High Availability Monitors Version A.04.00 Release Notes HP-UX 11i v1 Manufacturing Part Number: B5736-90044 E0603 U.S.A. © Copyright 1997, 2003 © Hewlett-Packard Company. All rights reserved.
Legal Notices The information in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this manual, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be held liable for errors contained herein or direct, indirect, special, incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Trademark Notices X Window System is a trademark of the Massachusetts Institute of Technology. MS-DOS and Microsoft are U.S. registered trademarks of Microsoft Corporation. OSF/Motif is a trademark of the Open Software Foundation, Inc. in the U.S. and other countries.
1 High Availability Monitors Version A.04.
High Availability Monitors Version A.04.00 Release Notes for HP-UX 11i v1 Announcement Announcement High Availability Monitors (B5736DA) A.04.00 runs on the HP-UX 11i v1 operating system. The following high availability monitors are included in this bundle: • HA Disk Monitor checks the status of LVM managed disks and detects disconnected buses, power-failed or missing disks, and stale or missing mirrors.
High Availability Monitors Version A.04.00 Release Notes for HP-UX 11i v1 What’s in This Version What’s in This Version The A.04.00 version of High Availability Monitors for HP-UX 11i v1 operating system runs on the PA platform. HA Monitors contains a suite of monitors. Among them, MIB Monitor is used for monitoring the availability of LAN interface. In HP-UX 11i v1, with introduction of IPv6, there are new interface monitoring MIBs.
High Availability Monitors Version A.04.00 Release Notes for HP-UX 11i v1 What’s in This Version All HA Monitors can be used with enterprise system management software such as HP OpenView. To work with HA Monitors using the EMS GUI: • Log on to the system as root and enter sam to open SAM. In SAM, double-click on the Resource Management icon, and then double-click on the Event Monitoring Service icon to invoke EMS. • Use the EMS GUI to configure a monitoring request to warn you before a system failure.
High Availability Monitors Version A.04.00 Release Notes for HP-UX 11i v1 What’s in This Version Further Information Documents are found at http://docs.hp.com. Click HP-UX for operating system information. Click High Availability for information about Event Monitoring Service, HA Monitors, MC/ServiceGuard and ServiceGuard Extension for RAC (formerly known as ServiceGuard OPS Edition) A.11.15.00. Support information is available from the Hewlett-Packard Electronic Support Center: http://www.itrc.hp.
High Availability Monitors Version A.04.00 Release Notes for HP-UX 11i v1 Known Problems and Workarounds Known Problems and Workarounds The following are known problems with the HA Monitors product: JAGab04570: Delay in changing resource state What is the problem? When SNMP connectivity to dbsnmp (Oracle SNMP) fails, EMS correctly reports that there are “no instances” of the /rdbms/server/status resource.
High Availability Monitors Version A.04.00 Release Notes for HP-UX 11i v1 Known Problems and Workarounds • What is the workaround? Install each vendor’s database on different systems. If that is not feasible, and you need to monitor Informix databases, then stop the Oracle SNMP subagent (dbsnmp) and listener (tnslsnr), and run only the Informix SNMP subagent.
High Availability Monitors Version A.04.00 Release Notes for HP-UX 11i v1 Compatibility Information and Installation Requirements Compatibility Information and Installation Requirements The HA Monitors software should be installed on each node that you want to monitor. If you want to monitor the management station, then HA Monitors should be installed on the management station also. Compatibility with HP-UX Releases HA Monitors version A.04.00 runs on the HP-UX 11i v1 operating system only.
High Availability Monitors Version A.04.00 Release Notes for HP-UX 11i v1 Compatibility Information and Installation Requirements Requirements for Database Monitor Users: The Database Monitor is supported for the Oracle Enterprise Server version 9.2 and Informix version 9.3. Before you begin to monitor your database services, you must install the following components: • For Oracle: — Oracle Net8 (for networking) — Oracle Intelligent Agent (for SNMP support) and any patches.
High Availability Monitors Version A.04.00 Release Notes for HP-UX 11i v1 Compatibility Information and Installation Requirements • EMC Symmetrix arrays for both Fibre Channel and SCSI disks • Hewlett-Packard High Availability Storage System • Single-spindle SCSI disks • HP High Availability Disk Array, Model 30 Fibre Channel • HP SureStore E Disk Array XP256 for Fibre Channel and SCSI • HP SureStore E Disk System, models FC10 and FC60. The disk monitor does not support HP-IB or HP-FL disks.
High Availability Monitors Version A.04.00 Release Notes for HP-UX 11i v1 Patches and Fixes in This Version Patches and Fixes in This Version Required and Recommended Patches The contents of HA Monitors A.03.20.01 and A.03.40 has been incorporated into A.04.00 release.
High Availability Monitors Version A.04.00 Release Notes for HP-UX 11i v1 Patches and Fixes in This Version Resolution: Now, the UNAVAIL status is a valid status recognized by the service monitor. JAGae05308 Problem: When adding monitoring events using EMS GUI, the following error message is displayed: "The selected monitor is not currently available" This usually happens when the event added is the first event. The second attempt to add the event is generally successful.
High Availability Monitors Version A.04.00 Release Notes for HP-UX 11i v1 Patches and Fixes in This Version JAGad51995 Problem: Persistent monitoring requests for diskmond are deleted by EMS. After system boot or restart of EMS (specifically: restart of p_client and diskmond), persistent monitoring requests for diskmond may be deleted by EMS. Resolution: For disk monitors that are being initialized, registrar now sends RM_NOT_READY signal to the client.
High Availability Monitors Version A.04.00 Release Notes for HP-UX 11i v1 Software Availability in Native Languages Software Availability in Native Languages HA Monitors version A.04.00 does not provide native language support.
High Availability Monitors Version A.04.00 Release Notes for HP-UX 11i v1 List of Documents available with the Product List of Documents available with the Product The following document is available with the HA Monitors version A.04.00: • Using High Availability Monitors manual This document is available on http://docs.hp.com/hpux/ha/index.html.
