A.05.80 HP Insight Remote Support Advanced Managed Systems Configuration Guide (June 2013)
Table Of Contents
- Managed Systems Configuration Guide
- Contents
- About This Document
- Insight Remote Support Advanced Managed Systems Overview
- ProLiant Windows Server Configuration
- ProLiant Linux Server Configuration
- ProLiant VMware ESX Server Configuration
- ProLiant VMware ESXi Server Configuration
- Proliant Citrix Server Configuration
- ProLiant c-Class BladeSystem Enclosure Configuration
- Integrity Windows 2003 Server Configuration
- Integrity Windows 2008 Server Configuration
- Integrity Linux Server Configuration
- Integrity Superdome 2 Server Configuration
- HP-UX Server Configuration
- Meeting HP-UX Operating System, Software, and Patch Requirements
- More About WBEM and SFM with Insight Remote Support
- Verifying System Fault Management is Operational
- Creating WBEM Users
- Configuring WEBES to Support WBEM Indications
- Firewall and Port Requirements for HP-UX Managed Systems
- Configuring HP-UX Managed Systems for Proactive Collection Services
- OpenVMS Server Configuration
- Tru64 UNIX Server Configuration
- NonStop Server Configuration
- Enterprise Virtual Array Configuration
- Understanding the Different Server Types and Software Applications
- Command View EVA 8.0.1 and Higher Hosted on the CMS
- Important Port Settings Information
- Important Information Regarding New HP SIM Installations
- Correcting an Existing HP SIM Installation
- Change the WMI Mapper Proxy port in the HP SIM User Interface on the CMS
- Restore Defaults to the wbemportlist.xml file
- Installing and Configuring Command View EVA After HP SIM
- Resetting the Port Numbers when Command View EVA was Installed before HP SIM
- Command View EVA Hosted on a Separate SMS
- Requirements and Documentation to Configure Command View EVA on the SMS
- Overview of Command View EVA 7.0.1 through 8.0.1 with SMI-S Requirements
- SMS System and Access Requirements
- WEBES – EVA Communication
- HP SIM – EVA Communication
- Software Required on the SMS
- Fulfilling ELMC Common Requirements for a Windows SMS
- Installing MC3 on the SMS
- Configuring EVA-Specific Information on the CMS
- Requirements to Support EVA4400 and P6000 with Command View EVA on the ABM
- Enabling User-Initiated Service Mode in Command View EVA 9.3
- Performing a Remote Service Test in Command View EVA 9.3
- Troubleshooting EVA Managed Systems
- P4000 Storage Systems Migration Procedure
- Network Storage System Configuration
- Modular Smart Array Configuration
- Tape Library Configuration
- System Requirements
- Managed Systems Configuration
- Nearline (Tape Library) Configuration
- Secure Key Manager Configuration
- StoreOnce D2D (Disk-to-Disk) Backup System Configuration
- Enterprise Systems Library G3 Configuration
- TapeAssure Service Configuration
- Prerequisites
- Command View for Tape Libraries and TapeAssure Service Installation
- Configure the Command View TL 2.8 CIMOM and TapeAssure Provider
- Configure the Command View TL 3.0 CIMOM and TapeAssure Provider
- HP SIM Device Discovery
- WEBES Configuration
- Create a New SMI-S Protocol in WEBES
- Subscribe to the Command View TL and TapeAssure CIMOM
- SAN Switch Configuration
- E-Series Switch Configuration
- A-Series Switch Configuration
- UPS Network Module Configuration
- Modular Cooling System Configuration
- Glossary
- Index
Chapter 20
Tape Library Configuration
System Requirements
l WEBES is required on the CMS for Nearline Tape Library support and supported virtual and physical
libraries. Because you must install WEBES on the CMS before you can complete the Tape Library
configurations, revisit this chapter after you fully configure your CMS.
l All managed systems must be configured to send SNMP v1 traps to the CMS.
Managed Systems Configuration
Each Virtual and Physical Library System must be discovered and recognized by HP SIM on the CMS.
Configuration Details
Be careful to:
l Verify every tape library in the customer environment is recognized by HP SIM. Do not forget to
configure the tape library application to send traps to the CMS.
l Verify the correct product number and serial number for the tape library has been captured by HP SIM.
l Modify any incorrect or missing contract identifiers and customer contact details in HP SIM.
l Verify the most appropriate system type is selected for the managed system.
Note: Incidents are not raised for tape libraries unless they are recognized by HP SIM.
Nearline (Tape Library) Configuration
Tape library configuration uses HP Command View for Tape Libraries (TL) management tools.
Enterprise Systems Library E-series and Enterprise
Modular Library Configuration
To support your Enterprise Systems Library (ESL) E-series and Enterprise Modular Library (EML) Tape
Libraries, you need to configure SNMP in Command View for Tape Libraries (TL).
Use the following procedure to configure SNMP on your ESL E-series and EML Tape Libraries:
1. Log on to the Command View TL web interface for each ESL E-series or EML.
2. Click the Configuration tab.
3. In the left panel, select SNMP Alerts. The current SNMP traps appear in the right panel.
HP Insight Remote Support Advanced (A.05.80)Page 169 of 204