Ignite-UX Release Notes (769572-001, March 2014)
Table Of Contents
- Ignite-UX Release Notes
- Contents
- HP secure development lifecycle
- 1 Related information
- 2 Announcements
- 3 Ignite-UX releases
- Version C.7.18.63 (March 2014 AR and Web release)
- Version C.7.17.391 (November 2013 - web release only)
- Version C.7.17.361 (October 2013 – This version is suspended and unsupported.)
- Version C.7.16.283 (March 2013)
- Version C.7.15.254 (September 2012)
- Version C.7.14.274 (March 2012 - web release only)
- Version C.7.14.264 (March 2012)
- Version C.7.13.259 (September 2011 - web release only)
- 4 General features
- 5 Known issues
- 6 Known problems and workarounds
- Required patches
- General issues
- Networking issues
- User interface issues
- Issues when installing from archives
- Common problems loading patches
- make_[tape|net]_recovery issues
- Log file issues
- Security issues
- Cluster File System(CFS) issue
- September 2004 or earlier Itanium based VxVM golden image load failure
- Memory File System(MemFS) issue
- Encrypted Volume and File System(EVFS) issue
- Disk space issues using VxVM & hard drive models ST318203[FL]C
- VxVM used for OS content with non-VxVM root volume install
- Support issue for B.11.11 installs
- 7 Compatibility and installation requirements
- 8 Native language support
- 9 Documentation feedback
Table 7 HP-UX release/architecture combinations supported on Ignite-UX version C.7.16.283
HP Integrity systemsHP 9000 systemsHP-UX release
NoYesB.11.11
YesYesB.11.23
YesYesB.11.31
After downloading from the web, you can install this version on any server running on any one of
the HP-UX releases listed in the table.
Ignite-UX version C.7.16.283 includes the following new features:
• Support for cluster DSF.
• Support for boot disk size greater than 2TB (upto 16TB max) during cold installation and
recovery.
This release also includes fixes for the following Change Requests:
• QXCR1001056377—Boot disk > 2TB in size can be used now for installing HP-UX 11i v3.
• QXCR1001113271—Support for cDSFs into Ignite-UX.
• QXCR1001189838—Agile ctl device information is added to io.info and is used for
recovery.
• QXCR1001225407—After Ignite-UX recovery, LVM commands will not fail on systems that
have SRP installed.
• QXCR1001228658—During Ignite-UX upgrade on the server containing recovery commands
depots,swlist does not complain about the missing INFO file.
• QXCR1001235981—Legacy disk instance numbers are mapped correctly.
• QXCR1001239595—On HP-UX 11i v2 and later, Ignite-UX now supports the size of swap,
dump, and unused logical volumes up to 1TB in size instead of the previous limit of 128GB.
Larger amounts of swap/dump or swap volumes can be utilized in disk or volume groups
created during a cold install or recovery by defining multiple swap/dump or swap volumes.
The limit for unused volumes on 11i v1 is 1TB. However the limit for swap and dump have
not been increased.
• QXCR1001245156—Deleting a disk with multiple paths deletes all the paths.
• QXCR1001247114—Legacy CD/DVD devices instance numbers are recovered properly.
• QXCR1001247383—If pax archive is set in the defaults file, diagnostic messages are
displayed.
Version C.7.15.254 (September 2012)
The C.7.15.254 release of Ignite-UX supports the following HP-UX release/architecture combinations:
Table 8 HP-UX release/architecture combinations supported on Ignite-UX version C.7.15.274
HP Integrity systemsHP 9000 systemsHP-UX release
NoYesB.11.11
YesYesB.11.23
YesYesB.11.31
After downloading this version from the web, it can be installed on any server running on any one
of the above HP-UX releases.
Ignite-UX version C.7.15.254 contains the following new feature:
14 Ignite-UX releases