Ignite-UX Release Notes (769572-001, March 2014)
Table Of Contents
- Ignite-UX Release Notes
- Contents
- HP secure development lifecycle
- 1 Related information
- 2 Announcements
- 3 Ignite-UX releases
- Version C.7.18.63 (March 2014 AR and Web release)
- Version C.7.17.391 (November 2013 - web release only)
- Version C.7.17.361 (October 2013 – This version is suspended and unsupported.)
- Version C.7.16.283 (March 2013)
- Version C.7.15.254 (September 2012)
- Version C.7.14.274 (March 2012 - web release only)
- Version C.7.14.264 (March 2012)
- Version C.7.13.259 (September 2011 - web release only)
- 4 General features
- 5 Known issues
- 6 Known problems and workarounds
- Required patches
- General issues
- Networking issues
- User interface issues
- Issues when installing from archives
- Common problems loading patches
- make_[tape|net]_recovery issues
- Log file issues
- Security issues
- Cluster File System(CFS) issue
- September 2004 or earlier Itanium based VxVM golden image load failure
- Memory File System(MemFS) issue
- Encrypted Volume and File System(EVFS) issue
- Disk space issues using VxVM & hard drive models ST318203[FL]C
- VxVM used for OS content with non-VxVM root volume install
- Support issue for B.11.11 installs
- 7 Compatibility and installation requirements
- 8 Native language support
- 9 Documentation feedback
Table 10 HP-UX release/architecture combinations supported on Ignite-UX version C.7.14.264
HP Integrity systemsHP 9000 systemsHP-UX release
NoYesB.11.11
YesYesB.11.23
YesYesB.11.31
After downloading from the web, this version can be installed on any server running on any one
of the above HP-UX releases.
Ignite-UX version C.7.14.264 contains the following new feature:
The following manual page entries are either added or updated:
• ignite-client(1M)
• ignite-config(1M)
• ignite-ui(1M)
• ignite-version(1M)
• ignite(1M)
• instl_adm(4)
• make_net_recovery(1M)
Fixes for the following Change Requests:
• QXCR1001047654—While saving a configuration, if the Physical Volumes(PVs) belong to
a Physical Volume Group(PVG), they are not listed under the volume group.
• QXCR1001065414—The instance numbers for legacy disk DSFs is recovered correctly by
Ignite-UX.
• QXCR1001099187—During tape recovery, APA starts only when networking is enabled.
• QXCR1001111979—Legacy DSFs for ciss-driver based HBAs are recovered properly with
no stale DSFs left around.
• QXCR1001129212—The bootable flags for the paths are appropriately set before the
preferred path is selected.
• QXCR1001130947—SAS disks are now recovered correctly even when multiple paths pointing
to the same disk are present in a different order from that of the archive.
• QXCR1001131156—The expected value of the final size of the LIF volume is now set to the
maximum value possible.
• QXCR1001135320—The APA interfaces are commented out from the /etc/rc.config.d/
netconf file during recovery.
• QXCR1001139466—Recovery of servers that use only aggregate lan interfaces has been
made more efficient.
• QXCR1001139486—Post recovery, Ignite-UX comments out entries of the
INTERFACE_MODULES variable at the same index as the other variables that make up a
definition of the IP address to apply to an interface in the netconf file.
• QXCR1001141025—The make_*_recovery command is changed to call list_expander
with the -m option, which allows archiving of files of size greater than 8GB.
• QXCR1001144550—Available free space in a file system is calculated using a 64-bit variant
of statvfs64 system call. This is for servers with greater than 2TB file systems to work as
expected.
16 Ignite-UX releases