HP Integrated Lights-Out Addendum

Settings (parameters) found on the Encryption page of the iLO
user interface.
Parameter Default
value
Description
Current
cipher
— Displays the current cipher for this
web browser session. Upon logging
into the iLO using the web browser,
the browser and the iLO negotiate
the cipher setting to be used for the
session. This web page displays the
negotiated cipher.
Enforce
AES/3DES
Encryption
— This setting allows you to enable or
disable AES/3DES encryption.
• If disabled, AES/3DES
encryption is not used.
• If enabled, cipher strength must
be at least AES or 3DES to
connect to iLO.
HPONCFG supported operating systems
HPONCFG is supported on:
• Windows® 2000 Server
• Windows Server™ 2003
• Red Hat Linux Enterprise Linux 3
• Red Hat Linux Enterprise Linux 4
• Red Hat Linux Enterprise Linux 5
• United Linux 1.0
• SUSE LINUX Enterprise Server 8
• SUSE LINUX Enterprise Server 9
• SUSE LINUX Enterprise Server 10
HPONCFG Linux server installation
HPONCFG is installed when the ProLiant support pack is installed.
You can download the rpm of HPONCFG for Linux distributions from
the HP website
(http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareD
escription.jsp?lang=en&cc=us&prodTypeId=18964&prodSeriesId=1
146658&prodNameId=1135772&swEnvOID=2025&swLang=8&m
ode=2&taskId=135&swItem=MTX-
34ea4dc35e034dce8d26be2d30).
The following is a list of supported HPONCFG rpm files and the
Linux distributions they support.
RPM supported Distribution
hponcfg-1.6.0-
1.linux.rpm
Red Hat Enterprise Linux 3
hponcfg-1.6.0-
1.linux.rpm
Red Hat Enterprise Linux 4
hponcfg-1.6.0-
1.linux.rpm
Red Hat Enterprise Linux 5
hponcfg-1.6.0-
1.linux.rpm
SUSE Linux Enterprise Server 8/ United
Linux 1.0
hponcfg-1.6.0-
1.linux.rpm
SUSE Linux Enterprise Server 9
RPM supported Distribution
hponcfg-1.6.0-
1.linux.rpm
SUSE Linux Enterprise Server 10
Install the appropriate package using the RPM installation utility. As
an example for package installation, you can install the hponcfg
RPM on Red Hat Enterprise Linux 3 using the following:
rpm -ivh hponcfg-1.6.0-1.linux.rpm
If an older version of the hponcfg RPM package is installed on the
system, run the following command to remove the older version
before installing the new version of HPONCFG:
rpm –e hponcfg
The hprsm RPM package or hp-ilo RPM package must be installed on
the system before installing the hponcfg RPM package.
After installation, the HPONCFG executable is located in the /sbin
directory. Be sure that the appropriate Management Interface Driver
is installed. See the section, "HPONCFG requirements" for details
about where to obtain this driver and file.
iLO settings CLI commands
The iLO settings commands enable you to view or modify iLO
settings. iLO settings are located at /map1/config1.
Targets
No targets
Properties
Property Access Description
oemhp_enable
Read/Write Enables or disables
the iLO. Boolean
values are accepted.
oemhp_timeout
Read/Write Sets session timeout
in minutes. Valid
values are 15, 30,
60, and 120.
oemhp_passthrough
Read/Write Enables or disables
Terminal Services
Passthrough. Boolean
values are accepted.
oemhp_rbsuenable
Read/Write Enables or disables
RBSU prompt during
POST. Boolean
values are accepted.
oemhp_rbsulogin
Read/Write Enables or disables
login requirement for
accessing RBSU.
Boolean values are
accepted.
oemhp_rbsushowip
Read/Write Enables or disables
iLO IP address
display during POST.
Boolean values are
accepted.
oemhp_rcconfig
Read/Write Sets the Remote
Console
configuration. Valid
values are enabled,
disabled, or
automatic.