HP Location Discovery Services Installation Instructions

HP Location Discovery Services
Installation Instructions
Translated versions
To view, select a language:
• English (http://www.hp.com/support/LDS_II_en)
• Français (http://www.hp.com/support/LDS_II_fr)
• Italiano (http://www.hp.com/support/LDS_II_it)
• Español (http://www.hp.com/support/LDS_II_sp)
• Deutsch (http://www.hp.com/support/LDS_II_gr)
• (http://www.hp.com/support/LDS_II_jp)
• (http://www.hp.com/support/LDS_II_sc)
Overview
HP provides built-in location awareness in the new ProLiant servers, a
capability that works hand-in-hand with technology in the new HP
Intelligent Series racks. Together these technologies provide the rack
identification number and precise U location of the servers. This
information is communicated through Systems Insight Manager (SIM),
Insight Control Power Management (ICPM), and HP iPDUs.
For Location Discovery Services (LDS) software requirements, see the
QuickSpecs on the HP website
(http://www.hp.com/go/rackandpower).
Kit contents
Kit Modules
HP 14U Location Discovery Kit Two modules (two 7U modules)
HP 22U Location Discovery Kit Three modules (two 7U modules
and one 8U module)
HP 36U Location Discovery Kit Five modules (four 7U modules
and one 8U module)
HP 42U Location Discovery Kit Six modules (six 7U modules)
HP 47U Location Discovery Kit Six modules (one 7U module and
five 8U modules)
Precautions
WARNING: A risk of personal injury or damage to the
equipment exists. Before installing the LDS modules in a
populated rack, be sure that the rack is stabilized in
accordance with all product and rack warnings. When
installing the modules, you must partially extend one or
more rack mounted devices (up to 8U of devices) at a time.
Only single devices that are mounted on slide rails are
intended to be fully extended from the rack and remain in
a safe and upright position.
To reduce the risk of personal injury, damage to the
equipment, or rack instability:
• Do not extend more devices than necessary to install a
single 7U or 8U module. To prevent the rack from
becoming unstable, do not extend any device more
than 9 cm (3.5 in) from the rack.
• If a device is mounted on non-slide, static rails and it
must be extended more than 9 cm (3.5 in), remove the
device completely from the rack. For more information
about removing the device from the rack, see the
device installation instructions.
• If a device is secured to the rack and not mounted on
rails, remove the device completely from the rack.
For more information about extending devices from the
rack, see Best Practices for HP Intelligent Series Rack
Family on the HP website
(http://www.hp.com/go/infrastructure).
IMPORTANT: The modules must be installed in the correct
numerical order. The order number is listed on the
installation label, and the U location is listed on the pull
tab.
Installing the modules
1. If there is a front-mounted device installed in the rack, extend the
device to allow for module installation. If there is a blanking
panel installed in the rack, remove the panel.
For instructions on extending the device, see the specific device
user guide.
For safety precautions, see "Precautions (on page 1)".
© Copyright 2012 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The only
warranties for HP products and services are set forth in the express warranty
statements accompanying such products and services. Nothing herein should
be construed as constituting an additional warranty. HP shall not be liable for
technical or editorial errors or omissions contained herein.
Bluetooth® is a trademark owned by its proprietor and used by
Hewlett-Packard Company under license.
Part Number: 691495-001
May 2012
Edition: 1
*691495-001*
691495-001