A.05.80 HP Insight Remote Support Advanced Managed Systems Configuration Guide (June 2013)
Table Of Contents
- Managed Systems Configuration Guide
- Contents
- About This Document
- Insight Remote Support Advanced Managed Systems Overview
- ProLiant Windows Server Configuration
- ProLiant Linux Server Configuration
- ProLiant VMware ESX Server Configuration
- ProLiant VMware ESXi Server Configuration
- Proliant Citrix Server Configuration
- ProLiant c-Class BladeSystem Enclosure Configuration
- Integrity Windows 2003 Server Configuration
- Integrity Windows 2008 Server Configuration
- Integrity Linux Server Configuration
- Integrity Superdome 2 Server Configuration
- HP-UX Server Configuration
- Meeting HP-UX Operating System, Software, and Patch Requirements
- More About WBEM and SFM with Insight Remote Support
- Verifying System Fault Management is Operational
- Creating WBEM Users
- Configuring WEBES to Support WBEM Indications
- Firewall and Port Requirements for HP-UX Managed Systems
- Configuring HP-UX Managed Systems for Proactive Collection Services
- OpenVMS Server Configuration
- Tru64 UNIX Server Configuration
- NonStop Server Configuration
- Enterprise Virtual Array Configuration
- Understanding the Different Server Types and Software Applications
- Command View EVA 8.0.1 and Higher Hosted on the CMS
- Important Port Settings Information
- Important Information Regarding New HP SIM Installations
- Correcting an Existing HP SIM Installation
- Change the WMI Mapper Proxy port in the HP SIM User Interface on the CMS
- Restore Defaults to the wbemportlist.xml file
- Installing and Configuring Command View EVA After HP SIM
- Resetting the Port Numbers when Command View EVA was Installed before HP SIM
- Command View EVA Hosted on a Separate SMS
- Requirements and Documentation to Configure Command View EVA on the SMS
- Overview of Command View EVA 7.0.1 through 8.0.1 with SMI-S Requirements
- SMS System and Access Requirements
- WEBES – EVA Communication
- HP SIM – EVA Communication
- Software Required on the SMS
- Fulfilling ELMC Common Requirements for a Windows SMS
- Installing MC3 on the SMS
- Configuring EVA-Specific Information on the CMS
- Requirements to Support EVA4400 and P6000 with Command View EVA on the ABM
- Enabling User-Initiated Service Mode in Command View EVA 9.3
- Performing a Remote Service Test in Command View EVA 9.3
- Troubleshooting EVA Managed Systems
- P4000 Storage Systems Migration Procedure
- Network Storage System Configuration
- Modular Smart Array Configuration
- Tape Library Configuration
- System Requirements
- Managed Systems Configuration
- Nearline (Tape Library) Configuration
- Secure Key Manager Configuration
- StoreOnce D2D (Disk-to-Disk) Backup System Configuration
- Enterprise Systems Library G3 Configuration
- TapeAssure Service Configuration
- Prerequisites
- Command View for Tape Libraries and TapeAssure Service Installation
- Configure the Command View TL 2.8 CIMOM and TapeAssure Provider
- Configure the Command View TL 3.0 CIMOM and TapeAssure Provider
- HP SIM Device Discovery
- WEBES Configuration
- Create a New SMI-S Protocol in WEBES
- Subscribe to the Command View TL and TapeAssure CIMOM
- SAN Switch Configuration
- E-Series Switch Configuration
- A-Series Switch Configuration
- UPS Network Module Configuration
- Modular Cooling System Configuration
- Glossary
- Index
Chapter 14
Tru64 UNIX Server Configuration
Before you can monitor your Tru64 UNIX managed systems you must:
l Verify the managed systems are supported by checking the Insight Remote Support Advanced
Release Notes.
l Verify ELMC for Tru64 is installed and configured.
ELMC System Requirements
Tru64 UNIX managed systems must meet the following requirements before ELMC is installed. In
clusters, minimum requirements apply to each node in the cluster.
Hardware and Software Requirements
l Processor architecture: HP AlphaServer
l Operating system: Tru64 UNIX version 4.0F, 4.0G, 5.1A or higher
Note: HP Sustaining Engineering maintains a schedule of support for the Tru64 UNIX operating
system. HP does not commit to supporting WEBES when installed on an operating system
version that has exceeded its end-of-support date.
l Minimum 20 MB free disk space for installation of all components.
l TCP/IP services must be installed and running.
l Upgrade to V1.22 or higher of the Emulex (EMX) driver if you have an EMX LP6000, LP7000, or
LP8000 adapter (KGPSA–xx) using the SLI2 programming interface. Use of an EMX driver prior to
V1.22 may result in data not being processed correctly.
l System firmware: The prerequisite system firmware supports the logging of events according to the
FRU Table Version 5 Specification, which is required for WEBES FRU configuration tree processing.
n All DSxx and ES40 systems must have firmware V5.7–4 or higher.
n All other systems (currently ES45, GSxx, and TS202c) ship with a firmware version that is already
compatible with WEBES processing.
In general, users should take advantage of the latest improvements by obtaining the most recent
firmware version available for their platform.
Required Permissions and Access
To install, upgrade, or uninstall WEBES, you must be logged on as the root user. The
/usr/opt/hp/svctools directory is owned by root, and has rwx (read, write, and execute)
permissions for root (owner), and no permissions for any other user (group or world).
HP Insight Remote Support Advanced (A.05.80)Page 97 of 204