HP Integrated Lights-Out 2 Management Processor Scripting and Command Line Resource Guide

DHCP_ENABLE – Used to enable DHCP. The possible values are Yes or No. It is case insensitive.
IP_ADDRESS – Used to select the IP address for the iLO 2 if DHCP is not enabled. If an empty string
is entered, the current value is deleted.
SUBNET_MASK – Used to select the subnet mask for the iLO 2 if DHCP is not enabled. If an empty
string is entered, the current value is deleted.
GATEWAY_IP_ADDRESS – Used to select the default gateway IP address for the iLO 2 if DHCP is
not enabled. If an empty string is entered, the current value is deleted.
DNS_NAME – Used to specify the DNS name for the iLO 2. If an empty string is entered, the
current value is deleted.
DOMAIN_NAME – Used to specify the domain name for the network where the iLO 2 resides. If
an empty string is entered, the current value is deleted.
DHCP_GATEWAY – Specifies if the DHCP-assigned gateway address is to be used. The possible
values are Yes or No. It is case sensitive. This selection is only valid if DHCP is enabled.
DHCP_DNS_SERVER – Specifies if the DHCP-assigned DNS server is to be used. The possible
values are Yes or No. It is case sensitive. This selection is only valid if DHCP is enabled.
DHCP_WINS_SERVER – Specifies if the DHCP-assigned WINS server is to be used. The possible
values are Yes or No. It is case sensitive. This selection is only valid if DHCP is enabled.
DHCP_STATIC_ROUTE – Specifies if the DHCP-assigned static routes are to be used. The possible
values are Yes or No. It is case sensitive. This selection is only valid if DHCP is enabled.
REG_WINS_SERVER – Specifies if the iLO 2 must be register with the WINS server. The possible
values are Yes or No. It is case sensitive. This selection is only valid if DHCP is enabled.
PRIM_DNS_SERVER – Specifies the IP address of the primary DNS server. This parameter is only
relevant if the DHCP-assigned DNS server address feature is disabled. If an empty string is entered,
the current value is deleted.
SEC_DNS_SERVER – Specifies the IP address of the secondary DNS server. This parameter is only
relevant if the DHCP-assigned DNS server address feature is disabled. If an empty string is entered,
the current value is deleted.
TER_DNS_SERVER – Specifies the IP address of the tertiary DNS server. This parameter is only
relevant if the DHCP-assigned DNS server address feature is disabled. If an empty string is entered,
the current value is deleted.
PRIM_WINS_SERVER – Specifies the IP address of the primary WINS server. This parameter is
only relevant if the DHCP-assigned WINS server address feature is disabled. If an empty string is
entered, the current value is deleted.
SEC_WINS_SERVER specifies the IP address of the secondary WINS server. This parameter is only
relevant if the DHCP-assigned WINS server address feature is disabled. If an empty string is entered,
the current value is deleted.
STATIC_ROUTE_1, STATIC_ROUTE_2, and STATIC_ROUTE_3 – Used to specify the destination
and gateway IP addresses of the static routes. The following two parameters are used within the
static route commands. If an empty string is entered, the current value is deleted.
• DEST – Specifies the destination IP addresses of the static route. This parameter is only relevant
if the DHCP-assigned static route feature is disabled. If an empty string is entered, the current
value is deleted.
• GATEWAY – Specifies the gateway IP addresses of the static route. This parameter is only
relevant if the DHCP-assigned static route feature is disabled. If an empty string is entered,
the current value is deleted.
WEB_AGENT_IP_ADDRESS – Specifies the address for the Web-enabled agents. If an empty string
is entered, the current value is deleted.
RIB_INFO 89