HP StorageWorks Power Supply Replacement Instructions (5697-5245, March 2006)

ManualsBrandsHP ManualsStorageHP EVA4000/6000/8000 Disk Arrays

HP StorageWorks

Power Supply Replacement

Instructions

These instructions apply to the MSA1500 cs, MSA20,

and EVA 4000/6000/8000 products. The part may

also be used in other HP products. Please refer to

documentation for your speciﬁc product for detailed

replacement instructions.

Printed on at least 50% total recycled ﬁber with at least

10% post-consumer paper.

L.P.

Second edition March 2006

Product names mentioned herein may be trademarks of their

respective

companiesasreﬂected by an associated footnote.

The information in this document is subject to change without

notice.

Printed in the U.S.A.

www.hp.com

*5697-5245*

Warranty Inform

ation

If the product in

whichthispartisbeingreplacedisstillunder

HP warranty, then the replacement part(s) referred to in these

Replacement Instructions is provided under the terms and conditions

of the Hewlett-Packard Company Limited Warranty for that

product. A copy of this Limited Warranty may be viewed at:

ttp://h1 8006.www1.hp.com/products/storageworks/warranty.html

If this is a tra

de sale part (product out of warrant y), then the replacement

part(s) refe

rred to in these Replacement Instructions is provided under

HP's express

limited warranty statement, which may be viewed at:

ttp://cust

omerops.corp.hp.com/1sw/pdm_om/warranty_support/

policies/2

330100.doc

The replace

ment part takes on either the Limited Warranty Period of the

part being r

eplaced or a ninety-day period that begins upon installation

of the replacement part, whichever is greater.

The only wa

rrantyforthisreplacementproductisasnotedabove.

Nothing in

these replacement instructions should be construed as

constituting an additional warranty. The information provided in these

replacem

ent instructions is provided "AS IS" and HP is not liable for

technic

al or editorial errors or omissions contained herein.

About This Document

This document describes the procedure for replacing the power

supply used in MS A 1500 cs and MSA20 products, and EV A

4000/6000/8000 products.

NOTE:

Because this component is used in sever al products, the

drawings may reﬂect a different enclosure than the one you

have. The removal and replacement procedure is the same

for each product.

Before you begin

Observe the following precautions when replacing a power supply.

CAUTION:

Remov

ing a power supply signiﬁcantly changes the air ﬂow

within the enclosure. Both power supplies must be installed for

the enclosure to cool properly. If a power supply fails, leave it

in place in the enclosure until a new power s upply is available

to install.

If cabling is obstructing access to the power supply, carefully

mov e the cables out of the way to avoid loosening any

connections.

Parts can be damaged by electrostatic discharge. Use proper

anti-static protection. Refer to the documentation that shipped

with your system for additional information.

Have a copy of the product User Guide available for reference.

You can download a copy of the User Guide from the product

support page on the HP web site.

Page 1

Summary of content (3 pages)

PAGE 1
HP StorageWorks Power Supply Replacement Instructions Warranty Information If the product in which this part is being replaced is still under HP warranty, then the replacement part(s) referred to in these Replacement Instructions is provided under the terms and conditions of the Hewlett-Packard Company Limited Warranty for that product. A copy of this Limited Warranty may be viewed at: http://h18006.www1.hp.com/products/storageworks/warranty.
PAGE 2
Verifying component failure Before replacing a power supply, use the following methods to verify the component failure. EVA Products CAUTION: If Command View EVA does not present a status consistent with that of the power supply status indicator, or if Command View or the System Event Analyzer indicates multiple hardware failures, contact HP support for assistance. The HP support web site is located at http://www.hp.
PAGE 3
Removing a power supply 1 1. Disconnect the AC power cord from the power supply. 2. While moving the wine-colored latch to the left (1, Figure 3), grasp the handle and pull the power supply out of the enclosure (2). 2 0138a Figure 4 Installing a power supply Verifying proper operation After replacing the power supply, check the following to verify that the component is operating properly: Figure 3 Removing a power supply Installing a power supply 1.