HP Insight Management Agents Installation Guide Part number: 333513-006 Sixth edition: March 2010
Legal notices © Copyright 2010 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Confidential computer software.
Contents 1 HP Insight Management Agents overview Introduction ................................................................................................................................................ 4 Insight Management Agents ......................................................................................................................... 4 HP Systems Insight Manager ........................................................................................................................
1 HP Insight Management Agents overview Introduction HP Insight Management Agents deliver multisystem access to all key system administration tools for predictive fault management, access to critical system information, and integration with partner management solutions.
2 Installation instructions for Microsoft Windows Installing the Insight Management Agents The following is a list of services that are installed: • Insight Foundation Agents • Insight NIC Agents • Insight Storage Agents • Insight Server Agents • Web Agent • Event Notifier System requirements and preinstallation Insight Management Agents for Microsoft® Windows® are supported on HP ProLiant servers. The agents require the hardware and software described in Table 2-1.
7. Click Install. 8. After the installation is complete, click Close. To install the SNMP service in Windows Server® 2003: 1. Select Start>Settings>Control Panel. 2. Click Add/Remove Programs>Add/Remove Windows Components. 3. From the Windows Components Wizard window, select Management and Monitoring Tools, and then click Next. 4. From the Management and Monitoring Tools window, select Simple Network Management Protocol. 5. Click OK. The Component Wizard window appears. 6.
Storage Tab Screen The Storage tab enables you to disable Fibre Agent tape support: • To disable Fibre Array Tape Support, click the check box. • To enable Fibre Array Tape Support, clear the check box. SNMP Settings tab screen The SNMP Settings tab enables you to do the following: • Server Role—Displays the description of the system’s role or function. You can also set the Server Role text on multiple devices by creating a Group Configuration Task in Systems Insight Manager.
Asynch Mgmt tab screen NOTE: Remote Access Service (RAS) must be installed to have access to the Asynch Mgmt tab screen. The Asynch Mgmt tab enables you to do the following: • Enable asynchronous management traps—Enables traps to be sent through RAS to a remote management console over a modem. You must also enter the following data for asynchronous management trapping to occur: • Destination phone—Dials the number. • User name and password—Logs on to the remote machine.
2. Log in to Windows® as a user with administrator rights. 3. Execute the cp00xxxx.exe file that contains the HP Insight Management Agents. The HP ProLiant Package Setup window appears. 4. Click Install. The extraction progress starts. 5. The HP ProLiant Setup dialog box appears. Setup is ready to begin the install process. Click Install.
Table 2-3 Examples of single component installations Command line input Result cp002575 /s /f /r This command line installs the CP002575.EXE component, forcing the component to install over an existing version, and enabling the server to reboot automatically if needed. The GUI is not displayed. Return codes When each Smart Component has finished running, the component reports a return code to the operating system or the calling application.
3 Installation instructions for NetWare System requirements and preinstallation Insight Management Agents for Servers for Novell NetWare require the following hardware and software.
Table 3-3 Insight Foundation Agents File name (NLM) Description CPQHOST.NLM HP Management Host Agent CPQTHRSA.NLM HP Threshold Agent CPQAGIN.NLM HP Server Agent Installation and Configuration Utility CPQWEBAG.NLM HP Web-enabled Server Management Agent Table 3-4 Insight Server Agents File name (NLM) Description CPQBSSA.NLM HP Base System Agent CPQHTHSA.NLM HP Server Health Agent CPQRISA.NLM HP Remote Insight Agent Table 3-5 Insight Storage Agents File name (NLM) Description CPQIDESA.
Read this installation procedure completely before installing the software. The installation varies, depending on whether you are installing all four of the Insight Management Agents for Servers components, or updating only specific components. To install the Server Agents for NetWare from the Management CD: 1. Insert the Management CD into the CD-ROM drive. 2. Mount the CD mounted as a NetWare volume. 3.
Console component The console component of Power Manager is an addition to Insight Manager. Insight Manager must be installed before installing the Power Manager software. When viewing UPS information on servers with the Power Manager server component installed, the Power Manager screen is displayed. When viewing UPS information on servers without the Power Manager server component, the traditional UPS screen is displayed.
With this method of registration, CPQCLNT.EXE writes the client INI file to the CPQDATA directory specified by the -F command line option. Installing and updating Web Agents on multiple NetWare systems The following procedure is intended for administrators wanting to use software distribution tools to distribute agent settings from one server to multiple servers on the network.
your environment configuration. Be sure to place the alarm destination address under the appropriate protocol section and to indent each address with at least one space. Verify that the network address of the management console where Insight Manager runs is included in TRAPTARG.CFG.
Configuring agents NOTE: CPQBSSA must be installed to enable Insight Manager to verify that the system is manageable. To configure Management Agents for Servers for NetWare: 1. 2. At the NetWare console prompt, enter the following command: LOAD CPQAGIN Select the Configure Existing NetWare Agents option to display a list of Management Agents for Servers to be configured. The next screen enables you to select which agents you want to configure. 3.
4 Where to go for additional help In addition to this guide, the following information sources are available: • HP Insight Management Agents 7.30 User Guide • HP Insight Manager software Telephone numbers For the name of the nearest HP authorized reseller, see the HP website, http://www.hp.com/service_locator. For HP technical support: • In North America: • Call 1-800-HP-INVENT (1-800-474-6836). This service is available 24 hours a day, 7 days a week.
Index codes, 9; single component, 8; SmartStart CD, 6; SNMP, 5; Web Agents on multiple systems, 15 A Asynch Mgmt tab, 7 C client management support, 14 command line: arguments, 8; examples, 9; syntax, 8 community strings, SNMP, 16 configuration: Management Agents for Servers, 17 configuring: Event Notifier, 10 console, power management, 14 CPQCLNT.EXE, 14 CPQCLNT.
