HP Superdome 2 Partitioning Administrator Guide

1/2/7 00/08 03/00 103C/402F ----/----/11 Bridge Device - PCI/PCI bridge
1/2/7 00/0D 00/00 103C/3306 103C/3309/04 Base System Peripherals - Other syste
1/2/7 00/0D 00/02 103C/3307 103C/3309/04 Base System Peripherals - Other syste
1/2/7 00/0D 00/04 103C/3300 103C/3309/01 Serial Bus Controllers - USB
6/2/2 6C/00 02/00 103C/402F ----/----/11 Bridge Device - PCI/PCI bridge
6/2/3 6A/00 02/00 103C/402F ----/----/11 Bridge Device - PCI/PCI bridge
6/2/4 6A/00 00/00 103C/402F ----/----/11 Bridge Device - PCI/PCI bridge
6/2/5 6B/00 00/00 103C/402F ----/----/11 Bridge Device - PCI/PCI bridge
6/2/6 6B/00 02/00 103C/402F ----/----/11 Bridge Device - PCI/PCI bridge
Fast initialization: Enabled
Getting MAC Addresses for Ignite-UX
The EFI command lanaddress can be used to list the MAC addresses of every network interface
in a partition:
Shell> lanaddress
LAN Address Information
LAN Address Path
----------------- ----------------------------------------
M 001 Mac(002655A9F352) PcieRoot(0x0)/Pci(0x0,0x0)/Pci(0x0,0x0)/MAC(002655A9F352,0x0)
002 Mac(002655A9F356) PcieRoot(0x0)/Pci(0x0,0x0)/Pci(0x0,0x1)/MAC(002655A9F356,0x0)
M 003 Mac(002655A9F35A) PcieRoot(0x0)/Pci(0x2,0x0)/Pci(0x0,0x0)/MAC(002655A9F35A,0x0)
004 Mac(002655A9F35E) PcieRoot(0x0)/Pci(0x2,0x0)/Pci(0x0,0x1)/MAC(002655A9F35E,0x0)
NOTE: The first four addresses, each of which have a path of the form
PcieRoot()/Pci()/Pci()/MAC() are LAN on Motherboard modules directly on a blade.
Task Summaries for Rebooting and Resetting Partitions
Table 6-1 describes the main nPartition boot and reset tasks and provides brief summaries and
references for detailed procedures.
You can perform the nPartition boot tasks in Table 6-1 “nPartition Boot and Reset Task
Summaries” using either the OA CLI or the OA GUI.
Table 6-1 nPartition Boot and Reset Task Summaries
SummaryTask
Boots the partition. See “POWERON PARTITION”.POWERON (pe)
1
Shuts down the partition. See “POWEROFF PARTITION”.POWEROFF (pe)
Reboots the OS on the specified nPartition or virtual partition. See
“REBOOT PARTITION”.
REBOOT (rs)
Connect or disconnect the DVD module to the specified partition. See
“SET PARTITION DVD”.
SET PARTITION DVD
Performs a transfer-of-control reset of the specified nPartition or virtual
partition. See “Force System Reset and Crash Dump (TOC) PARTITION”.
TOC (tc)
Displays the version of the firmware bundle currently installed on the
server blades within the specified partition(s). See “UPDATE SHOW
NPARTITION”.
UPDATE SHOW
Displays information about the DVD drive attached to the specified
partition. See “SHOW PARTITION DVD”.
SHOW PARTITION DVD
Displays information about the specified partition(s). See “SHOW
PARTITION INFO”.
SHOW PARTITION INFO
54 Booting and Resetting Partitions (nPartitions and vPars)