5;
additional navigation keys, 6;
administrator password, 20;
Advanced menu, 10; Boot menu,
22; Boot Options submenu, 9;
Boot-time diagnostic screen, 24;
clearing the CMOS RAM, 25;
closing, 23; CMOS RAM, 5;
Console Redirection submenu, 16;
Embedded Broadcom BCM5715