A.05.80 HP Insight Remote Support Advanced Managed Systems Configuration Guide (June 2013)
Table Of Contents
- Managed Systems Configuration Guide
- Contents
- About This Document
- Insight Remote Support Advanced Managed Systems Overview
- ProLiant Windows Server Configuration
- ProLiant Linux Server Configuration
- ProLiant VMware ESX Server Configuration
- ProLiant VMware ESXi Server Configuration
- Proliant Citrix Server Configuration
- ProLiant c-Class BladeSystem Enclosure Configuration
- Integrity Windows 2003 Server Configuration
- Integrity Windows 2008 Server Configuration
- Integrity Linux Server Configuration
- Integrity Superdome 2 Server Configuration
- HP-UX Server Configuration
- Meeting HP-UX Operating System, Software, and Patch Requirements
- More About WBEM and SFM with Insight Remote Support
- Verifying System Fault Management is Operational
- Creating WBEM Users
- Configuring WEBES to Support WBEM Indications
- Firewall and Port Requirements for HP-UX Managed Systems
- Configuring HP-UX Managed Systems for Proactive Collection Services
- OpenVMS Server Configuration
- Tru64 UNIX Server Configuration
- NonStop Server Configuration
- Enterprise Virtual Array Configuration
- Understanding the Different Server Types and Software Applications
- Command View EVA 8.0.1 and Higher Hosted on the CMS
- Important Port Settings Information
- Important Information Regarding New HP SIM Installations
- Correcting an Existing HP SIM Installation
- Change the WMI Mapper Proxy port in the HP SIM User Interface on the CMS
- Restore Defaults to the wbemportlist.xml file
- Installing and Configuring Command View EVA After HP SIM
- Resetting the Port Numbers when Command View EVA was Installed before HP SIM
- Command View EVA Hosted on a Separate SMS
- Requirements and Documentation to Configure Command View EVA on the SMS
- Overview of Command View EVA 7.0.1 through 8.0.1 with SMI-S Requirements
- SMS System and Access Requirements
- WEBES – EVA Communication
- HP SIM – EVA Communication
- Software Required on the SMS
- Fulfilling ELMC Common Requirements for a Windows SMS
- Installing MC3 on the SMS
- Configuring EVA-Specific Information on the CMS
- Requirements to Support EVA4400 and P6000 with Command View EVA on the ABM
- Enabling User-Initiated Service Mode in Command View EVA 9.3
- Performing a Remote Service Test in Command View EVA 9.3
- Troubleshooting EVA Managed Systems
- P4000 Storage Systems Migration Procedure
- Network Storage System Configuration
- Modular Smart Array Configuration
- Tape Library Configuration
- System Requirements
- Managed Systems Configuration
- Nearline (Tape Library) Configuration
- Secure Key Manager Configuration
- StoreOnce D2D (Disk-to-Disk) Backup System Configuration
- Enterprise Systems Library G3 Configuration
- TapeAssure Service Configuration
- Prerequisites
- Command View for Tape Libraries and TapeAssure Service Installation
- Configure the Command View TL 2.8 CIMOM and TapeAssure Provider
- Configure the Command View TL 3.0 CIMOM and TapeAssure Provider
- HP SIM Device Discovery
- WEBES Configuration
- Create a New SMI-S Protocol in WEBES
- Subscribe to the Command View TL and TapeAssure CIMOM
- SAN Switch Configuration
- E-Series Switch Configuration
- A-Series Switch Configuration
- UPS Network Module Configuration
- Modular Cooling System Configuration
- Glossary
- Index
Chapter 12
HP-UX Server Configuration
This chapter describes the required state of your HP-UX managed system to make it eligible for Insight
Remote Support Advanced. Read this chapter before attempting to configure Insight Remote Support
Advanced for your HP-UX managed system.
1. Verify Hardware Support
As product support may change outside of a major software release, check the Insight Remote
Support Advanced Release Notes to verify your hardware is currently supported.
2. Verify Operating System, Software and Patch Requirements are met.
See "Meeting HP-UX Operating System, Software, and Patch Requirements" on the next page for
more information about the requirements for your particular HP-UX Operating System.
3. Establish Communication and Configure Protocols
System Fault Manager (SFM) is an Insight Remote Support Advanced communications requirement
on all supported versions of HP-UX. SFM has many patch prerequisites, and those are detailed in the
"Meeting HP-UX Operating System, Software, and Patch Requirements" on the next page. If your
system(s) already meet the minimum requirements identified in that section, then you do not need to
remove or reinstall those components. If your system(s) is not at the minimum, upgrade as directed in
"More About WBEM and SFM with Insight Remote Support" on page 77.
Note: You may be familiar with the variety of SFM providers available in the different SFM
offerings. Insight Remote Support only requires the providers in the standard SFM package(s) as
specified in "Meeting HP-UX Operating System, Software, and Patch Requirements" on the next
page.
4. Install and Configure the Advanced Configuration Collector
The Advanced Configuration Collector (RS-ACC) component generates and sends proactive service
configuration collections to HP. If you are not covered under a Mission Critical support contract, you
do not need to install or configure the RS-ACC component. If you are covered under Mission Critical
support, follow the instructions in "Installing the Advanced Configuration Collector" on page 85.
5. Complete the CMS Configuration
This chapter describes the requirements for your HP-UX managed systems. Once your managed
systems actually meet all necessary requirements, configure the CMS to communicate with the
managed system. Those processes are covered in the HP Insight Remote Support Advanced Central
Management Server Configuration Guide.
Important: When you are configuring Insight Remote Support Advanced on the Central
Management Server (CMS), configure the WBEM credentials for your HP-UX managed systems
in the HP SIM interface. This process is detailed in the second chapter of the HP Insight Remote
Support Advanced Central Management Server Configuration Guide. Take note of these
credentials as you will need to provide them later.
HP Insight Remote Support Advanced (A.05.80)Page 69 of 204