A.05.80 HP Insight Remote Support Advanced Managed Systems Configuration Guide (June 2013)
Table Of Contents
- Managed Systems Configuration Guide
- Contents
- About This Document
- Insight Remote Support Advanced Managed Systems Overview
- ProLiant Windows Server Configuration
- ProLiant Linux Server Configuration
- ProLiant VMware ESX Server Configuration
- ProLiant VMware ESXi Server Configuration
- Proliant Citrix Server Configuration
- ProLiant c-Class BladeSystem Enclosure Configuration
- Integrity Windows 2003 Server Configuration
- Integrity Windows 2008 Server Configuration
- Integrity Linux Server Configuration
- Integrity Superdome 2 Server Configuration
- HP-UX Server Configuration
- Meeting HP-UX Operating System, Software, and Patch Requirements
- More About WBEM and SFM with Insight Remote Support
- Verifying System Fault Management is Operational
- Creating WBEM Users
- Configuring WEBES to Support WBEM Indications
- Firewall and Port Requirements for HP-UX Managed Systems
- Configuring HP-UX Managed Systems for Proactive Collection Services
- OpenVMS Server Configuration
- Tru64 UNIX Server Configuration
- NonStop Server Configuration
- Enterprise Virtual Array Configuration
- Understanding the Different Server Types and Software Applications
- Command View EVA 8.0.1 and Higher Hosted on the CMS
- Important Port Settings Information
- Important Information Regarding New HP SIM Installations
- Correcting an Existing HP SIM Installation
- Change the WMI Mapper Proxy port in the HP SIM User Interface on the CMS
- Restore Defaults to the wbemportlist.xml file
- Installing and Configuring Command View EVA After HP SIM
- Resetting the Port Numbers when Command View EVA was Installed before HP SIM
- Command View EVA Hosted on a Separate SMS
- Requirements and Documentation to Configure Command View EVA on the SMS
- Overview of Command View EVA 7.0.1 through 8.0.1 with SMI-S Requirements
- SMS System and Access Requirements
- WEBES – EVA Communication
- HP SIM – EVA Communication
- Software Required on the SMS
- Fulfilling ELMC Common Requirements for a Windows SMS
- Installing MC3 on the SMS
- Configuring EVA-Specific Information on the CMS
- Requirements to Support EVA4400 and P6000 with Command View EVA on the ABM
- Enabling User-Initiated Service Mode in Command View EVA 9.3
- Performing a Remote Service Test in Command View EVA 9.3
- Troubleshooting EVA Managed Systems
- P4000 Storage Systems Migration Procedure
- Network Storage System Configuration
- Modular Smart Array Configuration
- Tape Library Configuration
- System Requirements
- Managed Systems Configuration
- Nearline (Tape Library) Configuration
- Secure Key Manager Configuration
- StoreOnce D2D (Disk-to-Disk) Backup System Configuration
- Enterprise Systems Library G3 Configuration
- TapeAssure Service Configuration
- Prerequisites
- Command View for Tape Libraries and TapeAssure Service Installation
- Configure the Command View TL 2.8 CIMOM and TapeAssure Provider
- Configure the Command View TL 3.0 CIMOM and TapeAssure Provider
- HP SIM Device Discovery
- WEBES Configuration
- Create a New SMI-S Protocol in WEBES
- Subscribe to the Command View TL and TapeAssure CIMOM
- SAN Switch Configuration
- E-Series Switch Configuration
- A-Series Switch Configuration
- UPS Network Module Configuration
- Modular Cooling System Configuration
- Glossary
- Index
Managed Systems Configuration Guide
Chapter 12: HP-UX Server Configuration
Installing the Advanced Configuration Collector
Note: The SMH prerequisites should have already been installed at this point.
The Advanced Configuration Collector (RS-ACC) component enables the Remote Support Configuration
Collector to gather configuration data from your eligible HP-UX managed systems. The RS-ACC
component for HP-UX servers is available on the CMS through the HP Remote Support Software
Manager (RSSWM). This component must be distributed and installed to your HP-UX managed systems.
Note: If you are not covered under a Mission Critical support contract, you do not need to install the
RS-ACC component.
The RS-ACC software is distributed as a SD-UX serial depot compressed in a gzip file. RSSWM
delivers the files to one of the following default locations on the CMS:
Note: This directory is configurable when Insight Remote Support Advanced is installed.
c:\Hewlett-Packard\BusinessSupport\UC\ACC-HPUX\
Or
c:\Program Files[(x86)]\SWMAgent\Installers\UC\ACC-HPUX
Or
c:\Program Files\HP\SWMAgent\Installers\UC\ACC\HPUX
For Insight Remote Support Advanced, the following files are available:
l PA-RISC Depot:
rs-acc-hpux-11.x-PA-A.05.80.xxx.depot.gz
l Itanium Depot:
rs-acc-hpux-11.x-IA-A.05.80.xxx.depot.gz
Choose the appropriate file for your managed system's processor type and transfer it accordingly.
Note: It is beyond the scope of this guide to describe all possible methods you can use to distribute
this file to your HP-UX managed systems, as individual customer environments vary. However, it
may be as simple as logging on to the CMS and using FTP to transport the file to a temporary location
on the managed system(s). The procedure below uses FTP.
Use the following procedure to copy and install the RS-ACC software bundle to your HP-UX managed
system:
1. Change to the directory where the RS-ACC bundle was saved (note that this directory may be
different on your environment):
# cd C:\Hewlett-Packard\BusinessSupport\UC\ACC\HPUX
HP Insight Remote Support Advanced (A.05.80)Page 85 of 204