Ignite-UX Release Notes (769572-001, March 2014)
Table Of Contents
- Ignite-UX Release Notes
- Contents
- HP secure development lifecycle
- 1 Related information
- 2 Announcements
- 3 Ignite-UX releases
- Version C.7.18.63 (March 2014 AR and Web release)
- Version C.7.17.391 (November 2013 - web release only)
- Version C.7.17.361 (October 2013 – This version is suspended and unsupported.)
- Version C.7.16.283 (March 2013)
- Version C.7.15.254 (September 2012)
- Version C.7.14.274 (March 2012 - web release only)
- Version C.7.14.264 (March 2012)
- Version C.7.13.259 (September 2011 - web release only)
- 4 General features
- 5 Known issues
- 6 Known problems and workarounds
- Required patches
- General issues
- Networking issues
- User interface issues
- Issues when installing from archives
- Common problems loading patches
- make_[tape|net]_recovery issues
- Log file issues
- Security issues
- Cluster File System(CFS) issue
- September 2004 or earlier Itanium based VxVM golden image load failure
- Memory File System(MemFS) issue
- Encrypted Volume and File System(EVFS) issue
- Disk space issues using VxVM & hard drive models ST318203[FL]C
- VxVM used for OS content with non-VxVM root volume install
- Support issue for B.11.11 installs
- 7 Compatibility and installation requirements
- 8 Native language support
- 9 Documentation feedback
may result in errors or failure. Recovery archives should not be created which contain data
residing on large storage units listed above.
NOTE: Ignite-UX is not intended to be used instead of backup tools to save or restore large
quantities of application data.
• When a golden image is created for a B.11.23 or B.11.31 client using the pax format of the
pax command, it is not possible to run archive_impacts on it from the server if the server
is not running at least B.11.23 with the PAX-Enh product installed because currently there is
no version of the pax command for B.11.11 that understands the pax format.
• The size of individual swap/dump and swap volumes created by Ignite-UX during a cold
install or recovery on HP-UX 11i v1 is limited to 128 GB. On HP-UX 11i v2 and later the limit
is 1TB from Ignite-UX version C.7.16.283 onwards. The following table shows the maximum
sizes for different volumes that Ignite-UX can create:
Table 13 Supported sizes of volumes by Ignite-UX
11.3111.2311.11
1TiB1TiB1TiBUnused
1TiB1TiB128GiBSwap
4GiB*4GiB*4GiB*Dump
1TiB**1TiB**128GiB**Swap/Dump
*if there is a disk with a capacity larger than this it becomes the new maximum value. In
practical terms this value can never be reached if the largest disk is less than 1TiB in size since
dump and dump/swap volumes must be contiguous.
**The smallest of this value or maximum dump size.
Networking issues
• Ignite-UX Hewlett-Packard network interface support matrix.
The only interfaces supported for performing a network boot from a server are the built-in
ethernet (10-Base-T, 100-Base-T, and Gigabit) on all newer systems. The T, V, H, G, I, E class
and 9000/8*7S systems do not support network boot. Other network interfaces that are
supported (see the table below) can only be used when the system is booted using the
"bootsys" command or booted from an Ignite-UX tape or CD. See the bootsys(1M) and
make_boot_tape(1M) manpages.
Table 14 Supported network interfaces
NotesAmount of supportDriverType
1fulllan210-base-T
1fulllan310-base-T
1fullbtlan100-base-T
none100VG
full, 32-bit onlyfddi0EISA FDDI
fullfddiHPPB FDDI
2may workfddi3HSC/GSC FDDI
fullfddi4PCI FDDI
2,3may worktokenEISA token
24 Known problems and workarounds