HP iLO 3 Scripting and Command Line Guide

When using the iLO Shared Network Port, flashing the iLO firmware through the XML interface
takes approximately 7 minutes to complete. Flashing the firmware using Shared Network Port with
iLO does not take any longer to complete than using the dedicated iLO management port.
REG_DDNS_SERVER VALUE instructs iLO to register the management port with a DDNS server.
The possible values are Yes or No.
SPEED_AUTOSELECT is a Boolean parameter to enable or disable the iLO transceiver to auto-detect
the speed (NIC_SPEED) and duplex (FULL_DUPLEX) of the network. This parameter is optional, and
the Boolean string must be set to Yes to enable the speed auto-detect. If this parameter is used,
the Boolean string value must not be left blank. The possible values are Yes or No. The parameter
value is case insensitive.
NIC_SPEED is used to set the transceiver speed if SPEED_AUTOSELECT is set to No. The possible
values are 10, 100, or Automatic. If SPEED_AUTOSELECT is set to N, and NIC_SPEED is set to
Automatic, the current value is retained. In other words, if SPEED_AUTOSELECT is set to N, then
Automatic is not an applicable value for NIC_SPEED.
FULL_DUPLEX is used to decide if iLO is to support full-duplex or half-duplex mode. It is only
applicable if SPEED_AUTOSELECT was set to No. The possible values are Yes, No, or Automatic.
If SPEED_AUTOSELECT is set to N, and FULL_DUPLEX is set to Automatic, the current value is
retained. In other words, if SPEED_AUTOSELECT is set to N, then Automatic is not an applicable
value for FULL_DUPLEX. The parameter value is case insensitive.
DHCP_ENABLE is used to enable DHCP. The possible values are Yes or No. The parameter value
is case insensitive.
IP_ADDRESS is used to select the IP address for iLO if DHCP is not enabled. If an empty string is
entered, the current value is deleted.
SUBNET_MASK is used to select the subnet mask for iLO if DHCP is not enabled. If an empty string
is entered, the current value is deleted.
GATEWAY_IP_ADDRESS is used to select the default gateway IP address for iLO if DHCP is not
enabled. If an empty string is entered, the current value is deleted.
DNS_NAME is used to specify the DNS name for iLO. If an empty string is entered, the current
value is deleted.
DOMAIN_NAME is used to specify the domain name for the network where iLO resides. If an
empty string is entered, the current value is deleted.
DHCP_GATEWAY specifies if the DHCP-assigned gateway address is to be used. The possible
values are Yes or No. The parameter value is case sensitive. This selection is only valid if DHCP
is enabled.
DHCP_DNS_SERVER specifies if the DHCP-assigned DNS server is to be used. The possible values
are Yes or No. The parameter value is case sensitive. This selection is only valid if DHCP is enabled.
DHCP_WINS_SERVER specifies if the DHCP-assigned WINS server is to be used. The possible
values are Yes or No. The parameter value is case sensitive. This selection is only valid if DHCP
is enabled.
DHCP_STATIC_ROUTE specifies if the DHCP-assigned static routes are to be used. The possible
values are Yes or No. The parameter value is case sensitive. This selection is only valid if DHCP
is enabled.
REG_WINS_SERVER specifies if iLO must be registered with the WINS server. The possible values
are Yes or No. The parameter value is case sensitive. This selection is only valid if DHCP is enabled.
PRIM_DNS_SERVER specifies the IP address of the primary DNS server. This parameter is only
relevant if the DHCP-assigned DNS server address feature is disabled. If an empty string is entered,
the current value is deleted.
RIB_INFO 81