A.05.80 HP Insight Remote Support Advanced Managed Systems Configuration Guide (June 2013)
Table Of Contents
- Managed Systems Configuration Guide
- Contents
- About This Document
- Insight Remote Support Advanced Managed Systems Overview
- ProLiant Windows Server Configuration
- ProLiant Linux Server Configuration
- ProLiant VMware ESX Server Configuration
- ProLiant VMware ESXi Server Configuration
- Proliant Citrix Server Configuration
- ProLiant c-Class BladeSystem Enclosure Configuration
- Integrity Windows 2003 Server Configuration
- Integrity Windows 2008 Server Configuration
- Integrity Linux Server Configuration
- Integrity Superdome 2 Server Configuration
- HP-UX Server Configuration
- Meeting HP-UX Operating System, Software, and Patch Requirements
- More About WBEM and SFM with Insight Remote Support
- Verifying System Fault Management is Operational
- Creating WBEM Users
- Configuring WEBES to Support WBEM Indications
- Firewall and Port Requirements for HP-UX Managed Systems
- Configuring HP-UX Managed Systems for Proactive Collection Services
- OpenVMS Server Configuration
- Tru64 UNIX Server Configuration
- NonStop Server Configuration
- Enterprise Virtual Array Configuration
- Understanding the Different Server Types and Software Applications
- Command View EVA 8.0.1 and Higher Hosted on the CMS
- Important Port Settings Information
- Important Information Regarding New HP SIM Installations
- Correcting an Existing HP SIM Installation
- Change the WMI Mapper Proxy port in the HP SIM User Interface on the CMS
- Restore Defaults to the wbemportlist.xml file
- Installing and Configuring Command View EVA After HP SIM
- Resetting the Port Numbers when Command View EVA was Installed before HP SIM
- Command View EVA Hosted on a Separate SMS
- Requirements and Documentation to Configure Command View EVA on the SMS
- Overview of Command View EVA 7.0.1 through 8.0.1 with SMI-S Requirements
- SMS System and Access Requirements
- WEBES – EVA Communication
- HP SIM – EVA Communication
- Software Required on the SMS
- Fulfilling ELMC Common Requirements for a Windows SMS
- Installing MC3 on the SMS
- Configuring EVA-Specific Information on the CMS
- Requirements to Support EVA4400 and P6000 with Command View EVA on the ABM
- Enabling User-Initiated Service Mode in Command View EVA 9.3
- Performing a Remote Service Test in Command View EVA 9.3
- Troubleshooting EVA Managed Systems
- P4000 Storage Systems Migration Procedure
- Network Storage System Configuration
- Modular Smart Array Configuration
- Tape Library Configuration
- System Requirements
- Managed Systems Configuration
- Nearline (Tape Library) Configuration
- Secure Key Manager Configuration
- StoreOnce D2D (Disk-to-Disk) Backup System Configuration
- Enterprise Systems Library G3 Configuration
- TapeAssure Service Configuration
- Prerequisites
- Command View for Tape Libraries and TapeAssure Service Installation
- Configure the Command View TL 2.8 CIMOM and TapeAssure Provider
- Configure the Command View TL 3.0 CIMOM and TapeAssure Provider
- HP SIM Device Discovery
- WEBES Configuration
- Create a New SMI-S Protocol in WEBES
- Subscribe to the Command View TL and TapeAssure CIMOM
- SAN Switch Configuration
- E-Series Switch Configuration
- A-Series Switch Configuration
- UPS Network Module Configuration
- Modular Cooling System Configuration
- Glossary
- Index
Managed Systems Configuration Guide
Chapter 21: SAN Switch Configuration
HA-MIB (yes, y, no, n): [yes] yes
FCIP-MIB (yes, y, no, n): [no]
ISCSI-MIB (yes, y, no, n): [no]
SW-TRAP (yes, y, no, n): [yes]
swFCPortScn (yes, y, no, n): [no] yes
swEventTrap (yes, y, no, n): [no] yes
swFabricWatchTrap (yes, y, no, n): [no] yes
swTrackChangesTrap (yes, y, no, n): [no] yes
FA-TRAP (yes, y, no, n): [yes]
connUnitStatusChange (yes, y, no, n): [no] yes
connUnitEventTrap (yes, y, no, n): [no] yes
connUnitSensorStatusChange (yes, y, no, n): [no] yes
connUnitPortStatusChange (yes, y, no, n): [no] yes
SW-EXTTRAP (yes, y, no, n): [no] yes
9. Display the IP address of the switch, so it can be added to HP SIM:
> ipaddrshow
SWITCH Ethernet IP Address: 1.2.3.4
Ethernet Subnetmask: 1.2.3.4
Fibre Channel IP Address: none
Fibre Channel Subnetmask: none
Gateway IP Address: 1.2.3.4
DHCP: Off
10. Modify the switch systemgroup variables if required:
> snmpconfig --set systemGroup
Customizing MIB-II system variables ... At each prompt, do one of the fo
llowing:
o to accept current value,
o enter the appropriate new value,
o to skip the rest of configuration, or
o to cancel any change.
To correct any input mistake: erases the previous character, erases the
whole line,
sysDescr: [Fibre Channel Switch.] Brocade 4/16 FC Switch
sysLocation: [End User Premise.] HP Building 11th floor
sysContact: [Field Support.] John Doe
authTrapsEnabled (true, t, false, f): [true]
Committing configuration...done.
11. Load and compile the Brocade MIBs in HP SIM. Brocade MIBs are available from the HP website.
The Brocade Fabric OS V6.1.0 MIB package contains 15 MIBs. A detailed description of the MIBs is
available in the Brocade Fabric OS MIB Reference document.
HP SIM comes with a number of precompiled MIBs. The compiled MIBs have a file extension of
.cfg.
n View the list of MIBs on the HP SIM server:
> dir c:\program files\hp\systems insight manager\MIBs\ *.MIB
HP Insight Remote Support Advanced (A.05.80)Page 182 of 204